Carbon nanotube assisted synthesis of CeO2 nanotubes

CeO₂ nanotubes have been synthesized facilely using carbon nanotubes (CNTs) as templates by a liquid phase deposition method. The properties of the CeO₂ nanotubes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectrum (XPS) as well as thermogravimetry and differential thermal analysis (TG-DTA). The obtained CeO₂ nanotubes with a polycrystalline face-centered cubic phase have a uniform diameter ranging from 40 to 50 nm. The CeO₂ nanotubes are composed of many tiny interconnected nanocrystallites of about 10 nm in size. The pretreatment of CNTs and calcination temperature were confirmed to be the crucial factors determining the formation of CeO₂ nanotubes. A possible formation mechanism has been suggested to explain the formation of CeO₂ nanotubes.     

纳米结构CuO为敏感电极的阻抗谱型NO2传感器

以浸渍技术制备的纳米CuO颗粒作敏感电极,以YSZ作为固体电解质制备了阻抗谱型NO2传感器。采用XRD、SEM对NO2传感器敏感材料的相组成和微观形貌进行了表征,应用电化学工作站测试了传感器的敏感性能。结果表明:浸渍法制得的CuO颗粒均匀分布在电解质的多孔层内,粒径在200 nm左右。在450～550℃,传感器对NO2有良好的敏感性,在0.1 Hz总阻抗|Z|=(Z′2+Z″2)～(1/2)姨与NO2浓度(0～200 mL.m-3)呈良好的线性关系。传感器的固有响应时间为50 s,共存的O2和CO2气体对传感器敏感性能几乎没有影响。     

硝酸镁在γ-Al2O3上的热分解及MgO/γ-Al2O3

研究了不同载量时Mg(NO     

Effect of conversion of NO2 into no on the catalytic reduction of NO2 with C3H6 in excess O2

During the reduction of NO₂ by C₃H₆ in O₂ over alumina-supported Au, Rh and Pt it was found that three parallel reactions take place,i.e., reduction of NO₂ to N₂ and N₂O, partial decomposition of NO₂ to NO and oxidation of C₃H₆ to CO and CO₂. In the absence of C₃H₆, the NO₂→NO+O₂ reaction reaches a fast equilibrium on Rh and Pt but not on Au and γ-Al₂O₃. Addition of C₃H₆ to the NO₂+O₂ mixture leads to the formation of NO above equilibrium conversion levels.     

TiO_2光催化失活复活特性与表面NO_3~-浓度的关系

以乙醛作为活性标的,通过人为控制表面附着NO3-浓度,检测TiO2对乙醛的吸附能力和光催化降解能力,得出了TiO2光催化失活复活特性和表面附着NO3-浓度的定量关系。结果表明,表面附着NO3-浓度达到4.24wt%时,光催化降解能力降低50%;表面附着NO3-浓度达到10.50wt%时,TiO2的吸附能力降低50%;通过溢流状态下水洗2h,可除去98%的表面附着NO3-,使TiO2光催化活性复活。     

Cu-Ni/La2O3热解C2H2制备碳纳米管的研究

Nano-sized and well-dispersed Cu-Ni/La₂O₃ can be obtained by reduction of LaCu_0.2Ni_0.8O₃ with the structure of perovskite. Using Cu-Ni/La₂O₃ as catalyst and C₂H₂ as carbon source, carbon nanotubes with a high yield and narrow diameter distribution can be obtained in the reaction temperature range of 650～700℃. Outer diameter of carbon nanotubes rangs from 9nm to 14nm. TG, Raman and XPS analysis indicate that carbon nanotubes prepared by Cu-Ni/La₂O₃ are relatively higher in graphitic degree.     

LB膜诱导Ba(NO3)2晶体取向生长

In this work, Ba(NO₃)₂ crystals with single crystal face were induced by using the the method of bio-mimetic mineralization and double LB films of behenic acid (BA) as the template. The crystals were characterized by Scanning Electron Microscope (SEM) and X-Ray Diffraction (XRD). The crystals were observed in regular square shape with uniform size about 5～8 μm by SEM, and they were found by XRD to grow along the (111) plane. From these experiments, we can conclude that the good selection of the (111) crystal face of Ba(NO₃)₂ is due to the electrostatic interactions , the match between this crystal face and the definite lattice structure of the LB films.     

NO2对Cu/SAPO-34分子筛催化剂上NH3选择性催化还原NO性能的影响

主要考察了NO₂对Cu/SAPO-34 分子筛催化剂在整个温度范围内（100-500 ℃）NH₃选择性催化还原（SCR）NO性能的影响. 研究所使用样品为新鲜Cu/SAPO-34 催化剂在750 ℃下水热处理4 h 的稳定期样品.通过X射线衍射（XRD）和扫描电子显微镜（SEM）对样品的结构以及形貌进行表征,采用SCR活性评价、动力学实验以及原位漫反射傅里叶变换红外光谱（in situ-DRIFTS）表征催化剂的性能以及催化剂表面物种的变化. 活性评价实验结果表明,NO₂会抑制催化剂的低温（100-280 ℃）活性,但其存在会提高催化剂的高温（280 ℃以上）活性. 与此同时,随着反应物中NO/NO₂的摩尔比例减少,由于NH₄NO₃物种的分解,副产物（N₂2O）的浓度增大. 动力学结果表明,Cu/SAPO-34 催化剂上快速SCR反应的表观活化能（E_a=64.02 kJ·mol^-1）比标准SCR反应的表观活化能（E_a=48.00 kJ·mol^-1）更大. In situ-DRIFTS实验结果表明NO比NO₂更容易在催化剂表面形成硝酸盐,并且NO₂更容易与吸附在Brønsted 酸性位上的NH₃物种反应生成NH₄NO₃. 低温下,催化剂表面的NH₄NO₃物种会覆盖SCR反应的活性位,造成活性降低,但在高温时,形成的NH₄NO₃物种一部分会被NO还原为N2,而另一部分会直接热分解为N₂O,造成催化剂的选择性降低.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

Carbon coated Na3V2(PO4)3 as novel electrode material for sodium ion batteries

A Na₃V₂(PO₄)₃ sample coated uniformly with a layer of 6 nm carbon has been successfully synthesized by a one-step solid state reaction. This material shows two flat voltage plateaus at 3.4 V vs. Na⁺/Na and 1.63 V vs. Na⁺/Na in a nonaqueous sodium cell. When the Na₃V₂(PO₄)₃/C sample is tested as a cathode in a voltage range of 2.7-3.8 V vs. Na⁺/Na, its initial charge and discharge capacities are 98.6 and 93 mAh/g. The capacity retention of 99% can be achieved after 10 cycles. The electrode shows good cycle performance and moderate rate performance. When it is tested as an anode in a voltage range of 1.0-3.0 V vs. Na⁺/Na, the initial reversible capacity is 66.3 mAh/g and the capacity of 59 mAh/g can be maintained after 50 cycles. These preliminary results indicate that Na₃V₂(PO₄)₃/C is a new promising material for sodium ion batteries.     

High activity of novel Pd/TiO2 nanotube catalysts for methanol electro-oxidation

Electro-oxidation of methanol in sulfuric acid solution was studied using palladium well-dispersed on titanium nanotubes, in relation to methanol oxidation processes in the direct oxidation methanol fuel cell. Pd dispersed on titania nanotubes, which leads to high surface area substrates, showed excellent catalytic activities compared to those of pure Pd and Pd-TiO₂ nanoparticles. TEM results show a narrow distribution of TiO₂ nanoparticles whose particle size is about 10 nm, and uniform nano-sized TiO₂ nanotubes with 10 nm in diameters are seen from HRTEM . A homogeneous structure in the composite nanomaterials is indicated by XRD analysis. The composite electrode activities were measured by cyclic voltammetry (CV) and at 25 °C it was found that 3 wt% Pd in titania nanotubes had the best activity for methanol oxidation.     

Determination of thermodynamic properties of aqueous mixtures of MgCl2 and Mg(NO3)2 by the potentiometric method at T = 298.15

In this research, thermodynamic properties of the ternary electrolyte system (MgCl₂ + Mg(NO₃)₂ + H₂O) were investigated using a potentiometric method. The galvanic cell used had no liquid junction of type: Mg-ISE|MgCl₂ (m_A), Mg(NO₃)₂ (m_B), H₂O|Ag/AgCl. The measurements were performed at T = 298.15 K and at total ionic strengths from 0.001 to 8.000 mol/kg for different series of salt ratios r=mMgCl₂/mMg₂(NO₃) =1.00, 2.50, 5.00, 7.50, 10.00 and 15.00. The PVC based magnesium ion-selective electrode (Mg-ISE) and the Ag/AgCl electrode used in this work were prepared in our laboratory and showed a reasonably good Nernst response. The Pitzer ion interaction model and Harned rule were used to illustrate the ternary electrolyte system investigated. The experimental results showed that both Pitzer model and Harned rule were suitable to be used satisfactorily to describe this ternary system.     

碳纳米管负载的Fe2O3催化剂制备

Carbon nanotubes were modified by FeSO₄-H₂O₂ system, iron hydroxides were adsorbed on the wall of carbon nanotubes simultaneously. These precursors were treated at 723K for 2 h under hydrogen, nitrogen and air atmosphere to prepare carbon nanotubes supported γ-Fe₂O₃catalyst, γ-Fe₂O₃and α-Fe₂O₃compound catalyst and amorphous Fe₂O₃catalyst, respectively. This is green method to prepare high Fe₂O₃loading (≥50 %) catalyst without adding other cation. The different structures Fe₂O₃catalysts can be synthesized by controlling the condition of thermal treatment to content active phase requirements for different catalytic reactions. The paper presents a new method to prepare carbon nanotubes supported catalysts.     

Prussian Blue electrodeposited on MWNTs-PANI hybrid composites for H2O2 detection

A Prussian Blue (PB)/polyaniline (PANI)/multi-walled carbon nanotubes (MWNTs) composite film was fabricated by step-by-step electrodeposition on glassy carbon electrode (GCE). The electrode prepared exhibits enhanced electrocatalytic behavior and good stability for detection of H₂O₂ at an applied potential of 0.0 V. The effects of MWNTs thickness, electrodeposition time of PANI and rotating rate on the current response of the composite modified electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. A linear range from 8 × 10⁻⁹ to 5 × 10⁻⁶ M for H₂O₂ detection has been observed at the PB/PANI/MWNTs modified GCE with a correlation coefficient of 0.997. The detection limit is 5 × 10⁻⁹ M on signal-to-noise ratio of 3. To the best of our knowledge, this is the lowest detection limit for H₂O₂ detection. The electrode also shows high sensitivity (526.43 μA μM⁻¹ cm⁻²) for H₂O₂ detection which is more than three orders of magnitude higher than the reported.     

TiO2 nanorods branched on fast-synthesized large clearance TiO2 nanotube arrays for dye-sensitized solar cells

A large clearance TiO₂ nanotube arrays (LTAs) has been synthesized by a not more than 12 h anodization duration and based on this a branched TiO₂ nanotube arrays (BLTs) has been achieved through TiO₂ nanorods branch-like grown on the LTAs. Some key factors and probable mechanisms of the fabrication processes on two novel nanoarchitectures are discussed. Exhilaratingly, it is found that the obtained LTAs has demonstrated large pore diameter and void spaces (pore diameter ∼350 nm; void spaces ∼160 nm; and tube length ∼3.5 μm), and the synthesized hierarchical BLTs, compared with conventional TiO₂ nanotube arrays, has shown a much stronger dye absorption performance and an approximately double of the solar cell efficiency (in our case from 1.62% to 3.18% under simulated AM 1.5 conditions).     

四元体系LiNO3-Mg(NO3)2-NH4NO3-H2O相图预测及相关相变储能材料的研究

应用修正的BET热力学模型对Mg(NO3)2-NH4NO3-H2O三元体系和LiNO3-Mg(NO3)2-NH4NO3-H2O四元体系在273～320 K的相图进行预测,并找到一个相变温度较低的四元共晶点Mg(NO3)2.6H2O-LiNO3.3H2O-NH4NO3,其质量百分数组成为:25.5%的硝酸铵,28.4%的硝酸锂,13.8%的硝酸镁和32.3%的水,通过实验对共晶点组成材料的吸放热行为进行测定,发现其熔化温度为286.3 K,且DSC测试其相变热焓为192.7 J.g-1,表明该材料可用作潜在的低温相变储能材料。     

A parametric study of CO2/N2 gas separation membrane processes for post-combustion capture

Capture of CO₂ from flue gases produced by the combustion of fossil fuels and biomass in air is referred to as post-combustion capture. Chemisorbent processes are considered to be the most feasible method and are already at an advanced stage of development, but gas separation membranes are attracting more and more attention as a possible alternative. This paper describes a detailed parametric study of mass and energy balances for a simulated single membrane process. Typical operating conditions (CO₂ concentration in the flue gas, pressure and temperature, etc.) together with the influence of the membrane quality (permeability, selectivity) and membrane area on membrane performance (CO₂ separation degree and CO₂ purity) are simulated over a wide range of parameters.     

Catalytic oxidation of no to NO2 over Cr/TiO2 and Cu/TiO2 under oxidizing atmosphere

The catalytic activity of Cr/TiO₂ and Cu/TiO₂ for the oxidation of NO under an oxidizing atmosphere has been examined. Both catalysts had excellent ability for the oxidation of NO to NO₂ in the temperature range of 350–400°C.     

Ho(NO3)3(C2H5O2N)4·H2O的低温热容和热力学函数

合成了稀土(钬, Ho)-氨基酸(甘氨酸, C₂H₅O₂N)二元配合物Ho(NO₃)₃(C₂H₅O₂N)₄·H₂O, 并且通过化学分析、元素分析和红外(IR)光谱对配合物进行了表征. 用高精度全自动绝热量热仪, 测定了该配合物在80-390 K温度区间的定压摩尔热容(C_p,m). 利用实验测定的热容数据, 采用最小二乘法, 将热容曲线上热容峰以外的两段平滑区的摩尔热容对折合温度进行拟合, 建立了热容随折合温度变化的多项式方程. 根据热容与焓、熵的热力学关系,计算出了配合物在80-390 K温度区间内,每隔5 K,相对于298.15 K的摩尔热力学函数(H_T,m-H_298.15,m)和(S_T,m-S_298.15,m). 通过热容曲线分析, 计算出了350 K附近转变过程的焓变(Δ_trsH_m)和熵变(Δ_trsS_m). 用差示扫描量热法(DSC)测定了配合物的热稳定性.     

Cr2O3-modified ZnO thick film resistors as LPG sensors

Thick films of pure ZnO were obtained by screen-printing technique. Surface functionalized ZnO thick films by Cr₂O₃ were obtained by dipping pure ZnO thick films into 0.01 M aqueous solution of chromium trioxide (CrO₃). The dipped films were fired at 500 °C for 30 min. Upon firing, the CrO₃ would reduce to Cr₂O₃. Cr₂O₃-activated (0.47 mass%) ZnO thick films resulted in LPG sensor. Upon exposure to 100 ppm LPG, the barrier height between Cr₂O₃ and ZnO grains decreases markedly, leading to a drastic decrease in resistance. The sensor was found to sense LPG at 350 °C and no cross sensitivity was observed to other hazardous, polluting and inflammable gases. The quick response (∼18 s) and fast recovery (∼42 s) are the main features of this sensor. The effects of microstructures and dopant concentrations on the gas sensing performance of the sensor were studied and discussed.