Application of wet effluent diffusion denuder for measurement of uptake coefficient of gaseous pollutants

The comparison of theoretical approaches describing the collection of analyte in the cylindrical wet effluent diffusion denuder (CWEDD) with experimental data is presented. Various absorption liquids were tested for the collection of formaldehyde (distilled-deionized water, H₂SO₄ solution), acetaldehyde (distilled-deionized water) and nitrous acid (distilled-deionized water, sodium carbonate and sodium bicarbonate solutions of various concentrations and sodium phosphate pH 6-8) in CWEDD. pH of absorption liquids significantly influences the collection of formaldehyde as well as nitrous acid. The collection efficiency of formaldehyde for 0.05 M H₂SO₄ as absorption liquid was generally higher than for distilled-deionized water. Absorption liquid pH markedly affected the collection efficiency of HONO too (with increasing pH the collection efficiency increase). Data derived by Gormley-Kennedy equation for all investigated compounds were overestimated especially for higher flow rates of air, data calculated with respect to Henry constant are not in good agreement with experimental data and are considerably depended on a determination of the Henry constant value. The CWEDD can be alternative tool for the determination of uptake coefficient. Obtained uptake coefficients were in good agreement with data found in other literature.     

Continuous chemiluminescence determination of formaldehyde in air based on Trautz-Schorigin reaction

A new continuous method for the determination of formaldehyde in air is described. A cylindrical wet effluent diffusion denuder is used for the collection of formaldehyde from air into a thin film of absorption liquid (distilled-deionized water). Formaldehyde in the denuder concentrate is on-line detected employing a chemiluminescence flow method based on a reaction of formaldehyde and gallic acid with hydrogen peroxide in an alkaline solution. The collection efficiency of formaldehyde is quantitative at the air flow rate of 0.5 L min⁻¹ (absorption liquid flow rate of 336 μL min⁻¹). The limit of detection (S/N = 3) is 0.60 μg m⁻³ HCHO (0.49 ppb). The calibration graph is linear up to 300 μg m⁻³ HCHO (244 ppb). The relative standard deviations of chemiluminescence method for 1 × 10⁻⁶ and 5 × 10⁻⁶ M HCHO are 2.87% and 1.49%, respectively. Acetaldehyde interferes negligible, other compounds do not interfere. The method was employed for formaldehyde measurement in ambient air. The comparison measurement illustrates the good agreement of results obtained by proposed method with those obtained by reference fluorimetric method.     

Determination of low boiling aldehydes in air and exhaust gases by using annular denuders combined with HPLC techniques

Summary An improved procedure for the HPLC determination of C₁–C₃ aldehydes in environmental samples is described. These air pollutants are quantitatively collected on annular denuders coated with 2,4-Dinitrophenylhydrazine and analyzed as hydrazone derivatives by HPLC with UV absorbance and voltammetric detection. Collection efficiencies of aldehydes are reported and compared with other available methods. Practical examples of the application of the method are given.This work has been part of the Dottorato di Ricerca program carried out at the University of Rome.Dedicated to Prof. Dr. A. Liberti on the occasion of his 70th birthday.     

Determination of folic acid by chemiluminescence based on peroxomonosulfate-cobalt(II) system

Based on the chemiluminescence (CL) phenomena of folic acid in peroxomonosulfate-cobalt(II) system, a rapid and sensitive CL method was developed for determination of folic acid in pharmaceutical preparations and its urinary metabolism processes. Under the optimum conditions, the relative CL intensity was linear over the concentration ranging from 10⁻⁹ to 8 × 10⁻⁷ mol L⁻¹ (R² = 0.9991) with a detection limit as low as 6 × 10⁻¹⁰ mol L⁻¹ (S/N = 3) and relative standard deviation was 2.63% for 2 × 10⁻⁸ mol L⁻¹ folic acid (n = 11). This method has been successfully applied to the determination of folic acid in tablets and human urine. The blank CL emission was yielded owing to the formation of singlet oxygen molecular pair from the quenching experiment of 1,4-diazabicyclo[2.2.2]octane, and pterine-6-carboxylic acid might be the degradation intermediate in this system and it also acts an energy acceptor and sensitizes the chemiluminescence based on the studies of the CL and fluorescence spectra.     

湿法消解测定食用明胶中的微量铬

建立了一种以HNO3-H2SO4-HClO4体系湿法消解食用明胶, 并采用分光光度计测定其中微量铬的新方法. 该方法的相对标准偏差1.8%～5.9%, 回收率93.3%～104.7% (n=8), 同时与原子吸收光谱法对照实验的误差均在4%以下. 本法可测定食用明胶中的微量铬.     

Determination of nitric acid in ambient air using diffusion denuder tubes

A method has been developed for the determination of gaseous nitric acid in air based on its separation from particulate nitrate aerosol using diffusion denuder tubes. An integrated value of nitric acid concentration in air is obtained. The experimentally derived absorption efficiencies of the diffusion denuder tubes ranged from 87.6 to 96.9%. The standard deviation of the method was calculated as 0.10 mug/m(3) for nitric acid concentrations in the range 0.54-1.72 mug/m(3). A correction procedure, using two diffusion denuders in series, should be applied if measurements are made in the presence of high levels of nitrogen oxides.     

Annular diffusion denuder for simultaneous removal of gaseous organic compounds and air oxidants during sampling of carbonaceous aerosols

A specially designed annular diffusion denuder for simultaneous removal of organic gaseous compounds and atmospheric oxidants in carbonaceous aerosol sampling is presented. Various kinds of denuder coatings were compared with respect to the collection efficiency of both organic gaseous compounds and NO₂ and ozone. The optimum sorbent is a mixture of activated charcoal and sulfite on molecular sieve. To ensure high collection efficiency over long-term field operation, two annular diffusion denuders are combined in series. The first half of the first denuder is filled with Na₂SO₃ on molecular sieve (23 cm long layer) while the second half of the first denuder and the whole second denuder are filled with activated charcoal (the total length of the charcoal section is 67 cm).     

Superoxometal-catalyzed co-oxidation of alcohols and nitrous acid with molecular oxygen

A superoxochromium(III) ion, Cr_aqOO²⁺, acts as a catalyst for the co-oxidation of alcohols and nitrous acid with molecular oxygen according to the stoichiometry: CH₃OH+HNO₂+O₂→CH₂O + NO₃⁻ + H₂O+H⁺. The kinetics are second order in [HNO₂] and independent of the concentrations of the superoxochromium catalyst, substrate, and O₂. The proposed mechanism features the disproportionation of HNO₂ to NO and NO₂, both of which react rapidly with Cr_aqOO²⁺. The Cr_aqOO²⁺/NO reaction generates another equivalent of NO₂ and a mole of Cr_aqO²⁺, the active oxidant. The two-electron oxidation of the alcohol by Cr_aqO²⁺ produces Cr_aq²⁺, which reacts rapidly with O₂ to regenerate the catalyst, Cr_aqOO²⁺. The NO₂/Cr_aqOO²⁺ reaction yields the peroxynitrato complex, Cr_aqOONO₂²⁺, in a dead-end equilibrium process that has no effect on the catalytic reaction. The disproportionation of NO₂ yields the final nitrogen-containing product, NO₃⁻, and regenerates an equivalent of HNO₂. Under a fixed set of conditions, the relative catalytic efficiency (CE) of Cr_aqOO²⁺ decreases as its concentration increases owing to the competition between O₂ and Cr_aqOO²⁺ for the intermediate Cr_aq²⁺.     

Determination of cyanide using flow-injection multisensor system

A flow-injection multisensor system (FIMS) comprising potentiometric sensors of different types for determination of free cyanide activity in basic solutions for extraction of noble metals was developed. The solvent polymeric membrane sensors based on metalloporphyrin and crystalline sensors were combined in the sensor system. The system allowed determination of cyanide activity in the range 10⁻⁴–1 mol l⁻¹ with an error less than 5% in individual cyanide solutions and acceptable precision (about 20%) in process liquids. The system was able to analyse up to 20 samples per h. The FIMS was also applied to detecting of silver ions in the presence of cyanide. Chalcogenide glass sensor was used as the detector that ensured the precision of 20%.     

Infrared matrix isolation studies of complexes formed between dimethylsulfide, dimethyldisulfide and nitrous acid

The complexes formed by dimethylsulphide (DMS) and dimethyldisulphide (DMDS) with two isomers of nitrous acid have been observed, and characterised in argon and nitrogen matrices. The ν₁ OH stretching vibration of the perturbed trans-HONO monomer is 425 and 294 cm⁻¹ red shifted, respectively, for the DMS and DMDS complex in solid argon, and 441 and 301 cm⁻¹ in solid nitrogen. A large blue shift is also observed for the ν₃ NOH in-plane deformation mode: 101 and 80 cm⁻¹ for DMS–HONO-trans in argon and nitrogen matrices and 46 cm⁻¹ for DMDS–HONO-trans in nitrogen matrix. The results indicate formation of strong hydrogen bonds in the studied DMS–HONO and DMDS–HONO systems. The origin of the complicated shape of the ν₁ OH absorption is discussed. Similarities and differences between argon and nitrogen matrices are considered.     

Investigation of multiple-component diffusion through LLDPE film using an FTIR-ATR technique

An FTIR-ATR technique was developed to investigate the multiple-component diffusion properties of 2-octanone, hexyl acetate, octanal, limonene and linalool (equal volume mixture) in a linear low density polyethylene film. Diffusion coefficient (D) values determined for these compounds in the mixture were 7.02 × 10⁻¹⁰, 2.86 × 10⁻⁹, 1.09 × 10⁻⁹, 7.49 × 10⁻⁹ and 5.81 × 10⁻⁹ cm²/s, respectively. Compared with the diffusion of the individual permeants (1:4 permeant:ethanol, v/v), the D values of 2-octanone, hexyl acetate and limonene were lower in the mixture solution, while those of octanal and linalool were higher. Hansen solubility parameters (HSP) were used to elucidate the solubility properties of the permeants. Two-dimensional FTIR data analysis showed that diffusion of the test permeants in LLDPE occurred in the following sequence: limonene (first) → linalool → hexyl acetate → octanal → 2-octanone (last).     

Improved HPLC determination of aliphatic amines in air by diffusion and derivatization techniques

Summary Traces of C₁–C₄ aliphatic amines, sampled from ambient air on H₃PO₃-coated annular denuders, are derivatized with m-toluoyl chloride (MTC) in alkaline acetonitrile. The resulting derivatives are determined by reversed phase HPLC with ultraviolet detection at 230 nm. The detection limits of the individual amines are in the 1 to 5 picomole range corresponding to gasphase concentrations lower than 0.1 g m^–3 in air samples collected at 5 Lmin^–1 for one hour.     

Determination of aromatic hydrocarbons in air using diffusion denuders

The results of a study to evaluate a recently developed denuder sampling system for the determination of aromatic hydrocarbons in air are presented. Denuders of different lengths were tested in laboratory experiments by means of dynamically generated test gases at conditions similar to those at workplaces. Uptake rates, adsorption capacities as well as desorption efficiencies were measured at different sampling parameters. The influence of air humidity on the adsorption behaviour was determined. Finally, the suitability of the system for outdoor air investigations was checked. The denuders were very suitable for the determination of aromatic hydrocarbons in workplace air; the general feasibility to investigate outdoor air samples was demonstrated.     

薄层扫描快速检测发酵液中琥珀酸

基于CuSO4与发酵液中琥珀酸的显色反应,在硅胶板上不经层析展开使用薄层扫描定量分析琥珀酸含量.在0～12 g/L范围内,测定波长680 nm,参比波长500 nm条件下,琥珀酸浓度与显色斑吸光度呈良好线性关系.方法检出限(3 S/k)为0.028 mg/L,回收率94.80％～96.12％,相对标准偏差≤3.5％(n...     

Chemiluminescence determination of ferulic acid by flow-injection analysis using cerium(IV) sensitized by rhodamine 6G

A simple, sensitive and rapid flow-injection chemiluminescence method has been developed for the determination of ferulic acid based on the chemiluminescence reaction of ferulic acid with rhodamine 6G and ceric sulfate in sulphuric acid medium. Strong chemiluminescence signal was observed when ferulic acid was injected into the acidic ceric sulfate solution in a flow-cell. The present method allowed the determination of ferulic acid in the concentration range of 8.0x10(-6) to 1.0x10(-4)moll(-1) and the detection limit for ferulic acid was 8.7x10(-9)moll(-1). The relative standard deviation was 2.4% for 10 replicate analyses of 1.0x10(-5)moll(-1) ferulic acid. The proposed method was applied to the determination of ferulic acid in Taita Beauty Essence samples with satisfactory results.     

Determination of uranium in phosphoric acid using neutron activation analysis

Phosphoric acid is generally obtained from an aqueous process starting with the reaction between phosphate rock and sulphuric acid. Due to their chemical similarity, uranium is usually associated with phosphate rock which during chemical processing is partitioned to phosphoric acid. Uranium determination in this matrix is a very important task because of its ingestion it could lead to radiological impact on the population. Therefore, a procedure was developed using an initial precipitation with calcium hydroxide and evaporation, followed by instrumental neutron activation analysis (INAA). The procedure was applied to analyse fourteen uranium enriched phosphoric acid samples.     

Wet effluent diffusion denuder technique and the determination of volatile organic compounds in air. II. Monoterpenes

In this work, a comparative study for the fractionation of Trichoderma reesei cellulases on five different hydrophobic interaction chromatography adsorbents (Butyl-Sepharose 4 FF, Phenyl-Sepharose 6 FF, Octyl-Sepharose 4 FF, Epoxy-Sepharose CL-6B and Polypropylene glycol-Sepharose CL-6B) is shown. The influence of the mobile phase composition on the chromatographic behaviour of T. reesei cellulases complex was evaluated using different concentrations of ammonium sulphate in the eluent buffer. A selective separation of beta-glucosidase with two-fold increase in specific activity and good recoveries of cellobiase activity were obtained with Butyl-Sepharose 4 FF and Phenyl-Sepharose 6 FF using 7% (w/v) ammonium sulphate in the eluent buffer. A beta-glucosidase fractionation was also obtained with Epoxy-Sepharose CL-6B, using 13% (w/v) of the salt in the mobile phase.     

Determination of sulphuric acid in process effluent streams using sequential injection titration

Sulphuric acid in process effluent streams from an electrorefining copper plant was analysed with a sequential injection (SI) titration system using sodium hydroxide as titrant. In the proposed SI titration system a base titrant, acid analyte and base titrant zone were injected sequentially into a distilled water carrier stream in a holding coil and swept by flow reversal through a reaction coil to the detector. The base zones contained bromothymol blue as indicator and the endpoint was monitored spectrophotometrically at 620 nm. The influence of carrier stream flow rate, acid and base zone volumes and titrant concentration on the linear range of the method was studied to obtain an optimum. A linear relationship between peak width and logarithm of the acid concentration was obtained in the range 0.006-0.178 mol l(-1) of H(2)SO(4) for a NaOH concentration of 0.002 mol l(-1). The results obtained for the SI titration of process samples were in good agreement with a standard potentiometric method with an RSD<0.75% and a sample frequency of 23 samples h(-1).     

流动注射化学发光法测定水中的苯酚

基于苯酚对鲁米诺 铁氰化钾化学发光体系有增敏作用 ,建立起测定苯酚的新方法。苯酚浓度在0 0 1～ 10mg L范围内与化学发光强度呈良好的线性关系 ,标准曲线为ΔI =30 7.44C(mg L) - 36 .92 9(n =9,r2 =0 .9983) ,检出限 (3σ)为 0 .0 0 4mg L ,对 1mg L的苯酚进行 11次平行测定 ,相对标准偏差 (RSD)为 1.0 6 %。本法已用于废水中苯酚的测定。     

鲁米诺-焦性没食子酸体系抑制化学发光法测定5-磺基水杨酸

基于碱性介质中5-磺基水杨酸对鲁米诺-焦性没食子酸体系化学发光的抑制作用,建立了流动注射化学发光测定5-磺基水杨酸的新方法.在最佳实验条件下,测定5-磺基水杨酸的线性范围为1.0×10-7～1.0×10-5mol/L,相关系数为0.9996(n=5),检出限为6.8×10-8mol/,L(n=11),对1.0×10-6...