Oxidation and Reduction Processes During NO x Removal with Corona-Induced Nonthermal Plasma

In this paper, the NO-to-NO ₂ conversion in various gaseous mixtures is experimentally investigated. Streamer coronas are produced with a dc-superimposed high-frequency ac power supply (10–60 kHz). According to NO _x removal experiments in N ₂ +NO _x and N ₂ +O ₂ +NO _x gaseous mixtures, it is supposed that the reverse reaction NO ₂ +ONO+O ₂ may not only limit NO ₂ production in N ₂ +NO _x mixtures, but also increase the energy cost for NO removal. Oxygen could significantly suppress reduction reactions and enhance oxidation processes. The reduction reactions, such as N+NON ₂ +O, induce negligible NO removal provided the O ₂ concentration is larger than 3.6%. With adding H ₂ O into the reactor, the produced NO ₂ per unit removed NO can be significantly reduced due to NO ₂ oxidation. NH ₃ injection could also significantly decrease the produced NO ₂ via NH and NH ₂ - related reduction reactions. Almost 100% of NO ₂ can be removed in gaseous mixtures of N ₂ +O ₂ +H ₂ O+NO ₂ with negligible NO production.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

CeO2-ZrO2-La2O3-Al2O3 composite oxide and its supported palladium catalyst for the treatment of exhaust of natural gas engined vehicles

Composite supports CeO2-ZrO2-Al2O3 (CZA) and CeO2-ZrO2-Al2O3-La2O3 (CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and NOx in the mixture gas simulated the exhaust from natural gas vehicles (NGVs) operated under stoichiometric condition was investigated. The effect of La2O3 on the physicochemical properties of supports and catalysts was characterized by various techniques. The characterizations with X-ray diffraction (XRD) and Raman spectroscopy revealed that the doping of La2O3 restrained effectively the sintering of crystallite particles, maintained the crystallite particles in nanoscale and stabilized the crystal phase after calcination at 1000 ℃. The results of N2-adsorption, H2-temperature-programmed reduction (H2-TPR) and oxygen storage capacity (OSC) measurements indicated that La2O3 improved the textural properties, reducibility and OSC of composite supports. Catalytic activity testing results showed that the catalysts exhibit excellent activities for the simultaneous removal of methane, CO and NOx in the simulated exhaust gas. The catalysts supported on CZALa showed remarkable thermal stability and catalytic activity for the three pollutants, especially for NOx. The prepared palladium catalysts have high ability to remove NOx, CH4 and CO, and they can be used as excellent catalysts for the purification of exhaust from NGVs operated under stoichiometric condition. They also have significant potential in industrial application because of their high performance and low cost.     

Catalytic reduction of nitrogen monoxide with propene over Nb/TiO2 mixed mechanically with Mn2O3

Selective catalytic reduction of nitrogen monoxide (NO) over a catalyst of mechanically mixed Nb/TiO₂ and Mn₂O₃ (Mn₂O₃+Nb/TiO₂) in an oxidizing atmosphere with propene (C₃H₆) was studied. The Mn₂O₃+Nb/TiO₂ catalyst showed high activity for the reduction of NO to N₂. The maximum conversion of NO to N₂ was observed at 200∼300°C, with about 80% reduction of NO to N₂. Mn₂O₃ enhanced the formation of NO₂ from NO and the activation of propene to react with NO₂ for reduction to N₂.     

NOx-Sorbing Metal Oxides, MnOx–CeO2. Oxidative NO Adsorption and NOx–H2 Reaction

(n)MnO_x–(1–n)CeO₂ binary oxides have been studied for the sorptive NO removal and subsequent reduction of NO_x sorbed to N₂ at low temperatures (150 °C). The solid solution with a fluorite-type structure was found to be effective for oxidative NO adsorption, which yielded nitrate (NO^– ₃) and/or nitrite (NO^– ₂) species on the surface depending on temperature, O₂ concentration in the gas feed, and composition of the binary oxide (n). A surface reaction model was derived on the basis of XPS, TPD, and DRIFTS analyses. Redox of Mn accompanied by simultaneous oxygen equilibration between the surface and the gas phase promoted the oxidative NO adsorption. The reactivity of the adsorbed NO_x toward H₂ was examined for MnO_x–CeO₂ impregnated with Pd, which is known as a nonselective catalyst toward NO–H₂ reaction in the presence of excess oxygen. The Pd/MnO_x–CeO₂ catalyst after saturated by the NO uptake could be regenerated by micropulse injections of H₂ at 150 °C. Evidence was presented to show that the role of Pd is to generate reactive hydrogen atoms, which spillover onto the MnO_x–CeO₂ surface and reduce nitrite/nitrate adsorbing thereon. Because of the lower reducibility of nitrate and the competitive H₂–O₂ combustion, H₂–NO reaction was suppressed to a certain extent in the presence of O₂. Nevertheless, Pd/MnO_x–CeO₂ attained 65% NO-conversion in a steady stream of 0.08% NO, 2% H₂, and 6% O₂ in He at as low as 150 °C, compared to ca. 30% conversion for Pd/–Al₂O₃ at the same temperature. The combination of NO_x-sorbing materials and H₂-activation catalysts is expected to pave the way to development of novel NO_x-sorbing catalysts for selective deNO_x at very low temperatures.     

Effect of conversion of NO2 into no on the catalytic reduction of NO2 with C3H6 in excess O2

During the reduction of NO₂ by C₃H₆ in O₂ over alumina-supported Au, Rh and Pt it was found that three parallel reactions take place,i.e., reduction of NO₂ to N₂ and N₂O, partial decomposition of NO₂ to NO and oxidation of C₃H₆ to CO and CO₂. In the absence of C₃H₆, the NO₂→NO+O₂ reaction reaches a fast equilibrium on Rh and Pt but not on Au and γ-Al₂O₃. Addition of C₃H₆ to the NO₂+O₂ mixture leads to the formation of NO above equilibrium conversion levels.     

The NiFe2O4 - MgFe2O4 series as electrode materials for electrochemical reduction of NO x

Solid solutions of spinel-type oxides with the composition (x = 0.0, 0.3, 0.5, 0.6, 1.0) were prepared with the glycine-nitrate combustion synthesis (x = 0.0, 0.3, 0.5, 0.6) and the citric-acid combustion synthesis (x = 1.0). The oxides were used as electrode materials in a pseudo-three-electrode setup in the temperature range of 400–600 °C. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the electrochemical behavior in 1% NO and 10% O₂. Measurements show that NiFe₂O₄ has relatively high cathodic activity in both NO and O₂, whereas MgFe₂O₄ shows much higher activity in NO compared to O₂. MgFe₂O₄ was also measured with cyclic voltammetry in 1% NO₂ and different gas mixtures of NO and O₂ at 300 and 400 °C. Results show that the cathodic activities (−0.6 V) are relatively high with current ratios, , ranging from 10.1–167.7 and with a maximum at 400 °C. Dilatometry measurements were performed on the materials in air up to 1,000 °C, and they showed that the Curie temperature could be detected for all samples. Four-point DC resistivity measurements at elevated temperatures show that Ni_0.4Mg_0.6Fe₂O₄ has the highest conductivity, whereas Ni_0.7Mg_0.3Fe₂O₄ and NiFe₂O₄ have the highest conductivity at lower temperatures.     

合成方法对Rh/CeO2-ZrO2-La2O3催化剂的结构、表面性能及DeNOx活性的影响

用沉积沉淀法合成两种不同系列的CeO2-ZrO2-La2O3混合氧化物(ZrO2和La2O3沉积CeO2粒子(标记为A-x)以及CeO2和La2O3沉积ZrO2粒子(标记为B-x)),并用作Rh催化剂的载体。XRD、拉曼、TPR、XPS和O2脉冲等表征结果显示出不同的沉积顺序将导致不同的结构和氧化还原性能,且B-x具有更高的氧迁移性、储氧能力和表面Ce浓度。当其负载Rh后,Rh/B-x催化剂具有更高的NO和CO转化率及N2选择性,且Ce的最佳含量为50at%。这可能归因于Rh负载于富铈表面形成更多有利于NO分解的表面Ce3+活性位。     

酸性金属氧化物对锰铈氧化物催化剂脱硝温度窗口的调控作用

利用溶胶-凝胶法,采用三种酸性金属氧化物（氧化铌、氧化钨和氧化钼）对锰铈复合氧化物催化剂进行了改性. 测试了催化剂的氮氧化物选择性催化还原（SCR）活性,以筛选对应不同温度窗口的合适酸性氧化物改性剂. 同时评价了催化剂的NO氧化和NH₃氧化活性. 利用X射线衍射、BET比表面积测试、H₂程序升温还原、NH₃/NO_x程序升温脱附和NH₃/NO_x吸附红外光谱等手段对催化剂进行了表征. MnO_x-CeO₂催化剂表现出良好的低温（100-150 ℃）活性. 酸性金属氧化物的添加削弱了催化剂的氧化还原特性,从而抑制了NH₃的活化和NO₂辅助的快速SCR反应. 与此同时,相对高温（250-350 ℃）区NH₃的氧化也受到了抑制,B酸和L酸上的NH₃吸附得以增强. 因此,催化剂的SCR脱硝温度窗口向高温移动,改性效果Nb₂O₅ < WO₃ < MoO₃.     

Point and Multipoint to Plane Barrier Discharge Process for Removal of NOx from Engine Exhaust Gases: Understanding of the Reactional Mechanism by Isotopic Labeling

An experimental study on the removal of NO_x in a simulated vehicle exhaust gas has been carried out using point to plane and multipoint to plane DBD corona reactors. Hydrocarbon (C₃H₆) and NO_x by-products were systematically investigated with a Gas Chromatography coupled to a Mass Spectrometry (GC/MS). NO_x (NO and NO₂) and CO output were also monitored with a gas analyzer in order to complete the mass balance. ¹⁸O tracer technique analyzes is applied to investigate the mechanism of propylene decomposition. From the plasma chemical reaction pathway proposed, it is apparent that the oxygen activation is one of the important steps for initiating the oxidation processes and the R-NO_x formation. We present data for the reaction of the (N₂/O₂/C₃H₆/CO₂NO/H₂O system in the corona discharge reactors mentioned above. This system has been shown to generate a significant amount of aldehyde. CH₃NO₂ and CH₃ONO₂ are the main R-NO_x compounds produced. Reactant composition and discharge energy densities (controlled by a numerical oscilloscope) were the operating parameters under study in wet and dry air mixture. Water vapors played an important role in NO_x removal (especially in NO₂ removal) via the reaction forming HNO₃. Therefore, in wet-gas mixture supplied reactors the highest removal rates of NO_x were as high as 30%, while in dry-gas only 15%. Different dielectric materials such as Al₂O₃/SiO₂ and TiO₂ on Al₂O₃/SiO₂ support have been used.     

Catalytically Promoted NOx Sorption by ZrO2-Based Oxides

Metal promoted zirconia-based oxide sorbents, such as Pt–ZrO₂/Al₂O₃ for NO _x have been investigated. To clarify the role of the catalyst component, sorption of NO and NO₂ was compared using the samples with and without Pt. The catalytic oxidation of NO to NO₂ and successively to nitrate ions is an important role for the Pt catalyst. The experimental results indicate that a high-temperature calcination is essential to remove residual Cl from Pt–ZrO₂–Al₂O₃ prepared from H₂PtCl₆ in order to provide more active NO _x sorption sites. Of M–ZrO₂–Al₂O₃ samples investigated, ruthenium as well as Pt demonstrated relatively good performance as a catalyst component in the sorbent. The FT-IR spectra after sorption of NO and NO₂ demonstrated a strong band attributed to stored nitrate ions. The Pt catalyst was more resistant to sulfur poisoning than a base metal catalyst. However, the NO _x sorptive capacities of the Pt–ZrO₂/Al₂O₃ sorbents were expected to be deteriorated in dilute SO₂ as far as observed from FT-IR spectra.     

荧光XAFS表征Pt/BaAl2O4-Al2O3催化剂中的微量铂物种

随着稀薄燃烧(lean-burn)发动机的推广使用和环保法规的日趋严格,消除稀燃尾气中的氮氧化物(N O x)已刻不容缓。N O x储存还原技术被认为是最具应用前景的方法之一[1,2]。目前,对Pt/BaA l2O4-A l2O3体系中N O x储存与还原机制的研究较多[1￣4],但对该体系中微量铂物种微观结构及其与性能的关系研究较少,这主要是由于Pt含量(0.1w t%￣0.5wt%)太低,分散度较高,使表征方法受到很大限制。本文采用共沉淀-浸渍法制得具有较高比表面积和热稳定性的N O x储存还原催化剂Pt/BaA l2O4-A l2O3,应用荧光X-射线吸收精细结构方法(Fluores-cence-…     

Review of Ag/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Reductant System in the Selective Catalytic Reduction of NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

Ag/Al₂O₃ is a promising catalyst for the selective catalytic reduction (SCR) by hydrocarbons (HC) of NO _x in both laboratory and diesel engine bench tests. New developments of the HC-SCR of NO _x over a Ag/Al₂O₃ catalyst are reviewed, including the efficiencies and sulfur tolerances of different Ag/Al₂O₃-reductant systems for the SCR of NO _x ; the low-temperature activity improvement of H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃; and the application of a Ag/Al₂O₃-ethanol SCR system with a heavy-duty diesel engine. The discussions are focused on the reaction mechanisms of different Ag/Al₂O₃-reductant systems and H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃. A SO₂-resistant surface structure in situ synthesized on Ag/Al₂O₃ by using ethanol as a reductant is proposed based on the study of the sulfate formation. These results provide new insight into the design of a high-efficiency NO _x reduction system. The diesel engine bench test results showed that a Ag/Al₂O₃-ethanol system is promising for catalytic cleaning of NO _x in diesel exhaust.     

Nox reduction with CO over supported Pd catalysts under simulated post Euro-IV diesel exhaust conditions

The catalytic reduction of NO_x with CO over Pd/Al₂O₃ and Pd/TiO₂/Al₂O₃ under simulated post Euro-IV diesel exhaust conditions was studied. The catalytic activities obtained by using various Pd and TiO₂ loadings and total amounts of reductant and the influence of H₂ and H₂O was investigated.     

Effect of NO, SO2, and O2 on the conversion of nitrous oxide on iron-containing zeolite catalysts

Conditions were found for facilitation of the conversion of nitrous oxide in the presence of Fe-containing zeolite catalysts by oxidants (NO, SO₂, and O₂). The results were interpreted in the framework of a mechanism involving decomposition of N₂O. The effect of NO_x on the reduction of nitrous oxide by C₃-C₄ alkanes was established. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 42, No. 4, pp. 241–245, July–August, 2006.     

CARS Diagnostic and Modeling of a Dielectric Barrier Discharge

Dielectric barrier discharges (DBD) with planar- and knife-shaped electrodes are operated in N₂O₂NO mixtures under a pressure of 20 and 98 kPa. They are excited by means of consecutive unipolar or bipolar high-voltage pulse packages of 10 kV at a pulse repetition rate of 1 and 2 kHz. The rotational and vibrational excitation of N ₂ molecules and the reduction of nitric oxide (NO) in the discharge have been investigated using coherent anti-Stokes Raman scattering (CARS) technique. Rotational (gas) temperatures near the room temperature and vibrational temperatures of about 800 K at atmospheric pressure and 1400 K at a pressure of 20 kPa are observed. Therefore, chemical reactions of NO with vibrationally excited N ₂ are probably insignificant. One-dimensional kinetic models are developed that balance 35 chemical reactions between 10 species and deliver equations for the population density of excited vibrational levels of N ₂ together with a solution of the Boltzmann equation for the electrons. A good agreement between measured vibrational temperatures of N ₂ , the concentration of NO, and calculated data is achieved. Modeling of the plasma discharge verifies that a DBD operated with a N₂NO mixture reduces the NO content, the simultaneous presence of O ₂ , already 1%, is enough to prevent the NO reduction.     

Thermal decomposition of cobalt nitrato compounds: Preparation of anhydrous cobalt(II)nitrate and its characterisation by Infrared and Raman spectra

The thermal decomposition of Co(NO₃)₂·6H₂O (1) as well as that one of NO[Co(NO₃)₃] (Co(NO₃)₂·N₂O₄) (2) was followed by thermogravimetric (TG) measurements, X-ray recording and Raman and IR spectra. The stepwise decomposition reactions of 1 and 2 leading to anhydrous cobalt(II)nitrate (3) were established. In N₂ atmosphere, cobalt oxides are finally formed whereas in H₂/N₂ (10% H₂) cobalt metal is produced. Rapid heating of cobalt(II)nitrate hexahydrate causes melting (formation of a hydrate melt) and therefore side reactions in the hydrate melt by incoupled reactions and evolution/evaporation of different species as, e.g., HNO₃, NO₂, etc. In case of larger amounts in dense packing in the sample container, the formation of oxo(hydoxo)nitrates is possible at higher temperature. For 2, its thermal decomposition to 3 was followed and its decomposition mechanism is proposed.     

PbCu3(OH)(NO3)(SeO3)3·1/2H2O und Pb2Cu3O2(NO3)2(SeO3)2: Synthese und Kristallstrukturuntersuchung

Crystals of PbCu₃(OH)(NO₃)(SeO₃)₃·1/2H₂O [a=7.761(3)Å,b=9.478(4)Å,c=9.514(4)Å, =66.94(2)°, =69.83(2)°, =81.83(2)°, space group P ,Z=2] and Pb₂Cu₃O₂(NO₃)₂(SeO₃)₂ [a=5.884(2)Å,b=12.186(3)Å,c=19.371(4)Å, space group Cmc2₁,Z=4] were synthesized under hydrothermal conditions. Their crystal structures were refined with three-dimensional X-ray data toR _w=0.033 resp. 0.055. In PbCu₃(OH)(NO₃)(SeO₃)₃·1/2H₂O the Cu atoms are [4+1] and [4+2] coordinated and via SeO₃ groups a three-dimensional atomic arrangement is built up. In Pb₂Cu₃O₂(NO₃)₂(SeO₃)₂ there are sheets, which are connected only via Pb-O bonds ranging from 2.98 Å to 3.16 Å.

     

Highly Active and Stable Pt-USY in the Low-Temperature de-NOx HC-SCR

Selective catalytic reduction of NO_x by propene has been investigated on Pt-USY and compared to other Pt-catalysts. The catalyst was characterized by XRD, Ar adsorption at 87 K, TEM, and CO chemisorption, and tested in a gas mixture system in excess oxygen. Pt-USY shows an excellent activity in the reaction, with a molar NO_x conversion of 90% at 475 K. Stability during time-on-stream and resistance to SO₂ and H₂O in the feed stream has also been investigated. Pt-USY performs better under lean-burn conditions than other Pt-catalysts on ZSM-5, Al₂O₃, or SiO₂. The selectivity to N₂ was similar for all the catalysts (30%), the other major product being N₂O.     

Study of NOx and CO2 production of cultivated soil in closed microcosm experimental system

The aim of present project was to develop a microcosm experimental method for estimation of NO_x and CO₂ emission of microbial origin from cultivated soil. The effect of different factors (such as temperature, water supply, mineral-N source and organic matter addition, role of soil organisms and heavy metal contamination) that controlling the accumulation of N₂O and CO₂ in soil atmosphere and release to air was studied in closed microcosm laboratory model experiments. The headspace gas composition of closed glass vessels of 800-1200 cm³ containing 100-200 g brown forest soil sample was analysed. The N₂O and CO₂ concentration of gas samples was analysed by gas chromatographic methods and NO-content by means of chemiluminescent detection. Concerning the results, it can be stated that the applied microcosm experimental model proved to be a suitable tool for detecting the effect of factors influencing the NO_x and CO₂ release from agricultural soil. The temporal changes of N₂O and CO₂ concentration demonstrated the impact of the coupled microbial processes resulting in these greenhouse gases. The gas production depended on the soil moisture level, temperature and C/N ratio significantly. The inhibitory effect of toxic heavy metals (e.g. Cd) could also be affected by the C/N ratio. The appearance of NO as an intermediate of microbial processes was observed as well.