An off-line automated preconcentration system with ethylenediaminetriacetate chelating resin for the determination of trace metals in seawater by high-resolution inductively coupled plasma mass spectrometry

A novel automated off-line preconcentration system for trace metals (Al, Mn, Fe, Co, Ni, Cu, Zn, Cd, and Pb) in seawater was developed by improving a commercially available solid-phase extraction system SPE-100 (Hiranuma Sangyo). The utilized chelating resin was NOBIAS Chelate-PA1 (Hitachi High-Technologies) with ethylenediaminetriacetic acid and iminodiacetic acid functional groups. Parts of the 8-way valve made of alumina and zirconia in the original SPE-100 system were replaced with parts made of polychlorotrifluoroethylene in order to reduce contamination of trace metals. The eluent pass was altered for the back flush elution of trace metals. We optimized the cleaning procedures for the chelating resin column and flow lines of the preconcentration system, and developed a preconcentration procedure, which required less labor and led to a superior performance compared to manual preconcentration (Sohrin et al. [5]). The nine trace metals were simultaneously and quantitatively preconcentrated from ∼120 g of seawater, eluted with ∼15 g of 1 M HNO₃, and determined by HR-ICP-MS using the calibration curve method. The single-step preconcentration removed more than 99.998% of Na, K, Mg, Ca, and Sr from seawater. The procedural blanks and detection limits were lower than the lowest concentrations in seawater for Mn, Ni, Cu, and Pb, while they were as low as the lowest concentrations in seawater for Al, Fe, Co, Zn, and Cd. The accuracy and precision of this method were confirmed by the analysis of reference seawater samples (CASS-5, NASS-5, GEOTRACES GS, and GD) and seawater samples for vertical distribution in the western North Pacific Ocean.     

Multielement preconcentration of trace heavy metals in seawater with an emulsion containing 8-quinolinol for graphite-furnace atomic absorption spectrometry

A water-in-oil type emulsion containing 8-quinolinol has been used for the concentration of traces of heavy metals from seawater prior to their determinations by graphite-furnace atomic absorption spectrometry. The emulsion used was prepared by dissolving 40 mg of 8-quinolinol and 60 mg of sorbitan monooleate (Span-80) in 3.0 ml of toluene and vigorously mixing with 0.70 ml of aqueous hydrochloric acid solution (1.5 mol l⁻¹) by ultrasonic irradiation. The resulting emulsion was gradually injected into 100 ml of sample solution (pH 8.5) and dispersed by stirring as numerous tiny globules. Four heavy metals (Co, Ni, Cu, and Cd) in the sample solution were quantitatively transported through the organic layer into the acidic aqueous droplets encapsulated in the emulsion. After collecting the dispersed emulsion globules, they were demulsified by heating and the heavy metals in the segregated aqueous phase were determined by atomic absorption spectrometry. Owing to the highly efficient concentration (100-fold), these heavy metals at sub-ng ml⁻¹ levels in seawater were determined with satisfactory accuracy and precision, being confirmed with certified reference samples.     

Determination of 232Th in seawater by ICP-MS after preconcentration and separation using a chelating resin

This article describes an analytical method for the separation, preconcentration and determination of ²³²Th in seawater samples at sub-ng/L levels using a NOBIAS CHELATE PA1 resin and a sector field (SF) inductively coupled plasma mass spectrometer (ICP-MS). The resin showed excellent adsorption of ²³²Th at a low pH of 2.4 ± 0.4 in a relatively small volume (200 mL) of seawater. ²³²Th adsorbed on the resin was easily eluted using 5 mL of 0.8 M HNO₃. An enrichment factor of 40 was achieved for ²³²Th analysis. Ethylenediamine-tetraacetic acid disodium salt dehydrate (EDTA) was used to investigate the effect of ²³²Th-binding organic ligand on the retention of ²³²Th on the chelating resin. Results obtained using acidified samples (pH of 2.4 ± 0.4) showed EDTA had no significant effect on ²³²Th recovery, indicating that at this low pH, ²³²Th was dissociated from the ²³²Th-binding organic ligand and quantitatively retained on the NOBIAS CHELATE PA1 resin. The developed analytical method was characterized by a separation and preconcentration taking approximately 4 h and a low detection limit of 0.0038 ng/L for ²³²Th, and was successfully applied to the determination of ²³²Th in seawater samples collected from coastal areas, Japan.     

Multielement determination of trace metals in river water (certified reference material, JSAC 0301-1) by high efficiency nebulization ICP-MS after 100-fold preconcentration with a chelating resin-packed minicolumn.

The determination of 34 trace metals in a river water certified reference material (CRM), i.e. JSAC 0301-1, which was issued by the Japan Society for Analytical Chemistry in January 2004, was performed by ICP-MS with a high efficiency nebulizer after preconcentration with a laboratory-made chelating resin-packed minicolumn, with which trace metals were concentrated 100-fold from 50 mL of a river water sample to 0.5 mL of the final analysis solution. Trace metals in JSAC 0301-1 were observed in the concentration range from 19 microg L(-1) of Al to 0.000053 microg L(-1) of Bi. It was found that most of the concentrations of trace metals, including rare earth elements (REEs), in JSAC 0301-1 were lower than those in JAC 0031, which was also a previously issued CRM prepared with water from the same river as that of JSAC 0301-1. The low concentrations of trace metals in JSAC 0301-1 might be attributed to the fact that there was a heavy rain before collecting the original water sample to prepare the present CRM. Furthermore, the REE distribution patterns of JSAC 0301-1, JAC 0031 and the average values of river water samples in Japan were parallel to each other. These results indicate that the distributions of REEs in JSAC 0301-1 and JAC 0031 were the typical ones of river water samples in Japan.     

Determination of trace metals in seawater by an automated flow injection ion chromatograph pretreatment system with ICPMS

A novel flow injection ion chromatograph (FI-IC) system has been developed to fully automate pretreatment procedures for multi-elemental analysis of trace metals in seawater by inductively coupled plasma mass spectrometer (ICPMS). By combining 10-port, 2 position and 3-way valves in the FI-IC manifold, the system effectively increase sample throughput by simultaneously processing three seawater samples online for: sample loading, injection, buffering, preconcentration, matrix removal, metal elution, and sample collection. Forty-two seawater samples can be continuously processed without any manual handing. Each sample pretreatment takes about 10 min by consuming 25 mL of seawater and producing 5 mL of processed concentrated samples for multi-elemental offline analysis by ICPMS. The offline analysis improve analytical precision and significantly increase total numbers of isotopes determined by ICPMS, which include the metals Al, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Ti, V, and Zn. The blank value and detection limits of trace metals using the system with ICPMS analysis all range from 0.1 to 10 parts per trillion (ppt), except Al, Fe, and Zn. The accuracy of the pretreatment system was validated by measuring open-ocean and coastal reference seawater, NASS-5 and CASS-4. Using the system with ICPMS analysis, we have obtained reliable trace metal concentrations in the water columns of the South China Sea. Possessing the features of full automation, high throughput, low blank, and low reagent volume used, the system automates and simplifies rigorous and complicated pretreatment procedures for multi-elemental analysis of trace metals in seawater and effectively enhances analytical capacity for trace metal analysis in environmental and seawater samples.     

新型螯合树脂在线预富集测定海水中痕量Cd

将新型螯合树脂(XAD-H2Dz)应用于微柱现场在线采样(MFS)新技术中,实现了海水样中痕量Cd的在线原位预富集和实验室中流动注射-火焰原子吸收(FI-FAAS)系统的联机测定。采样体积为5 mL和50 mL时,检出限(3σ)分别为68和6.7 ng/L;相对标准偏差(n=7)分别为2.0%和2.6%。对国家海水微量元素标准物质GBW(E)080040和实际样品(大连老虎滩区域海水以及连云港黄海水域)中镉进行分析,均获得了满意的结果。     

Determination of REEs in seawater by ICP-MS after on-line preconcentration using a syringe-driven chelating column

A syringe-driven chelating column (SDCC) was applied to develop an on-line preconcentration/inductively coupled plasma mass spectrometry (ICP-MS) method for preconcentration and determination of rare earth elements (REEs) in seawater samples. The present on-line preconcentration system consists of only one pump, two valves, an SDCC, an ICP-MS, several connectors, and Teflon tubes. Optimizations of adsorption pH condition, sample loading flow rate, and integration range were carried out to achieve optimum measurement conditions for REEs in seawater sample. Six minutes was enough for a preconcentration and measurement cycle using 10 mL of seawater sample, where the detection limits for different REEs were in the range of 0.005 pg mL⁻¹ to 0.09 pg mL⁻¹. Analytical results of REEs in a seawater certified reference material (CRM), NASS-5, confirmed the usefulness of the present method. Furthermore, concentrations of REEs in Nikkawa Beach coastal seawater were determined and discussed with shale normalized REE distribution pattern.     

Preparation of a reference mussel tissue material for polycyclic aromatic hydrocarbons and trace metals determination

Due to high cost of certified reference materials (CRMs), reference materials (RMs) are preferred to check the method performance in environmental analysis. In this work, a laboratory reference material (LRM) was prepared and characterised to carry out the quality control in monitoring analysis of eight polycyclic aromatic hydrocarbons (PAHs) and nine trace metals in mussel tissue. Mussels were collected in a naturally polluted area. Before the reference material was bottled, the mussel tissue was stabilised by freeze-drying, ground and sieved. For the material characterisation, several statistical tests were applied to check the homogeneity of the analytes in the tissue, and a stability test was performed to study the effect of the storage temperature in the analyte concentration. Other characteristics such as specific density, moisture and lipid contents as well as particle size distribution of the material were determined. Although the LRM had a homogeneous distribution for all PAHs and almost all metals, the stability study showed different results at both storage temperatures studied. For both PAHs and trace metals, the material was suitable to assure the quality control of the analysis.     

On-line preconcentration and GFAAS determination of trace metals in waters

An on-line separation preconcentration system coupled to electrothermal (graphite furnace) atomic absorption spectrometry was developed. A miniature column packed with iminodiacetic acid ethyl cellulose (IDAEC) was inserted into the loop. A peristaltic pump was used to deliver solutions. A flow of air was driven into the packed column, evacuating it between sample loading, washing and elution. The retained analyte was introduced on-line to graphite furnace using countercurrent elution with HNO₃. The system was applied for the determination of V, Co and Pb in medicinal mineral water samples, and nickel in sea water samples. The detection limits (3σ) were 0.058, 0.022, 0.067, 0.062 μg/l for Co, Pb, V, and Ni, respectively. The R.S.D. (n=5) was <5% at 0.4–1.0 μg/l concentration range.     

新型螯合棉分离抑制动力学光度法测定痕量铅

研究了在硼砂 氢氧化钠介质中 ,以 2 ,2′ 联吡啶为活化剂 ,Pb2 +对过氧化氢氧化偶氮氯磷 (Ⅲ )褪色反应具有的作用及其动力学条件 ,从而建立了一种测定痕量铅的新的动力学光度法 ,该方法的检出限为 3 9× 1 0 - 1 1 g/mL ,线性范围为 0～ 1 0 μg/1 0mL ,采用自制的MBM新型螯合棉纤维分离富集 ,可用于环境样品中痕量Pb2 +的测定。     

Preparation and certification of a reference material for the determination of nutrients in seawater

There is an urgent need for natural water reference materials certified for nutrients. In 1996, NRC collected seawater for a proposed CRM at a depth of 200 m in the North Atlantic; this was immediately filtered through 0.05-m cartridge filters into 50-L carboys. The water was later homogenized in the NRC laboratories in Ottawa and stabilized via gamma irradiation. Over six years of stability testing no significant deterioration was detected. In addition to the usual customary standard colorimetric procedures, alternative analytical methods were developed to enable the certification process. The production of a CRM called MOOS-1 will be discussed. Certified values, with uncertainty components addressing the homogeneity, stability, and characterization of the material, were calculated to be: orthophosphate=1.56±0.07 µmol L^–1, silicate=26.0±1.0 µmol L^–1, nitrite=3.06±0.15 µmol L^–1, and nitrite and nitrate=23.7±0.9 µmol L^–1.     

ICP-MS determination of heavy metals in submerged cultures of wood-rotting fungi

Accumulation of five heavy metal ions by five species of wood-rotting basidiomycetes during a 9-day cultivation was studied. Contents of Cd, Cu, Pb, and Zn were measured using ICP-MS; the amount of mercury was determined directly in solid samples using the Advanced Mercury Analyser. A standard operation procedure for the sample preparation and determination of metal content was developed and validated. Presence of Cd, Cu, Hg, and Pb decreased the accumulation of zinc by the fungi. The basidiomycete Pycnoporus cinnabarinus exhibited the highest metal binding capacity of all fungi tested.     

Trace metals analysis in estuarine and seawater by ICP-MS using on line preconcentration and matrix elimination with chelating resin

The main difficulties of trace metals analysis in estuarine and seawater stem from their very low concentration (mug/l to sub-mug/l), and, by contrast, the high salt content (up to 38 g/l in the Mediterranean Sea). ICP-MS allows multi-elemental analysis and offers great sensitivity, but may be strongly affected by matrix effects induced by high salt contents (> 1 g/l). To perform trace metals analysis both in riverine, estuarine and seawater, we have developed a hyphenated method: ion chelation chromatography coupled on-line with ICP-MS. Iminodiacetate resin, Metpac CC-1 (Dionex), was used to concentrate most of the trace metals, and to separate them from alkaline and alkaline-earth metals. Behaviour of 17 elements (Pb, Cu, Cd, Ni, U, Cr, Mn, Al, Co, Ga, In, Zn, V, Tl, Bi, Ag and Sn) towards the resin was qualitatively investigated. A method validation, partly derived from AFNOR standard XPT 90-210, was carried out on 12 elements (Pb, Cu, Cd, Ni, U, Cr, Mn, Al, Co, Ga, Bi and In). Replicate measurements of multi-elemental standard solutions were used to check linearity, and to determine repeatability and detection limits. Method accuracy was then assessed by analysing two certified materials: a synthetic freshwater (SRM 1643d), and a natural filtered coastal seawater (NRCC CASS-3). An application assay of natural samples from the Rh?ne river (France) was eventually carried out, and the analytical results were found to be consistent with previous works.     

Determination of trace elements in seawater samples by on-line column extraction/graphite furnace atomic absorption spectrometry

An innovative procedure for the on-line coupling of ion chromatography with graphite furnace atomic absorption spectrometry is described, which is particularly effective for the determination of trace metals in seawater samples. The Capillary Injection Device (CID) is used as an interface which allows the eluent to be transferred from the chromatographic column into the graphite tube at a flow rate of as high as 2 ml/min. The analytical procedure is based on the metal complex formation with 8-hydroxyquinoline in the sample solution, followed by the preconcentration of the complexes in a chromatographic column packed with XAD-2 resin. The complexes were then eluted from the column with methanol, and quantitatively injected into the furnace. The procedure was validated by determining cadmium and lead in certified reference seawater samples at a level of 30–40 pg/g, with a typical reproducibility of 10% and an accuracy of better than 5%. Finally, it was tested on a real sample of seawater. Due to the high reproducibility, a pg/g concentration level can be measured.     

Shipboard analysis of picomolar levels of manganese in seawater by chelating resin concentration and chemiluminescence detection

A new shipboard analytical method for determining picomolar levels of manganese in seawater has been developed. The method is based on a combination of chelating resin column extraction and improved chemiluminescence (CL) detection in a closed flow system. In this method, manganese in sample solution is selectively collected on newly-developed iminodiacetate-immobilized chelating resin, and then eluted with acidic solution containing hydrogen peroxide. The resulting eluent is mixed with luminol solution and aqueous ammonia after removal of iron ions by a chelating resin column, and then the mixture is introduced into the CL cell. The manganese concentration is obtained from the CL intensity. The detection limit (3SD) of manganese is 5 pmol L^–1 from 9 mL of seawater sample. The method was applied to seawater samples collected at the Okinawa Trough.     

ICP-MS法测定高纯钛中痕量元素

建立了ICP-MS直接测定高纯钛中Be,V,Co,Ni,Ga,Mo,Nb,Cd,Sb,TI,Pb的分析方法,并对ICP-MS工作参数及条件进行了优化和选择.高纯钛用HF与HNO3溶解后加入Sc、Cs、Re内标,用ICP-MS直接检测.方法的检出限为0.03～0.1 ng/mL,测定下限为0.2～0.5 ng/mL,各元...     

Comparison of liquid-liquid extraction, solid-phase extraction and co-precipitation preconcentration methods for the determination of cadmium, copper, nickel, lead and zinc in seawater

Three major types of pre-concentration methods were evaluated and optimised for the extraction and determination of Cd, Cu, Ni, Pb and Zn from seawater samples. The traditional APDC/DDDC-Freon liquid-liquid extraction method showed excellent results for a multi-elemental analysis. However, the technique is labour consuming, very sensitive to operational conditions, employs environmentally unsafe and expensive solvents and requires large sample volumes. In the solid phase extraction method, the performances of a traditional Amberlite XAD-4 and a novel Dowex Optipore V-493 were evaluated. Application of Dowex Optipore V-493 resin provided better results at low concentrations than the generally used Amberlite XAD-4 resin using low sample volumes. However, the presence of natural organic compounds may decrease extraction efficiency of both resins for Cu. Thus, a pre-treatment with UV irradiation is advantageous for samples with high organic content. Cobalt co-precipitation methods showed good Cu and Ni recoveries, but gave poor results for Cd at low concentrations. In addition, high sample volumes are required. Both solid phase and co-precipitation methods showed unsatisfactory results in determination of Pb. Finally, a summary of methods advantages are given for choosing the most suitable method.     

Simultaneous determination of suspended particulate trace metals (Co, Ni, Cu, Zn, Cd and Pb) in seawater with small volume filtration assisted by microwave digestion and flow injection inductively coupled plasma mass spectrometer

A new technique for the determination of suspended particulate trace metals (P-metals >0.2 μm), such as Co, Ni, Cu, Zn, Cd and Pb, in open ocean seawater has been developed by using microwave digestion coupled with flow injection inductively coupled plasma mass spectrometry (FI-ICP-MS). Suspended particulate matter (SPM) was collected from 500 mL of seawater on a Nuclepore filter (0.2 μm) using a closed filtration system. Both the SPM and filter were completely dissolved by microwave digestion. Reagents for the digestion were evaporated using a clean evaporation system, and the metals were redissolved in 0.8 M HNO₃. The solution was diluted with buffer solution to give pH 5.0 and the metals were determined by FI-ICP-MS using a chelating adsorbent of 8-hydroxyquinoline immobilized on fluorinated metal alkoxide glass (MAF-8HQ). The procedure blanks with a filter were found to be 0.048 ± 0.008, 10.3 ± 0.3, 0.27 ± 0.05, 3.3 ± 1.8, 0.02 ± 0.03 and 0.85 ± 0.09 ng L⁻¹ for Co, Ni, Cu, Zn, Cd and Pb, respectively (n = 14). Detection limits defined as 3 times the standard deviation of the blanks were 0.023, 0.90, 0.14, 5.3, 0.078 and 0.28 ng L⁻¹ for Co, Ni, Cu, Zn, Cd and Pb, respectively. Accuracy was evaluated using certified reference materials of chlorella (NES CRM No. 3) and marine sediment (HISS-1). The method was applied to the determination of vertical distributions for P-Co, Ni, Cu, Zn, Cd and Pb in the Western North Pacific.     

Rapid collection of iron hydroxide for determination of Th isotopes in seawater

This work introduces a novel method of recovery of iron hydroxide using a DIAION CR-20 chelating resin column to determine Th isotopes in seawater with a sector field (SF) inductively coupled plasma mass spectrometer (ICP-MS). Thorium isotopes in seawater were co-precipitated with iron hydroxide, and this precipitate was sent to chelating resin column. Ferric ions in the iron hydroxide were bonded to functional groups of the chelating resin directly, resulting in a pH increase of the effluent by release of hydroxide ion from the iron hydroxide. The co-precipitated thorium isotopes were quantitatively collected within the column, which indicated that thorium was retained on the iron hydroxide remaining on the chelating column. The chelating column quantitatively collected ²³²Th with iron hydroxide in seawater at flow rates of 20–25 mL min⁻¹. Based on this flow rate, a 5 L sample was processed within 3–4 h. The >20 h aging of iron hydroxide tends to reduce the recovery of ²³²Th. The rapid collection method was successfully applied to the determination of ²³⁰Th and ²³²Th in open-ocean seawater samples.     

GD-MS法和ICP-MS法测定高纯铌中痕量元素

采用辉光放电质谱法(GD-MS)对高纯铌中Ta,Mo,W等痕量杂质元素进行了测试,并对GD-MS工作参数进行了优化,部分元素与采用电感耦合等离子体质谱法(ICP-MS)定量分析的结果进行比较,对某些元素含量差别较大的原因进行了分析,论述了Element GD辉光放电质谱仪的特点及其在痕量杂质分析上的优势。