Voltammetric determination of anabolic steroid nandrolone at gold nanoparticles modified ITO electrode in biological fluids

The electrochemical behavior of nandrolone decanoate (ND) at gold nanoparticles modified indium tin oxide (ITO) electrode was investigated. Oxidation of ND has been carried out in phosphate containing supporting electrolyte in the pH range 2.1-9.2 and a well-defined oxidation peak was noticed. The peak potential (E_p) of the oxidation peak decreases linearly with increasing pH. Linear calibration curve is obtained over the nandrolone decanoate concentration range of 50 nM to 1.5 μM at pH 7.2 with a detection limit of 1.36 × 10⁻⁷ M. The proposed method is effectively applied to detect the concentration of ND in human blood serum and urine samples after 24 and 72 h of intramuscular injection. The method is rapid and does not require any pre-treatment.     

In-channel indirect amperometric detection of heavy metal ions for electrophoresis on a poly(dimethylsiloxane) microchip

In-channel indirect amperometric detection mode for microchip capillary electrophoresis with positive separation electric field is successfully applied to some heavy metal ions. The influences of separation voltage, detection potential, the concentration and pH value of running buffer on the response of the detector have been investigated. An optimized condition of 1200 V separation voltage, −0.1 V detection potential, 20 mM (pH 4.46) running buffer of 2-(N-morpholino)ethanesulfonic acid (MES) + l-histidine (l-His) was selected. The results clearly showed that Pb²⁺, Cd²⁺, and Cu²⁺ were efficiently separated within 80 s in a 3.7 cm long native separation PDMS/PDMS channel and successfully detected at a single carbon fibre electrode. The theoretical plate numbers of Pb²⁺, Cd²⁺, and Cu²⁺ were 1.2 × 10⁵, 2.5 × 10⁵, and 1.9 × 10⁵ m⁻¹, respectively. The detection limits for Pb²⁺, Cd²⁺, and Cu²⁺ were 1.3, 3.3 and 7.4 μM (S/N = 3).     

A PVC-membrane bulk optode for gallium(III) ion determination

An optical probe responsive to gallium(III) ion has been developed. The gallium sensing system was prepared by incorporating 4-(p-nitrophenyl azo)-pyrocatechol (NAP) as ionophore in a plasticized PVC membrane containing tributylphosphate (TBP) as plasticizer. The sensing membrane in contact with gallium ion at pH 3.5, changes color from yellow-brown to pink-brown. Under optimum conditions, the proposed membrane displayed a linear range of 5-83 μM with a limit of detection of 4 μM. The response time of the membrane was within 10-15 min depending on the concentration of Ga³⁺ ions. The selectivity of the probe towards gallium determination was found to be very good. Experimental results showed that the probe could be used as an effective tool in analyzing the gallium content of water samples.     

Determination of amino acids in Sargassum fusiforme by high performance capillary electrophoresis

High performance capillary electrophoresis (HPCE) was developed for quantitative determination of 18 phenylthiohydantoin (PTH)-amino acids. The influence of electrolyte concentration, pH, organic modifier and applied voltage on HPCE performance was investigated. The HPCE separation of a PTH-amino acids mixture was much improved by adding organic modifier and Tris-boric acid buffer to the run buffer. After optimization of the method, 17 PTH-amino acids in a solution containing 18 PTH-amino acids could be separated using 400 mmol l⁻¹ Tris-boric acid, 1.0 mmol l⁻¹ diethylamine at pH 9.5 adjusted with 0.1 mol l⁻¹ NaOH as a run buffer, voltage of 25 kV was applied, temperature was maintained at 25 °C, detection wavelength was 254 nm. The precision (n = 7) of this method is less than 3.2% (peak area) and 1.1% (migration time) of relative standard deviation (R.S.D.). Linearity was established over the concentration range 50-1000 μM of each derivative, with correlation coefficients (r) ranging between 0.9904 and 0.9993. The detection limits (S/N = 3) range from 2 to 48 μmol l⁻¹. The method was applied to determine amino acids in Sargassum fusiforme, a marine algae collected from Tongtou County of Zhejiang Province in China with satisfactory results.     

Determination of the carboxylic acids in acidic and basic process samples by capillary zone electrophoresis

Capillary zone electrophoresis (CZE) with indirect UV detection was used in developing a method for the simultaneous determination of inorganic anions, aliphatic and heterocyclic organic acids in various processed samples. The analytes were determined simultaneously in 10 min using an electrolyte containing 20 mM 2,3-pyrazine dicarboxylic acid, 65 mM tricine, 2 mM BaCl₂, 0.5 mM cetyltrimethylammonium bromide, and 2 M urea at pH 8.06. Linear plots for the analytes were obtained in the concentration range of 2–150 mg L⁻¹. Relative standard deviations (RSDs) of peak areas during a 3-day analysis period varied from 5.5% for glycolate to 9.5% for oxalate. RSDs of migration times varied between 0.4% and 1.1%. The detection limit (at S/N 3) was 1 mg L⁻¹ for all the analytes studied. The proposed method was successfully demonstrated for the determination of carboxylic acids in eight oxygen treated samples of commercial softwood and hardwood kraft lignin and two red wine samples of Pinot Noir grapes. In the kraft lignin samples the concentrations of carboxylic acids correspond to the oxidation time. The acid concentrations of wine varied considerable.     

Application of 2-mercaptobenzothiazole self-assembled monolayer on polycrystalline gold electrode as a nanosensor for determination of Ag(I)

Fabrication and application of a voltammetric sensor based on gold 2-mercaptobenzothiazole self-assembled monolayer (Au-MBT SAM) for determination of silver ion is described. Preliminary experiments were performed to characterize the monolayer. The surface pK_a determined for the MBT monolayer is 7.0. This value was obtained by impedimetric titration of the monolayer in the presence of Fe(CN)₆^3−/4− as a redox probe. The extent of surface coverage was evaluated as 1.52 × 10⁻⁹ mol cm⁻² based on charged consumed for reductive desorption of the monolayer in the 0.50 M NaOH solution. Then the sensor was used for determination of Ag(I) by square wave voltammetry. The parameters affecting the sensor response, such as pH and supporting electrolyte, were optimized. A dynamic calibration curve with two linear parts was obtained in the concentration ranges of 5 × 10⁻⁸-8 × 10⁻⁷ and 1 × 10⁻⁶-1 × 10⁻⁵ M of Ag(I). The detection limit adopted from cathodic striping square wave voltammetry was as 1 × 10⁻⁸ M for n = 7. Furthermore, the effect of potential interfering ions on the determination of Ag(I) was studied, and an appropriate method was used for the elimination of this effect.     

Quantification of biogenic amines by microchip electrophoresis with chemiluminescence detection

A highly sensitive microchip electrophoresis (MCE) method with chemiluminescence (CL) detection was developed for the determination of biogenic amines including agmatine (Agm), epinephrine (E), dopamine (DA), tyramine, and histamine in human urine samples. To achieve a high assay sensitivity, the targeted analytes were pre-column labeled by a CL tagging reagent, N-(4-aminobutyl)-N-ethylisoluminol (ABEI). ABEI-tagged biogenic amines after MCE separation reacted with hydrogen peroxide in the presence of horseradish peroxidase (HRP), producing CL emission. Since no CL reagent was added to the running buffer, the background of the CL detection was extremely low, resulting in a significant improvement in detection sensitivity. Detection limits (S/N = 3) were in the range from 5.9 × 10⁻⁸ to 7.7 × 10⁻⁸ M for the biogenic amines tested, which were at least 10 times lower than those of the MCE–CL methods previously reported. Separation of a urine sample on a 7 cm glass/poly(dimethylsiloxane) (PDMS) microchip channel was completed within 3 min. Analysis of human urine samples found that the levels of Agm, E and DA were in the ranges of 2.61 × 10⁻⁷ to 4.30 × 10⁻⁷ M, 0.81 × 10⁻⁷ to 1.12 × 10⁻⁷ M, and 8.76 × 10⁻⁷ to 11.21 × 10⁻⁷ M (n = 4), respectively.     

Combined cation-exchange and extraction chromatographic method of pre-concentration and concomitant separation of Cu(II) with high molecular mass liquid cation exchanger after its online detection

A selective method has been developed for the extraction chromatographic trace level separation of Cu(II) with Versatic 10 (liquid cation exchanger) coated on silanised silica gel (SSG-V10). Cu(II) has been extracted from 0.1 M acetate buffer at the range of pH 4.0–5.5. The effects of foreign ions, pH, flow-rate, stripping agents on extraction and elution have been investigated. Exchange capacity of the prepared exchanger at different temperatures with respect to Cu(II) has been determined. The extraction equilibrium constant (K_ex) and different standard thermodynamic parameters have also been calculated by temperature variation method. Positive value of ΔH (7.98 kJ mol⁻¹) and ΔS (0.1916 kJ mol⁻¹) and negative value of ΔG (−49.16 kJ mol⁻¹) indicated that the process was endothermic, entropy gaining and spontaneous. Preconcentration factor was optimized at 74.7 ± 0.2 and the desorption constants K_desorption¹(1.4 × 10⁻²) and K_desorption²(9.8 × 10⁻²) were determined. The effect of pH on R_f values in ion exchange paper chromatography has been investigated. In order to investigate the sorption isotherm, two equilibrium models, the Freundlich and Langmuir isotherms, were analyzed. Cu(II) has been separated from synthetic binary and multi-component mixtures containing various metal ions associated with it in ores and alloy samples. The method effectively permits sequential separation of Cu(II) from synthetic quaternary mixture containing its congeners Bi(III), Sn(II), Hg(II) and Cu(II), Cd(II), Pb(II) of same analytical group. The method was found effective for the selective detection, removal and recovery of Cu(II) from industrial waste and standard alloy samples following its preconcentration on the column. A plausible mechanism for the extraction of Cu(II) has been suggested.     

Competitive magnetic immunoassay for protein detection in thin channels

Functional magnetic nanoparticles are prepared and characterized for protein detection in a magnetic separation channel. This detection method is based on a competitive immunoassay of magnetic separation in thin channels using functional magnetic nanoparticles. We used protein A–IgG complex to demonstrate the feasibility. Free IgG and fixed number of IgG-labeled microparticles were used to compete for limited sites of protein A on the magnetic nanoparticles. Several experimental parameters were investigated for protein detection. The deposited percentages of IgG-labeled microparticles at various concentrations of free IgG were determined and used as a reference plot. The IgG concentration in a sample was deduced and determined based on the reference plot using the deposited percentage of IgG-labeled microparticles from the sample. The linear range of IgG detection was from 5.0 × 10⁻⁸ to 1.0 × 10⁻¹¹ M. The detection limit was 3.69 × 10⁻¹² M. The running time was less than 10 min. Selectivities were higher than 92% and the relative errors were less than 7%. The IgG concentration of serum was determined to be 3.6 mg ml⁻¹. This measurement differed by 8.3% from the ELISA measurement. The recoveries of IgG spiked in serum were found to be higher than 94%. This method can provide simple, fast, and selective analysis for protein detection and other immunoassay-related applications.     

Sensitive pseudobienzyme electrocatalytic DNA biosensor for mercury(II) ion by using the autonomously assembled hemin/G-quadruplex DNAzyme nanowires for signal amplification

Herein, a novel sensitive pseudobienzyme electrocatalytic DNA biosensor was proposed for mercury ion (Hg²⁺) detection by using autonomously assembled hemin/G-quadruplex DNAzyme nanowires for signal amplification. Thiol functionalized capture DNA was firstly immobilized on a nano-Au modified glass carbon electrode (GCE). In presence of Hg²⁺, the specific coordination between Hg²⁺ and T could result in the assembly of primer DNA on the electrode, which successfully triggered the HCR to form the hemin/G-quadruplex DNAzyme nanowires with substantial redox probe thionine (Thi). In the electrolyte of PBS containing NADH, the hemin/G-quadruplex nanowires firstly acted as an NADH oxidase to assist the concomitant formation of H₂O₂ in the presence of dissolved O₂. Then, with the redox probe Thi as electron mediator, the hemin/G-quadruplex nanowires acted as an HRP-mimicking DNAzyme that quickly bioelectrocatalyzed the reduction of produced H₂O₂, which finally led to a dramatically amplified electrochemical signal. This method has demonstrated a high sensitivity of Hg²⁺ detection with the dynamic concentration range spanning from 1.0 ng L⁻¹ to 10 mg L⁻¹ Hg²⁺ and a detection limit of 0.5 ng L⁻¹ (2.5 pM) at the 3S_blank level, and it also demonstrated excellent selectivity against other interferential metal ions.     

Surface plasmon resonance study on enhanced refractive index change of an Ag ion-sensing membrane containing dithiosquarylium dye

In this study, we have fabricated an Ag⁺ ion-sensing membrane with a dithiosquarylium (DTSQ) dye containing a polymeric film. The selective sensing signal through the electrostatic interaction between the DTSQ dye and the Ag⁺ metal cation was effectively transduced to the refractive index (RI) change corresponding to shifts of the surface plasmon resonance (SPR) angle. In addition, a good selective Ag⁺ ion detection appeared in a wide concentration range from 10⁻⁴ to 10⁻¹² M. The resonance angle shift is interpreted with Fresnel equations and Kramers-Kronig relation. In light of these calculations, the enhanced RI increase in this sensing membrane appeared to be caused by the decrease of absorption coefficient of DTSQ dye around the wavelength of SPR probe beam. These results suggest that chromogenic approaches (λ_max control of Ag⁺ ion-sensing membrane with a DTSQ dye by appropriate molecular design) related to SPR phenomena (RI change at the wavelength of probe beam) offer a good strategy for highly sensitive metal ion detection.     

A novel method for analysis of explosives residue by simultaneous detection of anions and cations via capillary zone electrophoresis

A novel electrolyte has been developed for the simultaneous separation of cations and anions in low explosive residue by capillary electrophoresis. This electrolyte contains 15 mM α-hydroxyisobutyric acid (HIBA) as the buffer, 6 mM imidazole as the cation chromophore, 3 mM 1,3,6-naphthalenetrisulfonic acid (NTS) as the anion chromophore, 4 mM 18-crown-6 ether as a cation selectivity modifier, and 5% (v/v) acetonitrile as an organic modifier. The pH was adjusted to 6.5 using tetramethylammonium hydroxide (TMAOH), an electroosmotic flow modifier. The method was optimized by varying the concentrations of α-HIBA, imidazole, and 1,3,6-NTS at three different pH values. The results provided a simultaneous indirect photometric analysis of both anions and cations with detection limits ranging from 0.5 to 5 ppm for anions and from 10 to 15 ppm for cations with a total run time of under 7 min. The method was then applied to the analysis of Pyrodex^® RS and black powder, as well as several smokeless powders. The results obtained were consistent with previously reported results for separate anion and cation analysis and provide a faster, more complete analysis of each sample in a single chromatographic run.     

Innovative approach for the electrochemical detection of non-electroactive organophosphorus pesticides using oxime as electroactive probe

An innovative approach for sensitive and simple electrochemical detection of non-electroactive organophosphorus pesticides (OPs) was described in this report. The novel strategy emphasized the fabrication of an oxime-based sensor via attaching pralidoxime (PAM) on graphene quantum dots (GQDs) modified glassy carbon electrode. The introduction of GQDs significantly increased the effective electrode area, and then enlarged the immobilization quantity of PAM. Thus, the oxidation current of PAM was obviously increased. Relying on the nucleophilic substitution reaction between oxime and OPs, fenthion was detected using PAM as the electroactive probe. Under optimum conditions, the difference of oxidation current of PAM was proportional to fenthion concentration over the range from 1.0 × 10⁻¹¹ M to 5.0 × 10⁻⁷ M with a detection limit of 6.8 × 10⁻¹² M (S/N = 3). Moreover, the favorable detection performance in water and soil samples heralded the promising applications in on-site OPs detection.     

Determination of synthetic pharmaceuticals in phytotherapeutics by capillary zone electrophoresis with contactless conductivity detection (CZE-CD)

In this work, a method for simultaneous determination of amfepramone, fenproporex, sibutramine and fluoxetine was developed by capillary zone electrophoresis with capacitively coupled contactless conductivity detection (C⁴D) using a homemade capillary electrophoretic system. The optimized conditions for the separation of the pharmaceuticals by CZE were as follows: 50 mmol L^− 1 phosphate buffer (pH 5.0) in 50/50 (v/v) mixture of water/acetonitrile as the working electrolyte, 15 kV separation voltage, 25 °C separation temperature, hydrodynamic injection by gravity using 20 cm injection height and 60 s injection time. The detection by C⁴D was carried out by using a homemade detector, which employs a sinusoidal wave generator operating at 600 kHz frequency and 2 V_pp wave amplitude. The optimized and validated CZE-C⁴D method was applied for the determination of the studied pharmaceuticals as adulterants in phytotherapeutic formulations commercialized in Brazil for slimming purposes.     

Low pressure ion chromatography with a low cost paired emitter-detector diode based detector for the determination of alkaline earth metals in water samples

The use of a low pressure ion chromatograph based upon short (25 mm × 4.6 mm) surfactant coated monolithic columns and a low cost paired emitter-detector diode (PEDD) based detector, for the determination of alkaline earth metals in aqueous matrices is presented. The system was applied to the separation of magnesium, calcium, strontium and barium in less than 7 min using a 0.15 M KCl mobile phase at pH 3, with post-column reaction detection at 570 nm using o-cresolphthalein complexone. A comparison of the performance of the PEDD detector with a standard laboratory absorbance detector is shown, with limits of detection for magnesium and calcium using the low cost PEDD detector equal to 0.16 and 0.23 mg L⁻¹, respectively. Finally, the developed system was used for the determination of calcium and magnesium in a commercial spring water sample.     

Determination of trace iron in indium phosphide wafer by on-line matrix separation and inductively coupled plasma mass spectrometry

A method for the determination of iron in indium phosphide (InP) wafer is proposed. In the present experiment, an on-line matrix separation system using an ion exchange column was combined with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of ng g⁻¹ level of iron. In the on-line matrix separation, indium and iron in the sample solution was passed through a strongly-basic anion exchange resin column with the 9 M HCl carrier solution, where indium was eluted from the column and iron was adsorbed on it. Then, iron was eluted with the carrier solution of 0.3 M HCl containing 1 ng ml⁻¹ cobalt, and it was directly introduced into the ICP-MS nebulizer. In ICP-MS measurement, cobalt in the carrier solution was used as an internal standard to correct the change in sensitivity due to matrix effect, and the peak area integration was performed to quantify iron and cobalt in the integration time range of 20-60 s from the start of the cobalt solution flow. The detection limit (3σ) for iron was 3 ng g⁻¹, and the recoveries for iron in the 0.8, 2.4, and 8.0% indium solutions were almost 100%. The method was applied to the determination of iron in commercially available iron-doped InP wafers. The obtained results for InP wafer samples with the high iron concentration were in good agreement with those obtained by graphite furnace atomic absorption spectrometry (GFAAS).     

Capillary electrophoresis for the monitoring of carboxylic acid production by Gluconobacter oxydans

Determination of carboxylic acids in Gluconobacter oxydans fermentations of wheat straw hydrolyzate was carried out. This matrix is of complex composition containing carbohydrates, organic compounds (e.g., amino acids, toxins), and inorganic salts making the analysis challenging even with separation techniques. A method based on capillary electrophoresis with indirect UV detection was developed for the simultaneous quantification of 18 carboxylic acids. The background electrolyte solution of ammonia, 2,3-pyridinedicarboxylic acid, and Ca²⁺ and Mg²⁺ salts, containing myristyltrimethylammonium hydroxide as a dynamic capillary coating reagent, was validated for the robust and repeatable separation of the carboxylic acids. Intraday relative standard deviations in the optimized method were less than 1.6% for migration times and between 1.0% and 5.9% for peak area. Interday relative standard deviations were less than 5.0% for migration times and between 5.7% and 9.3% for peak area. With 11 nl injected, detection limits for the analytes were between 10 and 43 μmol/l. Detection limits ranged from 0.1 to 0.5 pmol at signal-to-noise ratio of 3. The results demonstrated that wheat straw hydrolyzate was a suitable substrate for G. oxydans with a product yield of 45% for the formation of xylonic acid from xylose and 96% for the formation of gluconic acid from glucose.     

Modification of polypyrrole nanowires array with platinum nanoparticles and glucose oxidase for fabrication of a novel glucose biosensor

A novel glucose biosensor, based on the modification of well-aligned polypyrrole nanowires array (PPyNWA) with Pt nanoparticles (PtNPs) and subsequent surface adsorption of glucose oxidase (GOx), is described. The distinct differences in the electrochemical properties of PPyNWA–GOx, PPyNWA–PtNPs, and PPyNWA–PtNPs–GOx electrodes were revealed by cyclic voltammetry. In particular, the results obtained for PPyNWA–PtNPs–GOx biosensor showed evidence of direct electron transfer due mainly to modification with PtNPs. Optimum fabrication of the PPyNWA–PtNPs–GOx biosensor for both potentiometric and amperometric detection of glucose were achieved with 0.2 M pyrrole, applied current density of 0.1 mA cm⁻², polymerization time of 600 s, cyclic deposition of PtNPs from −200 mV to 200 mV, scan rate of 50 mV s⁻¹, and 20 cycles. A sensitivity of 40.5 mV/decade and a linear range of 10 μM to 1000 μM (R² = 0.9936) were achieved for potentiometric detection, while for amperometric detection a sensitivity of 34.7 μA cm⁻² mM⁻¹ at an applied potential of 700 mV and a linear range of 0.1–9 mM (R² = 0.9977) were achieved. In terms of achievable detection limit, potentiometric detection achieved 5.6 μM of glucose, while amperometric detection achieved 27.7 μM.     

A novel polymeric membrane electrode for the potentiometric analysis of Cu in drinking water

Based on a novel ionophore, an ion-selective electrode has been developed for the determination of Cu²⁺ in drinking water. Its selectivity behavior is characterized and its lower detection limit optimized for measurements with different electrolyte backgrounds. The lower detection limit was 2 × 10⁻⁹ M Cu²⁺ for samples with low ionic background and 1 × 10⁻⁷ M Cu²⁺ with ionic background typically found in drinking water.     

A ratiometric fluorescent probe for fluoride ion employing the excited-state intramolecular proton transfer

A ratiometric fluorescent probe 1 for fluoride ion was developed based on modulation of the excited-state intramolecular proton transfer (ESIPT) process of 2-(2′-hydroxyphenyl)benzimidazole (HPBI) through the hydroxyl group protection/deprotection reaction. The probe 1 was readily prepared by the reaction of HPBI with tert-butyldimethylsilyl chloride (TBS-Cl) and shows only fluorescence emission maximum at 360 nm. Upon treatment with fluoride in aqueous DMF solution, the TBS protective group of probe 1 was removed readily and ESIPT of the probe was switched on, which resulted in a decrease of the emission band at 360 nm and an increase of a new fluorescence peak around 454 nm. The fluorescent intensity ratio at 454 and 360 nm (I₄₅₄/I₃₆₀) increases linearly with fluoride ion concentration in the range 0.3-8.0 μmol L⁻¹ and the detection limit is 0.19 μmol L⁻¹. The proposed probe shows excellent selectivity toward fluoride ion over other common anions. The method has been successfully applied to the fluoride determination in toothpaste and tap water samples.