大学无机化学中“原电池”的启发探究式教学实践*

介绍了大学无机化学课堂中“原电池”部分的教学实践。通过启发-探究式教学模式,启发学生把常见的氧化还原反应,经过不断的设问和探究,最终设计成原电池,实现了通过原电池装置来证实氧化还原反应发生了电子传递的教学目的。学生在教师的启发下探究、分析、推导、创新和修正,使学生清晰地认识到知识的前后逻辑关系,对氧化还原反应概念、原电池装置有更深刻的理解,培养了学生的科学辩证思维能力。     

铂纳米颗粒增强MnO2纳米棒对CO和挥发性有机化合物的氧化活性

通过水热法合成了纯相的α-MnO2和δ-MnO2纳米棒,并利用溶胶固定化工艺制备了负载铂纳米颗粒的Pt/MnO2材料.通过透射电镜(TEM),X射线粉末衍射(XRD),扫描电镜(SEM),X射线光电子能谱(XPS),N2吸附-脱附和H2程序升温还原(H2-TPR)技术研究了样品的微观结构和吸附活性位,探查了CO和挥发性有机化合物(VOCs)(苯和甲苯)在催化剂上的催化发光(CTL)性质.结果表明:铂颗粒在α-MnO2和δ-MnO2载体上以高分散状态存在,负载过程不会影响α-MnO2纳米棒的晶相结构,但会导致δ-MnO2纳米棒产生结构变化.经XPS证实不是Pt与其发生了反应.α-和δ-MnO2纳米棒对CO、苯和甲苯的催化氧化都具有很高的活性,δ-MnO2的活性略高于α-MnO2相.虽然N2吸附-脱附实验结果证实Pt负载会导致MnO2纳米棒比表面积的下降,但H2-TPR结果显示Pt和MnO2之间会产生强烈的相互作用,显著增强其催化活性,且Pt/δ-MnO2活性高于Pt/α-MnO2.催化氧化发光研究表明,这四种催化剂活性顺序是α-MnO2≤δ-MnO2相似文献   

吸氧腐蚀的实验创新设计

使用被氯化钠溶液浸湿的2片滤纸包住锌片和铜片,连接好电流表构成原电池,使学生能够直观地看到吸氧腐蚀的现象,推测出原电池正负极的电极反应原理,从而进一步理解课本中的铁的吸氧腐蚀是由于铁钉中含有碳等杂质与铁形成的微电池的电化学腐蚀原理。     

用MS-PSR技术研究甲烷部分氧化反应的引发过程

借助质谱 程序升温表面反应(MS TPSR)技术研究了NiO/悛睞l2O3、700 ℃ H2还原 后的Ni0/悛睞l2O3和添加Pt的NiO/悛睞l2O3催化剂(分别记为NiO、Ni0和Pt NiO)上甲烷 部分氧化反应(POM)的引发行为.结果表明,在CH4＋O2气氛下NiO和Ni0具有相同的引发行为 , Ni0在反应气氛下首先被氧化为NiO.在低于760 ℃时, CH4和O2在NiO上发生深度氧化反 应生成H2O和CO2,在770 ℃开始逐渐引发POM反应. Pt NiO在520 ℃左右就能引发POM反应 .在流化床反应器中Pt NiO催化剂500 ℃左右引发POM反应,并且具有与Ni0基本相同的反应 性能,因此添加Pt有利于氧化镍还原为Ni0,从而降低了POM反应的引发温度.     

水汽-CO_2环境下Pt/CeZrO_2催化剂的CO氧化性能研究

采用浸渍法制备了Pt/Ce0.6Zr0.4O_2粉末催化剂,涂覆到蜂窝陶瓷载体表面得到整体式催化剂。考察了Pt含量及焙烧温度对催化剂在水汽-CO_2环境下催化CO氧化性能的影响,并用XRD,TEM和H2-TPR等手段对载体和催化剂进行了表征。结果表明,在空速50000 h-1的反应条件下,当焙烧温度为300℃时,3.0Pt/Ce0.6Zr0.4O_2整体式催化剂的CO氧化活性最高,反应温度200℃时,CO转化率为87%,具有较高的水汽-CO_2环境下的CO氧化活性。通过对2.0Pt/Ce0.6Zr0.4O_2催化剂在无水汽,无CO_2,无水汽-CO_2及水汽-CO_2环境下的对比实验,发现水汽和CO_2对催化剂的活性有明显的抑制作用,水汽的影响比CO_2的影响要更大一些。这说明水汽、CO_2和CO对催化剂存在竞争吸附。结合催化剂的H2-TPR表征结果,发现催化剂的还原能力越高,相对应的CO氧化活性也越高。添加适量的Pt有利于提高催化剂的还原能力,从而提高其活性,但是过量的Pt会使催化剂活性下降。     

负载型Au（Pt）／Co3O4催化上H2与CO的共氧化行为

用共沉淀法制备了Au/Co3O4,Pt/Co3O4及Au- Pt/Co3O4催化剂,并考察了其对H2与CO在O2过量情况下完全共氧化的催化作用。结果表明,在三种催化剂上H2与CO之间都存在复杂且各不相同的相互作用。与Pt/Co3O4催化剂上不同,在Au/Co2O4和Au-Pt/Co3O4催化剂上H2严重抑制CO的氧化。同时,Au-Pt/Co3O4催化剂上H2与CO能够在较低的温度（76℃）下有效地实现完全共氧化。TPR结果表明,与Pt/Co3O4催化剂相比,Au-PtCo3O4催化剂上Au的存在使Pt的还原峰消失。     

利用手持技术探究原电池“电极反转”双模型的反应机理

基于手持技术表征原电池基准态与极端态工作原理的差异性,继而探究铁和铝分别与铜在浓硝酸中构成的2种极端态原电池在发生电极反转时硝酸浓度的临界值。通过双模型对比实验,帮助学生更加直观、准确、深入地建构原电池模型,同时丰富学生对元素周期律、金属活动性以及氧化还原反应等关联性知识的认知与理解。     

原电池负极上的副反应探析

在原电池中 ,理论上 ,是在负极上发生氧化反应 ,在正极上发生还原反应 ,电子由负极通过外电路流向正极。但是 ,实际进行原电池的实验时 ,往往有副反应发生 ,即负极上也发生还原反应。以Cu -Zn原电池为例 ,如图 1装置 ,理论上的反应是 :负极 (Zn) :Zn%D 2e%D Zn2 +　 (氧化反应 )　　正极 (Cu) :2H++ 2e-H2 ↑　 (还原反应 )其现象应该是 ,在正极上有气泡产生 ,而负极逐渐消耗 ,没有气泡出现。但是 ,实际上 ,正极和负极上通常都有气泡产生 ,即负极上也有氢离子得电子的副反应发生。由于副反应的存在 ,原电池的效率就大大降低了。图 1对于…     

钴和钾对Pt/γ-Al2O3上CO选择性氧化的助催化作用

 添加Co或/和K助催化剂可在不同程度上改善Pt/γ-Al2O3催化剂对富氢气氛下CO选择性氧化的性能. 利用H2-TPR,CO-TPD和FT-IR等表征手段,探讨了不同助催化剂的作用机理. 结果表明,Co/Pt/γ-Al2O3能显著降低富氢气氛下CO选择性氧化的温度,主要原因是Co与Pt的相互作用使Pt的电子性能发生了改变,从而削弱了Pt对CO的吸附,使催化剂表面CO的线式吸附消失; Co的添加还促进了易分解的碳酸氢盐物种的生成,同时未完全还原的CoOx物种可提供活性氧促进CO的转化. 助催化剂K一方面促进了Pt向CO反馈电子,从而活化吸附的CO,提高了催化剂的低温活性;另一方面促进了难分解的甲酸盐物种的生成,从而抑制了部分活性位,需要更高的反应温度,而较高温度下会发生氢气氧化反应的竞争,使CO选择性氧化反应的活性和选择性受到影响. 同时添加K和Co的催化剂中,K可促进CoOx的还原,使Co与Pt的相互作用变弱,即减弱了Co对Pt的助催化作用, 因此虽然其选择性有所改善,但活性介于单独添加Co或K的催化剂之间.     

载体性质对Pt催化剂H2选择催化还原NOx活性和选择性的影响

研究了Pt/MgO, Pt/γ-Al2O3, Pt/ZrO2和Pt/HZSM-5催化剂上H2选择催化还原消除NOx(H2-SCR)反应。结果发现, H2-SCR活性和N2生成选择性受催化剂中Pt的金属性以及载体的氮氧化物吸附能力影响很大。 HZSM-5的表面酸性使载体对NOx吸附能力较小,使担载Pt以较高的金属性存在,从而导致Pt/HZSM-5催化剂的高活性和高选择性。相反, Pt/MgO和Pt/γ-Al2O3催化剂较差的活性和选择性可归因于其载体的碱性表面、催化剂中Pt较低的金属性以及载体对氮氧化物较大的吸附能力。结合反应的原位红外光谱结果可以认为,在Pt/载体界面处亚硝酸根/硝酸根物种被还原为N2或N2O,取决于该处参与反应的活性H与这些含氮物种的相对数目。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.