Determination of polycyclic aromatic hydrocarbons in soy isoflavone nutraceutical products by gas chromatography coupled to triple quadrupole tandem mass spectrometry

Thirteen polycyclic aromatic hydrocarbons have been determined in soy‐based nutraceutical products. First, an optimization of extraction procedure was performed, and a solid–liquid extraction assisted by sonication and a dilute and shoot procedure were compared, selecting the dilute and shoot approach for the extraction of target compounds, utilizing a mixture of acetone/n‐hexane (1:1 v/v) as extractant solvent. After this, a clean‐up step was needed bearing in mind the complexity of these matrices. Dispersive solid‐phase extraction, using a mixture of C₁₈ and Zr‐Sep+ (25 mg/mL each) was used. The separation was achieved by gas chromatography and detection with triple quadrupole tandem mass spectrometry. For quantification purposes, matrix‐matched calibration was used. The validation was applied at three concentration levels (20, 100 and 250 μg/kg), obtaining recoveries between 70 and 120% and precision values equal to or lower than 23%. Limits of detection and quantification were below 8 and 20 μg/kg, respectively. The method was applied in 11 samples, detecting five polycyclic aromatic hydrocarbons at concentrations ranging from 4.1 to 18.5 μg/kg.     

Rapid determination of polycyclic aromatic hydrocarbons in sewage sludges using microwave-assisted solvent extraction. Comparison with other extraction methods

The presence of toxic organic micropollutants in municipal sewage sludges is a major problem on account of risks associated with the agricultural use of the sludges and therefore maximum tolerance limits are imposed. The aim of our study was to develop a reliable and fast analytical procedure for the determination of polycyclic aromatic hydrocarbons in sewage sludges, using focused microwave-assisted extraction. Optimization of the extraction conditions was performed on real matrices. The results of a 2(3) factorial design showed that extraction time was the only influential factor. The selected conditions (30 W, 10 min, 30 ml solvent) were used for real sludges and a certified marine sediment, leading to recoveries of between 56 and 75%. Results of an interlaboratory test confirmed these values. Finally, the technique was compared to traditional techniques (Soxhlet, sonication), and the more recent pressurized liquid extraction technique. Focused microwave-assisted extraction remains an attractive alternative technique due to its rapidity, the low solvent volume required and its moderate investment cost.     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane (1:1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane ¶(1?:?1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Determination of 15 polycyclic aromatic hydrocarbons in aquatic products by solid‐phase extraction and GC–MS

We propose a method for the simultaneous determination of 15 kinds of polycyclic aromatic hydrocarbons in marine samples (muscle) employing gas chromatography with mass spectrometry after saponification with ultrasound‐assisted extraction and solid‐phase extraction. The experimental conditions were optimized by the response surface method. In addition, the effects of different lyes and extractants on polycyclic aromatic hydrocarbons extraction were discussed, and saturated sodium carbonate was first used as the primary saponification reaction and extracted with 10 mL of ethyl acetate and secondly 1 mol/L of sodium hydroxide and 10 mL of n‐hexane were used to achieve better results. The average recovery was 67–112%. Satisfactory data showed that the method has good reproducibility with a relative standard deviation of <13%. The detection limits of polycyclic aromatic hydrocarbons were 0.02–0.13 ng/g. Compared with other methods, this method has the advantages of simple pretreatment, low solvent consumption, maximum polycyclic aromatic hydrocarbons extraction, the fast separation speed, and the high extraction efficiency. It is concluded that this method meets the batch processing requirements of the sample and can also be used to determine polycyclic aromatic hydrocarbons in other high‐fat (fish, shrimp, crab, shellfish) biological samples.     

Accelerated extraction for determination of polycyclic aromatic hydrocarbons in marine biota

A rapid and simple method is proposed for determination of polycyclic aromatic hydrocarbons (PAH) in complex matrices such as marine biota. The method uses sonication, by means of an ultrasonic probe, as a new tool for assisted extraction, coupled with reversed-phase liquid chromatography (RP-LC) with fluorescence detection (FL) for determination of 16 US EPA priority PAH. Separation and detection of the 16 PAH were complete in 45 min by RP-LC with a C₁₈ column and acetonitrile–water gradient elution. Multivariate optimisation of the variables affecting extraction (ultrasound radiation amplitude, sonication time, and temperature of the water-bath in which the extraction cell was placed) was conducted. The accuracy of the method was determined by analysis of a certified reference material and comparison of the results obtained with those from another method (microwave-assisted extraction and GC–MS). The new technique avoids the main problems encountered in the determination of PAH in complex matrices such as marine biota, and no clean-up step is necessary. The method was applied to determination of PAH in estuarine biota samples from the Urdaibai estuary (Biscay, Spain).     

Novel approach to microwave-assisted extraction and micro-solid-phase extraction from soil using graphite fibers as sorbent

A single-step extraction-cleanup procedure involving microwave-assisted extraction (MAE) and micro-solid-phase extraction (micro-SPE) has been developed for the analysis of polycyclic aromatic hydrocarbons (PAHs) from soil samples. Micro-SPE is a relatively new extraction procedure that makes use of a sorbent enclosed within a sealed polypropylene membrane envelope. In the present work, for the first time, graphite fiber was used as a sorbent material for extraction. MAE-micro-SPE was used to cleanup sediment samples and to extract and preconcentrate five PAHs in sediment samples prepared as slurries with addition of water. The best extraction conditions comprised of microwave heating at 50 degrees C for a duration of 20 min, and an elution (desorption) time of 5 min using acetonitrile with sonication. Using gas chromatography (GC)-flame ionization detection (FID), the limits of detection (LODs) of the PAHs ranged between 2.2 and 3.6 ng/g. With GC-mass spectrometry (MS), LODs were between 0.0017 and 0.0057 ng/g. The linear ranges were between 0.1 and 50 or 100 microg/g for GC-FID analysis, and 1 and 500 or 1000 ng/g for GC-MS analysis. Granular activated carbon was also used for the micro-SPE device but was found to be not as efficient in the PAH extraction. The MAE-micro-SPE method was successfully used for the extraction of PAHs in river and marine sediments, demonstrating its applicability to real environmental solid matrixes.     

Troubleshooting with cell blanks in PLE extraction

The blank extracts obtained from the pressurized liquid extraction (PLE) of a 11 mL empty cell of ASE 200 were analysed by GC-FID and GC-ECD and many interfering peaks were detected, which could difficult the trace analysis of persistent organic pollutants (i.e. polycyclic aromatic hydrocarbons, aliphatic hydrocarbons and organochlorine pesticides). These interfering compounds were identified as phthalates, silicones and organic acids and their sources were established. A solution to this analytical trouble is a previous extraction step of the empty cell under the same conditions optimised for the sample extraction.     

Microwave assisted extraction of polycyclic aromatic hydrocarbons from atmospheric particulate samples

For several years, microwave assisted extraction (MAE) was applied to extract organic compounds such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls, etc., from soils, sediments and standard reference materials. Very few authors applied this methodology for the extraction of PAHs from atmospheric particulate matter. In the present study, MAE of polycyclic aromatic hydrocarbons with hexane/acetone (1:1) from real atmospheric particulate samples was investigated and the effect of microwave energy and irradiation time studied. The yields of extracted compounds obtained by microwave irradiation were compared with those obtained using traditional Soxhlet extraction. MAE was evaluated using spiked real atmospheric particulate samples and two standard reference materials. Analytical determinations of PAHs were carried out by high performance liquid chromatography (HPLC) with ultraviolet and fluorescence detection. The best recoveries were achieved with a microwave energy of 400 W and an irradiation time of 20 min.     

π-hole bonding: A new retention mechanism for the solid phase extraction of polycyclic aromatic hydrocarbons from the hexane extracts of soil samples

In this work, the perfluorobenzene-bonded silica sorbent was tested to adsorb polycyclic aromatic hydrocarbons in hexane. In the comparison experiments, the perfluorobenzene-bonded sorbent's performance was better than octadecyl silica sorbent and phenyl-bonded silica sorbents, which indicated that the π-hole···π bonds between perfluorobenzene and the polycyclic aromatic hydrocarbons were stronger than π···π interactions and hydrophobic interactions in hexane. Then the perfluorobenzene-bonded silica sorbent was applied to solid-phase extraction of 15 polycyclic aromatic hydrocarbons from the hexane extracts of soil samples directly without the solvent replacement, which simplified the soil pretreatment process. And the results showed that under the optimal conditions, the proposed method for the determination of polycyclic aromatic hydrocarbons in the environment soil presented good recoveries and stabilities for the 10 heavier polycyclic aromatic hydrocarbons with the recoveries ranging from 75.1% to 104.6% and the relative standard deviations being in the range of 1.4%–5.8%. The limits of detection of the method varied from 0.1 to 2 ng/g. This work reveals the great application potential of the π-hole bond as a new retention mechanism in the field of solid-phase extraction.     

Analysis of polycyclic aromatic hydrocarbons in contaminated soil by Curie point pyrolysis coupled to gas chromatography-mass spectrometry, an alternative to conventional methods

Curie point pyrolysis gas chromatography-mass spectrometry (Py-GC-MS) has been compared with classical extraction procedures (Soxhlet, sonication, KOH digestion, microwave-assisted) followed by GC-MS analysis for the determination of polycyclic aromatic hydrocarbons (PAHs) in contaminated soil. In each case, the efficiency of the technique was examined for 16 PAHs included in the US Environmental Protection Agency Priority Pollutant List. The results indicate that the recovery of PAHs is dependent on the extraction technique. The highest recoveries of PAHs were obtained with Curie point pyrolysis and KOH digestion. Py-GC-MS appeared to be interesting alternative method for the determination of PAHs in contaminated soil. The results were validated by certified soil (CRM 104) analysis.     

Application of mutually immiscible ionic liquids to the separation of aromatic and aliphatic hydrocarbons by liquid extraction: a preliminary approach

The recently discovered class of ionic liquids--mutually immiscible ionic liquids--are explored in this work for their first practical application: the separation of aromatic and aliphatic hydrocarbons by solvent extraction. For this preliminary approach, benzene and hexane were chosen as representatives of each group of hydrocarbons; the ionic liquids 1-ethyl-3-methylimidazolium bis( (trifluoromethyl)sulfonyl)amide and trihexyl(tetradecyl)phosphonium bis( (trifluoromethyl)sulfonyl)amide, which are both liquid at room temperature and hydrophobic, were selected as potential solvents. Liquid-liquid equilibrium experiments were carried out at 25 degrees C for the quaternary system formed by the two hydrocarbons and the two ionic liquids. Typical extraction parameters were calculated and analysed in order to evaluate the possibilities of the mutual immiscible ionic liquids in accomplishing the separation target. A comparison with the case of using just one of the ionic liquids was made.     

Optimization of multiwalled carbon nanotubes reinforced hollow‐fiber solid–liquid‐phase microextraction for the determination of polycyclic aromatic hydrocarbons in environmental water samples using experimental design

A novel design of hollow‐fiber liquid‐phase microextraction containing multiwalled carbon nanotubes as a solid sorbent, which is immobilized in the pore and lumen of hollow fiber by the sol–gel technique, was developed for the pre‐concentration and determination of polycyclic aromatic hydrocarbons in environmental water samples. The proposed method utilized both solid‐ and liquid‐phase microextraction media. Parameters that affect the extraction of polycyclic aromatic hydrocarbons were optimized in two successive steps as follows. Firstly, a methodology based on a quarter factorial design was used to choose the significant variables. Then, these significant factors were optimized utilizing central composite design. Under the optimized condition (extraction time = 25 min, amount of multiwalled carbon nanotubes = 78 mg, sample volume = 8 mL, and desorption time = 5 min), the calibration curves showed high linearity (R ² = 0.99) in the range of 0.01–500 ng/mL and the limits of detection were in the range of 0.007–1.47 ng/mL. The obtained extraction recoveries for 10 ng/mL of polycyclic aromatic hydrocarbons standard solution were in the range of 85–92%. Replicating the experiment under these conditions five times gave relative standard deviations lower than 6%. Finally, the method was successfully applied for pre‐concentration and determination of polycyclic aromatic hydrocarbons in environmental water samples.     

Development of a stir bar sorptive extraction and thermal desorption-gas chromatography-mass spectrometry method for the simultaneous determination of several persistent organic pollutants in water samples

Stir bar sorptive extraction (SBSE) and thermal desorption followed by capillary gas chromatography coupled to mass spectrometry (SBSE-TD-GC-MS) was applied to the simultaneous determination of ultra-traces of 16 polycyclic aromatic hydrocarbons (PAHs), 12 polychlorinated biphenyls (PCBs), 6 phthalate esters (PEs) and 3 nonylphenols (NPs) in water samples. The parameters that could affect the sorption-desorption efficiency were studied. A Plackett-Burman design was used for the screening of the main effects of the experimental parameters related to the desorption step (desorption time, desorption temperature, desorption flow, cryo-focusing temperature and vent pressure). Afterwards, two central composite designs were used to find the optimal process settings for the extraction and desorption steps. The best analytical compromise conditions for the simultaneous determination of analytes from spiked water samples were found to be: sample volume (20 mL), sodium chloride addition (30%), methanol addition (20%), desorption time (10 min), desorption temperature (300 degrees C), desorption flow (23 mL min(-1)), cryo-focusing temperature (-50 degrees C) and vent pressure (7 psi). Remarkable recovery, repeatability and reproducibility were attained. Furthermore, excellent linearities (r(2) = 0.959-0.999) and low detection limits (0.1-10 ng L(-1)) were also achieved for the congeners studied. The proposed methodology was applied for the simultaneous determination of PAHs, PCBs, PEs and NPs in sea and estuarine waters. The influence of humic acids on the recovery was also studied.     

Ferrofluid-based liquid-phase microextraction

A new mode of liquid-phase microextraction based on a ferrofluid has been developed. The ferrofluid was composed of silica-coated magnetic particles and 1-octanol as the extractant solvent. The 1-octanol was firmly confined within the silica-coated particles, preventing it from being lost during extraction. Sixteen polycyclic aromatic hydrocarbons (PAHs) were used as model compounds in the development and evaluation of the extraction procedure in combination with gas chromatography-mass spectrometry. Parameters affecting the extraction efficiency were investigated in detail. The optimal conditions were as follows: 20mL sample volume, 10mg of the silica-coated magnetic particles (28mg of ferrofluid), agitation at 20Hz, 20min extraction time, and 2min by sonication with 100μL acetonitrile as the final extraction solvent. Under optimal extraction conditions, enrichment factors ranging from 102- to 173-fold were obtained for the analytes. The limits of detection and the limits of quantification were in the range of 16.8 and 56.7pgmL(-1) and 0.06 and 0.19ngmL(-1), respectively. The linearities were between 0.5-100 and 1-100ngmL(-1) for different PAHs. As the ferrofluid can respond to and be attracted by a magnet, the extraction can be easily achieved by reciprocating movement of an external magnet that served to agitate the sample. No other devices were needed in this new approach of extraction. This new technique is affordable, efficient and convenient for microextraction, and offers portability for potential onsite extraction.     

Optimized Ultrasonic Extraction for the Determination of Polyaromatic Hydrocarbons by Gas Chromatography–Mass Spectrometry

The presence of polycyclic aromatic hydrocarbons (PAHs) in soil is an issue of concern due to their harmful effects on human health. The goal of this study was to optimize ultrasonic extraction to establish an efficient, easy, and low-cost method for the determination of 16 priority PAHs in soil. The time of extraction and solvent systems were optimized with the analysis by gas chromatography–mass spectrometry. The method was validated, and the optimum results were obtained using 1:1 cyclohexane:acetone and 1:1 hexane:acetone solvent systems with 30- and 60-min sonication times.     

分散液液微萃取-气相色谱/质谱法测定水中多环芳烃

用分散液液微萃取-气相色谱/质谱法测定水样中的16种多环芳烃(PAHs)。通过实验确定最佳萃取条件为:20μL四氯化碳作萃取剂,1.0 mL乙腈作分散剂,超声萃取1 min。在优化条件下,多环芳烃的富集倍数达到216～511,方法在0.05～50μg/L范围内呈良好的线性关系,相关系数(R2)在0.9873～0.9983之间,检出限为0.0020～0.14μg/L。相对标准偏差(RSD)在3.82%～12.45%(n=6)之间。该方法成功用于实际水样中痕量多环芳烃的测定。     

Optimization of solid‐phase microextraction using Taguchi design to quantify trace level polycyclic aromatic hydrocarbons in water

This article introduces a simple, rapid, and reliable solid‐phase microextraction (SPME) method coupled with GC‐MS for the quantitative determination of 16 polycyclic aromatic hydrocarbons in water. In this study, the Taguchi experimental design was used to optimize extraction conditions of polycyclic aromatic hydrocarbons using SPME method to obtain highly enriched analytes. Consequently, quantitative determination of polycyclic aromatic hydrocarbons in water was achieved by GC‐MS technique. The selected parameters affecting enrichment of polycyclic aromatic hydrocarbons were sample extraction time, stirring speed, temperature, ionic strength, and pH. The study revealed that optimal operating conditions were found to be 90‐min extraction time, 1400 rpm stirring speed, and 60°C sample temperature. The effect of ionic strength and pH were shown to be insignificant. Optimized conditions were also reevaluated by placing the 16 polycyclic aromatic hydrocarbons into several subgroups based on their molecular weight. The extraction efficiency of polycyclic aromatic hydrocarbons with low molecular weight was shown to be a function of only the extracting temperature. Satisfactory results were obtained for linearity (0.983–0.999), detection limits (2.67–18.02 ng/L), accuracy (71.2–99.3%), and precision (4.3–13.5%). The optimum conditions reported by other design approaches were evaluated and generalized optimum conditions were suggested.     

Highly porous silica-polyaniline nanocomposite as a novel solid-phase microextraction fiber coating

A highly porous fiber-coated SBA-15/polyaniline material was prepared for solid-phase microextraction (SPME). The SBA-15/polyaniline nanocomposite was synthesized via chemical polymerization. The prepared SBA-15/polyaniline particles were analyzed by scanning electron microscopy analysis. The prepared nanomaterial was immobilized onto a stainless steel wire for fabrication of the SPME fiber. The fiber was evaluated for the extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions in combination with gas chromatography-mass spectrometry (GC-MS). In optimum conditions (extraction temperature 60°C, extraction time 40 min, ionic strength 20%, stirring rate: 500 rpm, desorption temperature 260°C, desorption time 2 min), the repeatability for one fiber (n=3), expressed as relative standard deviation (RSD%), was between 5.3 and 8.6% for the test compounds. For deionized water, spiked with selected PAHs, the detection limits for the studied compounds were between 2 and 20 pg/mL.     

Continuous microwave-assisted extraction coupled on-line with liquid-liquid extraction: determination of aliphatic hydrocarbons in soil and sediments

This paper describes a new extraction method for the determination of aliphatic hydrocarbons (AHs) in soil and sediment samples, using continuous microwave-assisted extraction (MAE) combined with liquid-liquid extraction, for clean-up purposes. Analytical determinations were carried out by gas chromatography coupled with impact ionization mass spectrometry. The influence of the experimental conditions was tested using an agricultural soil spiked with standards (stored at 4 degrees C for 1 month) as reference soil. Maximum extraction efficiencies (80-90%) were achieved using 0.1-1.0g of sample, 60microl of water and 3ml of n-hexane (extractant) and 5min of extraction time; less than 70% of the most volatile hydrocarbons (C(9)-C(12)) were recovered since many evaporated during the drying step of the sample. MAE was compared with a conventional extraction method such as Soxhlet and a good agreement in the results was obtained (average recovery percentage value of 105% by comparing MAE against Soxhlet). Quality parameters such as linear range (0.5-800microg/g), limits of detection (LODs) (0.1-0.2microg/g) and precision (RSD, 4-6%) were determined using spiked soil samples. This method was successfully applied to the analysis of aliphatic hydrocarbons (C(9)-C(27) including pristane and phytane) in contaminated real samples.