Modification of glassy carbon electrode with a polymer/mediator composite and its application for the electrochemical detection of iodate

A modified glassy carbon electrode was prepared by depositing a composite of polymer and mediator on a glassy carbon electrode (GCE). The mediator, flavin adenine dinucleotide (FAD) and the polymer, poly(3,4-ethylenedioxythiophene) (PEDOT) were electrochemically deposited as a composite on the GCE by applying cyclic voltammetry (CV). This modified electrode is hereafter designated as GCE/PEDOT/FAD. FAD was found to significantly enhance the growth of PEDOT. Electrochemical quartz crystal microbalance (EQCM) analysis was performed to study the mass changes in the electrode during the electrodeposition of PEDOT, with and without the addition of FAD. The optimal cycle number for preparing the modified electrode was determined to be 9, and the corresponding surface coverage of FAD (Γ_FAD) was ca. 5.11 × 10⁻¹⁰ mol cm⁻². The amperometric detection of iodate was performed in a 100 mM buffer solution (pH 1.5). The GCE/PEDOT/FAD showed a sensitivity of 0.78 μA μM⁻¹ cm⁻², a linear range of 4–140 μM, and a limit of detection of 0.16 μM for iodate. The interference effects of 250-fold Na⁺, Mg²⁺, Ca²⁺, Zn²⁺, Fe²⁺, Cl⁻, NO₃⁻, I⁻, SO₄²⁻ and SO₃²⁻, with reference to the concentration of iodate were negligible. The long-term stability of GCE/PEDOT/FAD was also investigated. The GCE/PEDOT/FAD electrode retained 82% of its initial amperometric response to iodate after 7 days. The GCE/PEDOT/FAD was also applied to determine iodate in a commercial salt.     

A soluble and multichromic conducting polythiophene derivative

A new soluble polythiophene derivative was synthesized by both chemical and electrochemical oxidative polymerization of 1-4-nitrophenyl-2,5-di(2-thienyl)-1H-pyrrole (SNSNO₂). Chemical method produces a polymer which is completely soluble in organic solvents. The structures of both the monomer and the soluble polymer were elucidated by ¹H and ¹³C-NMR and FTIR. The average molecular weight has been determined by GPC to be Mn = 6.3 × 10³ for the chemically synthesized polymer. P(SNSNO₂) was also synthesized via potentiostatic electrochemical polymerization. Characterizations of the resulting polymer were performed by cyclic voltammetry CV, FTIR and UV-Vis spectroscopy. Four-probe technique was used to measure the conductivities of the samples. Moreover, the spectroelectrochemical and electrochromic properties of the polymer film were investigated. In addition, dual type polymer electrochromic devices ECDs based on P(SNSNO₂) with poly3,4-ethylenedioxythiophene (PEDOT) were constructed. Spectroelectrochemistry, electrochromic switching and open circuit stability of the devices were studied. They were found to have good switching times, reasonable contrasts and optical memories.     

Investigation on PEDOT/β-Fe3+O(OH,Cl) nanospindles as a new steady electrode material for detecting iodic compounds

Poly(3,4-ethylenedioxythiophene (PEDOT)/β-Fe³⁺O(OH,Cl) nanospindles dispersed in ethanol were dropped on a glassy carbon electrode (GCE) and their electrocatalytic properties towards oxidation of KI and reduction of KIO₃ were investigated by cyclic voltammetry (CV). Compared to bare GCE, the anodic and cathodic response currents were greatly enhanced due to the spindle-like morphology which leaded to the increase of surface area. The effect of scanning rate was also studied and obtained diffusion control to the nature of oxidation process of KI and surface control to the nature of reduction process of KIO₃, respectively. PEDOT/β-Fe³⁺O(OH,Cl) nanospindles modified GCE had good stability and repeatability of CV responses and the used modified electrode could be cleaned easily by ultrasonic for several minutes. This new kind of conducting polymer/inorganic composite nanomaterials could act as a good steady and convenient electrode material for detecting iodic compounds or some other kinds of compounds.     

One step electrochemically deposited nanocomposite film of chitosan-carbon nanotubes-gold nanoparticles for carcinoembryonic antigen immunosensor application

A simple and controllable one-step electrodeposition method for the preparation of a chitosan-carbon nanotubes-gold nanoparticles (CS-CNTs-GNPs) nanocomposite film was used to fabricate an immunosensor for detection of carcinoembryonic antigen (CEA). The porous three-dimensional CS-CNTs-GNPs nanocomposite film, which offered a large specific surface area for immobilization of antibodies, exhibited improved conductivity, high stability and good biocompatibility. The morphology of the formed nanocomposite film was investigated by scanning electron microscopy (SEM), and the electrochemical behaviors of the immunosensor were characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). Under the optimal conditions, the proposed immunosensor could detect CEA in two linear ranges from 0.1 to 2.0 ng mL⁻¹ and from 2.0 to 200.0 ng mL⁻¹, with a detection limit of 0.04 ng mL⁻¹. The immunosensor based on CS-CNTs-GNPs nanocomposite film as the antibody immobilization matrix could exhibit good sensitivity, stability, and reproducibility for the determination of CEA.     

Two novel triphenylamine-substituted poly(p-phenylenevinylene) derivatives: synthesis, photo- and electroluminescent properties

Two novel triphenylamine-substituted poly(p-phenylenevinylene) derivatives, P1 and P2, have been successfully synthesized through the Witting-Horner reaction. The structures and properties of the monomers and the resulting polymers were characterized by using ¹H NMR, FT-IR, GPC, TGA, UV-vis absorption spectroscopy, cyclic voltammetry (CV) and electroluminescence (EL) spectroscopy. The obtained polymers exhibited good thermal stability and high photoluminescence quantum yield (0.42-0.90). The polymer light-emitting diodes (PLEDs) with the configuration of ITO/PEDOT/polymers/Ca/Al were fabricated. The single-layer device based on P1 and P2 emitted stable blue and yellow light with the turn-on voltage of 4 and 6 V, respectively. The maximum luminance of 3003 cd/m² at 10 V was obtained for device P2.     

Screen-printed poly(3,4-ethylenedioxythiophene) (PEDOT): A new electrochemical mediator for acetylcholinesterase-based biosensors

This work describes the use of a PEDOT:PSS-based conductive polymer for designing AChE-based biosensors. The transducers were obtained directly by screen-printing a PEDOT:PSS suspension on the surface of thick film carbon electrodes. The obtained working electrodes showed a high conductivity when compared with electrodes modified with conventional mediators like cobalt phthalocyanine or tetracyanoquinodimethane. The PEDOT:PSS polymer was shown to be suitable for thiocholine oxidation, allowing the measurement of AChE activity at 100 mV vs Ag/AgCl. The high conductivity of PEDOT:PSS allowed the accurate detection of the organophosphate insecticide chlorpyrifos-oxon at concentrations as low as 4 × 10⁻⁹ M, corresponding to an inhibition ratio of 5%.     

Detection of nicotine based on molecularly imprinted TiO2-modified electrodes

Amperometric detection of nicotine (NIC) was carried out on a titanium dioxide (TiO₂)/poly(3,4-ethylenedioxythiophene) (PEDOT)-modified electrode by a molecular imprinting technique. In order to improve the conductivity of the substrate, PEDOT was coated onto the sintered electrode by in situ electrochemical polymerization of the monomer. The sensing potential of the NIC-imprinted TiO₂ electrode (ITO/TiO₂[NIC]/PEDOT) in a phosphate-buffered saline (PBS) solution (pH 7.4) containing 0.1 M KCl was determined to be 0.88 V (vs. Ag/AgCl/saturated KCl). The linear detection range for NIC oxidation on the so-called ITO/TiO₂[NIC]/PEDOT electrode was 0-5 mM, with a sensitivity and limit of detection of 31.35 μA mM⁻¹ cm⁻² and 4.9 μM, respectively. When comparing with the performance of the non-imprinted one, the sensitivity ratio was about 1.24. The sensitivity enhancement was attributed to the increase in the electroactive area of the imprinted electrode. The at-rest stability of the ITO/TiO₂[NIC]/PEDOT electrode was tested over a period of 3 days. The current response remained about 85% of its initial value at the end of 2 days. The ITO/TiO₂[NIC]/PEDOT electrode showed reasonably good selectivity in distinguishing NIC from its major interferent, (−)-cotinine (COT). Moreover, scanning electrochemical microscopy (SECM) was employed to elucidate the surface morphology of the imprinted and non-imprinted electrodes using Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ as a redox probe on a platinum tip. The imprinted electrode was further characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR).     

Multilayered construction of glucose oxidase on gold electrodes based on layer-by-layer covalent attachment

A feasible approach to construct multilayered enzyme film on the gold electrode surface for use as biosensing interface is described. The film was fabricated by alternate layer-by-layer deposition of periodate-oxidized glucose oxidase (GOx) and poly(allylamine) (PAA). The covalent attachment process was followed and confirmed by electrochemical impedance spectroscopy (EIS). X-ray diffraction (XRD) experiments revealed that the film was homogeneous and formed in an ordered manner with a thickness of 2.6 ± 0.1 nm per bilayer. The gold electrodes modified with the GOx/PAA multilayers showed excellent electrocatalytical response to the oxidation of glucose when ferrocenemethanol was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). From the analysis of voltammetric signals, the coverage of active enzyme on the electrode surface was estimated, which had a linear relationship with the number of GOx/PAA bilayers. This suggests that the analytical performance such as sensitivity, detection limit, and so on, is tunable by controlling the number of attached bilayers. The six GOx/PAA bilayer electrode exhibited a sensitivity of 15.1 μA mM⁻¹ cm⁻² with a detection limit of 3.8 × 10⁻⁶ M. In addition, the sensor exhibited good reproducibility and stability.     

聚3,4-乙烯二氧噻吩/石墨烯/钛电极的制备及其电化学性能

采用直流电弧等离子体喷射化学气相沉积法把石墨烯生长在钛(Ti)基底上,并采用电化学氧化聚合法在石墨烯表面沉积聚3,4-乙烯二氧噻吩(PEDOT),由此构造PEDOT/石墨烯/Ti电极。形貌及结构表征结果表明,电聚合200圈以上的PEDOT呈线状或泡沫状且均匀分布于石墨烯表面。电化学性能测试结果表明,PEDOT/石墨烯/Ti电极具有高的比电容和库伦效率;其电聚合次数为400圈时,与PEDOT/Ti电极相比,比电容提高42倍,其最大电势窗口可达1.4 V,而在0～1.2 V电势窗口范围内,扫描速度为10 mV·s-1时,比电容可达到269.6 mF·cm-2。     

Novel flexible chemical gas sensor based on poly(3,4-ethylenedioxythiophene) nanotube membrane

Poly(3,4-ethylenedioxythiophene) nanotubes (PEDOT NTs) flexible membrane was successfully fabricated by vapor deposition polymerization (VDP) mediated electrospinning for ammonia gas detection. PVA nanofibers (NFs) were electrospun as a core part and polyvinyl alcohol (PVA)/PEDOT coaxial nanocables (NCs) were prepared by VDP method via EDOT monomer adsorption onto the electrospun PVA NFs as templates. To obtain the PEDOT NTs membrane, the PVA NFs were removed from PVA/PEDOT coaxial NCs with distilled water. PVA/PEDOT coaxial NCs and PEDOT NTs had the conductivities of 71 and 61 S cm⁻¹ and were applied as a transducer for ammonia gas detection in the range of 1-100 parts per million (ppm) of NH₃ gas. They exhibited the minimum detectable level of ca. 5 parts per million (ppm) and fast response time (less than 1 s) towards ammonia gas. In a recovery time, the PEDOT NTs membrane sensor was ca. 30 s and shorter compared to that of the membrane sensor based on the PVA/PEDOT NCs (ca. 50 s). In addition, sensor performance of PEDOT NTs membrane was also undertaken as a function of membrane thickness. Thick membrane sensor (30 μm) had the enhanced sensitivity and the sensitivity on the membrane thickness was in the order of 30 μm > 20 μm > 10 μm at 60 ppm of NH₃ gas.     

Phosphomolybdate-modified multi-walled carbon nanotubes as effective mediating systems for electrocatalytic reduction of bromate

Electrocatalytic properties (towards reduction of bromate in 0.5 mol dm⁻³ H₂SO₄) of multi-walled carbon nanotubes (CNTs) modified with phosphododecamolybdate (PMo₁₂) monolayers have been diagnosed using cyclic voltammetry and amperometry. The ability of negatively charged PMo₁₂-modified CNTs to attract electrostatically ultra-thin, positively charged conducting polymer (PEDOT or polypyrrole) structures is explored to grow in controlled manner hybrid organic-inorganic network electrocatalytic films. Due to the presence of three-dimensionally distributed CNTs, the films’ conductivity and porosity are improved. The hybrid systems utilizing polypyrrole, rather than PEDOT, have produced fairly higher bromate electroreduction catalytic currents. Comparison is also made to Nafion-stabilized dispersion of PMo₁₂-modified CNTs inks. The latter system is characterized by good stability and relatively the highest sensitivities with respect to bromate concentration.     

Synthesis and electropolymerization of 5,12-dihydrothieno[3′,4′:2,3][1,4]dioxocino[6,7-b]quinoxaline and its electrochromic properties

Synthesis of a new thiophene-based monomer; 5,12-dihydrothieno[3′,4′:2,3][1,4]dioxocino[6,7-b]quinoxaline (DDQ), was realized. The chemical structure of the monomer was characterized by ¹H NMR, FTIR and mass spectroscopy techniques. Electrochemical polymerization of DDQ and characterization of the resulting polymer [P(DDQ)] was performed. Moreover, the spectroelectrochemical and electrochromic properties of the polymer film were investigated. P(DDQ) has a low oxidation potential (0.9 V) and low band gap (1.73 eV) compared to polythiophene. In addition, dual-type polymer electrochromic device (ECD) based on P(DDQ) with poly(3,4-ethylenedioxythiophene) (PEDOT) was constructed. Spectroelectrochemistry, electrochromic switching, stability and open-circuit stability of the device were studied. It was observed that polymer have good switching time, reasonable contrast and optical memory.     

Highly conductive PEDOT/PSS microfibers fabricated by wet-spinning and dip-treatment in ethylene glycol

Highly conductive microfibers made of poly(3,4-ethylenedioxythiophene) doped with poly(4-styrenesulfonate) (PEDOT/PSS) were fabricated by wet-spinning and subsequent dip-treatment in ethylene glycol. The electrical conductivity of the PEDOT/PSS microfibers with a diameter of ca. 5 μm was significantly increased from 74 S cm⁻¹ to 467 S cm⁻¹ by the dip-treatment in 3 min. The result was explained by removal of insulating PSS from the surface of the PEDOT/PSS grains and crystallization of PEDOT, which led to the formation of large numbers of higher conductive grains that enhanced the transport of charge carriers in the microfiber. The mechanical properties of the microfibers were also improved by the dip-treatment where Young’s modulus and tensile strength increased from 3.2 GPa and 94 MPa to 4.0 GPa and 130 MPa, respectively.     

Amperometric detection of morphine based on poly(3,4-ethylenedioxythiophene) immobilized molecularly imprinted polymer particles prepared by precipitation polymerization

Molecular imprinting is a novel technique used for chiral separation, artificial antibodies, sensors, and assays. Typically, molecular imprinted polymers (MIPs) are monoliths with irregular shapes. However, microspherical shapes with more uniform size can be obtained by the method of precipitation polymerization, which offers a higher active surface area by manipulating its compositions. In this study, MIP particles for the target molecule, morphine, were synthesized using a precipitation polymerization method that is more facile than the previous one that produced a thermally polymerized bulk. The conducting polymer, poly(3,4-ethylenedioxythiophene) (PEDOT), was utilized to immobilize the MIP particles onto the indium tin oxide (ITO) glass as a MIP/PEDOT-modified electrode. The sensitivity for the MIP/PEDOT-modified electrode with MIP particles was 41.63 μA/cm² mM, which is more sensitive than that with non-MIP particles or that of a single PEDOT film with no incorporated particles in detecting morphine ranging from 0.1 to 2 mM. The detection limit was 0.3 mM (S/N = 3). In addition, we presented that the modified electrode can discriminate codeine that plays an interfering species.     

Electrochemical determination of L-phenylalanine at polyaniline modified carbon electrode based on β-cyclodextrin incorporated carbon nanotube composite material and imprinted sol-gel film

A sensitive and selective electrochemical sensor based on a polyaniline modified carbon electrode for the determination of l-phenylalanine has been proposed by utilizing β-cyclodextrin (β-CD) incorporated multi-walled carbon nanotube (MWNT) and imprinted sol-gel film. The electrochemical behavior of the sensor towards l-phenylalanine was investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and amperometric i-t curve. The surface morphologies of layer-by-layer assembly electrodes were displayed by scanning electron microscope (SEM). The response mechanism of the imprinted sensor for l-phenylalanine was based on the inclusion interaction of β-CD and molecular recognition capacity of the imprinted film for l-phenylalanine. A linear calibration plot was obtained covering the concentration range from 5.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1.0 × 10⁻⁹ mol L⁻¹. With excellent sensitivity, selectivity, stability, reproducibility and recovery, the electrochemical imprinted sensor was used to detect l-phenylalanine in blood plasma samples successfully.     

Characterization of gold-thiol-8-hydroxyquinoline self-assembled monolayers for selective recognition of aluminum ion using voltammetry and electrochemical impedance spectroscopy

Gold electrode surface is modified via covalent attachment of a synthesized thiol functionalized with 8-hydroxyquinoline, p-((8-hydroxyquinoline)azo) benzenethiol (SHQ), for the first time. The behavior of the nanostructured electrode surface (Au–SHQ) is characterized by electrochemical techniques including cyclic and differential pulse voltammetry (CV and DPV), and electrochemical impedance spectroscopy (EIS). The modified surface is stable in a wide range of potentials and pHs. A surface pK_a of 6.0 ± 0.1 is obtained for Au–SHQ electrode using surface acid/base titration curves constructed by CV and EIS measurements as a function of pH. These results helped to determine the charge state of the surface as a function of pH. The gold modified electrode surface showed good affinity for sensing the Al(III) ion at pH 5.5. The sensing process is based on (i) accumulation and complex formation between Al(III) from the solution phase and 8HQ function on the Au electrode surface (recognition step) and (ii) monitoring the impedance of the Au–SHQ–Al(III) complex against redox reaction rate of parabenzoquinone (PBQ) (signal transduction step). The PBQ is found to be a more suitable probe for this purpose, after testing several others. Thus, the sensor was tested for quantitative determination of Al(III) from the solution phase. At the optimized conditions, a linear response, from 1.0 × 10⁻¹¹ to 1.2 × 10⁻⁵ M Al(III) in semi-logarithmic scale, with a detection limit of 8.32 × 10⁻¹² M and mean relative standard deviation of 3.2% for n = 3 at 1.0 × 10⁻⁷ M Al(III) is obtained. Possible interferences from coexisting cations and anions are also studied. The results show that many ions do not interfere significantly with the sensor response for Al(III). Validity of the method and applicability of the sensor are successfully tested by determination of Al(III) in human blood serum samples.     

Electrode modified with a composite film of ZnO nanorods and Ag nanoparticles as a sensor for hydrogen peroxide

A conducting fluorine-doped tin oxide (FTO) electrode, first modified with zinc oxide nanorods (ZnONRs) and subsequently attached with photosynthesized silver nanoparticles (AgNPs), designated as AgNPs/ZnONRs/FTO electrode, was used as an amperometric sensor for the determination of hydrogen peroxide. The first layer (ZnONRs) was obtained by chemical bath deposition (CBD), and was utilized simultaneously as the catalyst for the photoreduction of Ag ions under UV irradiation and as the matrix for the immobilization of AgNPs. The aspect ratio of ZnONRs to be deposited was optimized by controlling the number of their CBDs to render enough surface area for Ag deposition, and the amount of AgNPs to be attached was controlled by adjusting the UV-irradiation time. The immobilized AgNPs showed excellent electrocatalytic response to the reduction of hydrogen peroxide. The resultant amperometric sensor showed 10-fold enhanced sensitivity for the detection of H₂O₂, compared to that without AgNPs, i.e., only with a layer of ZnONRs. Amperometric determination of H₂O₂ at −0.55 V gave a limit of detection of 0.9 μM (S/N = 3) and a sensitivity of 152.1 mA M⁻¹ cm⁻² up to 0.983 mM, with a response time (steady-state, t₉₅) of 30-40 s. The selectivity of the sensor was investigated against ascorbic acid (AA) and uric acid (UA). Energy dispersive X-ray (EDX) analysis, transmission electron microscopic (TEM) image, X-ray diffraction (XRD) patterns, cyclic voltammetry (CV), and scanning electron microscopic (SEM) images were utilized to characterize the modified electrode. Sensing properties of the modified electrode were studied both by CV and amperometric analysis.     

Novel iridium complexes as high-efficiency yellow and red phosphorescent light emitters for organic light-emitting diodes

A series of novel biscyclometallated iridium complexes based on spirobifluorene ligands and acetyl acetonate (acac) ancillary ligands have been synthesized and characterized. Their electrochemical properties were investigated by cyclic voltammetry (CV). HOMO, LUMO, and energy band gaps of all the complexes were calculated by the combination of UV-vis absorption spectra and CV results. TGA and DSC results indicated their excellent thermal stability and amorphous structure. All the iridium complexes were fabricated into organic light-emitting devices with the device configuration of ITO/PEDOT:PSS (50 nm)/PVK (50 wt %):PBD (40 wt %):Ir complex (10 wt %) (45 nm)/TPBI (40 nm)/LiF (0.5 nm)/Ca (20 nm)/Ag (150 nm). Yellow to red light emission has been achieved from the iridium complexes guest materials. Complex C1 (yellow light emission) achieved an efficiency of 36.4 cd/A (10.1%) at 198 cd/m² and complex C4 (red light emission) reached external quantum efficiency of 4.6%. The slight decrease of external quantum efficiency at high current density revealed that the triplet-triplet (T₁-T₁) annihilation was effectively suppressed by the new developed complexes.     

A surface-enhanced Raman scattering method for detection of trace glutathione on the basis of immobilized silver nanoparticles and crystal violet probe

Unsatisfactory sensitivity and stability for molecules with low polarizability is still a problem limiting the practical applications of surface-enhanced Raman scattering (SERS) technique. By preparing immobilized silver nanoparticles (Fe₃O₄/Ag) through depositing silver on the surface of magnetite particles, a highly sensitive and selective SERS method for the detection of trace glutathione (GSH) was proposed on the basis of a system of Fe₃O₄/Ag nanoparticles and crystal violet (CV), in which the target GSH competed with the CV probe for the adsorption on the Fe₃O₄/Ag nanoparticles. Raman insensitive GSH replaced the highly Raman sensitive CV adsorbed on the surface of Fe₃O₄/Ag particles. This replacement led to a strong decrease of the CV SERS signal, which was used to determine the concentration of GSH. Under optimal conditions, a linear response was established between the intensity decrease of the CV SERS signal and the GSH concentration in the range of 50–700 nmol L⁻¹ with a detection limit of 40 nmol L⁻¹. The use of a Fe₃O₄/Ag substrate provided not only a great SERS enhancement but also a good stability, which guarantees the reproducibility of the proposed method. Its use for the determination of GSH in practical blood samples and cell extract yielded satisfactory results.     

A highly soluble poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonic acid)/Au nanocomposite for horseradish peroxidase immobilization and biosensing

A highly soluble poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonic acid)/Au (PEDOT-PSS/Au) nanocomposite was prepared via one-step chemical synthesis and the matrix was characterized by UV-vis spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM) and transmission electron microscope (TEM). Due to the excellent aqueous compatibility and biocompatibility, the PEDOT/PSS-Au nanocomposite can be used as biomaterial for enzymes immobilization. In this system, redox enzyme, horseradish peroxidase (HRP) was integrated with PEDOT/PSS-Au nanocomposite and the direct electron transfer of HRP was observed. Moreover, we find that the HRP/PEDOT-PSS/Au modified electrode shows excellent electrocatalytic ability for H₂O₂ and the formal Michaelis-Menten constant was 0.78 mmol/L. The response currents have good linear relation with the concentrations of H₂O₂ with a linear range from 2.0 × 10⁻⁷ to 3.8 × 10⁻⁴ mol/L.