水性聚氨酯/纳米TiO2复合乳液制备及其抗菌性能的研究

以佛尔酮二异氰酸酯(IPDI)、聚丙二醇(PPG)和改性纳米TiO2为主要原料,二羟甲基丙酸(DMPA)为亲水扩链剂和乙二胺(EDA)为小分子扩链剂,通过原位分散聚合方法制备了水性聚氨酯/纳米TiO2复合乳液。考察了改性纳米TiO2用量对复合乳液粘度、粒径及稳定性的影响。结果表明,复合乳液具有一定的紫外吸收能力和良好的抑菌作用,抑菌性能随纳米TiO2含量的增加而提高。     

生物基水性聚氨酯的制备及性能研究

以甲苯二异氰酸酯(TDI)和二羟甲基丙酸(DMPA)为硬段,丙烯酸松香GMA二元醇(RAG)和聚乙二醇(PEG-1000)为软段,通过预聚体法合成了松香基芳香族型水性聚氨酯(RWPU).利用红外光谱、X射线衍射分析、热重分析、差示扫描量热分析、静态水接触角等分别表征了RWPU的组成、结构、热性能和耐水性,研究了不同R值...     

聚硅氧烷与纳米SiO_2复合改性光固化水性聚氨酯的制备与性能

以聚碳酸酯二元醇(PCD)和羟基封端的聚二甲基硅氧烷(PDMS)为软段、异佛尔酮二异氰酸酯(IPDI)为硬段,在乳化过程中引入纳米SiO_2,制得光固化水性聚氨酯纳米复合乳液。采用纳米粒度仪、SEM、光学接触角测量仪、电子拉力机等对复合乳液和复合膜的结构与性能进行了表征。研究结果表明:纳米SiO_2相互接触,形成了连续的纳米SiO_2网状结构贯穿于整个聚合物基体中;PDMS与纳米SiO_2的复合引入使复合膜杨氏模量、拉伸强度、断裂伸长率、表面疏水性及耐水性均得到显著提高。     

四甲基苯二甲基二异氰酸酯基水性聚氨酯的合成和性能

采用四甲基苯二甲基二异氰酸酯、聚酯二元醇和二羟甲基丙酸为原料,合成了一系列具有不同异氰酸根与羟基摩尔比（n(-NCO)/n(-OH)）的聚氨酯乳液。 研究了n(-NCO)/n(-OH)对水性聚氨酯性能的影响。 结果表明,当该比值增加时,乳液的粒径增大,分布变宽,结晶性降低,耐热性下降,耐水性能呈现降低的趋势。 当异氰酸根与羟基摩尔比为3时,四甲基苯二甲基二异氰酸酯基水性聚氨酯的乳液粒径为10～30 nm,膜的分解温度达到275 ℃,24 h吸水率低于10%。     

磷酸盐聚酯型水性聚氨酯/纳米SiO2的合成与性能

以2-磷酸基-1,2,4-三羧酸丁烷(PBTCA)、新戊二醇(NPG)为原料,制得数均相对分子质量为1500并含有磷酸基团的聚酯多元醇。将其与异佛尔酮二异氰酸酯(IPDI)反应,经1,4-丁二醇(BDO)扩链后得到水性聚氨酯,再以KH550为偶联剂,加入纳米SiO2,合成了纳米改性的磷酸型水性聚氨酯(PWPU)。通过红外光谱(FI-IR)、热重分析(TGA)对PWPU的结构和热稳定性进行了研究,使用透射电子显微镜(TEM)对乳液的形貌进行了观察。通过TEM发现,大量粒径在110 nm左右的化合物合成,并与红外光谱联合分析得出,SiO2通过化学键与PWPU相连接。热重分析、残炭量分析和拉伸测试表明,经过纳米SiO2改性的PWPU其阻燃性、热稳定性以及力学性能均有明显的提升,具有很好的应用前景。     

水性聚氨酯的制备及其性能的研究

本文以琥珀酸酐与三羟甲基丙烷反应,制得了含有羟基和羧基的酯类亲水性单体,并以此单体与ＴＤＩ和ＰＰＧ－１０００反应,制得了含有羧基的聚氨酯预聚体,在三乙醇胺水溶液中分散得到了水性聚氨酯（简称ＷＰＵ）。本文对预聚体的溶剂种类和用量,对乳胶粒的大小及形状的影响进行了研究,确认溶剂的用量越大,乳胶的粒径就越小;以丙酮作溶剂,乳胶粒为棒状或橄榄球状,而以丁酮为溶剂,得到的乳胶粒为圆球状。通过改变亲水单体的用     

纳米氧化锡锑改性水性聚氨酯的制备与表征

以异佛尔酮二异氰酸酯(IPDI)、聚醚二醇（N-210）、二羟甲基丙酸（DMPA）、一缩二乙二醇（DEG）、三羟甲基丙烷（TMP）及纳米氧化锡锑（ATO）浆料为主要原料,制备了稳定的纳米ATO改性水性聚氨酯(APU)乳液。 粒径测试及透射电子显微镜（TEM）观察显示,纳米ATO在水性聚氨酯中分散较好,乳液粒径均小于100 nm; FTIR分析表明,纳米ATO粒子与水性聚氨酯(WPU)间可能存在化学键; 热重分析(TGA)测试显示,随纳米ATO添加量的增加,胶膜最大热分解温度逐渐提高,最大提高了约20 ℃;紫外-可见-近红外吸收及保温性能测试表明,随着纳米ATO添加量的提高,胶膜在800~2500 nm的透过率逐渐降低,但涂层在可见光区透过率均超过70%,热阻率由1.34×10-2 m2·℃/W提高至3.17×10-2 m2·℃/W。     

纳米SiO2含量对水性聚氨酯复合材料性能的影响

纳米SiO2;水性聚氨酯;原位聚合;形态;性能     

水性聚氨酯阻燃纳米复合材料的Click反应制备及性能

以4,4'-二羟甲基-1,4-庚二炔功能单体作为扩链剂制备了端炔基功能化聚氨酯, 与叠氮基改性纳米蒙脱土(MMT-N₃)、 纳米氢氧化铝(ATH-N₃)和纳米氢氧化镁(MH-N₃)通过Click反应制备了水性聚氨酯(WPU)阻燃纳米复合材料. 采用红外光谱(FTIR)、 核磁氢谱(¹H NMR)和扫描电子显微镜(SEM)对WPU阻燃纳米复合材料的结构进行了表征, 对比研究了纳米阻燃剂配比和制备方法对WPU阻燃纳米复合材料的氧指数、 动态燃烧行为和热稳定性的影响. 阻燃性能研究结果表明, 当MMT-N₃, MH-N₃和ATH-N₃的质量分数分别为7%, 2%和1%时, 采用Click反应制备的复合材料的氧指数比纯WPU高7%, 点燃时间从10 s延长到29 s, 峰值热释放速率和烟释放速率分别降低了41%和42%. 热失重分析结果表明, 当MMT-N₃质量分数为10%时, 与WPU相比, 采用Click反应制备的MMT/WPU复合材料在热失重50%时的温度提高了21 ℃. 复合材料断面和燃烧后残渣的SEM分析证明在聚合物基体中Click反应是分散纳米材料的一种有效方法.     

水性聚氨酯胶粘剂结构与性能的研究

以聚醚烽异氟尔酮二异氰酸酯为主要原料,以二羟甲基酸为亲水单体制备了一组不同配方组成的聚氨酯乳胶粘剂。通过粘度测定、粒度分析、力度性能的测试以及DSC分析,研究了新水剂含量、软链段的类型和加料方法对乳液及其胶膜性能的影响。结果表明：二羟甲基丙酸含量在3％－8％之间可获得比较稳定的乳液,并且两步法较一步法制得的乳液分散性好,但胶膜力学性能方面,一步法较好。     

Physicochemical and antibacterial properties of polyurethane coatings modified by ZnO

The synthesis of polyurethane nanocomposite coatings containing 1% to 5% suitably dispersed ZnO by 1‐stage polyaddition process in the bulk using 4,4′‐methylenebis(cyclohexyl isocyanate), poly(ε‐caprolactone)diol, and 1,4‐butanediol was performed. Infrared and nuclear magnetic resonance spectra confirmed the structure of obtained polyurethanes. Scanning electron microscope and energy dispersive X‐ray analyzer methods showed randomly distributed ZnO in a polyurethane matrix. The differential scanning calorimetry and wide‐angle X‐ray diffraction patterns were used for the microstructural assessment of the obtained materials. Antimicrobial properties of ZnO and the effect of this modifier on the hydrophobicity of the coatings were demonstrated. The obtained coatings were characterized in terms of the mechanical properties and changes during incubation in a Baxter saline solution.     

Imidazole derivatives as the organic precursor of ZnO nano particle

N₁-Hydroxy-2,4,5-trisubstituted imidazoles were synthesized starting from 1,2-diketones. The crystal structure of 4,5-dimethyl-2-(3-nitrophenyl)-1H-imidazol-1-ol has been determined. An unusual intermolecular hydrogen bonding through the association of water molecule has been reported. These imidazole derivatives can be thought of as the organic precursor for the synthesis of zinc oxide nano particles.     

Design and synthesis of polyindole - ZnO nano composite for NLO applications

Present paper mainly focuses on the synthesis, characterization polyindole-ZnO nano composites for third order nonlinear optical applications. Polyindole was synthesized through oxidative polymerization technique and its composites were prepared with different ZnO concentration. Structural morphology of the polymer composite was studied using FESEM, XRD and UV Visible spectroscopic technique. Polymer showed broad absorption with absorption maxima of 395 nm. Newly prepared thin films showed excellent nonlinear absorption with very good optical limiting behaviour when it is exposed to He-Ne laser with maximum optical limiting power of 11 mW along with third-order nonlinear susceptibility χ⁽³⁾ of 2.72 × 10^?3 esu. Hence these polymer composites may be potential candidate for optical limiting applications.     

Synthesis and surface properties of polyurethane modified by polysiloxane

A series of polyurethanes modified by polysiloxane (Si-PU) were synthesized based on 2,4-toluene diisocyanate (TDI), dihydroxybutyl-terminated polydimethylsiloxane (DHPDMS), polytetramethylene glycol (PTMG) and 1,4-butanediol (BDO). Fourier transform infrared spectroscopy analysis showed that DHPDMS had been incorporated into the polyurethane chains. With the increase of DHPDMS content, the water contact angle increased while the surface tension decreased. As the DHPDMS content increases above 5%, both the contact angle and the surface tension tend to approach a constant. The contact angle increases with increasing temperature, and it tends to approach a constant when the temperature is higher than 50°C. The result indicates that Si-PU exhibits good surface and mechanical properties when the DHPDMS content is 5%. __________ Translated from Polymer Materials Science and Engineering, 2007, 23(3): 47–50 [译自: 高分子科学与工程]     

Effects of nano ZnO on strength and stability of unsaturated polyester composites

ZnO–glass fiber–unsaturated polyester composites have been prepared. On exposure to the metal halide lamp, their resistance to ultraviolet (UV) degradation is evaluated. Experimental results show that ZnO can reduce the UV degradation of the unsaturated polyester matrix. ZnO can significantly retard the UV degradation process of the matrix resin, and can also increase the impact strength of the composites under the experimental conditions. Differential scanning calorimetry (DSC) analyses also indicate that the addition of ZnO to unsaturated polyester may retard the crosslink process and catalyze the decomposition of the resin. However, after more than 40 hr of UV irradiation, it was crosslinked. SEM fracture morphology shows that nano ZnO could hinder crack growth and induce more cracks, and when the content of ZnO reaches 6 wt%, the impact fracture mechanism changes abruptly and plastic deformation appears, which indicates that 6 wt% for ZnO in unsaturated polyester could be considered as the critical content. Around the critical content, the particles are near enough to interact with each other and this results in the change of fracture mechanism. The results also indicate that the proper content of ZnO added into an unsaturated polyester could prolong the durability and lessen the reject rate of transparent glass fiber–polyester composites. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation of thermosetting polyurethane nanocomposites by montmorillonite modified with a novel intercalation agent

A novel thermosetting polyurethane (TSPU)/organic montmorillonite (OMMT) nanocomposite has been synthesized. N‐diamino octadecyl trimethyl ammonium chloride (DODTMAC) was used as an intercalation agent to treat Na⁺‐montmorillonite (MMT) and form a novel kind of OMMT. Fourier transform infrared spectroscopy (FT‐IR), wide angle X‐ray diffraction (WAXD), and thermogravimetric analysis (TGA) data indicated that the MMT was successfully intercalated by this intercalation agent, as evidenced by the fact that the basal spacing of MMT galleries was expanded from 1.5 to 3.2 nm. This OMMT was used to prepare the TSPU nanocomposites. Both the reinforcing and compatibilizing performance of the filler were investigated. Tensile tests showed that the tensile strength of TSPU/OMMT‐4 was the highest, and was about 3.62 times higher than that of the pure TSPU, and also the elongation at break showed an enhancement. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) measurements illustrated that the glass transition temperature of the TSPU/OMMT‐4 nanocomposite was improved from 0.5 to 6.5 °C, which corresponded to the restriction of the soft segments of TSPU. The highest initial and center temperatures of TSPU/OMMT‐4 obtained from TGA were due to the highest retard effect of the TSPU molecular chains. WAXD studies showed that the formation of the nanocomposites in all the cases with the almost disappearance of the peaks corresponding to the basal spacing of MMT. SEM and TEM were used to investigate the morphologies of the TSPU/OMMT‐4 nanocomposite, and demonstrated that the nanocomposite was comprised of a well dispersion of a mixture of intercalated and exfoliated silicate layers throughout the matrix. It was proposed that the nano‐reinforcing effect caused by the well‐dispersed silicate layers might reduce the amount and size of voids and increase the length of the crack‐spreading path during tensile drawing. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 519–531, 2007.     

乙二醇表面改性纳米二氧化钛的制备及其对水性聚氨酯的改性

以乙二醇(EG)和钛酸四丁酯(TBOT)为原料,采用原位表面修饰方法成功制备了乙二醇表面改性纳米TiO2(EG-TiO2);利用傅立叶红外光谱仪、X射线衍射仪、透射电子显微镜表征了其结构,采用热重分析仪测定了其热稳定性.结果表明,经表面修饰的纳米二氧化钛在水性聚氨酯皮革涂饰剂(WPU)基体中分散良好;将EG-TiO2添加到WPU中能显著提高其抗紫外线性能、热稳定性及耐磨性能.     

Effects of flower-like ZnO nanowhiskers on the mechanical, thermal and antibacterial properties of waterborne polyurethane

A novel waterborne polyurethane/flower-like ZnO nanowhiskers (WPU/f-ZnO) composite with different f-ZnO content (0-4.0 wt%) was synthesized by an in-situ copolymerization process. The f-ZnO consisting of uniform nanorods was prepared via a simple hydrothermal method. In order to disperse and incorporate f-ZnO into WPU matrix, f-ZnO was modified with γ-aminopropyltriethoxysilane. Morphology of f-ZnO in WPU matrix was characterized by scanning electron microscope. The properties of WPU/f-ZnO composites such as mechanical strength, thermal stability as well as water swelling were strongly influenced by the f-ZnO contents. It was demonstrated that appropriate amount of f-ZnO with good dispersion in the WPU matrix significantly improved the performance of the composites. The mechanical property was enhanced with an increase of f-ZnO content up to the optimum content (1 wt%) and then declined. Incorporation of f-ZnO enhanced the water resistance of the composites remarkably. It was amazing to observe that the thermal degradation temperatures of the composites initially decreased significantly and then leveled off with content increase of f-ZnO, which was different from the results of other WPU composite systems reported. Antibacterial activity of WPU/f-ZnO composite films against Escherichia coli and Staphylococcus aureus was also tested. The results revealed that the antibacterial activity enhanced with the increasing f-ZnO content, and the best antibacterial activity was obtained at the loading level of 4.0 wt% f-ZnO.     

微/纳米ZnO粉体在Glu-BF_4离子液体水溶液中的诱导生长

以一定浓度谷氨酸-氟硼酸(Glu-BF_4)离子液体水溶液为反应介质,摩尔比为1∶6的二水合醋酸锌和氢氧化钠为反应物,在室温下制备前驱体,再通过微波辅助加热制备了具有绒球形貌的微/纳米ZnO粉体.利用扫描电子显微镜(SEM)、X射线衍射仪、比表面积测试仪、能谱仪、拉曼光谱仪和透射电子显微镜(TEM)等对产物形貌、晶型、比表面积、组成和晶面分布进行了测定.结果显示,所得产物为六方晶系纤锌矿结构,平均粒径20.4 nm,绒球大小1.6~3.0μm,比表面积为28.3 m~2/g,产物纯度较高.当反应物浓度一定,离子液体浓度分别为0.02,0.04,0.08和0.12 mol/L时都得到了类似形貌的微/纳米ZnO粉体,且随着离子液体使用量的增加,绒球尺寸分布更加均一.当离子液体浓度一定,而反应物浓度逐渐下降时,产物形貌发生递变性变化.ZnO晶粒在Glu-BF_4离子液体诱导下首先生成不规则的纳米片,纳米片进一步聚集,在一定反应物浓度范围内生成绒球形貌粉体,反应物浓度较低时只生成绒球的核心部分,而浓度更高时则生成纳米针阵列.通过不同条件下纳米ZnO粉体形貌变化规律,探讨了强碱性条件下Glu-BF_4离子液体水溶液中微/纳米ZnO粉体的生长机制.     

Synthesis, characterization and properties of a novel fluorinated polyurethane

A novel fluorinated polyurethane (FPU) was prepared by fluorinated polyether glycol (PTMG-g-HFP) as a soft segment, 1,6-hexamethylene diisocyanate (HDI) or toluene diisocyanate (TDI) as a hard segment and 1,4-butanodiol (BDO) as a chain extender. Fourier transform infrared spectroscopy (FTIR), ¹H NMR, ¹³C NMR and gel permeation chromatography (GPC) were used to characterize the structure of the fluorinated polyurethane. The thermal stabilities of the fluorinated polyurethane and the corresponding hydrogenated polyurethane were studied by thermogravimetric analysis (TGA). X-ray photoelectron spectroscopy (XPS) analysis at two different sampling depths for the fluorinated polyurethane was used to investigate the surface compositions of FPU. And the mechanical properties of the fluorinated polyurethane and the corresponding hydrogenated polyurethane were also measured. Chemical resistance of polyurethane films was estimated through spot tests with different solvents. The results showed that FPU had high thermal stability, strain-hardening property and good chemical resistance. The XPS measurements showed the fluorine enrichment on the surface of FPU.