Application of fast ultrasound water-bath assisted enzymatic hydrolysis--high performance liquid chromatography-inductively coupled plasma-mass spectrometry procedures for arsenic speciation in seafood materials

Enzymatic hydrolysis of seafood materials for isolating arsenic species (As(III), As(V), DMA and AsB) has been successfully performed by assisting the procedure with ultrasound energy (35 kHz) supplied by an ultrasound water-bath. The use of pepsin, as a proteolytic enzyme, under optimized operating conditions (pH 3.0, temperature 40 °C, enzyme to sample ratio of 0.3) led to an efficient assistance of the enzymatic process in a short period of time (from 4.0 to 30 min). The enzymatic extract was then subjected to a clean-up procedure based on ENVI-Carb™ solid phase extraction (SPE). An optimized anion exchange high performance liquid chromatography (HPLC) coupled to inductively coupled plasma-mass spectrometry (ICP-MS) permitted the fast separation (less than 15 min) of six different arsenic species (arsenite, As(III); arsenate, As(V); dimethylarsinic acid, DMA; and arsenobetaine, AsB; as well as monomethylarsonic acid, MMA; and arsenocholine, AsC) in a single run. Relative standard deviations (n = 11) of the over-all procedure were 7% for AsB and DMA, 11% for As(III) and 9% for MMA. HPLC–ICP-MS determinations were performed using aqueous calibrations covering arsenic concentrations of 0, 5, 10, 25, 100 and 200 μg L⁻¹ (expressed as arsenic) for As(III), As(V), MMA, DMA and AsC; and 0, 125, 250, 500, 750, 1000 and 2000 μg L⁻¹ (expressed as arsenic) for AsB. Germanium (5 μg L⁻¹) was used as an internal standard. Analytical recoveries from the anion exchange column varied from 96 to 105% (enzymatic digests spiked with low target concentrations), from 97 to 104% (enzymatic digests spiked with intermediate target concentrations), and from 98 to 103% (enzymatic digests spiked with high target concentrations). The developed method was successfully applied to two certified reference materials (CRMs), DORM-2 and BCR 627, which offer certified AsB and DMA contents, and also to different seafood samples (mollusks, white fish and cold water fish). Good agreement between certified and found AsB concentrations was achieved when analyzing both CRMs; and also, between certified and found DMA concentrations in BCR 627. In addition, the sum of the different arsenic species concentrations found in most of the analyzed samples was statistically similar to the assessed total arsenic concentrations after a total sample matrix decomposition treatment.     

Enzyme-assisted extraction and liquid chromatography mass spectrometry for the determination of arsenic species in chicken meat

Chicken is the most consumed meat in North America. Concentrations of arsenic in chicken range from μg kg⁻¹ to mg kg⁻¹. However, little is known about the speciation of arsenic in chicken meat. The objective of this research was to develop a method enabling determination of arsenic species in chicken breast muscle. We report here enzyme-enhanced extraction of arsenic species from chicken meat, separation using anion exchange chromatography (HPLC), and simultaneous detection with both inductively coupled plasma mass spectrometry (ICPMS) and electrospray ionization tandem mass spectrometry (ESIMS). We compared the extraction of arsenic species using several proteolytic enzymes: bromelain, papain, pepsin, proteinase K, and trypsin. With the use of papain-assisted extraction, 10 arsenic species were extracted and detected, as compared to 8 detectable arsenic species in the water/methanol extract. The overall extraction efficiency was also improved using a combination of ultrasonication and papain digestion, as compared to the conventional water/methanol extraction. Detection limits were in the range of 1.0–1.8 μg arsenic per kg chicken breast meat (dry weight) for seven arsenic species: arsenobetaine (AsB), inorganic arsenite (As^III), dimethylarsinic acid (DMA), monomethylarsonic acid (MMA), inorganic arsenate (As^V), 3-nitro-4-hydroxyphenylarsonic acid (Roxarsone), and N-acetyl-4-hydroxy-m-arsanilic acid (NAHAA). Analysis of breast meat samples from six chickens receiving feed containing Roxarsone showed the presence of (mean ± standard deviation μg kg⁻¹) AsB (107 ± 4), As^III (113 ± 7), As^V (7 ± 2), MMA (51 ± 5), DMA (64 ± 6), Roxarsone (18 ± 1), and four unidentified arsenic species (approximate concentration 1–10 μg kg⁻¹).     

Suitability of selective pressurized liquid extraction combined with gas chromatography-ion-trap tandem mass spectrometry for the analysis of polybrominated diphenyl ethers

A one-step extraction and clean-up method using pressurized liquid extraction (PLE) (selective PLE) combined with gas chromatography-ion-trap tandem mass spectrometry (GC-ITMS-MS) was evaluated for the analysis of polybrominated diphenyl ethers (from tri- to hepta-PBDEs) at low concentrations in fish and shellfish samples. To this end, the performance of an on-line PLE extraction/clean-up method and of a classical Soxhlet extraction and clean-up method using a multi-layer modified silica column were compared. The two sample treatment methods provided similar results, although an important reduction in the sample treatment time (40 min per sample) was achieved using the selective PLE method. In addition, the suitability of the PLE combined with GC-ITMS-MS method was evaluated by comparing the results obtained in the analysis of fish samples with those obtained by gas chromatography-high resolution mass spectrometry (GC-HRMS). Good agreement between both techniques was obtained with differences between the mean values of less than 16%. The selective PLE method coupled to GC-ITMS-MS produced accurate results for PBDE determination with low limits of detection (1.0-16.8 pg g⁻¹ wet weight) and quantification (3.1-51 pg g⁻¹ wet weight) as well as good precision (RSD < 16%). This method has been applied to the analysis of PBDEs in fish and shellfish samples collected at fish markets in Catalonia (NE Spain).     

Pressurized liquid extraction as a novel sample pre-treatment for trace element leaching from biological material

Pressurized liquid extraction (PLE), commonly used for organic compounds extraction, has been applied for trace element leaching from marine biological material in order to determine major and trace elements (Al, As, Cd, Co, Cu, Fe, Hg, Li, Mn, Pb, Se, Sr, V and Zn). The released elements by formic acid PLE have been evaluated by inductively coupled plasma-optical emission spectrometry (ICP-OES). Different variables, such as formic acid concentration, extraction temperature, static time, extraction steps, pressure, mean particle size and diatomaceous earth (DE) mass/sample mass ratio were simultaneously studied by applying an experimental design approach (Plackett-Burman design (PBD) and central composite design (CCD)). Results showed that the extraction temperature was statistically significant (confidence interval of 95%) for most of the elements (high metal releasing was achieved at high temperatures). In addition, formic acid concentration was also statistically significant (confidence interval of 95%) for metals such as Cd and Cu. Most of the metals can be extracted using the same PLE operating conditions (formic acid concentration of 1.0 M, extraction temperature at 125 °C, static time of 5 min, one extraction step, extraction pressure at 500 psi and DE mass/sample mass ratio of 2). Taking in mind PLE requirements at the optimised operating conditions (125 °C), a time of 6 min is needed to pre-heat the cell. Therefore, the PLE assisted multi-element leaching is completed after 12 min. Analytical performances, such as limits of detection and quantification, repeatability of the over-all procedure and accuracy, by analysing GBW-08571, DORM-2, DOLT-3 and TORT-2 certified reference materials, were finally assessed.     

Arsenic speciation in marine product samples: Comparison of extraction-HPLC method and digestion-cryogenic trap method

For the arsenic speciation in marine product samples, two types of pretreatment-analysis combination were compared. One is the combination of solvent extraction and high performance liquid chromatography (HPLC) followed by a highly sensitive arsenic detection, while the other is the combination of alkaline digestion and cryogenic trap (CT) method followed by a highly sensitive arsenic detection. For six certified reference materials (CRMs) of marine animal samples, the concentrations of arsenobetaine (AsB) obtained from the extraction-HPLC method were very consistent with those of trimethylated arsenic species measured by the digestion-CT method. For four seaweed samples, the determination of three arsenosugars (Sugar-1, Sugar-2, and Sugar-3) was favorably carried out by the extraction-HPLC method. Those seaweed samples were also subjected to the digestion-CT method, and the amounts of dimethylated arsenic species measured by the method were approximately equal to the sum of the amounts of dimethylarsinic acid (DMAA) and three arsenosugars (Sugar-1 + Sugar-2 + Sugar-3) obtained from the extraction-HPLC method.     

Selective pressurized liquid extraction of polybrominated diphenyl ethers in fish

A fast and simple method for the analysis of polybrominated diphenyl ethers (PBDEs) in fish samples was developed using a one-step extraction and clean-up by means of pressurized liquid extraction (PLE) combined with gas chromatography-ion trap tandem mass spectrometry (GC-ITMS-MS). The selective PLE method provided to obtain ready-to-analyse extracts without any additional clean-up step, using a sorbent as fat retainer inside the PLE cell. Several PLE operating conditions, such as solvent type, extraction temperature and time, number of cycles and type of fat retainer, were studied. Using Florisil as fat retainer, maximum recoveries of PBDEs (83-108%) with minimum presence of matrix-interfering compounds were obtained using a mixture of n-hexane:dichloromethane 90:10 (v/v) as solvent, an extraction temperature of 100 °C and a static extraction time of 5 min in combination with three static cycles. Quality parameters of the method were established using standards and fish samples. Limits of detection and quantification ranged from 10 to 34 pg g⁻¹ wet weight and between 34 and 68 pg g⁻¹ wet weight, respectively. In addition, good linearity (between 1 and 500 ng ml⁻¹) and high precision (RSD % < 15%) were achieved. The method was validated using the standard reference material SRM-1945 (whale blubber) and was then applied to the analysis of PBDEs in fish samples.     

A microwave-assisted sequential extraction of water and dilute acid soluble arsenic species from marine plant and animal tissues

This paper describes the use of dilute nitric acid for the extraction and quantification of arsenic species. A number of extractants (e.g. water, 1.5 M orthophosphoric acid, methanol-water and dilute nitric acid) were tested for the extraction of arsenic from marine biological samples, such as plants that have proved difficult to quantitatively extract. Dilute 2% (v/v) nitric acid was found to give the highest recoveries of arsenic overall and was chosen for further optimisation. The optimal extraction conditions for arsenic were 2% (v/v) HNO₃, 6 min⁻¹, 90 °C. Arsenic species were found to be stable under the optimised conditions with the exception of the arsenoriboses which degraded to a product eluting at the same retention time as glycerol arsenoribose. Good agreement was found between the 2% (v/v) HNO₃ extraction and the methanol-water extraction for the certified reference material DORM-2 (AB 17.1 and 16.2 μg g⁻¹, respectively, and TETRA 0.27 and 0.25 μg g⁻¹, respectively), which were in close agreement with the certified concentrations of AB 16.4 ± 1.1 μg g⁻¹ and TETRA 0.248 ± 0.054 μg g⁻¹.To preserve the integrity of arsenic species, a sequential extraction technique was developed where the previously methanol-water extracted pellet was further extracted with 2% (v/v) HNO₃ under the optimised conditions. Increases in arsenic recoveries between 13% and 36% were found and speciation of this faction revealed that only inorganic and simple methylated species were extracted.     

Simultaneous determination of arsenic and selenium species in fish tissues using microwave-assisted enzymatic extraction and ion chromatography-inductively coupled plasma mass spectrometry

A microwave-assisted enzymatic extraction (MAEE) method was developed for the simultaneous extraction of arsenic (As) and selenium (Se) species in fish tissues. The extraction efficiency of total As and Se and the stability of As and Se species were evaluated by analyzing DOLT-3 (dogfish liver). Enzymatic extraction using pronase E/lipase mixture assisted by microwave energy was found to give satisfactory extraction recoveries for As and Se without promoting interspecies conversion. The optimum extraction conditions were found to be 0.2 g of sample, 20 mg pronase E and 5 mg lipase in 10 mL of 50 mM phosphate buffer, pH 7.25 at 37 °C. The total extraction time was 30 min. The speciation analysis was performed by ion chromatography-inductively coupled plasma mass spectrometry (IC-ICP-MS). The accuracy of the developed extraction procedure was verified by analyzing two reference materials, DOLT-3 and BCR-627. The extraction recoveries in those reference materials ranged between 82 and 94% for As and 57 and 97% for Se. The accuracy of arsenic species measurement was tested by the analysis of BCR 627. The proposed method was applied to determine As and Se species in fish tissues purchased from a local fish market. Arsenobetaine (AsB) and selenomethionine (SeMet) were the major species detected in fish tissues. In the analyzed fish extracts, the sum of As species detected was in good agreement with the total As extracted. However, for Se, the sum of its species was lower than the total Se extracted, revealing the presence of Se-containing peptides or proteins.     

Non-chromatographic speciation of toxic arsenic in fish

A rapid, sensitive and economic method has been developed for the direct determination of toxic species of arsenic present in fish and mussel samples. As(III), As(V), dimethylarsinic acid (DMA), and monomethylarsonic acid (MMA) were determined by hydride generation-atomic fluorescence spectrometry using a series of proportional equations without the need of a chromatographic previous separation. The method is based on the extraction of arsenic species from fish through sonication with HNO₃ 3 mol l⁻¹ and 0.1% (m/v) Triton and washing of the solid phase with 0.1% (m/v) EDTA, followed by direct measurement of the corresponding hydrides in four different experimental conditions. The limit of detection of the method was 0.62 ng g⁻¹ for As(III), 2.1 ng g⁻¹ for As(V), 1.8 ng g⁻¹ for MMA and 5.4 ng g⁻¹ for DMA, in all cases expressed in terms of sample dry weight. The mean relative standard deviation values (R.S.D.) in actual sample analysis were: 6.8% for As(III), 10.3% for As(V), 8.5% for MMA and 7.4% for DMA at concentration levels from 0.08 mg kg⁻¹ As(III) to 1.3 mg kg⁻¹ DMA. Recovery studies provided percentages greater than 93% for all species in spiked samples. The analysis of SRM DORM-2 and CRM 627 certified materials evidenced that the method is suitable for the accurate determination of arsenic species in fish.     

Arsenic speciation in marine biological materials by LC-UV-HG-ICP/OES

Arsenic compounds have been extracted with methanol/water (1:1) from three Certified Reference Materials (CRMs): CRM 278 (mussel tissue), CRM 422 (cod muscle) and DORM-1 (dogfish muscle). The extracts obtained were analyzed by an LC-UV-HG-ICP/OES coupled system, which permits the one-line determination of arsenocholine, arsenobetaine, dimethylarsinate, monomethylarsonate, As(III) and AS(V) at concentration in the range of gl^–1. The main species found in all CRMs extracts was arsenobetaine (97.3% of total As in CRM 422, 89.5% of total As in DORM-1 and 22.2% of total As in CRM 278).     

Pressurized liquid extraction-assisted mussel cytosol preparation for the determination of metals bound to metallothionein-like proteins

The possibilities of pressurized liquid extraction (PLE) have been novelty tested to assist the cytosol preparation from wet mussel soft tissue before the determination of metals bound to metallothionein-like proteins (MLPs). Results obtained after PLE were compared with those obtained after a classical blending procedure for mussel cytosolic preparation. Isoforms MLP-1 (retention time of 4.1 min) and MLP-2 (retention time of 7.4 min) were separated by anion exchange high-performance liquid chromatography (HPLC) and the concentrations of Ba, Cu, Mn, Sr and Zn bound to MLP isoforms were directly measured by inductively coupled plasma-atomic emission spectrometry (ICP-OES) as a multi-element detector. The optimized PLE-assisted mussel cytosol preparation has consisted of one extraction cycle at room temperature and 1500 psi for 2 min. Since separation between the solid mussel residue and the extract (cytosol) is performed by the PLE system, the cytosol preparation method is faster than conventional cytosol preparation methods by cutting/blending using Ultraturrax or Stomacher devices.     

Evaluation of the arsenic binding capacity of plant proteins under conditions of protein extraction for gel electrophoretic analysis

As prerequisite for the investigation of arsenic-binding proteins in plants, the general influence of different extraction parameters on the binding behaviour of arsenic to the plant protein pool was investigated. The concentration of the extraction buffer affected the extraction yield both for proteins and for arsenic revealing an optimal buffer concentration of 5 mM Tris/HCl, pH 8. The addition of 1 or 2% (w/v) SDS to the extraction buffer produced a two- to threefold enhancement of the total protein extraction yield but strongly suppressed the simultaneous extraction of arsenic from 80 ± 8% extraction yield obtained without SDS to 48 ± 2% in presence of 2% (w/v) SDS. The arsenic binding capacity of the protein fraction obtained after extraction with Tris buffer and protein precipitation by trichloroacetic acid in acetone was estimated to be 1.4 ± 0.6% independently on the original spiking concentration of arsenic provided in the form of monomethylarsonate to the extracts. Due to the low total protein concentrations of the plant extracts that varied in the range from 75 to 412 μg mL⁻¹ depending on the extraction parameters, high arsenic concentrations of 263-1001 mg (kg protein mass)⁻¹ resulted for spiking concentrations of 10 mg As L⁻¹. The optimized protein isolation procedure was applied to plants grown under arsenic exposure and revealed a similar arsenic binding capacity as for the spiked protein extracts.     

Development of an accurate procedure for the determination of arsenic in fish tissues of marine origin by inductively coupled plasma mass spectrometry

High accuracy procedures for the determination of arsenic are needed for assigning reference values to certified reference materials (CRMs). There are a number of problems associated with the determination of total arsenic by inductively coupled plasma–mass spectrometry. Arsenobetaine (AsB) (the major species in fish) gives an enhanced response (9%) when compared to inorganic arsenic(V) and is very difficult to decompose. Chloride causes interference at m/z 75 by the formation of ArCl⁺ and chloride levels can be significant in marine fish. Also residual carbon in digests can lead to enhancement of arsenic signals by charge transfer effects. This can easily lead to erroneous quantification when compared to standards that do not contain carbon.This newly developed procedure overcomes these issues by complete mineralisation of the matrix leaving insignificant amounts of residual carbon and by removal of chlorine by evaporation. A detection limit of 30 ng/g was achieved. Recoveries for the following CRMs: DORM 2 100.1 ± 4.3%, SRM1548 96.1 ± 4.6%, BCR 422 103.6 ± 6.2% and SRM2976 105.9 ± 6.2% were obtained. The digestion procedure uses open vessel wet digestion with a mixture of sulfuric and nitric acid held at 300 °C. The decomposition of AsB was confirmed by speciation analysis of the digest. Carbon (m/z 13) was monitored to demonstrate the efficiency of the digestion. Instrumentation for the reduction of ArCl⁺ interference was not required and this view is supported by the recovery data. Measurements were performed by external calibration using tellurium as an internal standard.     

Comparison of ultrasonic and pressurized liquid extraction for the analysis of polycyclic aromatic compounds in soil samples by gas chromatography coupled to tandem mass spectrometry

A pressurized liquid extraction (PLE) method has been optimized for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil samples and it was compared with ultrasonic extraction. The extraction step was followed by gas chromatography-triple quadrupole mass spectrometry (GC-QqQ-MS/MS) analysis. Parameters such as type of solvent, extraction time, extraction temperature and number of extractions were optimized. There were no significant differences among the two extraction methods although better extraction efficiencies were obtained when PLE was used, minimizing extraction time and solvent consumption. PLE procedure was validated, obtaining limits of detection (LODs) ranging from 0.02 to 0.75 μg kg⁻¹ and limits of quantification (LOQs) ranging from 0.07 to 2.50 μg kg⁻¹ for the selected PAHs. Recoveries were in the range of 59-110%, except for naphthalene, which was the most volatile PAH. Finally, the method was applied to real soil samples from Southeast of Spain. PAHs concentrations were low, and phenanthrene, pyrene, fluorene, benzo[a]pyrene and chrysene were the most frequently detected analytes in the samples.     

Pressurized liquid extraction of isoflavones from soybeans

Isoflavone derivatives from freeze-dried soybeans were extracted by pressurized liquid extraction (PLE) and determined by reverse-phase high performance liquid chromatography (HPLC) with both photo diode array and mass spectrometry (MS) detection. Both real and spiked samples were used in the development of the method.Several extraction solvents (methanol (MeOH) and ethanol (EtOH), 30-80% in water and water), temperatures (60-200 °C), pressures (100-200 atm), as well as the sample size (0.5-0.05 g) and cycle length (5-10 min) were studied for the optimization of the extraction protocol. The optimized extraction conditions for quantitative recoveries were: 0.1 g of sample, 100 °C, three (7 min) static extraction cycles and ethanol 70% as extracting solvent. The stability of the isoflavones during the PLE was also determined. Under PLE conditions, degradation of malonyl glucoside forms of the isoflavones takes place using temperatures higher than 100 °C whereas degradation of glucosides takes place above 150 °C. Using the optimized protocol, isoflavones can be extracted from freeze-dried soybeans without degradation.     

Pressurised membrane-assisted liquid extraction of UV filters from sludge

A method for the determination of 11 UV-filter compounds in sludge has been developed and evaluated. The procedure includes the use of non-porous polymeric membranes in combination with pressurised liquid extraction (PLE). Firstly, the solid sample, wetted with the extraction solvent, was enclosed into tailor-made bags prepared with low density polyethylene. Secondly, these packages were submitted to a conventional PLE (70 °C, 4 cycles of 5 min static time). Finally, the analytes were determined by liquid chromatography–atmospheric pressure photoionisation–tandem mass spectrometry. The main advantage of this procedure is the reduction of time, solvent and labour effort ought to the combination of extraction and clean-up in a single step. Although the extraction is not quantitative (thus, standard addition is recommended for quantification) selectivity is clearly gained using the membrane as a consequence of the differences of permeation and transport through the membrane between the analytes and other sample matrix components. The optimised protocol provides limits of detection ranging from 0.3 ng g⁻¹ (ethylhexyl dimethyl p-aminobenzoate (OD-PABA)) to 25 ng g⁻¹ (ethylhexyl triazone (EHT)) with only 0.5 g of sludge sample. All the studied UV filters were found in the samples at concentration levels between 1.4 and 2479 ng g⁻¹, emphasising the high adsorption potential of this kind of environmental pollutants onto solid samples such as sludge. Also, this method has permitted the determination of seven of the studied UV filters in sludge samples for the first time.     

Inductively coupled plasma mass spectrometry: Application to the determination of arsenic species

The application of ion-pair reversed phase chromatography (HPLC) and inductively coupled plasma mass spectrometry to the determination of six species of arsenic is described: arsenious acid (As^III), arsenic acid (As^V), monomethylarsinic acid (MMA), dimethylarsinic acid (DMA), arsenocholine (AsC) and arsenobetaine (AsB) in marine biota and in natural fresh water. The coupling conditions of HPLC-ICP-MS are given and also the evaluation of the extraction procedure applied to determine these species in marine organisms. The limits of detection are between 6 and 25 g.l^–1.     

Evaluation of surfactant assisted pressurized liquid extraction for the determination of glycyrrhizin and ephedrine in medicinal plants

Surfactant assisted pressurized liquid extraction (PLE) with a laboratory made system was applied for the extraction of glycyrrhizin in Radix glycyrrhizae/liquorice and ephedrine in Ephedra sinica. The proposed system set-up for this current work was simpler as no heating and back pressure regulator was required. Extraction with surfactant assisted PLE was carried out dynamically at a flow of 1.5 mL min⁻¹, at room temperature, under an applied pressure of 10-20 bar with an extraction time of 45-50 min. The extraction efficiencies of the proposed method using surfactants such as sodium dodecyl sulfate (SDS) and Triton X-100 were compared with sonication using organic solvent for different batches of medicinal plants materials. For the determination of glycyrrhizin in R. glycyrrhizae, the extraction efficiencies of surfactant assisted PLE with SDS and Triton X-100 was observed to be comparable with sonication. The method precision was found to vary from 1.6 to 2.6% (R.S.D., n = 6) on different days. For ephedrine in E. sinica, surfactant assisted PLE with SDS was found to give higher extraction efficiencies compared to Triton X-100. The overall method precision for surfactant assisted PLE with SDS for ephedrine in E. sinica was found to vary from 1.5 to 4.1% (R.S.D., n = 6) on different days. The marker compounds present in the various medicinal plant extracts were determined by gradient elution HPLC. Our data showed the possibility of PLE at room temperature and the advantages of eliminating the use of organic solvents in the extraction process.     

Pressurized liquid extraction versus other extraction techniques in micropreparative isolation of pharmacologically active isoflavones from Trifolium L. species

As a new sample preparation technique, pressurized liquid extraction (PLE), in combination with reversed-phase liquid chromatography (RP-LC) and photodiode-array (PDA) detection were used for the isolation and determination of phytoestrogenic isoflavones in hydrolyzed extracts obtained from aerial parts of five Trifolium L. (clover) species. To optimize the effectiveness of PLE procedure, variable extraction parameters: methanol and acetone (or their 75% aqueous solutions), as extraction solvents, temperatures (75, 100 and 125 °C) and the changeable number of static extraction cycles were tested. Additionally, two other micropreparative techniques: ultrasound-assisted extraction (UAE), and conventional solvent extraction (CSE), under optimized conditions, were also used and compared. Optimum extraction efficiency, expressed in the highest yield of biochanin A, formononetin, daidzein and genistein from plant material, with PLE, using methanol-water (75:25, v/v) as an extraction solvent, an oven temperature of 125 °C and three 5-min static extraction cycles, was obtained.     

Arsenic speciation in edible alga samples by microwave-assisted extraction and high performance liquid chromatography coupled to atomic fluorescence spectrometry

Twelve commercially available edible marine algae from France, Japan and Spain and the certified reference material (CRM) NIES No. 9 Sargassum fulvellum were analyzed for total arsenic and arsenic species. Total arsenic concentrations were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) after microwave digestion and ranged from 23 to 126 μg g⁻¹. Arsenic species in alga samples were extracted with deionized water by microwave-assisted extraction and showed extraction efficiencies from 49 to 98%, in terms of total arsenic. The presence of eleven arsenic species was studied by high performance liquid chromatography–ultraviolet photo-oxidation–hydride generation atomic–fluorescence spectrometry (HPLC–(UV)–HG–AFS) developed methods, using both anion and cation exchange chromatography. Glycerol and phosphate sugars were found in all alga samples analyzed, at concentrations between 0.11 and 22 μg g⁻¹, whereas sulfonate and sulfate sugars were only detected in three of them (0.6-7.2 μg g⁻¹). Regarding arsenic toxic species, low concentration levels of dimethylarsinic acid (DMA) (<0.9 μg g⁻¹) and generally high arsenate (As(V)) concentrations (up to 77 μg g⁻¹) were found in most of the algae studied. The results obtained are of interest to highlight the need to perform speciation analysis and to introduce appropriate legislation to limit toxic arsenic species content in these food products.