Use of 1,5-bis(di-2-pyridyl)methylene thiocarbohydrazide immobilized on silica gel for automated preconcentration and selective determination of antimony(III) by flow-injection electrothermal atomic absorption spectrometry

Selective sorption of Sb(III) on a microcolumn packed with 1,5-bis(di-2-pyridyl)methylene thiocarbohydrazide immobilized on silica gel (DPTH-gel) has been used for determination of Sb(III). A flow-injection system comprising a microcolumn connected to the tip of the autosampler was used for preconcentration. The sorbed antimony was eluted with nitric acid directly into the graphite furnace and determined by AAS. The detection limit for antimony under the optimum conditions was 0.3 ng mL^–1. This procedure was used for determination of antimony in natural water, soil, vegetation, and a certified sample of a city waste incineration ash (BCR 176).     

Electrothermal atomic absorption spectrometric determination of lead in high-purity reagents with flow-injection on-line microcolumn preconcentration and separation using a macrocycle immobilized silica gel sorbent

A fully automated procedure for the determination of ng l⁻¹ amounts of lead has been developed using flow injection (FI) online column preconcentration coupled with electrothermal atomic absorption spectrometry (ETAAS). The proposed FI manifold and its operation make possible the introduction of the total eluate volume into the graphite atomizer, avoiding the necessity for optimization of subsampling the eluate. The interference of other heavy metal ions due to competition for active sites of the sorbent is overcome using a highly selective macrocycle immobilized on silica gel (Pb-02). Lead is adsorbed on a microcolumn (50 μl) packed with Pb-02, and after washing the column with dilute nitric acid, air is introduced to remove all solution from the column and connecting tubing. The sorbed analyte is then eluted quantitatively into the graphite tube atomizer, preheated to 100°C, with 36 μl of ETDA solution (0.035 mol l⁻¹, pH 10.5), propelled by air in order to minimize dispersion. The collection efficiency was 77% and with a sample loading flow rate of 3 ml min⁻¹ and a 60 s preconcentration time, the enhancement factor was 77 and the throughput was 17 samples per hour. The relative standard deviation (n = 10) at the 300 ng l⁻¹ level was 2.7%, and the detection limit (3σ) was 0.4 ng l⁻¹. No interference from heavy metals was observed, but ions of Ba²⁺, Sr²⁺ and K⁺ were found to interfere when the concentration ratios of interferent to lead exceeded values of 2000, 20 000 and 200 000, respectively. Quantitative recovery of lead was achieved from sodium, magnesium, aluminum, lanthanum and heavy metal salt solutions. The high selectivity and sensitivity, combined with extremely low blank values, make the proposed technique particularly attractive for the analysis of high-purity reagents, semiconductors and other high-purity materials. Results are presented for the determination of lead in some high-purity reagents.     

Determination of antimony(III) and total antimony by single-drop microextraction combined with electrothermal atomic absorption spectrometry

A simple and sensitive method for using electrothermal atomic absorption spectrometry (ET AAS) with Rh as permanent modifier determination of Sb(III) and total Sb after separation and preconcentration by N-benzoyl-N-phenylhydroxylamine (BPHA)-chloroform single drop has been developed. Parameters, such as pyrolysis and atomization temperature, solvent type, pH, BPHA concentration, extraction time, drop size, stirring rate and sample volume were investigated. Under the optimized experimental conditions, the detection limits (3σ) were 8.0 ng L⁻¹ for Sb(III) and 9.2 ng L⁻¹ for total Sb, respectively. The relative standard deviations (R.S.Ds.) were 6.6% for Sb(III) and 7.1% for total Sb (c = 0.2 ng mL⁻¹, n = 7), respectively. The enrichment factor was 96. The developed method has been applied successfully to the determination of Sb(III) and total Sb in natural water samples.     

An ion-exchange method for speciation of antimony by flow injection electrothermal atomic absorption spectrometry

In this work, a simple preconcentration system, achieved by replacing the sample tip of the autosampler arm by a micro-column packed with Amberlite IRA-910 or silica gel chelating resin functionalised with 1,5-bis(di-2-pyridyl)methylene tbiocarbohydrazide (DPTH-gel), is developed for the determination of Sb(V) and total antimony, respectively. Different factors including pH of sample solution, ionic strength, concentration and volume of eluent, sample flow rate, sample loading time and matrix effects for preconcentration were investigated. The method has been applied to the determination of antimony species in different samples.     

An on-line flow-injection microwave-assisted mineralization and a precipitation/dissolution system for the determination of molybdenum in blood serum and whole blood by electrothermal atomic absorption spectrometry

An on-line flow injection (FI) precipitation–dissolution system with microwave-assisted sample digestion has been developed for the electrothermal atomic absorption spectrometry (ETAAS) determination of trace or ultratrace amounts of molybdenum in human blood serum and whole blood samples. After the exposure of the sample to microwave radiation, the on-line precipitation of molybdenum was achieved by the merging-zone of a 0.5-ml plug of sample with a plug of potassium ferrocyanide, which were carried downstream with a solution of 0.5 mol l⁻¹ of HNO₃. The interfering effects of iron and copper were minimized by the introduction of a flow of a 5% (w/v) sodium potassium tartrate (for iron) and 2% (w/v) of thiourea (for copper and zinc) in a 5% (v/v) ammonia and 2% (v/v) ammonium chloride solution previous to the precipitation reaction. The reddish-brown precipitate of molybdenyl ferrocyanide was collected on the walls of a knotted reactor. The precipitate was dissolved with the introduction of 1 ml of a 3.0 mol l⁻¹ NaOH solution and the best performance in terms of detection limit and precision was achieved when a sub-sample of 140 μl was collected in a capillary of a sampling arm assembly, to introduce 20 μl volumes into the atomizer by means of positive displacement with air through a time-based injector. A detection limit (3σ) of 0.1 μg Mo l⁻¹ using an aqueous standard solution was obtained. The method is quantitative and is applied over the range 0.2–20.0 μg Mo l⁻¹. The precision of the method evaluated by ten replicate analyses of aqueous standard solutions containing 0.5 and 1.0 μg Mo l⁻¹ was 2.8 and 3.1% (relative standard deviation, RSD) (for n=5), respectively. Whereas, the precision evaluated by five replicate analysis of a serum and a whole blood sample were 3.3 and 3.8% RSD. An enrichment factor of ca. 3.5 was achieved with the introduction of 0.5 ml aqueous standard solutions at a sample flow rate of 1.0 ml min⁻¹. Recoveries of spiked molybdenum in blood serum and whole blood were in the ranges 96–102 and 94–98%, respectively. The results obtained for two human whole blood certified reference materials were in good agreement with the indicative values.     

流动注射壳聚糖在线微柱预富集电热原子吸收光谱法测定痕量Cr(VI)

以天然高分子材料壳聚糖作在线预富集柱填料,流动注射与电热原子光谱联用测定痕量Cr(VI)。采样体积5.80mL,采样频率22样/h,富集倍数51倍,线性范围0.02μg/L～0.12μg/L,该方法的检出限(3s,n=11)0.69ng/L,相对标准偏差5.1%(CCr(VI)=0.10μg/L,n=11)。将该方法用于环境水样、茶叶样品和头发样品中Cr(VI)的测定,结果满意。     

流动注射-在线富集火焰原子吸收分光光度法测定痕量铅

本文报道在流动注射分析体系中用装有黄原脂棉的微型柱对溶液中Pb2 进行在线富集后,用3.0 mol/L盐酸洗脱柱上富集的Pb2 ,然后采用火焰原子吸收光谱法在线测定痕量Pb2 ,方法的线性范围为0.5～100μg/L。与未富集前相比,测定的灵敏度可提高65倍。方法用于环境水样中痕量Pb2 的测定,回收率在97.0%～102%之间,相对标准偏差小于4.0%,分析结果满意。     

在线还原富集火焰原子吸收光谱法测定环境水样中Cr(Ⅲ)和Cr(Ⅵ)的形态

采用单阀双阳离子交换树脂微柱并联，设计了双路采样逆向洗脱在线分离富集系统，该系统与原子吸收测量技术相结合，实现了在线分离富集-火焰原子吸收光谱法同时测定水中Cr(Ⅲ)和Cr(Ⅵ)，富集1min时，分析速度为60样/h，测定Cr(Ⅲ)和Cr(Ⅵ)的特征浓度分别为6．08μg/L和11．58μg/L(相当于1％吸收)，线性范围分别为0～1．0μg/mL和0～2．0μg/mL，对质量浓度为100μg/L的Cr(Ⅲ)和Cr(Ⅵ)测定的相对标准偏差分别为2．9％和3．0％、检出限分别为8．70和10．8μg/L。该法对实际水样加标回收率在94．5％～104．3％之间。     

Direct determination of arsenic and antimony in naphtha by electrothermal atomic absorption spectrometry with microemulsion sample introduction and iridium permanent modifier

This paper reports the determination of arsenic and antimony in naphtha by employing electrothermal atomic absorption spectrometry (ETAAS) as the analytical technique. In order to promote the direct determination of the analytes in the very volatile naphtha, the formation of a microemulsion with different surfactants (Triton X-100 and Brij-35) and different chemical modification strategies were tested. The results indicated that Triton X-100 is the best emulsification agent for naphtha in both As and Sb determination when it is employed at a concentration of 1% w/v in the microemulsion. Under these conditions, the microemulsion was stabile for at least 2 h. By using Brij-35 it was possible to achieve good stability only in the first 15 min. Among all chemical modification approaches investigated (Ir permanent modifier, W-Ir permanent modifier, and Pd modifier), the Ir permanent modifier provided better sensitivity for both analytes and allowed a higher pyrolysis temperature, which decreased the background signals at lower levels. Under the best conditions established in this work, an RSD of 4.6% (20 g L^–1) and a detection limit of 2.7 g L^–1 were observed for arsenic. For antimony, an RSD of 4.0% (20 g L^–1) and a detection limit of 2.5 g L^–1 were obtained. The accuracy of the procedure was assessed by analyzing spiked samples of naphtha from different origins.     

Preconcentration and determination of ultra trace amounts of arsenic(III) and arsenic(V) in tap water and total arsenic in biological samples by cloud point extraction and electrothermal atomic absorption spectrometry

A new approach for developing a cloud point extraction-electrothermal atomic absorption spectrometry has been described and used for determination of arsenic. The method is based on phase separation phenomenon of non-ionic surfactants in aqueous solutions. After reaction of As(V) with molybdate towards a yellow heteropoly acid complex in sulfuric acid medium and increasing the temperature to 55 °C, analytes are quantitatively extracted to the non-ionic surfactant-rich phase (Triton X-114) after centrifugation.To decrease the viscosity of the extract and to allow its pipetting by the autosampler, 100 μl methanol was added to the surfactant-rich phase. An amount of 20 μl of this solution plus 10 μl of 0.1% m/v Pd(NO₃)₂ were injected into the graphite tube and the analyte determined by electrothermal atomic absorption spectrometry.Total inorganic arsenic(III, V) was extracted similarly after oxidation of As(III) to As(V) with KMnO₄. As(III) was calculated by difference. After optimization of the extraction condition and the instrumental parameters, a detection limit (3σ_B) of 0.01 μg l⁻¹ with enrichment factor of 52.5 was achieved for only 10 ml of sample. The analytical curve was linear in the concentration range of 0.02-0.35 μg l⁻¹. Relative standard deviations were lower than 5%. The method was successfully applied to the determination of As(III) and As(V) in tap water and total arsenic in biological samples (hair and nail).     

Determination of antimony content in natural water by graphite furnace atomic absorption spectrometry after collection as antimony(III)-pyrogallol complex on activated carbon

Antimony(III) was preconcentrated on activated carbon (AC) as the antimony(III)–pyrogallol complex. Prior to the preconcentration, antimony(V) was reduced to antimony(III) with potassium iodide and ascorbic acid. The antimony adsorbed on the AC was determined by graphite furnace atomic absorption spectrometry as an AC suspension. The method was applied to differential determination of trace amounts of antimony in natural water.     

流动注射在线分离富集-电热原子吸收法测定地球化学样品中的痕量金、铂、钯

建立了流动注射在线同时分离富集，无火焰原子吸收法测定地球化学样品中金、铂、钯的分析方法。研究了联用技术并进行了吸附条件和解脱条件的优化实验。当采样频率为20样/h时，Au、Pt、Pd的富集倍数分别为43、37、41。Au、Pt、Pd的检出限(3σ)分别为5、16、9ng／L。将Au、Pt、Pd质量浓度分别为50、200、100ng／L的混合标准溶液平行测定7次，求得Au、Pt、Pd的相对标准偏差分别为3．6％、5．1％、4．7％。并对国家级标准样品进行了测定，其结果及精密度符合要求。     

流动注射在线分离浓集技术在原子吸收光谱分析中的应用

对流动注射在线分离浓度与原子吸收光谱连用技术及其应用作了综述。引用文献８６篇。     

Adsorption of antimony(III) and antimony(V) on bentonite: Kinetics, thermodynamics and anion competition

This research attempted to study the adsorption of Sb(III) and Sb(V) on bentonite using batch experiments. The effects of reaction time, temperature, initial Sb concentration, and competitive anions at different concentrations on the adsorption of Sb(III) and Sb(V) were investigated. Kinetic studies suggested that the adsorption equilibriums for both Sb(III) and Sb(V) were reached within 24 h. The desorption of Sb adsorbate on the bentonite was observed following Sb(III) adsorption, probably due to the oxidation of Sb(III) on the bentonite surface and subsequent desorption of Sb(V). In addition, oxidation of Sb(III) can occur in the solution medium also, which decreases the concentration of Sb(III) in the solution thereby driving the equilibrium in the direction of desorption from the surface. The adsorption data at three temperatures were successfully modeled using Langmuir (r² > 0.82) and Freundlich (r² > 0.99) isotherms. The thermodynamic parameters (ΔG⁰, ΔH⁰, and ΔS⁰) were calculated from the temperature dependence, suggesting that the adsorption process of Sb(III) is spontaneously exothermic, while the adsorption process of Sb(V) is spontaneously endothermic. Competitive anions such as , , and hardly affected the Sb(III) adsorption on bentonite, while and could compete with for adsorption sites. The competition between and on adsorption sites was presumably due to the formation of surface complexes and the surface accumulation or precipitation of on bentonite surface.     

Evaluation of a novel PTFE material for use as a means for separation and preconcentration of trace levels of metal ions in sequential injection (SI) and sequential injection lab-on-valve (SI-LOV) systems: Determination of cadmium(II) with detection by electrothermal atomic absorption spectrometry (ETAAS)

The operational characteristics of a novel poly(tetrafluoroethylene) (PTFE) bead material, granular Algoflon^®, used for separation and preconcentration of metal ions via adsorption of on-line generated non-charged metal complexes, were evaluated in a sequential injection (SI) system furnished with an external packed column and in a sequential injection lab-on-valve (SI-LOV) system. Employed for the determination of cadmium(II), complexed with diethyldithiophosphate (DDPA), and detection by electrothermal atomic absorption spectrometry (ETAAS), its performance was compared to that of a previously used material, Aldrich PTFE, which had demonstrated that PTFE was the most promising for solid-state pretreatments. By comparing the two materials, the Algoflon^® beads exhibited much higher sensitivity (1.6107 μg l⁻¹ versus 0.2956 μg l⁻¹ per integrated absorbance (s)), and better retention efficiency (82% versus 74%) and enrichment factor (20.8 versus 17.2), although a slightly smaller linear dynamic range (0.05-0.25 μg l⁻¹ versus 0.05-1.00 μg l⁻¹). Moreover, no flow resistance was encountered under the experimental conditions used. The results obtained on three standard reference materials were in good agreement with the certified values.     

Lead ultra-trace on-line preconcentration and determination using selective solid phase extraction and electrothermal atomic absorption spectrometry: applications in seawaters and biological samples

In this work, a new chelating resin [1,5-bis (2-pyridyl)-3-sulphophenyl methylene] thiocarbonohydrazide immobilised on aminopropyl-controlled pore glass (550 A; PSTH-cpg) was synthesised and packed in a microcolumn which replaced the sample tip of the autosampler arm. The system was applied to the preconcentration of lead. When microliters of 10% HNO3, which acts as elution agent, pass through the microcolumn, the preconcentrated Pb(II) is eluted and directly deposited in a tungsten-rhodium coated graphite tube. With the use of the separation and preconcentration step and the permanent modifiers, the analytical characteristics of the technique were improved. The proposed method has a linear calibration range from 0.012 to 10 ng ml(-1) of lead. At a sample frequency of 36 h(-1) with a 90 s preconcentration time, the enrichment factor was 20.5, the detection and determination limits were 0.012 and 0.14 ng ml(-1), respectively and the precision, expressed as relative standard deviation, was 3.2% (at 1 ng ml(-1)). Results from the determination of Pb in biological certified reference materials were in agreement with the certified values. Seawaters and other biological samples were analysed too.     

On-line flow injection solvent extraction for electrothermal atomic absorption spectrometry: Determination of nickel in biological samples

A flow injection (FI) on-line solvent extraction system for electrothermal atomic absorption spectrometry (ETAAS) was developed with nickel as a model trace element. The nickel pyrrolidine-dithiocarbamate chelate was extracted on line into isobutyl methyl ketone, which was delivered into the FI system by a peristaltic pump equipped with poly(tetrafluoroethylene) tubing. The organic phase was separated from the aqueous phase by a novel gravity phase separator with a small conical cavity, and stored in a collector tube, from which 50 μl organic concentrate was introduced into the graphite tube by an air flow. ETAAS determination of the analyte was performed in parallel with the extraction process. An enrichment factor of 25 was obtained in comparison with 50 μl direct introduction while achieving a detection limit of 4 ng l⁻¹ (3σ), and a precision of 1.5% relative standard deviation for 1.0 μg l⁻¹ nickel (n = 11). The proposed method was successfully applied to the determination of nickel in body fluids and other biological samples.     

Determination of Silver with On-Line Preconcentration Using Dithiozone Chelate and Carbon Nanotubes for Preconcentration with Detection by Flame Atomic Absorption Spectrometry

A novel flow injection system incorporating a micro-column packed with carbon nanotubes (CNTs) as an adsorbent has been applied to the on-line preconcentration of trace silver with detection by flame atomic absorption spectrometry. Silver is first chelated by dithizone (H₂Dz), then retained on the CNTs surface and afterward quantitatively eluted by methanol. Influencing parameters, including the concentration of reaction reagent, enrichment variables, and elution variables were investigated. The adsorption mechanisms of Ag-H₂Dz chelate retained onto the CNTs surface have also been studied. By loading 6.9 mL sample solution, a linear calibration graph is obtained within the range of 3–120 µg L^?1 with R of 0.9996, and a detection limit (3σ) of 0.8 µg L^?1 is achieved, along with a precision of 1.6% R.S.D. at the 30 µg L^?1 level (n = 7). The dynamic sorption capacity of CNTs for silver is 122 mg g^?1. The procedure is demonstrated by measurement of spike recovery in a series of water samples, giving rise to spike recoveries in the range of 96.8–99.7%.     

Cloud point extraction for the determination of As(III) in water samples by electrothermal atomic absorption spectrometry

Cloud point extraction was applied as a preconcentration step for electrothermal atomic absorption spectrometry (ETAAS) determination of As(III) in aqueous solutions. After complexation with ammonium pyrrolidinedithiocarbamate, the analyte was quantitatively extracted to the surfactant-rich phase in the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114) after centrifugation. 0.1 mol L⁻¹ HNO₃ in methanol was added to the surfactant-rich phase before ETAAS determination. The precision (R.S.D.) for 11 replicate determinations of 5.0 μg L⁻¹ of As(III) was 3.0%. The concentration factor, which is defined as the concentration ratio of the analyte in the final diluted surfactant-rich extract ready for ETAAS determination and in the initial solution, was 36 for As(III). The linear concentration range was from 0.1 to 20 μg L⁻¹. The developed method was applied to the determination of As(III) in lake water and river water.