阴阳离子双隔膜三室电解槽电渗析处理垃圾渗滤液

采用阴阳离子双隔膜三室电解槽,将电渗析技术与Ｆｅｎｔｏｎ试剂法结合,去除垃圾渗滤液中氨氮和ＣＯＤ_Ｃｒ。垃圾渗滤液中的氨氮通过电渗析技术富集到阴极液中,随后用化学沉淀法加以去除。同时,在铁阳极上生成的Ｆｅ^２＋离子,与滴加入阳极液中的Ｈ_２Ｏ_２反应生成Ｆｅｎｔｏｎ试剂,降解有机物,降低ＣＯＤ_Ｃｒ。实验结果表明,模拟废水中的氨氮透过率达８０％,垃圾渗滤液中氨氮浓度和ＣＯＤ_Ｃｒ由原来的１９８２和２２４８ ｍｇ／Ｌ分别降至２００和１２７ ｍｇ／Ｌ。     

A simplified version of the total kjeldahl nitrogen method using an ammonia extraction ultrasound-assisted purge-and-trap system and ion chromatography for analyses of geological samples

The total Kjeldahl nitrogen (TKN) method was simplified by using a manifold connected to a purge-and-trap system immersed into an ultrasonic (US) bath for simultaneous ammonia (NH₃) extraction from many previously digested samples. Then, ammonia was collected in an acidic solution, converted to ammonium (NH₄⁺), and finally determined by ion chromatography method. Some variables were optimized, such as ultrasonic irradiation power and frequency, ultrasound-assisted NH₃ extraction time, NH₄⁺ mass and sulfuric acid concentration added to the NH₃ collector flask. Recovery tests revealed no changes in the pH values and no conversion of NH₄⁺ into other nitrogen species during the irradiation of NH₄Cl solutions with 25 or 40 kHz ultrasonic waves for up to 20 min. Sediment and oil free sandstone samples and soil certified reference materials (NCS DC 73319, NCS DC 73321 and NCS DC 73326) with different total nitrogen concentrations were analysed. The proposed method is faster, simpler and more sensitive than the classical Kjeldahl steam distillation method. The time for NH₃ extraction by the US-assisted purge-and-trap system (20 min) was half of that by the Kjeldahl steam distillation (40 min) for 10 previously digested samples. The detection limit was 9 μg g⁻¹ N, while for the Kjeldahl classical/indophenol method was 58 μg g⁻¹ N. Precision was always better than 13%. In the proposed method, carcinogenic reagents are not used, contrarily to the indophenol method. Furthermore, the proposed method can be adapted for fixed-NH₄⁺ determination.     

Thermodynamic properties on quaternary aqueous solutions of chlorides charge-type 1-1*2-1*2-1: XCl + MgCl2 + CaCl2 + H2O with (X ≡ Na; NH4)

In this investigation, the quaternary aqueous solutions of chlorides charge-type 1-1*2-1*2-1 with a cation (Na⁺; NH₄⁺; Mg²⁺; Ca²⁺) have been studied using the hygrometric method at 298.15 K. The water activities of the systems NH₄Cl + MgCl₂ + CaCl₂ + H₂O and NaCl + MgCl₂ + CaCl₂ + H₂O are measured at total molalities from 0.60 mol kg⁻¹ to saturation for different ionic-strength fractions NH₄Cl or NaCl, y = 0.20, 0.50, 0.80, and z ratio ionic-strength for other solutes, with z = 0.20, 0.50 and 0.80 for each y. The obtained data allow the deduction of osmotic coefficients.     

Ion-exclusion chromatography with the direct UV detection of non-absorbing inorganic cations using an anion-exchange conversion column in the iodide-form

An ion-exclusion chromatographic method for the direct UV detection of non-absorbing inorganic cations such as sodium (Na⁺), ammonium (NH₄⁺) and hydrazine (N₂H₅⁺) ions was developed by connecting an anion-exchange column in the I⁻-form after the separation column. For example, NH₄⁺ is converted to a UV-absorbing molecule, NH₄I, by the anion-exchange column in the I⁻-form after the ion-exclusion separation on anion-exchange column in the OH⁻-form with water eluent. As a result, the direct UV detection of Na⁺, NH₄⁺ and N₂H₅⁺ could be successfully obtained as well as the well-resolved separation. The calibration graphs of the analyte cations detected with UV at 230 nm were linear in the range of 0.001-5.0 mM. The detection limits at S/N = 3 of the cations were below 0.1 μM. This method was applied to real water analysis, the determination of NH₄⁺ in river and rain waters, or that of N₂H₅⁺ in boiler water, with the satisfactory results. This could be applied also to low- or non-absorbing anions such as fluoride or hydrogencarbonate ions by the combination of a weakly acidic cation-exchange resin in the H⁺-form as the separation column and the anion-exchange conversion column.     

Thermodynamics of aqueous solutions of poly ethylene glycol di-methyl ethers in the presence or absence of ammonium phosphate salts

Precise measurements of density and sound velocity at different temperatures ranging from 283.15 to 308.15 K for solutions of PEGDME250, PEGDME500 and PEGDME2000 in water and of PEGDME500 in aqueous solutions of 0.500 mol kg⁻¹ ammonium di-hydrogen phosphate ((NH₄)H₂PO₄) and di-ammonium hydrogen phosphate ((NH₄)₂HPO₄), binodal curves at temperature ranges 293.15-318.15 K for the aqueous PEGDME500 + (NH₄)₂HPO₄, PEGDME500 + (NH₄)₃PO₄, PEGDME2000 + (NH₄)H₂PO₄, PEGDME2000 + (NH₄)₂HPO₄, PEGDME2000 + (NH₄)₃PO₄ and PPG400 + (NH₄)₂HPO₄ two-phase systems, and liquid-liquid equilibrium data at temperature ranges 298.15-318.15 K for the aqueous PEGDME500 + (NH₄)₂HPO₄ and PEGDME2000 + (NH₄)₂HPO₄ two-phase systems have been taken. From the experimental density and sound velocity data, the apparent specific volume, excess specific volume, isentropic compressibility and isentropic compressibility deviation values have been determined and the effect of temperature, charge on the anion of electrolytes and molar mass of PEGDME on the volumetric and compressibility properties of the investigated polymer solutions as well as on the salting-out effect of PEGDMEs produced by ammonium phosphate salts has been studied.     

Ammonium-Nitrogen Recovery from Wastewater by Struvite Crystallization Technology

Struvite crystallization is one of the sustainable approaches for recovering ammonium nitrogen (NH₄-N) from wastewater in the form of a valuable material, in parallel with improving wastewater treatment efficiency. Focusing on NH₄-N recovery, this review discusses the factors influencing struvite crystallization including the effect of foreign elements. It is shown that more than 95% of NH₄-N could be recovered in the form of struvite, a magnesium-ammonium phosphate (MAP) salt, from some kinds of wastewater. This review emphasizes the role of utilizing alternative sources of Mg and P in improving the process sustainability. Additionally, it also explains how the MAP precipitation process could result with significant reduction of other pollutants contributing to total organic carbon, of color and turbidity, which support MAP integration with other treatment methods. The main options of lowering MAP recovery cost are presented; it was shown that applying low-cost materials of both Mg and P could save more than 65% of the process’s cost. Finally, the future research directions to improve NH₄-N recovery are pointed out.     

Benefits of near-infrared spectroscopy for characterization of selected organo-montmorillonites

The potential of near infrared (NIR) spectroscopy in characterization of organically modified clay minerals is introduced. Selected organo-clays, possibly perspective fillers in clay polymer nanocomposites, were prepared from Na-montmorillonite and different surfactants containing octylammonium chain(s), hexadecylammonium chain(s) or a benzene ring with or without a reactive double bond. Based on the stretching (ν) and bending (δ) vibrations observed in the middle IR (MIR) region, the first overtone (2νXH) and combination (ν + δ)XH modes of XH groups (X = O, C, N) are identified. The effect of larger alkylammonium cations on the vibrations of Si-O and OH bonds in montmorillonite layers is observed. The changes in the intensity of the (ν + δ)H₂O band near 5250 cm⁻¹ allows for comparison of the amount of water adsorbed on the montmorillonite surface. The water content decreases with the size of the organic cation reflecting increasing hydrophobicity of the montmorillonite surface. The NIR region shows the 2νCH₃ and 2νCH₂ bands in the 5900-5500 cm⁻¹ region, an upward shift is observed for the complex band due to 2νCH(Ar) of aromatic benzene ring. The NIR spectra are extremely useful in identification of NH₂⁺, NH⁺ and vinyl groups, which are difficult to recognize in the MIR spectra of organo-clays due to overlapping with other absorption bands. The intense bands corresponding to overtones and combination vibrations of NH₃⁺ and NH₂⁺ groups are found in the 6600-6050 cm⁻¹ and 5000-4600 cm⁻¹ regions, the (ν + δ)NH⁺ is unambiguously identified near 4750 cm⁻¹. The characteristic band assigned to 2νCH₂ in H₂CC is detected near 6130 cm⁻¹.     

A simple and rapid visual method for the determination of ammonia nitrogen in environmental waters using thymol

Simple visual and spectrophotometric methods for the determination of ammonia nitrogen in water are proposed, based on the color development of indothymol blue formed between ammonia and thymol. The color development was accelerated by nitroprusside to complete in 3 min. This color development is remarkably rapid compared with that of the other conventional methods with indothymol blue and indophenol blue. The concentration range of ammonia nitrogen spectrophotometrically determined was 0.04–1.2 mg/L NH₄-N. The absorbance per 1 μg NH₄-N was 0.0215 (molar absorptivity = 1.51 × 10⁴) at 690 nm. The visual method not using any instrument as an in situ method in field works was developed based on the optimum conditions for the established spectrophotometric method. This visual method was successfully applied to the determination of ammonia nitrogen in environmental waters.     

Preparation of Sorbents Containing Straetlingite Phase from Zeolitic By-Product and Their Performance for Ammonium Ion Removal

In this study, straetlingite-based sorbents were used for NH₄⁺ ion removal from a synthetic aqueous solution and from the wastewater of an open recirculation African catfish farming system. This study was performed using column experiments with four different filtration rates (2, 5, 10, and 15 mL/min). It was determined that breakthrough points and sorption capacity could be affected by several parameters such as flow rate and mineral composition of sorption materials. In the synthetic aqueous solution, NH₄⁺ removal reached the highest sorption capacity, i.e., 0.341 mg/g with the S30 sorbent at a filtration rate of 10 mL/min and an initial concentration of 10 mg/L of NH₄⁺ ions. It is important to emphasize that, in this case, the Ce/C0 ratio of 0.9 was not reached after 420 min of sorption. It was also determined that the NH₄⁺ sorption capacity was influenced by phosphorus. In the wastewater, the NH₄⁺ sorption capacity was almost seven times lower than that in the synthetic aqueous solution. However, it should be highlighted that the P sorption capacity reached 0.512 mg/g. According to these results, it can be concluded that straetlingite-based sorbents can be used for NH₄⁺ ion removal from a synthetic aqueous solution, as well as for both NH₄⁺ and P removal from industrial wastewater. In the wastewater, a significantly higher sorption capacity of the investigated sorbents was detected for P than for NH₄⁺.     

Determination of water-soluble inorganic and organic species in atmospheric fine particulate matter

The use of ion chromatography (IC) in conjunction with ultrasonic extraction is described for the routine analysis of water-soluble major inorganic ions and organic acids in atmospheric fine particles (PM_2.5). Both the extraction method and the IC analysis were validated using NIST SRM 1648 (urban particulate matter). In addition, the reliability of the IC method was established by intercomparison of results obtained with those from suitable alternative analytical techniques (atomic absorption spectrometry (AAS), proton-induced X-ray emission (PIXE) spectrometry, and UV-Visible spectrophotometry). The validated IC method was successfully applied for field monitoring of PM_2.5 particles collected in Singapore over an extended period of time. The IC analysis revealed that the concentrations of individual ions were in the order, SO₄²⁻ > NH₄⁺ > NO₃⁻ > Na⁺ > K⁺ > Cl⁻, respectively. Among the major ionic components, SO₄²⁻ contributed 50% to the measured water-soluble aerosol mass followed by NH₄⁺ (16.5%) and NO₃⁻ (9.0%). The cations Na⁺, K⁺, Mg²⁺, and Ca²⁺ accounted for 24% of the total water-soluble mass. The IC analysis was performed to quantify the organic acids, which typically account for a small fraction of water-soluble organic compounds in PM_2.5. Oxalate was found to be the dominant species among the organic acids measured in this work.     

A new tool for inorganic nitrogen speciation study: simultaneous determination of ammonium ion, nitrite and nitrate by ion chromatography with post-column ammonium derivatization by Nessler reagent and diode-array detection in rain water samples

The paper presents a new method for a simultaneous determination of inorganic nitrogen species in the oxidized (NO₂⁻, NO₃⁻) and reduced (NH₄⁺) form in rain water samples. The method is based on a system of nitrogen species separation employing ion exchange and diode-array detection. The ions are separated in a strong ion-exchanger, nitrites and nitrates are determined directly at 208 and 205 nm, respectively, while the ammonium ions are determined in the column hold-up time after a post-column derivatization by the Nessler reagent, at 425 nm. The use of a diode-array detector permits a simultaneous identification of the inorganic nitrogen species in 8 min. The detection limits obtained are: NO₂⁻, 0.1 mg L⁻¹; NO₃⁻, 0.05 mg L⁻¹; NH₄⁺, 1 mg L⁻¹. The method proposed has been successfully used for speciation analysis of inorganic nitrogen in precipitation.     

Determination of nitrogen in hydrolyzed protein formulations by continuous vapour phase FTIR

An on-line system with vapour generation (VG) and Fourier transform infrared (FTIR) spectrometric detection has been developed for the determination of free ammonium and organic nitrogen in agrochemical formulations containing hydrolyzed proteins. Commercial samples were digested, in batch mode, with sulphuric acid and the obtained solution was alkalinized on-line to transform the NH₄⁺ to NH₃ that was continuously monitored by FTIR. Free ammonium was determined in the same system after simple dilution of undigested samples with water. Different gas phase separators were assayed in order to introduce gaseous NH₃ into a home made IR gas cell of 10 cm pathlength, where the corresponding FTIR spectra were acquired by accumulating 10 scans per spectrum. The 967.0 cm⁻¹ band was used for the quantification of ammonia. The figures of merit of the proposed method involve a linear range up to 100 mg L⁻¹, a limit of detection (3σ) of 1.4 mg L⁻¹ of N, a limit of quantification (10σ) of 4.8 mg L⁻¹ of N, a precision (R.S.D.) of 3.0% for 10 replicate determinations of a 10.0 mg L⁻¹ of N and a sample measurement frequency of 60 h⁻¹. The method was successfully applied to the determination of free ammonium and total N in commercial amino acid formulations and results compare well with those obtained by the Kjeldhal method.     

Syntheses and characterization of ANi(AsF6)3 (A = H3O, O2, NO, NH4, K, Rb, and Cs) compounds

ANi(AsF₆)₃ (A = O₂⁺, NO⁺, NH₄⁺) compounds could be prepared by reaction between corresponding AAsF₆ salts and Ni(AsF₆)₂. When mixtures of AF (A = Li, Na, K, Rb, Cs) and NiF₂ are dissolved in aHF acidified with an excess of AsF₅ the corresponding AAsF₆ and Ni(AsF₆)₂ were formed in situ. For A = Li and Na only mixtures of AAsF₆ and Ni(AsF₆)₂ were obtained, while for A = K, Rb and Cs, the final products were ANi(AsF₆)₃ (A = K-Cs) compounds contaminated with AAsF₆ (A = K-Cs) and Ni(AsF₆)₂.ANi(AsF₆)₃ (A = H₃O⁺, O₂⁺, NO⁺, NH₄⁺ and K⁺) compounds are structurally related to previously known H₃OCo(AsF₆)₃. The main features of the structure of these compounds are rings of NiF₆ octahedra sharing apexes with AsF₆ octahedra connected into infinite tri-dimensional network. In this arrangement cavities are formed where single charged cations are placed.In O₂Ni(AsF₆)₃ the vibrational band belonging to O₂⁺ vibration is found at 1866 cm⁻¹, which is according to the literature data one of the highest known values, and it is only 10 cm⁻¹ lower than the value for free O₂⁺.     

Column preconcentration of mercury as HgI4 using methyltrioctylammonium chloride-naphthalene adsorbent with subsequent anodic stripping-differential pulse voltammetric determination

A sensitive and selective preconcentration method has been developed for mercury using naphthalene-methyltrioctylammonium chloride (Aliquat 336s) as an adsorbent. Mercury as HgI₄²⁻ was retained by the adsorbent in the column at a flow rate of 1 ml min⁻¹. The column was washed by a solution of sodium tetraphenylborate and sodium iodide to elute the adsorbed mercury. The eluents were collected in a 10 ml volumetric flask and diluted to the mark with water, transferred to a voltammetric cell and anodic stripping-differential pulse voltammetry was performed. Preconcentration factors of 40 and 80 could be achieved when using a 10 and 5 ml voltammetric cell, respectively. The calibration graph was linear in the range of 1.2-8.7 ng ml⁻¹ Hg(II) in the initial solution with r=0.9998 (n=6) and the 3 s detection limit was 0.13 ng ml⁻¹ when using a 10 ml cell. The relative standard deviation for eight replicate measurements of 1.2, 5.0 and 8.7 ng ml⁻¹ of Hg(II) in the initial solution was 0.51, 0.71 and 0.80%, respectively. The proposed method was successfully applied to determination of mercury in natural waters, wastewater and synthetic samples.     

Capillary electrophoretic determination of ammonia using headspace single-drop microextraction

A new method involving headspace single-drop microextraction (SDME) and capillary electrophoresis (CE) is developed for the preconcentration and determination of ammonia (as dissolved NH₃ and ammonium ion). An aqueous microdrop (5 μL) containing 1 mmol/L H₃PO₄ and 0.5 mmol/L KH₂PO₄ (as internal standard) was used as the acceptor phase. Common experimental parameters (sample and acceptor phase pH, extraction temperature, extraction time) affecting the extraction efficiency were investigated. Proposed SDME-CE method provided about 14-fold enrichment in about 20 min. The calibration curve was linear for concentrations of NH₄⁺ in the range from 5 to 100 μmol/L (R² = 0.996). The LOD (S / N = 3) was estimated to be 1.5 μmol/L of NH₄⁺. Such detection sensitivity is high enough for ammonia determination in common environmental and biological samples. Finally, headspace SDME was applied to determine ammonia in human blood, seawater and milk samples with spiked recoveries in the range of 96-107%.     

A portable and low cost equipment for flow injection chemiluminescence measurements

A compact, reliable and low cost flow injection chemiluminescence system is described. The flow system consists of a set of solenoid micro-pumps that can dispense reproductive micro-volumes of solutions. The luminometer was based on a coiled cell constructed from polyethylene tubing that was sandwiched between two large area photodiodes. The whole equipment costs about US$ 750 and weights ca. 3 kg. Equipment performance was evaluated by measuring low concentrations of hydrogen peroxide by oxidation of luminol and for the determination of ammonium, based on its inhibition of the luminescence provided by the reaction of luminol and sodium hypochlorite. Linear responses were achieved within 1.0-80 μmol L⁻¹ H₂O₂ and 0.6-60 μmol L⁻¹ NH₄⁺ with detection limits estimated as 400 nmol L⁻¹ H₂O₂ and 60 nmol L⁻¹ NH₄⁺ at the 99.7% confidence level. Coefficients of variation were 1.0 and 1.8%, estimated for 20 μmol L⁻¹ H₂O₂ and 15 μmol L⁻¹ NH₄⁺ (n = 20), respectively. Reagent consumption of 55 μg luminol, effluent volume of 950 μL per determination and sampling rate of 120 samples per hour were also achieved.     

Alkyl and dialkylammonium tetrafluoroborate catalyzed cis-trans isomerization of 1,3,5-trimethyl-1,3,5-triphenylcyclotrisiloxane

Alkyl and dialkylammonium tetrafluoroborate promoted cis-trans isomerization of 1,3,5-trimethyl-1,3,5-triphenylcyclotrisiloxane (1) in DMSO-d₆ were studied. The isomerization equilibrium constant K are within the range of 3.74-3.30 from 22 to 47 °C. Thermodynamic parameters of ΔH° and ΔS° for the isomerization were −0.95 kcal/mol and −0.59 cal/mol-K respectively. The isomerization rate is first order in [cis-1] and second order in [R_nNH_4−nBF₄]. Both components of R_nNH_4−n⁺ and BF₄⁻ are essential for the catalytic cis-trans isomerization. The catalytic strength follows the decreasing order of ⁺H₃N(CH₂)₆NH₃⁺>n-C₈H₁₇NH₃⁺>n-C₁₆H₃₃NH₃⁺>Me₃CNH₃⁺>PhCH₂NH₃⁺>Et₂NH₂⁺?Ph₂CHNH₃⁺, Et₃NH⁺. Inversion region was observed in the plot of ln(k_f/T) versus (1/T) with the ceiling located at around 38 °C. The positive activation enthalpy of 9 kcal/mol was estimated at 22-32 °C. The activation enthalpy turns to be slightly negative at T>38 °C.     

Synthesis, characterization and application of a novel mercapto- and amine-bifunctionalized silica for speciation/sorption of inorganic arsenic prior to inductively coupled plasma mass spectrometric determination

A bifunctional sorbent, (NH₂ + SH)silica, containing both amine and mercapto functionalities was prepared by modification of silica gel with 3-(triethoxysilyl)propylamine and (3-mercaptopropyl)trimethoxysilane. In addition to the bifunctional sorbent, silica gel was modified individually with the functional mercapto- and amino-silanes, and the mono-functional sorbents, namely (SH)silica and (NH₂)silica, were also mechanically mixed ((NH₂)silica + (SH)silica) for the sake of comparison of sorption performances. It has been demonstrated that (SH)silica shows quantitative sorption only to As(III) at two pH values, 1.0 and 9.0, while (NH₂)silica displays selectivity only towards As(V) at pH 3.0. On the other hand, the bifunctional (NH₂ + SH)silica possesses the efficient features of the two mono-functionalized sorbents; for example, it retains As(III) at a wider pH range, from 1.0 to at least 9.0 with the exception at pH 2.0, and it also shows quantitative sorption to As(V) at pH 3.0. This property gives the bifunctional (NH₂ + SH)silica a better flexibility in terms of sorption performance as a function of solution pH. The mechanically mixed (NH₂)silica + (SH)silica exhibits a similar but less efficient sorption behavior compared to the bifunctional sorbent. Desorption of both As(III) and As(V) species can be realized using 0.5 M NaOH. The validity of the proposed method was checked through the analysis of a standard reference material and a good correlation was obtained between the certified (26.67 μg L⁻¹) and determined (27.53 ± 0.37 μg L⁻¹) values. Spike recovery tests realized with ultrapure water (93.0 ± 2.3%) and drinking water (86.9 ± 1.2%) also confirmed the applicability of the method.     

Selectfluor-mediated mild oxidative halogenation and thiocyanation of 1-aryl-allenes with TMSX (X = Cl,Br, I,NCS) and NH4SCN

Presence of TMSX (X = Cl, Br, I) unleashes the oxidative character of Selectfluor and provides a mild dihalogenation method for 1-arylallenes. Preference for 2,3-addition was observed with TMSCl in MeCN irrespective of the nature of the substituent on the aryl moiety, whereas 1,2-addition was preferred in [BMIM][BF₄]. With TMSBr and TMSI only products corresponding to 2,3-addition were observed. Reactions carried out with TMSBr in IL solvents gave the corresponding monobromoalkenes as a major product along with the isomeric dibromo-alkenes. Reaction with NH₄SCN provided convenient access to dithiocyanate derivatives. The same products were formed via TMS-NCS/Selectfluor. Formation of common products via TMSNCS and NH₄SCN points to the formation and interplay of SCN⁺/NCS⁺ as incipient electrophiles.     

The separation of arsenic species in soils and plant tissues by anion-exchange chromatography with inductively coupled mass spectrometry using various mobile phases

Anion-exchange chromatography (Hamilton, PRP-X100) with inductively coupled plasma mass spectrometry (ICP-MS) is commonly used for the speciation of arsenic in environmental and biological samples. However, retentions for As species are frequently different because of the use of widely different mobile phases. In addition, chloride in matrices interferes with arsenic determination. In this study, we systematically investigated various mobile phases based on ammonium salts affecting arsenic retention to eliminate chloride interference chromatographically. Hence, various mobile phases based on ammonium salts, including NH₄H₂PO₄, NH₄HPO₄, NH₄Ac, NH₄HCO₃ and NH₄NO₃, were examined for reasonable resolution and to separate chloride from arsenic species. The best result was obtained with a mobile phase containing 30 mM NH₄H₂PO₄ at pH 5.6, where the separation of arsenic species, including arsenite [As(III)], arsenate [As(V)], dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA)], was achieved within 9 minutes with reasonable resolution and free of chloride interference at its high level (500 mg L^− 1). The detection limits for the arsenic species were in the range of 0.1-0.3 μg L^− 1 with a direct injection of sample without removing matrix. Finally, the proposed method was used for the determination of arsenic species in contaminated soil and plant tissues.