界面键接的茂金属聚乙烯/聚合型改性蒙脱土纳米复合材料的超临界二氧化碳发泡

研究了界面具有化学键接的茂金属聚乙烯/聚合型改性蒙脱土(mPE/P-MMT)纳米复合材料的流变学行为。结果表明,与均聚聚乙烯及非界面键接的茂金属聚乙烯/十二铵改性蒙脱土(mPE/12-MMT)复合材料相比,mPE/P-MMT纳米复合材料具备由聚乙烯基体与P-MMT所组成的网络结构,因此具有较高的熔体强度(在190℃时的熔体强度为12.0cN)。用超临界二氧化碳作发泡剂对它们的发泡性能进行对比,mPE/P-MMT纳米复合材料具有更高的发泡倍率(可达14.7),其最佳发泡温度为142℃。     

双功能催化体系制备聚丙烯/蒙脱土复合材料

为了制备聚丙烯/蒙脱土纳米复合材料,将Brookhart型的乙烯齐聚催化剂负载于有机蒙脱土片层间,进一步与丙烯聚合茂金属催化剂进行复配得到双功能催化体系。采用这种双功能催化剂体系通过催化乙烯齐聚得到α-烯烃/蒙脱土的齐聚产物,进一步将丙烯与这种齐聚产物共聚,合成了一系列结构不同的聚丙烯/蒙脱土纳米复合材料。通过气相色谱、X射线衍射(XRD)分析得出蒙脱土负载的铁系催化剂催化乙烯齐聚产物是以C_4~C_(16)为主的α-烯烃,蒙脱土以片层形式分散于齐聚产物的甲苯溶液中。研究了蒙脱土负载的铁系催化剂与共聚催化剂复配催化乙烯齐聚以及丙烯与齐聚产物共聚合的情况。通过XRD、透射电镜、差示量热分析、凝胶渗透色谱分析表征可知,蒙脱土以纳米片层剥离的形式均匀分散于聚丙烯基体中,聚丙烯/复合材料的结晶温度比纯聚丙烯有所下降,所得聚丙烯基体分子量在8.1×10~4~17.1×10~4g/mo L。     

丙烯酸树脂／蒙脱土纳米复合材料的制备研究

采用离子交换法,用十六烷基三甲基溴化铵对钠基蒙脱土(Na-MMT)进行改性制备了有机蒙脱土(OMMT).用丙烯酸(AA)、硫酸化蓖麻油、乳化剂OP-10、过硫酸钾为原料进行水溶液聚合制得丙烯酸树脂.将丙烯酸树脂与改性蒙脱土通过聚合插层制备了丙烯酸树脂/ 蒙脱土纳米复合材料.通过傅立叶变换红外(FTIR)和X-射线衍射 (XRD)等手段对复合材料的结构进行了表征,结果表明:丙烯酸树脂插层进入有机蒙脱土内可形成插层型或剥离型的纳米复合材料.蒙脱土含量及蒙脱土与丙烯酸树脂的反应温度、反应时间均对复合材料的剥离行为产生影响,在蒙脱土含量为树脂固含量的7%、温度为70℃、反应4h的条件下可得到完全剥离的纳米复合材料.     

有机蒙脱土负载镍催化剂上乙醇重整制氢

采用浸渍法制备了有机改性蒙脱土(OMt)负载的Ni/有机蒙脱土(Ni/OMt)催化剂,用于乙醇重整制氢;通过XRD、FT-IR、H₂-TPR、SEM、XPS和氮吸附等手段对催化剂进行了表征分析。结果表明,与未改性的蒙脱土负载的Ni催化剂(Ni/MMT)相比,有机改性可显著提高其比表面积、孔容和金属Ni的分散度,降低碳沉积量,改善Ni/MMT催化剂的稳定性。Ni/OMt催化剂表现出较高的乙醇重整制氢催化性能,在773K下反应30 h,乙醇转化率保持在100%,氢气选择性为70%;而Ni/MMT催化剂在反应10 h即开始失活,碳沉积严重,同时产生副产物乙烯和乙醛。使用十六烷基三甲基溴化铵(CTAB)改性可促进Ni高分散在MMT层板上,抑制积炭对活性金属Ni包裹,提高其乙醇重整氢气选择性、降低乙烯和乙醛的选择性。     

有机蒙脱土负载镍催化剂上乙醇重整制氢（英文）

采用浸渍法制备了有机改性蒙脱土(OMt)负载的Ni/有机蒙脱土(Ni/OMt)催化剂,用于乙醇重整制氢;通过XRD、FT-IR、H2-TPR、SEM、XPS和氮吸附等手段对催化剂进行了表征分析。结果表明,与未改性的蒙脱土负载的Ni催化剂(Ni/MMT)相比,有机改性可显著提高其比表面积、孔容和金属Ni的分散度,降低碳沉积量,改善Ni/MMT催化剂的稳定性。Ni/OMt催化剂表现出较高的乙醇重整制氢催化性能,在773 K下反应30 h,乙醇转化率保持在100%,氢气选择性为70%;而Ni/M M T催化剂在反应10 h即开始失活,碳沉积严重,同时产生副产物乙烯和乙醛。使用十六烷基三甲基溴化铵(CTAB)改性可促进Ni高分散在MMT层板上,抑制积炭对活性金属Ni包裹,提高其乙醇重整氢气选择性、降低乙烯和乙醛的选择性。     

聚偏氟乙烯/蒙脱土纳米复合材料的形态结构

采用有机改性的蒙脱土与聚偏氟乙烯熔融共混, 制备了聚偏氟乙烯/蒙脱土纳米复合材料. 利用X射线衍射分析、透射电子显微镜(TEM)和Molau实验研究了复合材料的微观结构. 通过X射线衍射、傅里叶变换红外光谱(FTIR)以及差热扫描(DSC)研究了有机改性蒙脱土对聚偏氟乙烯结晶结构的影响. 结果表明, 有机改性蒙脱土在聚偏氟乙烯中以插层、剥离和碎片的形式存在. 在X射线衍射谱中发现蒙脱土的(001)峰向低角方向移动, 在TEM中可见到剥离的片层碎 片.蒙脱土的引入改变了聚偏氟乙烯的结晶结构, 导致了具有压电性能的β相形成, 引起α相内应力的产生, 同时也导致了聚偏氟乙烯基体的结晶度下降, 球晶尺寸随蒙脱土含量明显减少. 蒙脱土引起的β相在 160℃退火表明是相当稳定的. 根据这些实验结果, 对由于蒙脱土的引入引起的聚偏氟乙烯结晶结构的变化提出了可能的解释.     

聚N,N-二乙基丙烯酰胺蒙脱土纳米复合物的合成及溶胀性能

在制成钠基蒙脱土的基础上 ,对蒙脱土进行了改性 ,并把改性后的蒙脱土分散在N ,N 二乙基丙烯酰胺水溶液中进行聚合 .结果表明这种蒙脱土插层聚合的水凝胶的低温溶胀性能大大提高 ,其对水的释放曲线在特定的温度下也由S形转变为近一直线形 .由于蒙脱土的改性 ,在蒙脱土和聚合物之间的界面化学发生了改变 ,用X衍射分析表明此水凝胶是纳米复合材料 .而加入蒙脱土量达 10 %的水凝胶的溶胀比和温度响应性能也都发生很大改善 .     

sPS/PA6/蒙脱土纳米复合材料的制备与性能

讨论了间规聚苯乙烯 (sPS) 尼龙 6(PA6) 磺化间规聚苯乙烯 (SsPS H) 蒙脱土纳米复合材料的制备技术和新材料的结构与性能特征 .蒙脱土经层间改性处理后 (MTN) ,可分别将SsPS H和aPS(无规聚苯乙烯 )插入其纳米层间 ,制备出插层型纳米复合物MTN SsPS和MTN aPS .在sPS/PA6/SsPS H三组分共混体系中加入MTN SsPS或MTN aPS ,进行四组分熔融共混即可制备出sPS/PA6/SsPS H/蒙脱土纳米复合材料 .TEM测定证实了蒙脱土在基体中的层厚分布约为 5 0nm .此外 ,采用DSC、DMA、XRD及力学性能测试仪等现代分析方法对sPS/PA6/SsPS H/蒙脱土纳米复合材料的结构与性能进行了详细研究 .研究结果表明这种纳米复合材料具有优良的综合性能     

尼龙6/蒙脱土纳米复合材料的制备、结构与力学性能的研究

未经处理及经１１ 氨基酸处理的蒙脱土由于己内酰胺的引入而发生膨胀．己内酰氨可以在蒙脱土的硅酸盐片层间聚合，形成尼龙６／蒙脱土纳米复合材料．经１１ 氨基酸处理的蒙脱土和尼龙６分子间有很强的化学相互作用．与未经处理的蒙脱土相比，其所构成的纳米复合材料具有很好的力学性能．     

双单体原位接枝插层法制备聚丙烯纳米复合材料的研究Ⅰ.制备、表征及力学性能的研究

用有机插层剂处理蒙脱土原土 ,制得有机蒙脱土 (O MMT) .采用双单体 (马来酸酐和苯乙烯 )原位接枝插层法 ,制备了聚丙烯 蒙脱土纳米复合材料母料 .将母料与聚丙烯基体在双螺杆上共混挤出 ,制得聚丙烯 蒙脱土纳米复合材料 (PP Montmorillonetenanocomposites,PMNC) .这是制备聚合物纳米复合材料的一种新方法 .通过X 射线衍射测试 (XRD)表明 ,有机蒙脱土片层 0 0 1面间距从原土的 1 4 9nm扩大到 2 96nm ,复合材料中蒙脱土片层 0 0 1面间距由有机蒙脱土的 2 96nm扩大到 4 0nm .力学性能测试表明 ,复合材料的力学性能明显优于PP基体 ,在提高材料拉伸强度的同时 ,缺口冲击强度也得到很大的提高 .用扫描电镜 (SEM)对材料的冲击断面形貌进行了研究 ,并从理论上分析了断裂机理 .随着蒙脱土含量的增加 ,冲击断裂形式逐渐从脆性断裂变成韧性断裂     

FTIR Spectroscopic Study of Crystallization of Uniaxial Drawn Syndiotactic Polystyrene/Carbon Nanotube Nanocomposite Films

The crystallization of uniaxial hot drawn syndiotactic polystyrene/multi-walled carbon nanotube (sPS/MWCNT) nanocomposite films was studied by FTIR spectroscopy. The effects of MWCNT content, draw ratio and drawing temperature on the sPS crystallinity were investigated. The sPS/MWCMT nanocomposite films show reduced crystallinities with the increase of MWCNT content. In addition, with the increase of draw ratio, both the pure sPS and the sPS/MWCNT nanocomposite drawn films exhibit increased crystallinity. The effect of drawing temperature on the sPS crystallization is complex. In a temperature range of 100―135 ℃, the crystallinity decreases with drawing temperature, whereas it increases at 140 ℃ for both pure sPS and its nanocomposite films.     

Polymorphic behavior in syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods were used in an investigation of the structural changes in syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay was prepared by the intercalation of sPS polymer into layered montmorillonite. Both X‐ray diffraction data and transmission electron microscopy micrographs of sPS/clay nanocomposites indicated that most of the swellable silicate layers were exfoliated and randomly dispersed in the sPS matrix. The X‐ray diffraction data also showed the presence of polymorphism in the sPS/clay nanocomposites. This polymorphic behavior was strongly dependent on the thermal history of the sPS/clay nanocomposites from the melt and on the content of clay in the sPS/clay nanocomposites. Quenching from the melt induced crystallization into the α‐crystalline form, and the addition of montmorillonite probably increased heterophase nucleation of the α‐crystalline form. The effect of the melt crystallization of sPS and sPS/clay nanocomposites at different temperatures on the crystalline phases was also examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 736–746, 2002     

Crystallization kinetics and crystallization behavior of syndiotactic polystyrene/clay nanocomposites

We investigated the effects of montmorillonite (clay) on the crystallization kinetics of syndiotactic polystyrene (sPS) with isothermal differential scanning calorimetry analyses. The clay was dispersed into the sPS matrix via melt blending on a scale of 1–2 nm or up to about 100 nm, depending on the surfactant treatment. For a crystallization temperature of 240 °C, the isothermal crystallization data were fitted well with the Avrami crystallization equation. Crystallization data on the kinetic parameters (i.e., the crystallization rate constant, Avrami exponent, clay content, and clay/surfactant cation‐exchange ratio) were also investigated. Experimental results indicated that the crystallization rate constant of the sPS nanocomposite increased with increasing clay content. The clay played a vital role in facilitating the formation on the thermodynamically more favorable all‐β‐form crystal when the sPS was melt‐crystallized. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2097–2107, 2001     

Nonisothermal crystallization behavior of syndiotactic polystyrene/montmorillonite nanocomposites

X‐ray diffraction methods and differential scanning calorimetry were used to investigate the crystalline structure and crystallization kinetics of syndiotactic polystyrene (sPS)/clay nanocomposites. X‐ray diffraction data showed the presence of polymorphism in sPS/montmorillonite (MMT) nanocomposites, which was strongly dependent on the processing conditions (premelting temperature and cooling rate) of the sPS/MMT nanocomposites and on the content of MMT in the sPS/MMT nanocomposites. The α‐crystalline form could be transformed into β‐crystalline forms at higher premelting temperatures. The nonisothermal melt‐crystallization kinetics and melting behavior of the sPS/MMT nanocomposites were also studied at various cooling rates. The correlation of the crystallization kinetics, melting behavior, and crystalline structure of the sPS/MMT nanocomposites was examined. The results indicated that the addition of a small amount of MMT to sPS caused a change in the mechanism of nucleation and the crystal growth of the sPS crystallite. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 560–570, 2003     

茂钛催化剂苯乙烯原位间规聚合制备sPS/蒙脱土纳米复合材料

聚合物基纳米复合材料具有常规有机 /无机复合材料所没有的结构和形态 ,其性能较普通的聚合物复合材料更优异 ,因而引起人们的广泛关注 [1～ 4 ] .近年来的研究表明 ,运用插层聚合和熔融插层等方法可使某些具有层状结构的硅酸盐与聚合物产生特殊的界面作用 ,并以纳米尺寸均匀分     

磺化间规聚苯乙烯的表征

间规聚苯乙烯(sPS)是一种新型结晶性工程塑料,熔点达270℃,具有结晶速度快、耐热性好、耐化学腐蚀性优良等特点,可广泛用于汽车、电子、机械等行业,极具开发意义,但是由于sPS脆性大,抗冲击性差,故通过化学改性在sPS的苯环上引入极性基团,用于制成共混合金与复合材料,是提高材料韧性,开拓sPS用途的重要途径。     

sPS/PET/SsPS-H共混体系的研究

以自制间规聚苯乙烯(sPS)功能化合成的磺化间规聚苯乙烯（SsPS-H)作相容剂,研究其对sPS/PET共混物微相结构与性能的影响,发现SsPS-H能够有效地改善二者的相容性,当sPS/PET/SsPS-H为85／15／2（重量比）时,冲击强度达到11．4kJ/m^2,为纯sPS的3倍,此时材料的弯曲强度为39．1MPa,下降约8％;DMA结果表明,随SsPS-H用量的增加,共混物的Tg逐渐提高;DSC分析结果表明,共混体系中sPS的熔点不受SsPS-H含量的影响,而PET的熔点在加入6份SpPS-H时明显降低。sPS在达到最大结晶速率的温度均随SsPS-H用量的增加先提而后下降。SEM观察到加入SsPS-H后,PET分散相的尺寸减小,且均匀程度增加,共混物室温下冲击断裂显著地由脆性转变为韧性,当加入6份SsPS-H后,冲击断裂又出现脆性。     

Thermal properties and crystalline structure of syndiotactic polystyrene‐based miscible blends

This work examined the effect of the pre‐melting temperature (T_max) on the thermal properties and crystalline structure of four miscible syndiotactic polystyrene (sPS)‐based blends containing 80 wt % sPS. The counterparts for sPS included a high‐molecular‐weight atactic polystyrene [aPS(H)], a medium‐molecular‐weight atactic polystyrene [aPS(M)], a low‐molecular‐weight atactic polystyrene [aPS(L)], and a low‐molecular‐weight poly(styrene‐co‐α‐methyl styrene) [P(S‐co‐αMS)]. According to differential scanning calorimetry measurements, upon nonisothermal melt crystallization, the crystallization of sPS shifted to lower temperatures in the blends, and the shift followed this order of counterpart addition: P(S‐co‐αMS) > aPS(L) > aPS(M) > aPS(H). The change in T_max (from 285 to 315 °C) influenced the crystallization of sPS in the blends to different degrees, depending on the counterpart's molecular weight and cooling rate. The change in T_max also affected the complex melting behaviors of pure sPS and an sPS/aPS(H) blend, but it affected those of the other blends to a lesser extent. Microscopy investigations demonstrated that changing T_max slightly affected the blends' crystalline morphology, but it apparently altered that of pure sPS. Furthermore, the X‐ray diffraction results revealed that the α‐form sPS crystal content in the blends generally decreased with an increase in T_max, and it decreased with a decrease in the cooling rate as well. The blends showed a lower α‐form content than pure sPS; a counterpart of a lower molecular weight more effectively reduced the formation of α‐form crystals. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2798–2810, 2006     

Effect of the premelting temperature and sample thickness on the polymorphic behavior of syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods and differential scanning calorimetry thermal analysis have been used to investigate the structural changes of syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay nanocomposites have been prepared by the mixing of sPS polymer solutions with organically modified montmorillonite. X‐ray diffraction data and differential scanning calorimetry results indicate that the dominating crystal forms and their relative fractions in sPS and sPS/clay nanocomposites are different for various premelting temperatures (T_max's). Higher T_max's favor the formation of the thermodynamically more stable β‐crystalline form, and its relative fraction has been obtained from the X‐ray diffraction data in the range of 11.5–13°. The intensity of the X‐ray diffraction data in the range of 11.5–13° decreases as the thickness of sPS/clay nanocomposites decreases from 150 to 20 μm. At the same time, the intensity of the X‐ray data in the range of 6–7° becomes sharper as the thickness of sPS/clay nanocomposites decreases. The calculation ratio based on the peak intensities at 6.2 and 6.8° for sPS/clay nanocomposites of equal thickness and crystallinity in the pure β and α forms has also been determined in this study. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1730–1738, 2003