2,6-二巯基吡啶互变异构平衡体系溶剂效应的理论研究

在气相及甲苯、氯仿、乙腈和水等溶剂中对2,6-二巯基吡啶及其硫酮式互变异构体进行了HF/6-31G^**水平上的优化,其中溶液中的计算采用Onsager自洽反应场(SCRF)模型.探讨了溶剂对体系几何结构和能量的影响.结果表明:溶剂的存在与极性的增加有利于平衡体系中硫酮式异构体的存在.     

Chain transfer constants for vinyl monomers polymerized in methyl oleate and methyl stearate

Chain transfer constants were obtained for styrene, methyl methacrylate, methyl acrylate and vinyl acetate, polymerized in methyl oleate and methyl stearate at 60°C. Transfer constants increased in the order: methyl methacrylate < styrene < methyl acrylate ? vinyl acetate in both solvents. Average values of the transfer parameters were: for methyl oleate, Q_tr = 2.04 × 10^?4, e_tr = 1.08; for methyl stearate, Q_tr = 0.373 × 10^?4, e_tr = 1.01. Indication that polar species predominate in the transition state is supported by the observed order of reactivity. The usual rate dependence appeared to be followed by all of the monomers except vinyl acetate, which was retarded, severely in methyl oleate. Transfer in methyl oleate was about 5.8 times greater than that found in methyl stearate for these four monomers. The internal allylic double bond of methyl oleate had about the same reactivity in transfer as had the terminal unsaturation in N-allylstearamide at 90°C. Rough estimates were obtained of the monomer transfer constants for the long side-chain homologs of these four monomers from the respective monomer transfer constants and the experimental transfer constants, corrected for transfer to the labile groups of the solvent. It was concluded that the rate of polymerization would determine in large measure the degree of polymerization for the reactive 18-carbon homologs but that the molecular weight of poly(vinyl stearate) and (oleate) will be regulated primarily by transfer to monomer.     

Emulsion copolymerization of styrene and methyl methacrylate

Chain transfer constants to monomer have been measured by an emulsion copolymerization technique at 44°C. The monomer transfer constant (ratio of transfer to propagation rate constants) is 1.9 × 10^?5 for styrene polymerization and 0.4 × 10^?5 for the methyl methacrylate reaction. Cross-transfer reactions are important in this system; the sum of the cross-transfer constants is 5.8 × 10^?5. Reactivity ratios measured in emulsion were r₁ (styrene) = 0.44, r₂ = 0.46. Those in bulk polymerizations were r₁ = 0.45, r₂ = 0.48. These sets of values are not significantly different. Monomer feed compcsition in the polymerizing particles is the same as in the monomer droplets in emulsion copolymerization, despite the higher water solubility of methyl methacrylate. The equilibrium monomer concentration in the particles in interval-2 emulsion polymerization was constant and independent of monomer feed composition for feeds containing 0.25–1.0 mole fraction styrene. Radical concentration is estimated to go through a minimum with increasing methyl methacrylate content in the feed. Rates of copolymerization can be calculated a priori when the concentrations of monomers in the polymer particles are known.     

Polymerization of coordinated monomers. XIX. Kinetic study of the alternating copolymerization of methyl methacrylate with styrene by boron trichloride

Alternating copolymerizations of methyl methacrylate with styrene in the presence of boron trichloride at 0°C in 1,2-dichloroethane were carried out by using benzoyl peroxide as an initiator. Conversion increased proportionally with polymerization time, whereas the degree of polymerization was constant irrespective of time. The rate depended linearly on the square root of the concentration of benzoyl peroxide. The equilibrium constants for the formation of the ternary molecular complex composed of methyl methacrylate, styrene, and boron trichloride in 1,2-dichloroethane at ?20, ?10, and +4°C were determined by ¹H-NMR spectroscopy. The concentrations of the ternary molecular complex in the polymerization mixtures were evaluated from the equilibrium constant of the formation. The rate of the alternating copolymerization was proportional to the first order of the concentration of the ternary molecular complex. The distribution of methyl methacrylate-centered triads in the alternating copolymer was different from that of styrene-centered triads. These results can be explained by a mechanism involving the homopolymerization of a ternary molecular complex.     

Introduction of 2-methoxycarbonylallyl end group by copolymerization of methyl α-(phenoxymethyl)acrylate accompanying with addition-fragmentation reaction

Copolymerizations of methyl α-(phenoxymethyl)acrylate (MPMA) with methyl acrylate, methyl methacrylate, styrene, and methyl α-ethylacrylate were carried out. Addition of a polymer radical to MPMA followed by the subsequent fragmentation of poly(MPMA) radical resulted in the 2-methoxycarbonylallyl end group and phenoxy radical in the course of the copolymerization. The extent of the fragmentation determined by ¹H-NMR spectroscopy depends on reactivity of the MPMA radical toward the reference monomers. An increase in the addition rate of the MPMA radical to the reference monomer brought about suppression of the fragmentation. The addition of the MPMA radical to styrene seems to be sufficiently fast to prevent the fragmentation. Since the rate of the fragmentation relative to the propagation was considerably accelerated by raising the temperature to 110°C, MPMA can be used as a novel chain transfer agent to control molecular weight and end group at a temperature above 100°C. © 1993 John Wiley & Sons, Inc.     

Synthesis,characterization, microstructure determination,thermal studies of poly (N-vinyl pyrrolidone-maleic anhydride-methyl methacrylate)

Synthesis of Poly (N-vinyl pyrrolidone-maleic anhydride-methyl methacrylate) terpolymer using azobisisobutyronitrile in 1,4-dioxan is described. The polymers with different composition were synthesized and characterized using FTIR, ¹HNMR, ¹³NMR, TGA and DSC techniques. The monomer-monomer interactions were studied using Finemann-Ross and Kelen-Tudos methods by calculating the reactivity ratio. The reactivity ratio r₁ and r₂ with respect to methyl methacrylate and N-vinylpyrrolidone-maleic anhydride complexomer are found to be 6.05 and 0.06 respectively. The study showed methyl methacrylate have higher reactivity than N-vinyl-2-pyrrolidone-maleic anhydride complex, i.e., the terpolymer contained methyl methacrylate in higher ratio. The thermal stability of poly (N-vinyl pyrrolidone-maleic anhydride-methyl methacrylate) was 165°C and the glass transition temperature was found to increase from 153°C to 182°C as MMA concentration increase. The studies indicate the activity of the polymer to inhibit bacterial growth is very poor.     

Aqueous polymerization on clay surfaces. III. The polymerization of methyl methacrylate by montmorillonite/thiourea initiating system

Initiation of polymerization of methyl methacrylate with redox system montmorillonite (with lattice Fe³⁺)–thiourea has been achieved. The rates are dependent on both clay mineral and thiourea. Amidosulfenyl radicals are believed to initiate the polymerization on the clay surface. The polymerization produced nonextractable clay–polymer adduct up to an extent of 70 wt %. The pH of the medium (in the acidic range) did not affect the polymerization rate.     

Branched and Self-Crosslinkable Poly(methyl methacrylate)s Prepared via One-Pot Synthesis in Aqueous Emulsion

An approach to the synthesis of highly branched vinyl copolymers containing thiol and C=C crosslinking groups is proposed. This method was exemplified by the emulsion copolymerization of methyl methacrylate (MMA) and 1,6-hexanediol diacrylate (HDDA) with 2-mercaptoethyl sulfide (MES) as chain transfer agent at 70°C with 4,4′-azobis(4-cyanovaleric acid) (ACVA) as the initiator. The resulting highly branched copolymers contain both thiol and acryloyl groups. The apparent M_w (by SEC) of the resulting copolymers increased with increasing ACVA concentration, whereas the pendent acryloyl and -SH groups decreased from 6.4% to 0.8% (relative to MMA units) and 45 ×10^?5 to 5 × 10^?5 mol/g, respectively. The copolymers of MMA could be self-crosslinked thermally or by exposure to UV irradiation. The gel fraction of the thermally treated samples decreased from 46% to 7.2%, with the increasing of ACVA in the polymer synthesis, while the gel fraction of UV irradiated samples changed only slightly around 70%.     

Initiation of polymerization of methyl methacrylate by oxalic acid and iron(III) mixtures

The polymerization of methyl methacrylate either by free radical or charge transfer mechanism has been studied in dimethyl sulphoxide at 60° in the presence of oxalic acid and hexakis dimethylsulphoxide iron(III) perchlorate, [Fe(DMSO)₆](ClO₄)₃. Increased rate was noticed for 1:1 mole ratio of oxalic acid to Fe³⁺ for charge transfer polymerization; a well defined induction period was found for free radical polymerization in the same systems. Mechanisms for the two types of reaction are proposed. The rate constant for the interaction of poly(methyl methacrylate) radical with the iron-oxalate complex was found to be 1.52 × 10⁵ l. mol^?1 sec^?1 at 60°.     

Studies on the polymerization of ethyl acrylate. II. Chain transfer studies

Transfer constants for different solvents representing hydrocarbons, halogenated compounds, alcohols, ketones, acids, and esters were determined in the thermal polymerization of ethyl acrylate at 80°C and they are compared with the available data on methyl acrylate and ethyl methacrylate. It was observed from the values of transfer constants that ethyl acrylate radicals are a little more effective than methyl acrylate or ethyl methacrylate in abstracting hydrogen atom from hydrocarbons and alcohols. In acetic and n-butyric acid media, it has been found, by the aid of endgroup analysis, that the derived solvent radicals from transfer reactions are not too efficient to start a new chain.     

Radical Polymerizations of Vinyl Monomers in the Presence of α-Ethylsulfenyl Acrylonitrile

Radical polymerizations of styrene, methyl methacrylate, and acrylonitrile were carried out at 60°C in the presence of α-ethylsulfenyl acrylonitrile (α-ESAN). The rate of polymerization was found to be reduced by the addition of α-ESAN, and induction periods were observed when a large amount of α-ESAN was added to the systems. The chain transfer constant of α-ESAN was determined to be 2.0 and 17 for the polymerizations of styrene and methyl methacrylate, respectively. The Q, and e, values of α-ESAN were evaluated as 4.9 and -1.9, respectively. The presence of chromium(II) acetate and a-ESAN results in enhancement of α-ESAN activity as a retarder. From these results and ESR measurements, a mechanism of chain transfer is discussed.     

Chain transfer for vinyl monomers polymerized in N-allylstearamide

Apparent transfer constants have been determined for styrene, methyl methacrylate vinyl acetate, and diethyl maleate polymerized in N-allylstearamide at 90°C. Regression coefficients for transfer were: methyl methacrylate, 0.301 × 10^?3; styrene, with no added initiator, 0.582 × 10^?3; styrene, initiated with benzoyl peroxide, 0.830 × 10^?3; vinyl acetate, 62.01 × 10^?3; and diethyl maleate, 2.24 × 10^?3. Rates of polymerization were retarded for both styrene and methyl methacrylate. Vinyl monomer and comonomer disappearance followed an increasing exponential dependence on both initiator and monomer concentration. Although degradative chain transfer probably caused most of the retardation, the cross-termination effect was not eliminated as a contribution factor. Rates for the vinyl acetate copolymerization were somewhat retarded, even though initiator consumption was large because of induced decomposition. The kinetic and transfer data indicated that the reactive monomers added radicals readily, but that rates were lowered by degradative chain transfer. Growing chains were terminated at only moderate rates of transfer. Unreactive monomers added radicals less easily, producing reactive radicals, which transferred rapidly, so that molecular weights were lowered precipitously. Although induced initiator decomposition occurred, rates were still retarded by degradative chain transfer. A simple empirical relation was found between the reciprocal number-average degree of polymerization, 1/X?_n1 and the mole fraction of allylic comonomer entering the copolymer F₂, which permitted estimation of the molecular weight of copolymers of vinyl monomers with allylic comonomers. This equation should be applicable when monomer transfer constants for each homopolymer are known and when osmometric molecular weights of one or two copolymers of low allylic content have been determined.     

Polymerization of coordinated monomers. VI. Molecular complex formation of methyl methacrylate coordinated to stannic chloride with styrene or toluene

The equilibrium constants for the complex formation between stannic chloride and methyl methacrylate were determined in n-hexane–toluene solution at 0, ?20, and ?30°C by using the absorption band at 350 nm. Continuous variation plots at ?20°C in n-hexane based on the ¹H-chemical shifts definitely show a 1:1 interaction between the coordinated methyl methacrylate and styrene or toluene. The magnitudes of the shifts for the four groups of protons in methyl methacrylate are found to be in a specific ratio in common with the 1:2 complex–styrene or -toluene system. The equilibrium constants for the ternary molecular complex formation between the 1:2 complex and styrene or toluene were determined in n-hexane in the temperature range ?50 to +20°C by use of the chemical shifts. The concentrations of the complex species in the alternating copolymerization solutions were estimated by use of the equilibrium constants. There is a linear relationship between the enthalpy and the entropy changes for the ternary molecular complex formation, which is governed by the enthalpy factor. The specificity of the interactions indicates a specific time-averaged orientation of benzene ring to the coordinated methyl methacrylate. The effects of the coordination of methyl methacrylate to stannic chloride were discussed on the basis of results of ¹³C-NMR spectroscopy.     

Grafting vinyl monomers onto silk fibers. IX. Graft copolymerization of methyl methacrylate onto silk using peroxydiphosphate-thiourea redox system

The graft copolymerization of methyl methacrylate (MMA) onto silk in aqueous media initiated by the potassium peroxydiphosphate-thiourea redox system was studied at 50°C. The rate of grafting was determined by changing [monomerl], [thiourea], [initiator], acidity of the medium, reaction medium, and temperature. A significant increase percent of grafting was noticed with increasing monomer concentration to 84.49 × 10^?2 mole/liter and the further increase is associated with the decrease of graft yield. The graft yield increases with an increase of thiourea (Tu) concentration to 25 × 10^?5 mole/liter; then it decreases. A measurable increase in graft yield was observed with an increase in acidity of the medium. Graft yield increases to a certain temperature, i.e., 50°C, and then it decreases. The graft yield increases with an increase of initiator concentration to 60 × 10^?4 mole/liter; then it decreases. The graft yield is medium dependent. A suitable kinetic path has been proposed and the rate equation has been derived.     

Addition–fragmentation chain transfer: Molecular weight distributions and retardation in the system methyl methacrylate/methyl α‐(bromomethyl)acrylate

A detailed investigation of addition–fragmentation chain transfer (AFCT) in the free‐radical polymerization of methyl methacrylate (MMA) in the presence of methyl α‐(bromomethyl)acrylate (MBMA) was carried out to elucidate mechanistic details with efficient macromonomer synthesis as an underlying goal. Advanced modeling techniques were used in connection with the experimental work. Curve fitting of simulated and experimental molecular weight distributions with respect to the rate coefficient for addition of propagating radicals to MBMA (k_add) over 60–120 °C resulted in E_add = 21.7 kJ mol^?1 and A_add = 2.18 × 10⁶ M^?1 s^?1 and a very weak temperature dependence of the chain‐transfer constant (E_add ≈ E_p). The rate coefficient for fragmentation of adduct radicals at 60 °C was estimated as k_f ≈ 39 s^?1 on the basis of experimental data of the MMA conversion and the concentration of 2‐carbomethoxy‐2‐propenyl end groups. The approach developed is generic and can be applied to any AFCT system in which copolymerization does not occur and in which the resulting unsaturated end groups do not undergo further reactions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2640–2650, 2004     

Grafting onto wool. IV. Interaction of polymer radicals in the viscous media of wool fibers

In order to study the termination reaction of polymer radicals in the viscous media of wool fibers, reduced, methylated, and S-carboxymethylated wool fibers were used for graft copolymerization of methyl methacrylate and styrene. With termination of poly(methyl methacrylate) radicals, two different termination reactions, recombination and disproportionation, were together involved in the grafting systems studied. The occurrences of two termination reactions in the system could be correlated with the mobility of the wool chain controlling the radical end mobility. With decreasing disulfide content in the fibers, disproportionation predominantly takes place among the mobilized chains. At a constant disulfide, the thiol content or the concentration of thiol anions becomes the determining factor for the termination reaction. A possible explanation for these phenomena in terms of the thiol and disulfide interchange reaction is presented. On the grafting of styrene, additional evidence was obtained that prevention and retardation of the interchange reactions followed mechanochemical bond scission of the disulfide and other covalent bonds and produced new free radicals which could initiate chain reactions.     

Viscosity effects in cobaloxime‐mediated catalytic chain‐transfer polymerization of methacrylates

The effect of bulk viscosity on the cobaloxime‐mediated catalytic chain‐transfer polymerization of methacrylates at 60 °C was investigated by both the addition of high molecular weight poly(methyl methacrylate) to methyl methacrylate polymerization and the dilution of benzyl methacrylate polymerization by toluene. The results indicate that the bulk viscosity is not directly linked to the chain‐transfer activity. The previously measured relationship between chain‐transfer‐rate coefficient and monomer viscosity therefore probably reflects changes at the molecular level. However, the results in this article do not necessarily disprove a diffusion‐controlled reaction rate because cobaloxime diffusion is expected to scale with the monomer friction coefficient rather than bulk viscosity. Considering the published data, to date we are not able to distinguish between a diffusion‐controlled reaction rate or a mechanism directly affected by the methacrylate substituent. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 782–792, 2002; DOI 10.1002/pola.10152     

Studies on some radical transfer reactions by entrapping the radicals as polymer end groups. I. Reaction of hydroxyl radicals with amines

The reaction of OH radicals with a number of amines has been studied by entrapping the resultant radicals as polymer end groups which have been detected and estimated by the sensitive dye partition technique. Expressions have been developed relating the average amounts of end groups per polymer molecule to the rate constant of the radical transfer reaction, the rate constants determined for reaction with n-butyl, n-hexyl, and n-octyl amine being 1.00 × 10¹⁰, 1.31 × 10¹⁰, and 1.46 × 10¹⁰ mol^?1 L s^?1, respectively, at 25°C. The order of reactivity for amines of different classes has been found to be as primary < secondary > tertiary, the rate constants for reaction with n-butyl, dibutyl, and tributyl amine being 1.00 × 10¹⁰, 1.81 × 10¹⁰, and 1.67 × 10¹⁰ mol^?1 L s^?1, respectively, at 25°C. The change in the reactivity of the amine with chain length and amine class has been explained by activation and deactivation of the CH₂ group from which H abstraction by OH radicals occurs, respectively, by the alkyl group and by the protonated amino nitrogen under the acidic condition of the medium. Between pH 1.00 and 2.17, the rate of the reaction with n-butyl amine remains practically unchanged, but from pH 2.20 to 2.72 the rate constant increases with increasing pH, indicating that deprotonation of the positively charged nitrogen starts at about pH 2.20. The method is simple and accurate and can be applied to detect and estimate very reactive radicals.     

FURTHER STUDY OF ALLYL ETHERS AND RELATED COMPOUNDS AS TRANSFER AGENTS IN RADICAL POLYMERIZATIONS

Allyl glycidyl ether (AGE), allyl 1,1,2,3,3,3-hexafluoropropyl ether (AFE), allyl 2-naphthyl ether (ANE), 2-vinyl-1,3-dioxolane (2VD) and allyl alcohol (AA) have been examined as transfer agents in the radical polymerization of methyl methacrylate (MMA) at 60°C; the transfer constants are 1.1 × 10^?3, 0.1 × 10^?3, 0.2 × 10^?3, 1.1 × 10^?3 and 0.6 × 10^?3, respectively. AFE and AA barely affect the rate of polymerization: AGE, ANE, and 2VD act as weak retarders. There is no direct correlation between effectiveness as a transfer agent and the extent of retardation for these additives. For copolymerization with MMA (monomer-1), the monomer reactivity ratios r₁ are 42 ± 5 and 32 ± 5 for AGE and ANE, respectively; for both cases, r₂ is very close to zero; 2VD engages in copolymerization with MMA to a negligible extent. Experiments involving styrene or acrylonitrile gave results consistent with those obtained using MMA.     

Determination of chain transfer constant to dodecanethiol in styrene/methyl methacrylate and butyl acrylate/methyl methacrylate copolymerization and effect of chain length on composition and stereochemical configuration of copolymers

Free radical copolymerization of styrene/methyl methacrylate (S/MMA) and butyl acrylate/methyl methacrylate (BA/MMA) in the presence of n-dodecanthiol (DDT) has been studied at 60°C in a 3 mol/L benzene solution using 2,2′-azobis(isobutyronitrile) (AIBN) as initiator. Overall chain transfer constant to DDT has been determined for both copolymerization systems, as a function of monomer feed composition using complete molecular weight distribution and the Mayo method. Overall transfer coefficients have values which are dependent on both monomer feed composition and individual comonomer transfer values. Composition, sequence distribution, and stereoregularity of copolymers obtained are, in our experimental conditions, independent of copolymer molecular weight. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2913–2925, 1998