环氧乙烷环氧丙烷共聚醚的研究进展

综述了环氧乙烷环氧丙烷共聚醚的聚合机理聚合工艺及其应用.环氧乙烷环氧丙烷共聚醚的聚合按其催化剂体系的机理可以分为阴离子聚合、阳离子聚合和配位聚合三类,其中阳离子聚合应用较少.在环氧乙烷和环氧丙烷开环聚合生成共聚醚的反应中,不同的反应工艺条件对生成的聚醚有着很大的影响.同样比例的环氧乙烷和环氧丙烷,因聚合反应器设计、反应器种类、起使剂种类催化剂种类与用量温度加料方式端基结构等的不同,所合成的共聚醚会产生不同的结构和性能.环氧乙烷环氧丙烷共聚形成的聚醚可以分为嵌段共聚醚和无规共聚醚两类.其中,嵌段共聚醚可以分为EPE和PEP两类.     

环氧乙烷-环氧丙烷无规共聚醚链结构的核磁共振研究

本文用NMR波谱方法研究了无规共聚醚(EPO)的链结构。首先对EPO的~1H和~(13)CNMR谱进行了讨论。并从序列结构随环氧丙烷(PO)含量的改变,分析了EPO的二元组序列和三元组序列结构,从~(13)C实验谱中归纳出EPO的取代基参数(SCS),清楚地揭示了EPO的~(13)C谱,SCS参数和序列结构之间的关系,在此基础上计算了EPO系列共聚物的序列分布和数均序列长度。     

水溶性聚合物和两亲聚合物:14.丙烯酰胺/2-丙烯酰胺基十六烷磺酸铵无规共聚物

水溶液中用硫酸亚铁-异丙苯过氧化氢氧化还原引发体系合成了丙烯酰胺(AM)/2-丙烯酰胺基十六烷磺酸铵(AMC_(16)SNH_4)无规共聚物。用元素分析、IR、~(13)C-NMR和~1H-NMR对其进行了表征。对水溶液性质的研究结果表明,与部分水解聚丙烯酰胺相比,这种新型共聚物有着优异的耐盐性、耐温性和贮存稳定性。     

聚酰胺-46的合成和结构研究(Ⅱ)──产物的基本表征和结构研究

用红外光谱、核磁共振和示差扫描量热分析等手段对聚酰胺－46进行了基本表征,并用广角X射线衍射和扫描隧道电子显微镜技术对其聚集态结构进行了分析.     

红外光谱-差示扫描量热法对聚烯烃共聚物中α-烯烃种类与含量的鉴别

利用傅立叶变换红外光谱(FTIR)研究了与不同α-烯烃共聚合的多种聚乙烯,并对共聚物的结构和类型进行了定性分析.由1 378、1 369 cm-1处的峰位置和峰强度判断聚烯烃的种类,由770、 899、784 cm-1处的峰判断α-烯烃的种类.利用差示扫描量热(DSC)热分级方法确定熔融峰的位置,并对共聚物中α-烯烃的含量进行了定量计算.     

5-氯-2-甲氧基苯甲酸与1,10-邻菲啰啉稀土配合物的合成、表征及热分解机理

合成了三种稀土配合物[Ln(5-Cl-2-MOBA)3phen]2(Ln=Nd(1),Eu(2),Ho(3);5-Cl-2-MOBA:5-氯-2-甲氧基苯甲酸根;phen:1,10-邻菲啰啉),通过元素分析、热重-微分热重-差示扫描量热(TG-DTG-DSC)、红外光谱(IR)、紫外光谱(UV)及摩尔电导等技术对标题配合物进行了表征.荧光光谱表明配合物(2)发出铕离子的特征荧光.用热分析/傅里叶变换红外(TG-DSC/FTIR)联用技术,阐明标题配合物的热分解反应机理,并分析了逸出气体的三维(3D)红外光谱.     

聚丙烯-聚乙烯嵌段共聚物和相应共混物的热分析

用DSC研究了预期为聚丙烯-聚乙烯两嵌段共聚物(PP-PE)和相应共混物(PP+PE)在热学性能上的差异。经用不同分子量的PP和PE及其共混物进行试验后发现,由于PP和PE在结晶时出现过冷的难易不同。在共混物降温热分析曲线上,当降温速率较快时仅出现一个放热峰,而降温速率较慢时出现PP和PE各自的结晶放热峰,从而解释了文献中的不同结果。并发现共混物的PP和PE熔融、结晶温度均较组分相同的嵌段共聚物的相应温度为高;嵌段共聚物中PP和PE的△H_f值均低于均聚物的△H_f值,而PE的值降低尤甚。我们认为这与嵌段间的共价键限制嵌段活动和结晶过程有关,从而确认DSC热分析可以作为识别是否为嵌段共聚物的一种方法. 本工作的结果表明,所研究的PP-PE试样具有嵌段结构。     

硫化对聚乙炔结构和性能的影响

本文利用DSC, FT-IR光谱对聚乙炔硫化产物进行了表征, 研究了聚乙炔硫化前后结构和性能的变化。采用量子化学CNDO/2晶体轨道方法, 首次对硫化聚乙炔的分子结构及电子性质进行理论计算, 探讨了硫化对聚乙炔结构和性能的影响。     

结晶-非晶共混体系的结晶行为研究——PEO/PMMA与PEO/PVA共混物

用DSC和傅里叶红外(FTIR)光谱表征PEO/PMMA和PEO/PVA共混体系的结晶行为。发现PEO/PVA体系的结晶度与其组成的变化是一致的;而PEO/PMMA体系的结晶度随非晶组分增加而下降的速度,从与组成变化一致到比后者快,但又随时间而改变。对此结晶/非晶共混体系的结晶度随组成和时间而变化的现象,可用体系的玻璃化转变温度(T_g)来解释。     

Surface immobilization of poly(ethylene oxide): Structure and properties

We covalently immobilized poly(ethylene oxide) (PEO) chains onto a fluorinated ethylene propylene copolymer (FEP) surface. On the FEP surface, aldehyde groups were first deposited by plasma polymerization of acetaldehyde or acrolein. Then, amino‐PEO chains were immobilized through Schiff base formation, which was followed by reduction stabilization with sodium cyanoborohydride. The PEO‐grafted polymer surfaces thus prepared were characterized by X‐ray photoelectron spectroscopy (XPS), atomic force microscopy, contact‐angle measurements, and protein adsorption. The dramatic increase in the C O intensity of the high‐resolution XPS C 1s spectrum, together with an overall increase in oxygen content, indicated the successful attachment of PEO chains onto the acetaldehyde plasma surfaces. The amount of grafted PEO chains depended on the superfacial density of the plasma‐generated aldehyde groups. The grafted monoamino‐PEO chains formed a brushlike structure on the polymer surface, whereas the bisamino‐PEO chains predominately adopted a looplike conformation. The PEO surface had a regular morphology with greater roughness than the aldehyde surface underneath. Surface hydrophilicity increased with the grafting of PEO. Also, the bisamino‐PEO‐grafted surface had slightly higher surface hydrophilicity than its monoamino‐PEO counterpart. These PEO coatings reduced fibrinogen adsorption by 43% compared with the substrate FEP surface. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2323–2332, 2000     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Synthesis, Purification and Characterization of Amphiphilic and Microphase Separated Graft Copolymer Polystyrene-g-Poly(ethylene oxide)

The present paper covers the poly (ethylene oxide) macromer with vinyl benzyl terminal group (PEO-VB) prepared by deactivation of the alkoxide function of mono-functional "living" PEO chains with vinyl benzyl chloride (VBC). The obtained macromers were subjected to careful purification and detailed characterization. A new kind of amphiphilic polystyrene-g-poly(ethylene oxide) (PS-g-PEO) with both mi-crophase separated and PEO side chains was synthesized from radical copolymerization of PEO-VB macromer with styrene monomer. An improved purification method, referred as "selective dissolvation", was established for the isolation of graft copolymers from the grafting products, and the purity and yield of the purified copolymers were satisfactory. The well-defined structure of the purified copolymers was confirmed by IR, 1H NMR and GPC. The bulk composition of the graft copolymers was determined by a well-established first derivative UV spectrometry. Various experimental parameters controlling the copolymeri     

Study of the Crystallization Kinetics. Poly(ethylene oxide) and a blend of poly(ethylene oxide) and poly(bisphenol A-co-epichlorohydrin)

A kinetic study of the crystallization of poly(ethylene oxide) (PEO) and of a blend of PEO+poly(bisphenol A-co-epichlorohydrin) (PBE) was performed by using DSC in a non-isothermal program at constant cooling rates. The curves obtained were analyzed by the Kissinger, Ozawa and Friedman methods, with determination of the kinetic parameters in each case. As a consequence of the presence of PBE, the kinetic parameters were altered, leading to the conclusion that PBE has some influence on the crystallization of PEO, modifying its mechanism. This revised version was published online in July 2006 with corrections to the Cover Date.     

Molecular motion in nanocomposites of poly(ethylene oxide) and montmorillonite

Motion of chains of poly(ethylene oxide) within the interlayer spacing of 2:1 phyllosilicate/montmorillonite was studied with ¹H and ¹³C NMR spectroscopy. Measurements of the ¹H NMR line widths and relaxation times across a large temperature range were used to determine the effect of bulk thermal transitions on polymer chain motion within the nanocomposites. The results were consistent with previous reports of low apparent activation energies of motion. Details of the frequency and geometry of motion were obtained from a comparison of the ¹³C cross‐polarity/magic‐angle spinning spectra and relaxation times of the nanocomposite with those of the pure polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1678–1685, 2001     

Solid state NMR study of intercalate complexes of poly(ethylene oxide) and small molecules

From solid state NMR spectra, a lower shielding of poly(ethylene oxide) (PEO) protons, in contrast to higher shielding of PEO carbons, has been found for PEO/hydroxybenzene and PEO/LiCF₃SO₃ complexes in comparison with neat PEO. The same PEO chemical shifts were found both for crystalline and amorphous phase of PEO/LiCF₃SO₃ polymer electrolyte, confirming the same interaction in both phases. Measurements of 2D ¹H CRAMPS exchange NMR spectra have been used to characterize proton distances in complexes of PEO and benzene derivatives. A close contact (∼ 0.3 nm) between aromatic and PEO protons was detected in some cases. From the measurements of the cross polarization ¹H → ¹³C, using Lee-Goldburg irradiation of ¹H nuclei, the distance between LiCF₃SO₃ carbon and the nearest PEO protons in the PEO/LiCF₃SO₃ complex was determined.     

Synthesis of model linear tetrablock quaterpolymers and pentablock quintopolymers of ethylene oxide

Multiblock copolymers of ethylene oxide, with four and five different blocks, were synthesized by the sequential anionic polymerization of styrene, isoprene, 2-vinyl pyridine, t-butyl methacrylate, and ethylene oxide with benzyl potassium as an initiator. The monomer sequence was based on the relative nucleophilicity of the active centers. Characterization of the multiblock copolymers by size exclusion chromatography (with refractive-index and UV detectors), membrane osmometry, and NMR spectroscopy confirmed that benzyl potassium is an efficient initiator for the synthesis of well-defined multiblock multicomponent copolymers of ethylene oxide. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2166–2170, 2002     

Influence of DC electric field on both crystalline structure and conductivity of poly(ethylene oxide)10:LiClO4 electrolyte

The dynamic ionic conductivity and polarizing morphology of poly(ethylene oxide)₁₀:LiClO₄ (PEO₁₀:LiClO₄) electrolyte membranes under different direct current electric fields (EFs) were simultaneously investigated. PEO molecular chains were found to rearrange during the migration of charge carriers, and the rearrangement of PEO molecular chains dramatically affected the conductivity of the electrolyte membrane. No noticeable differences of conductivity and polarizing morphology between the heating and cooling process were observed when the EF was absent. However, the conductivity of the membrane was remarkably enhanced after applying an EF and after carrying out a heating–cooling loop. Differential scanning calorimetry and wide‐angle X‐ray diffraction of the sample with different treatments of both EFs and heating–cooling loops showed that the conductivity enhancement or reduction after loading special EFs and heating–cooling loops were attributed to the change of both the crystallite size of certain diffraction planes and the thickness of PEO lamellae. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Thermosetting polymer blends of unsaturated polyester resin and poly(ethylene oxide). I. Miscibility and thermal properties

The miscibility and thermal properties of polyethylene oxide(PEO)/oligoester resin (OER) blends and PEO/crosslinked polyester (PER) blends were studied by differential scanning calorimetry (DSC). The effect of quenching process on the crystallization behavior of PEO for these two systems were investigated and discussed in details. It has been found that a single, composition dependent glass transition temperature (T_g) was observed for all the blends, indicating that the two systems are miscible in the amorphous state at overall compositions. From the melting point depression of PEO, the interaction parameter χ₁₂ for PEO/OER blends and that for PEO/PER blends were found to be −1.29 and −2.01, respectively. The negative values of χ₁₂ confirmed that both PEO/OER blends and PEO/PER blends are miscible in the molten state. Quenching process has a greater hindrance on the crystallization of PEO/OER blends than on that of PEO/PER blends. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3161–3168, 1997