The reaction ofC-phenylcalix[4]resorcinarene-based polymer with quaternary ammonium and potassium cations

The resol polycondensation ofC-phenylcalix[4]resorcinarene with formaldehyde affords a corss-linked polymer possessing ion-exchange ability. The ion-exchange capacity of the polymer with respect to NH₄ ⁺, Me₄N⁺, Et₄N⁺, Bu₄N⁺, and K⁺ cations was determined. The equilibrium in the systemsC-phenylcalix[4]resorcinarene-based polymer—binary or ternary aqueous solutions of electrolytes was studied by potentiometric titration and quantumchemical MNDO/PM3 calculation Published inIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1475–1477, August, 2000.     

Sulfonic cation exchangers based on immobilized cis-Calix[4]resorcinolarenes

New sulfonic cation exchangers based on immobilized calix[4]resorcinolarenes were prepared. Their ion-exchange properties toward Na⁺, Cu²⁺, [Pd(NH₃)₄]²⁺, In³⁺, and Sn⁴⁺ ions were studied in a wide pH range, and their chemical stability was examined.     

Thermodynamics of ion exchange of H<Superscript>+</Superscript> by Na<Superscript>+</Superscript> or NH<Subscript>4</Subscript><Superscript>+</Superscript> on ion-exchange resins based on <Emphasis Type="Italic">C</Emphasis>-tetramethylcalix[4]resorcinarene

The corrected selectivity coefficients of the ion exchange H⁺-Na⁺ and H⁺-NH₄ ⁺ on ion-exchange resins based on C-tetramethylcalix[4]resorcinarene were calculated from the experimental data obtained from studying ion-exchange equilibria. The preference of the ion-exchange resins for cations increases in the sequence: Na⁺ < NH₄ ⁺ < < H⁺, and the ion-exchange resin based on (2-furyl)hydroxymethyltetramethylcalix[4]resorcinarene has a higher preference for ammonium cations. According to the results of microcalorimetric measurements, the exchange H⁺-Na⁺ on this ion-exchange resin is accompanied by the highest change in the differential enthalpy. It follows from the quantum-chemical calculations that the introduction of a (2-furyl)hydroxymethyl group into the structure of the polymer induces additional electrostatic interactions between an ammonium cation and an elementary unit of the ion-exchange resin.__________Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp. 2560–2563, December, 2004.     

New sulfonate-containing network polymers based on immobilized <Emphasis Type="Italic">cis</Emphasis>-metacyclophane-3,5,10,12,17,19,24,26-octols

Polymeric metacyclophaneoctol-based sulfonic acids have been synthesized, and their ion-exchange properties have been studied. New polymeric sulfonic acids have been obtained through the sulfonation of network polymers based on immobilized cis-metacyclophane-3,5,10,12,17,19,24,26-octols. The structure of the polymers has been investigated by means of IR spectroscopy, potentiometric titration, and elemental analysis. The polymers thus obtained possess a high ion-exchange capacity with respect to Na⁺, Cu²⁺, [Pd(NH₃)₄]²⁺, and In³⁺ cations in a wide pH range. Selectivity coefficients of Na⁺-H⁺, Cu²⁺-H⁺, and In³⁺-H⁺ ion exchange have been estimated.     

A mass spectral study of 1-(aryldimethylsilyl)-2-propanones and their isomeric 2-(aryldimethylsiloxy)-1-propenes

The mass spectra of a series of β-ketosilanes, p-Y? C₆H₄Me₂SiCH₂C(O)Me and their isomeric silyl enol ethers, p-Y? C₆H₄Me₂SiOC(CH₃)?CH₂, where Y = H, Me, MeO, Cl, F and CF₃, have been recorded. The fragmentation patterns for the β-ketosilanes are very similar to those of their silyl enol ether counterparts. The seven major primary fragment ions are [M? Me·]⁺, [M? C₆H₄Y·]⁺, [M? Me₂SiO]⁺˙, [M? C₃H₄]⁺˙, [M? HC?CCF₃]⁺˙, [Me₂SiOH]⁺˙ and [C₃H₆O]⁺˙ Apparently, upon electron bombardment the β-ketosilanes must undergo rearrangement to an ion structure very similar to that of the ionized silyl enol ethers followed by unimolecular ion decompositions. Substitutions on the benzene ring show a significant effect on the formation of the ions [M? Me₂SiO]⁺˙ and [Me₂SiOH]⁺˙, electron donating groups favoring the former and electron withdrawing groups favoring the latter. The mass spectral fragmentation pathways were identified by observing metastable peaks, metastable ion mass spectra and ion kinetic energy spectra.     

On Silylated Oxonium and Sulfonium Ions and Their Interaction with Weakly Coordinating Borate Anions

Attempts have been made to prepare salts with the labile tris(trimethylsilyl)chalconium ions, [(Me₃Si)₃E]⁺ (E=O, S), by reacting [Me₃Si-H-SiMe₃][B(C₆F₅)₄] and Me₃Si[CB] (CB⁻=carborate=[CHB₁₁H₅Cl₆]⁻, [CHB₁₁Cl₁₁]⁻) with Me₃Si-E-SiMe₃. In the reaction of Me₃Si-O-SiMe₃ with [Me₃Si-H-SiMe₃][B(C₆F₅)₄], a ligand exchange was observed in the [Me₃Si-H-SiMe₃]⁺ cation leading to the surprising formation of the persilylated [(Me₃Si)₂(Me₂(H)Si)O]⁺ oxonium ion in a formal [Me₂(H)Si]⁺ instead of the desired [Me₃Si]⁺ transfer reaction. In contrast, the expected homoleptic persilylated [(Me₃Si)₃S]⁺ ion was formed and isolated as [B(C₆F₅)₄]⁻ and [CB]⁻ salt, when Me₃Si-S-SiMe₃ was treated with either [Me₃Si-H-SiMe₃][B(C₆F₅)₄] or Me₃Si[CB]. However, the addition of Me₃Si[CB] to Me₃Si-O-SiMe₃ unexpectedly led to the release of Me₄Si with simultaneous formation of a cyclic dioxonium dication of the type [Me₃Si-μO-SiMe₂]₂[CB]₂ in an anion-mediated reaction. DFT studies on structure, bonding and thermodynamics of the [(Me₃Si)₃E]⁺ and [(Me₃Si)₂(Me₂(H)Si)E]⁺ ion formation are presented as well as mechanistic investigations on the template-driven transformation of the [(Me₃Si)₃E]⁺ ion into a cyclic dichalconium dication [Me₃Si-μE-SiMe₂]₂²⁺.     

Adduct of nonamethylferrocenecarbaldehyde with HBF4 and its transformations

Some reactions of the adduct of nonaniethylferrocenecarbaldehyde with HBF₄, [Me₅C₅FeC₅Me₄CH⁺(OH)]BF₄ ^–, and its transformation into the paramagnetic complex [Me₅C₅Fe^+-C₅Me₄CH=O]BF₄ ^– were studied. The structure of the complex was established from the chemical properties, the data from IR spectroscopy, mass spectrometry, and¹H,¹³C, and¹⁹F NMR spectroscopy and confirmed by independent synthesis.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp, 2979–2983, December, 1996.     

Analytical control of the preparation of single crystal materials by inductively coupled plasma atomic emission spectrometry

The present paper shows that inductively coupled plasma atomic emission spectrometry (ICP-AES) and the Q concept, in accordance with Boumans and Vrakking [Spectrochim. Acta Part B 43 (1988) 69] can be used in the determination of a large number of dopants with different characteristics (charge and ionic radius) in the single crystals of potassium titanylphosphate [KTiOPO₄], some of its structural analogues and potassium gadolinium tungstate [KGd (WO₄)₂]. The basic conclusion from the analytical data obtained in this work is that the incorporation of Me⁺, Me²⁺, Me³⁺, Me⁴⁺ and Me⁵⁺ ions in the crystal lattice depend on its ionic radii. The effect of the ionic charge of the dopant ions is negligible. The light on the regularities of dopant incorporation in the crystal lattice was thrown and hence on the possibilities of modifying the properties of the single crystal materials.     

Speciation and Multinuclear NMR Spectroscopic Studies of Di- and Trimethyltin(IV) Moieties with MESNA in Aqueous Medium

The interaction of Me₂Sn(IV)²⁺ and Me₃Sn(IV)⁺ with a prodrug, sodium 2-mercaptoethane sulfonate (HSCH₂CH₂SO₃Na, MESNA) abbreviated as (HL), has been studied potentiometrically in aqueous solution (I = 0.1 mol·L^?1 KNO₃, 298 K). The concentration distribution of various species formed in the solution was studied with changes in pH (~3–11). A strong coordination of MESNA with metal through the S atom of thiol group has been found. In the Me₂Sn(IV)–HL system, the species [Me₂Sn(L)]⁺ (53.1–75.6%) is predominant at acidic pH (3.73 ± 0.02) and the species [Me₂Sn(L)₂OH]^? (29.4–38.5%) is predominant at basic pH (10.32 ± 0.08). In contrast, for the Me₃Sn(IV)⁺ system, [Me₃SnL] (37.0–57.4%) is the major species at pH 7.65 ± 0.03 and [Me₃Sn(OH)] (49.9–67.2%) and [Me₃Sn(L)(OH)]^? (30.2–46.5%) are the major species at pH 11.05 ± 0.01. However, at physiological pH (7.01 ± 0.32), in both (1:1) and (1:2) Me₂Sn(IV)–HL systems, the species [Me₂Sn(L)(OH)] (67.2–89.9%) is predominant, whereas for Me₃Sn(IV)–HL (1:1) and (1:2) systems, [Me₃Sn(OH)] (53.5%) and [Me₃SnL] (56.8%) are the respective predominant species. In order to characterize the possible geometry of the proposed complex species, multinuclear (¹H, ¹³C and ¹¹⁹Sn) NMR studies were carried out at different pHs. No polymeric species were detected in the experimental pH range.     

Mixed supramolecular cation-carrier and anion-carrier facilitated transport for the selective alkali cations transport

In this paper, we describe the study of the membrane transport properties of mixed supramolecular macrocyclic cation-carriers [1·K]⁺, [2·Na]⁺ and phenylureidoarene anion-carriers [3–5·I]⁻ through bulk liquid membranes. Our efforts involve the evaluation of the transport performances of these systems designed to transport ionic salts NaI and KI and strongly depending on encoded molecular features of the anion-carrier subcomponents.     

AXIAL COORDINATION IN COBALT(II) COMPLEXES OF TWO SYNTHETIC MACROCYCLIC LIGANDS CONTAINING THE BIDENTATE α-DIIMINE GROUP

Abstract

In order to elucidate the nature of axial coordination in synthetic macrocyclic complexes of cobalt(II), we have synthesized two new series of such complexes, containing the macrocycles Me₄ [14] 1,3,8,10-tetraeneN₄ and Me₂ [14] 1,3-dieneN₄, by direct isolation of the Co(II) complexes from the condensation reaction mixtures. The complexes are formally five-coordinate in the solid state, but exhibit a tendency toward six-coordination in the presence of potential axial ligands, as demonstrated by electronic spectral and electron paramagnetic resonance studies. The Co(tetraeneN₄)⁺² and Co(dieneN₄)⁺² species are compared with the previously studied Co(Me₆ [14] 4, 11-dieneN₄)⁺² moiety with respect to axial coordination. It is concluded that the presence of methyl substituents on the six-membered chelate rings of the latter complex have a marked effect on its tendency to coordinate axial ligands.     

A chemical oscillating reaction in NaBrO3-pyruvic acid-H2SP4--[Ni(Me2[14]1,3-diene N4)]2+ system

In this paper we report a chemical oscillation catalyzed by [Ni(Me₂[14]l,3-diene N₄)]²⁺ (Me₂[14]1,3-diene N₄ denotes 2,3-dimethyl-1,4,8,11-tetraazacyclotetradeca-1,3-diene) in BrO₃-pyruvic acid-H₂SO₄ system. The domain of the existence of the oscillation waa obtained. The effect of initial concentration of the components on the oscillation were studied. The features of the oscillations were described in detail. We also examined the effects of Ag⁺, Hg²⁺, CCl₄, free radical inhibitors, etc. on the oscillations.     

The influence of an anionic additive on the properties of cation-exchanger based calcium-selective electrodes

Potentiometric and electrochemical impedance spectroscopic investigations of calcium-selective membranes containing poly(vinylchloride), dioctylphenylphosphonate, calcium (bis[4-(1,1,3,3-tetramethylbutyl)phenyl] phosphate) and different amounts of the lipophilic anionic additive tridodecylmethylammonium chloride were carried out. The addition of the lipophilic additive changes the properties of calcium-selective electrodes, e.g. slope and calcium selectivity. The selectivity for calcium in presence of H⁺, Na⁺, K⁺, NH₄ ⁺, Mg²⁺, Ba²⁺, Sr²⁺ and (C₂H₅)₄N⁺ was measured by three different methods, namely separate solution method, fixed interference method and matched potential method. Membranes with different concentration ratios between the calcium-exchanger and tridodecylmethylammonium chloride were investigated within half a year. The tendency of changing from cationic into anionic response for membranes containing nearly equivalent concentrations of cation- and anion-exchanger was shown. This inversion of the electrode response depends not only upon the concentration ratio of both ion-exchangers but also upon the total concentration of calcium-exchanger. Electrochemical impedance spectroscopy was used for monitoring the development of membrane resistances during a soaking period of one month. Based on these results dielectric constants for the calcium-selective membranes depending on the membrane composition were determined. Furthermore, the dependence of the membrane resistance on the membrane thickness and the concentration of tridodecylmethylammonium chloride was evaluated.     

The influence of an anionic additive on the properties of cation-exchanger based calcium-selective electrodes

Potentiometric and electrochemical impedance spectroscopic investigations of calcium-selective membranes containing poly(vinylchloride), dioctylphenylphosphonate, calcium (bis[4-(1,1,3,3-tetramethylbutyl)phenyl] phosphate) and different amounts of the lipophilic anionic additive tridodecylmethylammonium chloride were carried out. The addition of the lipophilic additive changes the properties of calcium-selective electrodes, e.g. slope and calcium selectivity. The selectivity for calcium in presence of H⁺, Na⁺, K⁺, NH₄ ⁺, Mg²⁺, Ba²⁺, Sr²⁺ and (C₂H₅)₄N⁺ was measured by three different methods, namely separate solution method, fixed interference method and matched potential method. Membranes with different concentration ratios between the calcium-exchanger and tridodecylmethylammonium chloride were investigated within half a year. The tendency of changing from cationic into anionic response for membranes containing nearly equivalent concentrations of cation- and anion-exchanger was shown. This inversion of the electrode response depends not only upon the concentration ratio of both ion-exchangers but also upon the total concentration of calcium-exchanger. Electrochemical impedance spectroscopy was used for monitoring the development of membrane resistances during a soaking period of one month. Based on these results dielectric constants for the calcium-selective membranes depending on the membrane composition were determined. Furthermore, the dependence of the membrane resistance on the membrane thickness and the concentration of tridodecylmethylammonium chloride was evaluated. Received: 21 July 1998 / Revised: 16 October 1998 / Accepted: 23 October 1998     

[3,3] Valenceisomeric azo bridged carbocycles and cyclic hydrazones: intramolecular [3+2] cycloaddition and [4+2] cycloreversions through n-methylation1

Unsaturated azo bridged carbocycles 1, 2, 5, 8, 12, 14 and 16 can easily be methylated with Me₃OBF₄ or MeI. Depending on structural and steric requirement and the anion, the quaternary salts obtained are stable (1-Me⁺, 2-Me⁺, 5a-Me⁺, 14a/b-Me⁺, 16a/b-Me⁺ with BF_4-), undergo [4+2] cycloreversion (8a-Ne⁺, 12-Me⁺) or intramolecular [3+2] cycloaddition after intermediate deprotonation, whereby the unusual hydrazine derivatives, the cage compounds 3-H⁺ , 4-H⁺, 6-H⁺ and 11-H⁺ are formed. Systems which contain the N=N and C=C function in 1,5-positions are isomeric with their [3,3] rearrangement products, the hydrazones endo-7, endo-10, endo-15 and endo-17. Methylation of the latter provokes the same consecutive reactions as for their azo isomers. These have been demonstrated to be the crucial intermediates for the formation of cage Compound (e.g. endo-7b-Me⁺ → 5b-Me⁺ → 6-H⁺ ). Intermolecular methyl migration of quaternized azo compounds has been established, explaining the high yields of cage compounds which can be produced by the “b-series” only.     

Effect of the ion-exchange-membrane/solution interfacial characteristics on the mass transfer at severe current regimes

In the electrodialysis of dilute solutions, performed at intense current regimes, the membrane electrical conductance and diffusion permeability are no more crucial. Of more importance become the membrane properties that control increase in the overlimiting mass transfer of salt ions, as well as H⁺ and OH^? ions in membrane systems. In this work different methods of the improving of mass-exchange characteristics of commercial ion-exchange membranes intended for operation at intense current regimes are discussed. They are based on modern concepts of mechanisms of the electroconvection (which proceeds as electroosmosis of 2nd kind), as well as mechanisms of H⁺ and OH^? ions generation at the membrane/solution interface. Influence on the membrane electrochemical and mass-exchange characteristics is possible via (a) control of chemical nature of fixed groups at membrane surfaces, in order to weaken their catalytic activity with respect to water dissociation reaction, (b) increase in the surface hydrophobicity, and (c) design of electrical inhomogeneity of the membrane/solution interface; the purpose is the facilitating of intense development of electrical convection.     

Peculiarities of interaction of H+, Me3C+, and Me3Si+ ions with multifunctional molecules in the gas phase

Peculiarities of interaction of H⁺, Me₃C⁺, and Me₃Si⁺ ions with functional groups of molecules in the gas phase have been studied. Proton tends to form chelates with virtually all of the functional groups studied, whereas Me₃Si⁺ ions exhibit no capacity for chelation. Using isomeric xylenes as examples it was shown that Me₃Si⁺ ions (unlike Me₃C⁺ ions) experience virtually no steric hindrance when they react with nucleophilic centers. Effects of functional groups present in molecules of nitriles on the generation of [M+Me₃C]⁺ adducts in the gas phase and the Ritter reaction in solution were estimated.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 1767–1773, September, 1995.This work was carried out with financial support from the International Science Foundation (Grant MA7 000) and the Russian Foundation for Basic Research (Project No. 93-03-18033).     

Adsorption phenomena on a mercury electrode in aqueous cryptand[2.2.2] solutions by the background of tetraalkylammonium salts

The electrochemical behavior of cryptand[2.2.2] (Cry) is studied on a mercury electrode in aqueous solutions of tetraalkylammonium tetrafluoroborates (Me₄N⁺, Et₄N⁺, and Bu₄N⁺). Cryptand [2.2.2] is shown to exhibit high surface activity in Me₄ NBF₄ nd Et₄NBF₄ solutions. Based on the model of two parallel capacitors supplemented by the Frumkin adsorption isotherm, the adsorption parameters of Cry by the background of Me₄BNF₄ were calculated using the regression analysis methods. The calculated dependences of the differential capacitance on the potential adequately agree with experimental curves. The adsorption characteristics of Cry in the studied solutions are compared with those in MgSO₄ solutions. By the background of Bu₄NBF₄, Cry molecules and Bu₄N⁺ cations exhibit very close surface activity and form a mixed adsorption layer.     

Easy Access to the Copper(III) Anion [Cu(CF3)4]−

CuCl or pre‐generated CuCF₃ reacts with CF₃SiMe₃/KF in DMF in air to give [Cu(CF₃)₄]^? quantitatively. [PPN]⁺, [Me₄N]⁺, [Bu₄N]⁺, [PhCH₂NEt₃]⁺, and [Ph₄P]⁺ salts of [Cu(CF₃)₄]^? were prepared and isolated spectroscopically and analytically pure in 82–99 % yield. X‐ray structures of the [PPN]⁺, [Me₄N]⁺, [Bu₄N]⁺, and [Ph₄P]⁺ salts were determined. A new synthetic strategy with [Cu(CF₃)₄]^? was demonstrated, involving the removal of one CF₃^? from the Cu atom in the presence of an incoming ligand. A novel Cu^III complex [(bpy)Cu(CF₃)₃] was thus prepared and fully characterized, including by single‐crystal X‐ray diffraction. The bpy complex is highly fluxional in solution, the barrier to degenerate isomerization being only 2.3 kcal mol^?1. An NPA study reveals a huge difference in the charge on the Cu atom in [Cu(CR₃)₄]^? for R=F (+0.19) and R=H (+0.46), suggesting a higher electron density on Cu in the fluorinated complex.     

Novel Ca-selective merocyanine-type chromoionophore derived from calix[4]arene-diamide

The synthesis and calcium-selective chromogenic ion binding properties of benzothiazolium derivative of calix[4]arene are described. The merocyanine-type ionophore derived from calix[4]arene-diamide showed selective chromogenic properties toward Ca²⁺ ions in aqueous methanol. The compound showed significant Ca²⁺ ion dependent changes in UV-vis spectral properties in the presence of other physiologically important metal ions (Na⁺, K⁺, and Mg²⁺). The pH sensitive chromogenic behavior also suggests that the compound can be used as a sensitive pH indicator around pH 6.5.