A novel method for preparing lithium manganese oxide nanorods from nanorod precursor

Lithium manganese oxide nanorods were prepared from manganese dioxide nanorods precursor. The structure and morphology were confirmed by X-ray diffraction (XRD) and transmission electron microscope (TEM). The data of the Rietveld refinement indicate that the nanorods preferentially grow along the [111] direction. After charge–discharge test at 1.0 mA cm⁻² in 3.0–4.4 V, the nanorods LiMn₂O₄ showed the 134.5 mAh g⁻¹ initial discharge capacity and only lost 1.1% of initial capacity after 30 cycles, which is better than that of bulk particles LiMn₂O₄ prepared by traditional solid-state reaction method. This effective and simple route to synthesis nanorods LiMn₂O₄ from one-dimensional (1D) precursor could also be extended to prepare 1D other nanomaterials with special electrochemical properties.     

Influence of carbon additive on the properties of spherical Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> and LiFePO<Subscript>4</Subscript> materials for lithium-ion batteries

Preparing spherical particles with carbon additive is considered as one effective way to improve both high rate performance and tap density of Li₄Ti₅O₁₂ and LiFePO₄ materials. Spherical Li₄Ti₅O₁₂/C and LiFePO₄/C composites are prepared by spray-drying–solid-state reaction method and controlled crystallization–carbothermal reduction method, respectively. The X-ray diffraction characterization, scanning electron microscope, Brunauer–Emmett–Teller, alternating current impedance analyzing, tap density testing, and electrochemical property measurements are investigated. After hybridizing carbon with a proper quantity, the crystal grain size of active materials is remarkably decreased and the electrochemical properties are obviously improved. The Li₄Ti₅O₁₂/C and LiFePO₄/C composites prepared in this work are spherical. The tap density and the specific surface area are as high as 1.71 g cm⁻³ and 8.26 m² g⁻¹ for spherical Li₄Ti₅O₁₂/C, which are 1.35 g cm⁻³ and 18.86 m² g⁻¹ for spherical LiFePO₄/C powders. Between 1.0 and 3.0 V versus Li, the reversible specific capacity of the Li₄Ti₅O₁₂/C is more than 150 mAh g⁻¹ at 1.0-C rate. Between 2.5 and 4.2 V versus Li, the reversible capacity of the LiFePO₄/C is close to 140 mAh g⁻¹ at 1.0-C rate.     

Preparation and characterization of spherical La-doped Li4Ti5O12 anode material for lithium ion batteries

The lithium secondary batteries with high power density need the electrode materials with both high specific capacity and high tap density. An “outer gel” method by TiCl₄ as the raw material has been developed to prepare spherical precursor. High tap density spherical Li₄Ti₅O₁₂ is synthesized by sintering the mixture of precursor and Li₂CO₃. La-doped Li₄Ti₅O₁₂ is also prepared by this method. X-ray diffraction, scanning electron microscopy, energy-dispersive spectrometry, tap density testing, and the determination of the electrochemical properties show that the Li₄Ti₅O₁₂ powders prepared by this method are spherical and exhibits high tap density. La³⁺ dopant improved the electrochemical performance over the pristine Li₄Ti₅O₁₂. It is tested that the tap density of the pristine and La³⁺-doped products is as high as 1.80 and 1.78 g•cm⁻³, respectively. Between 1.0 and 3.0 V versus Li, the initial discharge capacity of the La³⁺ dopant is as high as 161.5 mAh•g⁻¹ at 0.1C rate. After 50 cycles, the reversible capacity is still 135.4 mAh•g⁻¹.     

Preparation and characterization of spinel Li4Ti5O12 nanoparticles anode materials for lithium ion battery

Spinel Li₄Ti₅O₁₂ nanoparticles were prepared via a high-temperature solid-state reaction by adding the prepared cellulose to an aqueous dispersion of lithium salts and titanium dioxide. The precursors of Li₄Ti₅O₁₂ were characterized by thermogravimetry and differential scanning calorimetry. The obtained Li₄Ti₅O₁₂ nanoparticles were characterized using X-ray diffraction, transmission electron microscopy (TEM) and electrochemical measurements. The TEM revealed that the Li₄Ti₅O₁₂ prepared with cellulose is composed of nanoparticles with an average particle diameter of 20–30 nm. Galvanostatic battery testing showed that nano-sized Li₄Ti₅O₁₂ exhibit better electrochemical properties than submicro-sized Li₄Ti₅O₁₂ do especially at high current rates, which can deliver a reversible discharge capacity of 131 mAh g⁻¹ at the rate of 10 C, whereas that of the submicro-sized sample decreases to 25 mAh g⁻¹ at the same rate (10 C). Its reversible capacity is maintained at ~172.2 mAh g⁻¹ with the voltage range 1.0–3.0 V (vs. Li) at the current rate of 0.5 C for over 80 cycles.     

A carbon–LiFePO<Subscript>4</Subscript> nanocomposite as high-performance cathode material for lithium-ion batteries

A cathode material of an electrically conducting carbon–LiFePO₄ nanocomposite is synthesized by wet ball milling and spray drying of precursor powders prior to a solid-state reaction. The structural characterization shows that the composite is composed of LiFePO₄ crystals and 4.8 wt.% amorphous carbon. Galvanostatic charge/discharge measurements indicate that the composite exhibits a superior high energy and high cycling stability. This composite delivers a discharge capacity of 159.1 mAh g⁻¹ at 0.1 C, 150.8 mAh g⁻¹ at 1 C, and 140.1 mAh g⁻¹ at 2 C rate. The capacity retention of 99% is achieved after 200 cycles at 2 C. The 18,650 cylindrical batteries are assembled using the composite as cathode materials and demonstrate the capacity of 1,400 mAh and the capacity retention of 97% after 100 cycles at 1 C. These results reveal that the as-prepared LiFePO₄–carbon composite is one of the promising cathode materials for high-performance, advanced lithium-ion batteries directed to the hybrid electric vehicle and pure electric vehicle markets.     

Enhancement of the electrochemical performance of silicon/carbon composite material for lithium ion batteries

The silicon/carbon (Si/C) composite material was prepared, and the electrochemical performance was investigated as a promising anode material for lithium ion batteries. The results show that the binder in the electrode acts as an important role for improving the reversible capacity of the Si/C materials during cycling. The Si/C electrode with CMC/SBR binder possesses a better cycle performance than that with PVDF binder. The Si/C composite material shows an initial reversible capacity of more than 700 mAh∙g⁻¹ and remains a reversible capacity of 597 mAh g⁻¹ after 40 cycles.     

Preparation of TiO2-coated LiMn2O4 by carrier transfer method

The TiO₂-coated LiMn₂O₄ has been prepared by a carrier transfer method and investigated. This novel synthetic method involved the transfer of TiO₂ into the surface of LiMn₂O₄ with Vulcan XC-72 active carbon powders as a dispersant. The X-ray diffraction shows that spinel structure of materials does not change after the coating of TiO₂. The electrochemical performance tests show that the initial discharge capacity of TiO₂-modified LiMn₂O₄ is 111.5 mA h g⁻¹, which is better than that of pristine LiMn₂O₄ (103.8 mA h g⁻¹). The cyclic performance is significantly improved after surface modification. The TiO₂-modified LiMn₂O₄ by a carrier transfer method exhibits better discharge capability and lower resistance.     

Preparation, characterization and electrochemical performance of γ-MnO2 and LiMn2O4 as cathodes for lithium batteries

The spinel LiMn₂O₄ is a very promising cathode material with economical and environmental advantages. LiMn₂O₄ materials have been synthesized by solid state method using γ-MnO₂ as manganese source, and Li₂CO₃ or LiNO₃ as Li sources. γ-MnO₂ is a commercial battery grade electrolytic manganese dioxide (TOSOH-Hellas GH-S) and LiMn₂O₄ samples were synthesized at a calcinations temperature up to 800 °C. γ-MnO₂ and LiMn₂O₄ samples were characterized by X-ray diffraction, thermal and electrochemical measurements. X-ray powder diffraction of as prepared LiMn₂O₄ showed a well-defined highly pure spinel single phase. The electrochemical performance of LiMn₂O₄ and its starting material γ-MnO₂ was evaluated through cyclic voltammetry, galvanostatic (constant current charge-discharge cycling) The electrochemical properties in terms of cycle performance were also discussed. γ-MnO₂ showed fairly high initial capacity of about 200 mAhg⁻¹ but poor cycle performance. LiMn₂O₄ samples showed fairly low initial capacity but good cycle performance.     

A novel approach to employ Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript> as anode active material for lithium batteries

In the present paper, we describe utilization of cathode active material as anode active material, for example, Li₂MnSiO₄. The lithium manganese silicate has been successfully synthesized by solid-state reaction method. The X-ray diffraction pattern confirms the orthorhombic structure with Pmn2 ₁ space group. The Li/Li₂MnSiO₄ cell delivered the initial discharge capacity of 420 mA h g⁻¹, which is 110 mA h g⁻¹ higher than graphitic anodes. The electrochemical reversibility and solid electrolyte interface formation of the Li₂MnSiO₄ electrode was emphasized by cyclic voltammetry.     

Enhancement of the electrochemical properties of LiMn2O4 by glycolic acid-assisted sol-gel method

LiMn₂O₄ spinel cathode was synthesized by the sol–gel method by using glycolic acid as a chelating agent. The sample exhibited a pure cubic spinel structure without any impurities in the X-ray diffraction (XRD) patterns. The result of the electrochemical performances on the sample compared to those of electrodes based on LiMn₂O₄ spinel synthesized by solid state. LiMn₂O₄ synthesized by glycolic acid-assisted sol–gel method improves the cycling stability of electrode. The capacity retention of sol–gel-synthesized LiMn₂O₄ was about 90• after 100 cycles between 3.0 and 4.4 V at room temperature. The electrochemical performance of the LiMn₂O₄ (sol–gel) and LiMn₂O₄ (solid state) were investigated under 40• between 3.0 and 4.4 V. XRD results of the cathode material after 50 cycles at 40• revealed that LiMn₂O₄ (sol–gel) could effectively suppress the LiMn₂O₄ dissolving of into electrolyte and resulted in a better stability.     

Electrochemical activities of yttrium doped spinel LiMn2O4

It was found for the first time that the catalysis of yttrium doping of spinel LiMn₂O₄ can enhance the electrochemical activities of manganese, leading to both improvement of electrochemical capacity and reactivity with the electrolyte of manganese. A proper amount of doping was 0.5%, and such yttrium-doped sample, Li(Y_0.005Mn_0.995)₂O₄, had an initial capacity of 130 mAh g⁻¹ over that of the undoped one with the capacity retention to reach 92.3% exceeding that of the undoped one at 100th cycle.     

Significance of Mg doped LiMn2O4 spinels as attractive 4 V cathode materials for use in lithium batteries

LiMn₂O₄ spinel is one of the most promising cathode materials for lithium-ion batteries because of its cheapness and eco-friendliness. Due to Jahn-Teller distortion, the capacity fades, however, upon repeated cycling. Attempts are being made to improve the cycle life of the spinel by substitution of manganese with other cations. In this paper we report the effect of partial substitution of manganese by Mg²⁺ ions in the LiMn₂O₄ phase. LiMg_yMn_2−yO₄ (y=0 – 0.3) has been synthesized by a thermal method and characterized using XRD, TG/DTA and FTIR. The electrochemical performance is correlated with the dopant concentration.     

LiFePO<Subscript>4</Subscript>/C with high capacity synthesized by carbothermal reduction method

The olivine-type LiFePO₄/C cathode materials were prepared via carbothermal reduction method using cheap Fe₂O₃ as raw material and different contents of glucose as the reducing agent and carbon source. Their structural and morphological properties were investigated by X-ray diffraction, scanning electron microscope, transmission electron microscope, and particle size distribution analysis. The results demonstrated that when the content of the carbon precursor of glucose was 16 wt.%, the synthesized powder had good crystalline and exhibited homogeneous and narrow particle size distribution. Even and thin coating carbon film was formed on the surface of LiFePO₄ particles during the pyrolysis of glucose, resulting in the enhancement of the electronic conductivity. Electrochemical tests showed that the discharge capacity first increased and then decreased with the increase of glucose content. The optimal sample synthesized using 16 wt.% glucose as carbon source exhibited the highest discharge capacity of 142 mAh g⁻¹ at 0.1C rate with the capacity retention rate of 90.4% and 118 mAh g⁻¹ at 0.5C rate.     

Synthesis of high performance Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C cathode material by ultrasonic-assisted sol–gel method

A novel ultrasonic-assisted sol–gel method is proposed to prepare Li₃V₂(PO₄)₃/C cathode material. X-ray diffraction analyses show that both Li₃V₂(PO₄)₃/C(A) synthesized by the ultrasonic-assisted sol–gel method and Li₃V₂(PO₄)₃/C(B) synthesized by a traditional sol–gel method have monoclinic structure. Scanning electron microscopy images indicate that the Li₃V₂(PO₄)₃/C(A) composite has a more uniform morphology than that of the Li₃V₂(PO₄)₃/C(B) composite. In the voltage range of 3.0–4.3 V (vs. Li/Li⁺), the initial specific discharge capacities of the Li₃V₂(PO₄)₃/C(A) and Li₃V₂(PO₄)₃/C(B) samples are 129.8 and 125.9 mAh g⁻¹ at 1C rate (1C = 133 mA g⁻¹), respectively. Furthermore, at 2-C charge/10-C discharge rate, the specific discharge capacity of the Li₃V₂(PO₄)₃/C(A) composite retains 113.2 mAh g⁻¹ after 50 cycles, but the Li₃V₂(PO₄)₃/C(B) composite only presents a capacity of 94.8 mAh g⁻¹.     

Influence of Sm<Superscript>3+</Superscript> ion in structural,morphological, and electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> synthesized by microwave calcination

LiSm_xMn_2–xO₄ samples were synthesized via co-precipitation technique. The structural properties of the synthesized materials were studied using X-ray diffraction analysis and it confirmed the cubic spinel structure for all the compounds. The lattice parameter of LiMn₂O₄ was observed to be 8.2347 Ǻ and it decreased with Sm³⁺ concentration, due to the shrinkage in cell volume aided by higher binding energy between Sm-O bond. The SEM micrographs were analyzed using Image processing software (Image-J) to ascertain the pore and grain properties. The microwave synthesis had been observed to control the bulk grain formation and had yielded lesser porous and nanoparticles. The particle size distributions obtained through photocross correlation laser diffraction analysis had shown that LiMn₂O₄ with 60 nm and Sm-doped compounds with ∼30 nm, respectively. The cyclic voltammetry studies had revealed the decrease in electrocatalytic behavior in the initial cycle for compounds doped with Sm³⁺ ion. The initial capacities of LiMn₂O₄, LiSm_0.05Mn_1.95O₄ and LiSm_0.10Mn_1.90O₄ substituted compounds were observed to be 134.87 mAhg⁻¹, 132.22 mAhg⁻¹ and 126.41 mAhg⁻¹, respectively. The cells were simulated using 1D model namely Dualfoil5.1 program. The simulated results coincide well with the measured results. The cycle life studies reveal 93% capacity retention of samarium-0.05-doped samples when compared with 78.4% of the LiMn₂O₄.     

Multi-faceted highly crystalline LiMn2O4 and LiNi0.5Mn1.5O4 cathodes synthesized by a novel carbon exo-templating method

LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ powders have been synthesized by a novel cost-effective carbon exo-templating process. It has been observed that controlled nucleation in the pores of highly surface active carbon produces a distinct effect on the powder morphology and crystallinity. Quantitative X-ray phase analyses show single phase spinel structure having Fd3m symmetry for both samples. Field emission electron microscopy reveals particles of size 0.5–1.0 µm with well defined multi-faceted crystals. Cyclic voltammetry results show well separated distinct redox peaks at 4.05/3.92 and 4.17/4.08 V for LiMn₂O₄/Li and 4.91/4.61 V for LiNi_0.5Mn_1.5O₄/Li coin cells indicating good crystallinity and reversibility of the cathodes compared to that of pristine LiMn₂O₄ synthesized by conventional combustion process. The LiMn₂O₄/Li and LiNi_0.5Mn_1.5O₄/Li cells deliver an initial discharge capacity of 110 mA h/g and 122 mA h/g respectively at a current density of 0.05 mA/cm² and when cycled at 0.2 mA/cm², the cells maintain 81% and 96% of their initial discharge capacity respectively even after 20 cycles. On the other hand, at the same current density, LiMn₂O₄ synthesized by conventional combustion process suffers from severe capacity fading (only 37.5% capacity retention after the 25th cycle). The capacity fading rate is found to be very less even at further higher current densities (0.4–0.8 mA/cm²) for both LiMn₂O₄/Li and LiNi_0.5Mn_1.5O₄/Li cells synthesized by the templating process. The present study reveals that high crystallinity along with multi-faceted morphology shows a remarkable enhancement in capacity as well as rate performance of pristine LiMn₂O₄ and its Ni derivative.     

Structural and electrochemical effects of cobalt doping on lithium manganese oxide spinel

Pure LiMn₂O₄ and lithium manganese oxide spinels with partial replacement of manganese by cobalt up to 20 mole%, LiCo_xMn_2−xO₄, were prepared. The effect of extended cycling on the crystal structure was investigated. A capacity decrease with increasing cobalt content was observed in the potential range about 4100 mV vs. Li/Li⁺. Cycling behavior is significantly improved, compared to LiMn₂O₄. LiCo_xMn_2−xO₄ is discharged in a single phase reaction in the upper potential range around 4100 mV vs. Li/Li⁺, whereas pure LiMn₂O₄ shows a two phase behavior. LiMn₂O₄ shows a significant broadening of peaks in plots of differential capacity and change in shape of the voltage profile upon extended cycling. LiCo_xMn_2−xO₄ shows neither broadening nor change. Voltage profiles and plots of the differential capacity differ significantly compared to spinels with lithium substitution, Li_1+xMn_2−xO₄. In contrast to Li_1+xMn_2-xO₄, LiCo_xMn_2-xO₄ is discharged in a two step process in the range of 0 ≤ × ≤ 0,5. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Physicochemical properties of LiAl x Mn2 − x O4 and LiAl0.05Mn1.95O4 − y F y cathode material by the citric acid-assisted sol–gel method

LiAl _x Mn_2 − x O₄ and LiAl_0.05Mn_1.95O_4 − y F _y spinel have been successfully synthesized by citric acid-assisted sol–gel method. The structure and physicochemical properties of this as-prepared powder were investigated by electronic conductivity test, powder X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), and galvanostatic charge–discharge test in detail. The electronic conductivity decreases with increasing of the content of doped Al. XRD patterns show that the diffraction of LiAl_0.05Mn_1.95O_4 − y F _y samples is similar, with all the peaks indexable in the Fd3m space group, and a little impurity appears in the LiAl_0.05Mn_1.95O_3.8F_0.2 sample. SEM reveals that all LiAl_0.05Mn_1.95O_4 − y F _y powders have the uniform, nearly cubic structure morphology with narrow size distribution which is less than 500 nm. Galvanostatic charge–discharge test indicates that LiAl_0.05Mn_1.95O₄ has the highest discharge capacity and electrochemical performance among all LiAl _x Mn_2 − x O₄ samples after 50 cycles, and the initial discharge capacity of LiAl_0.05Mn_1.95O_4 − y F _y (y = 0, 0.02, 0.05, 0.1) is 123.9, 124.6, 124.9, and 125.0 mAh g⁻¹, respectively, and their capacity retention ratios are 94.2%, 94.9%, 91.7%, and 89.9% after 50 cycles, respectively. EIS indicates that LiAl_0.05Mn_1.95O_3.98F_0.02 have smaller charge transfer resistance than that of LiAl_0.05Mn_1.95O₄ corresponding to the extraction of Li⁺ ions.     

Enhanced cyclability of triple-metal-doped LiMn2O4 spinel as the cathode material for rechargeable lithium batteries

To improve the cycle performance of spinel LiMn₂O₄ as the cathode of 4-V-class lithium secondary batteries, spinel phases LiM _x Mn_2 − x O₄ (M=Li, Fe, Co; x = 0, 0.05, 0.1, 0.15) and LiFe_0.05M _y Mn_{1.95 − y} O₄ (M=Li, Al, Ni, Co; y = 0.05, 0.1) were successfully prepared using the sol–gel method. The spinel materials were characterized by powder X-ray diffraction (XRD), elemental analysis, and scanning electron microscopy. All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. Electrochemical studies were carried out using the Li|LiM _x Mn_2 − x O₄ (M=Li, Fe, Co; x = 0, 0.05, 0.1, 0.15) and LiFe_0.05M _y Mn_{1.95 − y} O₄ (M=Li, Al, Ni, Co; y = 0.05, 0.1) cells. These cathodes were more tolerant to repeated lithium extraction and insertion than a standard LiMn₂O₄ spinel electrode in spite of a small reduction in the initial capacity. The improvement in cycling performance is attributed to the stabilization in the spinel structure by the doped metal cations.     

Preparation and electrochemical properties of nano Al<Subscript>0.2</Subscript>V<Subscript>2</Subscript>O<Subscript>5.3−<Emphasis Type="BoldItalic">δ</Emphasis></Subscript> cathode materials for rechargeable lithium batteries

Nano-sized Al³⁺-doped V₂O₅ cathode materials, Al_0.2V₂O_5.3−δ , were prepared by an oxalic acid assisted sol–gel method at 350 °C (sample A) and 400 °C (sample B). X-ray diffraction confirmed that samples A and B were pure phase Al_0.2V₂O_5.3−δ with an orthorhombic structure close to that of V₂O₅. Scanning electron microscopy showed that sample A was in nanoscale with a mean particle size about 50 nm. Cyclic voltammetry showed the good electrochemical and structural reversibility of the Al_0.2V₂O_5.3−δ nanoparticles during the Li⁺ insertion/extraction process. The Al_0.2V₂O_5.3−δ nanoparticles exhibited excellent charge–discharge cycling performance and rate capability compared to that of bulky V₂O₅ electrodes. For instance, the materials delivered a reversible specific capacity about 180 mAh g⁻¹ (sample A) and 150 mAh g⁻¹ (sample B), in the potential window of 4.0–2.0 V at the current density of 150 mA g⁻¹. The Al_0.2V₂O_5.3−δ nanoparticles in particular showed almost no capacity fading for at least 50 cycles.