A new electrochemiluminescent detection system equipped with an electrically heated carbon paste electrode for CE

An electrochemiluminescent (ECL) detection system in CE with an electrically heated carbon paste electrode (CPE) was developed. This CPE could be heated by a 100 kHz alternating current (ac) generated from a function generator, and the temperature of the electrode (Te) could be controlled. To evaluate the feasibility and reliability of this system, the electrochemically generated Ru(bpy)(3) (3+)-based ECL reaction was used for detection of triethylamine (TEA) and tri-n-propylamine (TPrA). Ru(bpy)(3) (2+) was added into the separation buffer solution with precolumn mode. Effects of several important factors were investigated to acquire the optimum conditions. Under the optimum conditions, the heated electrode has been shown to provide advantages by the measurement of ECL intensity in CE at elevated Te. Compared with the conventional electrode at the room temperature, using heated CPE could improve peak shape and gain good reproducibility with lower detection limits and wider linearity ranges. Compared with the room temperature, the linear ranges and detection limits (S/N = 3) for TEA and TPrA were improved about one magnitude when the Te was 39 degrees C. In contrast, the RSD was lower than for the electrode at room temperature.     

Determination of linuron in water and vegetable samples using stripping voltammetry with a carbon paste electrode

A carbon paste electrode was used for the electrochemical determination of linuron concentrations in water and vegetable extracts. Optimal conditions were established with respect to electrode activation (electrochemical pretreatment), time accumulation, potential accumulation, scan rate, and pH. The limit of detection achieved with a pre-concentration step was 23.0 μg L⁻¹. Recovery measurements in vegetable extract and natural water samples were in the range of 98-103%, indicating that the proposed electrochemical method can be employed to analyze linuron in these matrices. The determination results were in good agreement with HPLC results.     

固态碳糊电极电位法测定利多卡因注射液

本文报道了一种以利多卡因与单质碘形成的缔合物为电活性物的全固态碳糊利多卡因电极,电极的线性响应范围5.0×10-2～4.0×10-5mol.L-1,级差电位为30mV/pC,检测下限为3.0×10-5mol.L-1。该电极响应迅速,重现性好,用该电极测定了盐酸利多卡因注射液中利多卡因的含量,结果与药典法相符。     

高选择性H2O2电化学发光传感器的研制及分析特性研究

提出了基于鲁米诺和醋酸纤维素修饰碳糊电极构建H2O2电化学发光传感器的新方法。在最佳实验条件下,该传感器具有重现性好,抗干扰能力强和选择性好等优点,H2O2浓度在4.0×10-6～4.0×10-5mol L范围内与相对电化学发光强度呈线性关系。该方法测定H2O2的检出限为1.6×10-6mol L,相对标准偏差为1.4%,相关系数为0.9978。     

Preparation and characterization of a new carbon paste electrode based on ketotifen–hexacyanoferrate

A new type of carbon paste electrode (CPE) was made using ketotifen fumarate (C₂₃H₂₃NO₅S; an antiasthmatic/antianaphylactic drug) and hexacyanoferrate. This electrode was constructed using an acidic solution of ketotifen fumarate and potassium hexacyanoferrate. For this purpose, ketotifen fumarate was dissolved in acidic solution (pH 1) and hexacyanoferrate was added by agitation, resulting in ketotifen–hexacyanoferrate (Ket–HCF) precipitate. The obtained precipitate was separated and introduced into carbon paste. The electrochemical behavior of Ket–HCF CPE was studied by cyclic voltammetry. A modified electrode shows one pair of peaks with surface-confined characteristics, with a 0.1-M phosphate buffer as supporting electrolyte. The effects of pH, alkali metal cations, and anions of supporting electrolytes on the electrochemical characteristics of modified electrodes were studied. The diffusion coefficients of hydrated K⁺ in film (D), the transfer coefficient (α), and the transfer rate constant for electrons (k _s) were determined.     

碳糊修饰电极吸附伏安法测定食品中的锑

研制了溴邻苯三酚红 (BPR)作修饰剂的碳糊修饰电极 ,并用此电极作工作电极建立了测定痕量锑的吸附伏安法。在选定的实验条件下 ,峰电流与Sb(Ⅲ )浓度在 8.0× 1 0 -9～ 2 .0× 1 0 -7mol L范围内呈线性关系 ,检出限为 2 .0×1 0 -9mol L ,1 0次测定相对标准偏差为 2 .0 % ,不用分离 ,可直接测定食品中痕量Sb(Ⅲ ) ,测定的回收率为 90 %～ 1 0 3%。     

Determination of polybrominated diphenyl ethers in river water by combination of liquid–liquid extraction and gas chromatography–mass spectrometry

In this work,a reliable and sensitive method for detecting polybrominated diphenyl ethers(PBDEs) has been developed by the combination of liquid–liquid extraction and gas chromatography–mass spectrometry.PBDEs were extracted from a large volume of water by liquid–liquid extraction and purified by silica gel chromatography.In order to reduce the deviation,dibromobiphenyl was exploited as the internal standard to minimize differences among the injections.The quantification was performed using an external standard.Good linear correlation coefficients(0.991) and a wide linearity range(1.0–500.0 ng/L) indicated the steadiness of the proposed method.Moreover,the satisfactory recovery(75%)suggested that successful determination of PBDEs in river water had been achieved.Furthermore,the deduction behavior of PBDEs in river water could be inferred according to the results.     

碳糊电极阳极吸附伏安法测定洛美沙星

报道了碳糊电极阳极吸附伏安法测定洛美沙星的新方法。在0.096mol L的KHP NaOH(pH5.4)缓冲液中,用碳糊电极为工作电极,在0.3V(vs.SCE)富集一定时间,然后从0.3～1 3V以300mV s扫速线性扫描,记录其在1 02V的二次导数阳极溶出峰。溶出峰电流与洛美沙星浓度在8.0×10-9～8.0×10-8mol L(富集90s)和8.0×10-8～8.0×10-7mol L(富集30s)范围内呈良好的线性关系,相关系数分别为0.9844和0.9967,检出限为9.0×10-10mol L(S N=3)。探讨了洛美沙星在碳糊电极上的伏安性质和电极反应机理,并且成功地应用于人体尿液中洛美沙星的测定,结果与紫外光度法基本吻合。     

A new voltammetric sensor for the determination of sulfite in water and wastewater using modified-multiwall carbon nanotubes paste electrode

The electrochemical response of a modified-carbon nanotubes paste electrode with p-aminophenol was investigated as an electrochemical sensor for sulfite determination. The electrochemical behaviour of sulfite was studied at the surface of the modified electrode in aqueous media using cyclic voltammetry and square wave voltammetry. It has been found that under the optimum condition (pH 7.0) in cyclic voltammetry, the oxidation of sulfite occurs at a potential about 680?mV less positive than that of an unmodified-carbon nanotubes paste electrode. Under the optimized conditions, the electrocatalytic peak current showed linear relationship with sulfite concentration in the range of 2.0?×?10^?7–2.8?×?10^?4?mol?L^?1 with a detection limit of 9.0?×?10^?8?mol?L^?1 sulfite. The relative standard deviations for ten successive assays of 1.0 and 50.0?µmol?L^?1 sulfite were 2.5% and 2.1%, respectively. Finally, the modified electrode was examined as a selective, simple and precise new electrochemical sensor for the determination of sulfite in water and wastewater samples.     

Study on the adsorptive catalytic voltammetry of aloe-emodin at a carbon paste electrode

Recently, the studies and applications for the pola-rographic catalytic waves of organic compounds at dropping mercury electrode made considerable head-way. Tovopova et al.[1―4] reported the polarographic catalytic waves of the organic compounds containi…     

A study on the determination of chromium as chromate at a carbon paste electrode modified with surfactants

A procedure for the determination of chromium is described based on synergistic pre-concentration of the chromate anion at a carbon paste electrode modified in situ with quarternary ammonium salts such as 1-ethoxycarbonylpentadecyltrimethylammonium bromide (Septonex^®), cetyltrimethylammonium bromide (CTAB) or cetylpyridinium bromide (CPB). The proper electrochemical detection utilises the reduction Cr(VI) → Cr(III) performed in the differential pulse cathodic voltammetric mode. In discussion, considerable attention has been paid to the accumulation mechanism at the carbon paste electrode in the presence of surfactants. Furthermore, after optimising the corresponding experimental conditions (0.1-0.3 M HCl + 0.1 M NaCl as the supporting electrolyte, 2.5-25 μM as the total concentration of modifier, pre-concentration at +0.7 V versus Ag/AgCl and the stripping from +0.7 to −0.4 V), the analytical performance of the method has been evaluated. The signal of interest was reproducible within ±8% and proportional to the concentration in a range of 0.5-50 μM CrO₄²⁻, with a limit of detection (S/N = 3:1) of about 5×10⁻⁸ M CrO₄²⁻ (with accumulation for 300 s). Interference studies were focused mainly on the species capable of forming ion-pairs with the modifier; i.e., TlCl₄⁻, AuCl₄⁻, PdCl₄²⁻, PtCl₆²⁻, VO₄³⁻, MnO₄⁻ and I⁻. Practical applicability of the method was tested on model solutions via the recovery rates (typically 90-110%) or using selected certified reference materials (tea, bush leaves, clover) and two samples of black tea when the respective results were compared to those obtained by the reference determinations with ICP-AES.     

Determination of four kinds of carbamate pesticides by capillary zone electrophoresis with amperometric detection at a polyamide-modified carbon paste electrode

In this paper, a polyamide-modified carbon paste electrode in capillary zone electrophoresis with amperometric detection (CZE-AD) was firstly applied to the determination of four carbamate pesticides: fenobucarb, isoprocarb, metolcarb and carbaryl. The four carbamates were hydrolyzed in alkalescent aqueous solutions, resulting in the formation of 2-sec-butylphenol, 2-isopropylphenol, m-cresol and α-naphthol, which could be determined by amperometry after capillary electrophoretic separation. Under the selected optimum conditions, the four analytes could be perfectly separated within 23 min. The linear ranges of 2-sec-butylphenol, 2-isopropylphenol and m-cresol were from 1.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹ and that of α-naphthol was from 2.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹ and their detection limits were 3.0 × 10⁻⁸, 3.0 × 10⁻⁸, 3.0 × 10⁻⁸ and 6.0 × 10⁻⁸ mol L⁻¹, respectively (S/N = 3). Fenobucarb, isoprocarb, metolcarb and carbaryl can be indirectly determined by this CZE-AD method with recovery of 105, 104, 110 and 98% and R.S.D. of 4, 3, 4 and 3%, respectively. Above results demonstrated that this method was of high sensitivity, good repeatability and could be used in the rapid determination of the pesticide residues.     

Voltammetric determination of 2-nitrophenol at a bentonite-modified carbon paste electrode

A bentonite-modified carbon paste electrode has been applied to the determination of 2-nitrophenol by differential pulse voltammmetry. The electrochemical reduction of 2-nitrophenol at –0.8 V is carried out in an artificial sea water-formic acid/sodium formate medium at pH 4. The peak height was found to be dependent on the pH over the range 2–11; the presence of a secondary process was observed in the pH range 8–11. The peak potential showed a dependence on pH, with two linear regions with different slopes. A linear relationship between peak intensity and concentration was obtained in the range 0.07–10 mgl^–1, with a detection limit of 0.03 mg 1^–1 and a coefficient of variation of 1.3% at 5 mg 1^–1. The effects of organic and inorganic species on the 2-nitrophenol determination were studied with a view to testing the resolution of the voltammetric technique. The proposed method has been applied to sea water samples with good results.     

Electrochemical determination of naproxen in the presence of acetaminophen using a carbon paste electrode modified with activated carbon nanoparticles

In this study, cyclic voltammetry and differential pulse voltammetry were used to determine the electrochemical properties and concentration of naproxen in pharmaceutical formulation and human serum samples by using a carbon paste electrode modified with activated carbon nanoparticles. Optimum conditions were obtained at an electrode with 0.005 g activated carbon nanoparticles in a phosphate buffer solution of pH 6 as a supporting electrolyte. Linear calibration curves were obtained in the range of 0.1–120 μM, and the detection limit of naproxen determined was 0.0234 μM. The modified electrode shows good selectivity for naproxen in the presence of some organic and inorganic interferences and very good precision in real samples. Finally, naproxen was measured in the presence of acetaminophen.     

碳糊电极阳极吸附伏安法测定吡哌酸

吡哌酸（Pipmidic acid,简称PPA）,是吡喹酮类合成抗菌药物,目前的主要分析方法有分光光度法、交流示波滴定法、高效液相色谱法、阴极吸附溶出伏安法、单扫描示波极谱法、微分脉冲极谱法和循环伏安法。本文提出了在CPE上阳极吸附伏安法测定PPA的方法,并探讨了PPA在CPE上的伏安性质和电极反应机理。该法准确、简便、灵敏度高,应用于模拟尿样中痕量PPA的测定,得到满意的结果。     

替硝唑在碳糊电极上的电化学性质及电分析方法研究

运用循环伏安法(CV)、方波伏安法(SWV)研究替硝唑(TNZ)在碳糊电极(CPE)上的电化学行为、电化学动力学性质及可能的电极反应机理.TNZ在CPE上的伏安行为是一受扩散控制的不可逆电化学还原过程,还原峰电位(Epc)为-0.557 V.用方波伏安法(SWV)测定TNZ线性范围为1.0×10-5～1.0×10h-3mol/L,检出限3.3×10-7mol/L.RSD 1.3%～2.8%,加样回收率99.2%～100.6%.据此建立了TNZ含量的电化学测定方法.     

Ferrocene-mediated carbon paste electrode modified with d-fructose dehydrogenase for batch mode measurement of d-fructose

A mediated modified carbon paste and renewable surface electrode for fructose amperometric measurement based on d-fructose dehydrogenase (FDH) was prepared and optimized. Commercially available ferrocene (FcH) and hydroxymethyl ferrocene (FcCH₂OH) were used as mediators. The substituted FcH showed better linearity and higher sensitivity. The influence of different experimental parameters was studied for optimum analytical performance. The final FDH-modified electrode showed good analytical performance for batch mode measurements of fructose.     

嵌入式超薄化学修饰碳糊电极及抗坏血酸的电化学行为研究

以镍铬合金为基体,在其表面构建了嵌入式超薄邻啡口罗啉修饰碳糊电极,以扫描电镜表征电极形貌、电化学技术研究电极的电化学性质。该电极对抗坏血酸(AA)有灵敏的响应,在pH 2.0的B.R.缓冲溶液中,AA的氧化峰电流与其浓度在1.0×10-7~1.0×10-4mol/L范围内呈良好的线性关系,检出限为6.0×10-8mol/L。该电极可用于AA的电化学测量。     

Determination of lead and cadmium using a polycyclodextrin-modified carbon paste electrode with anodic stripping voltammetry

This work reports the use of and -cyclodextrin-modified carbon paste electrodes (CPE_-CD and CPE_-CD) to determine simultaneously Pb(II) and Cd(II) by means of the electrochemical technique known as anodic stripping voltammetry (ASV). Both modified electrodes displayed good resolution of the oxidation peaks of the said metals. Statistic analysis of the results strongly suggests that the CPE_-CD exhibited a better analytical response that the CPE_-CD, while the detection limits obtained for Pb(II) were 6.3×10^–7 M for the CPE_-CD and 7.14×10^–7 M for the CPE_-CD, whereas for Cd(II) they were 2.51×10^–6 M for the CPE_-CD and 2.03×10^–6 M for the CPE_-CD.     

乙酰二茂铁修饰碳糊电极测定废水中对氨基苯酚

利用线性扫描溶出伏安法研究了对氨基苯酚(PAP)在乙酰二茂铁修饰碳糊电极电化学行为。结果表明:在磷酸盐缓冲溶液(pH3.2)中,该修饰电极对PAP具有较好的催化活性,其峰电流与PAP浓度在7.0×10-7～3.0×10-5mol/L范围内呈线性关系,检出限为1.0×10-7mol/L(S/N=3)。利用该法测定了模拟水样中PAP的含量。