Experimental analysis of metal coated dielectric waveguides

This paper concerns the experimental characteristics of metal coated dielectric waveguides with a rectangular surface corrugation. Waveguide are designed to operate at a second Bragg frequency of 90 GHz. The period, height and the duty cycle of a rectangular grating were calculated using the chosen frequency. A metallic layer of aluminum is sputtered on one side of the slab waveguide. The purpose of the metallic layer is to simulate a layer of high density plasma on the surface of the waveguide similar to that obtained by optical excitation of semiconductor structures. Experiments were performed to examine the far field radiation pattern, attenuation constant and the dispersion relation. Due to the presence of the plasma layer there will be an angular shift in the far field radiation pattern. We have observed angular shifts of about 20 in the radiation pattern of the waveguide before and after coating. Measurements are made in the frequency range of 88–95 GHz. This waveguide structure can be used to design an electronically steerable antenna and an electronic phase shifter operating in the millimeter-wave frequency band.Supported in part by the Army Research Office.     

W波段带状注矩形单栅返波振荡器模拟研究

提出并研究了一种带状电子注矩形单栅返波振荡器。首先研究了矩形单栅慢波结构的色散特性和耦合阻抗特性,然后粒子模拟并优化设计了带状注矩形单栅高频结构,预群聚腔及输出一体化结构。研究结果表明:利用电压200kV、电压2kA、截面为24mm×0.5mm的带状电子注,驱动该矩形单栅返波振荡器,能够产生42 MW的输出功率,工作频率86GHz,效率为10.5%。     

Electromagnetic field and dispersion characteristic analysis of absorbing onion-like carbon tube waveguides

Here, we present our calculation results of the electromagnetic field distributions and the dispersion characteristics of open cylindrical tube waveguides. The analyzed waveguides are made of the onion-like carbon (OLC) material. The solution of the boundary problem was fulfilled by the partial area method (Nickelson et al. in electrodynamical analysis of open lossy metamaterial waveguide and scattering structures. InTech, UK, pp 27–58 [1]). We have determined the complex roots of the dispersion equation using of the Muller method. It discovered the very complicated dependencies of the phase and attenuation constants on the waveguide radii. Such dependencies arise because the OLC material is the highly dispersive and absorbing one. We have investigated the high-frequency cutoff frequency of the propagating hybrid modes HE₁₁ and HE₁₂ dependent on the tube waveguide external and internal radii. We found that it is possible to reach the one-mode regime of OLC tube waveguide.     

折叠矩形槽波导行波管输入输出过渡波导

为了将槽波导端与标准矩形波导相连接,设计了一种适用于折叠槽波导结构行波管的输入输出过渡波导, 可将其视为槽宽渐变的双槽加载矩形波导。利用电磁仿真软件CST微波工作室对该结构进行仿真计算,讨论了各个结构参数对其性能的影响。对比了直线渐变、抛物线渐变和指数渐变3种槽宽渐变规律在W波段对其传输特性及损耗特性的影响。研究结果表明:指数渐变结构的驻波系数小于1.15的带宽比其他两种结构都要宽,且在90~99 GHz、驻波系数小于1.25时,该结构的整体长度也远小于另外两种结构,能够实现良好的过渡效果; 而直线渐变结构的损耗在90~97 GHz为最低。     

Dispersion parameters and nonlinear optical properties of silicon nitride rib waveguides

Silicon nitride rib waveguides are numerically studied by use of a full-vectorial mode solver program based on finite difference method. Dispersion parameters, up to the third-order, are computed for waveguides of heights 0.8 μm, 0.9 μm, and 1 μm. Like silicon-on-insulator waveguides, silicon nitride rib waveguides allow us to tailor dispersion parameters at telecom wavelengths. Deeply-etched silicon nitride rib waveguides of height up to 1.5 μm are investigated for correct geometries to achieve polarization independence. The computations lead to a minimum etch depth which can be written as linear function of the waveguide height. Etch-depth and waveguide height dependencies of the nonlinear refractive index coefficient of the silicon nitride are studied. It is shown that third-order optical nonlinearities in silicon nitride rib waveguides can be enhanced by suitable choices of waveguide parameters.     

Dispersion characteristics of asymmetric coupled anisotropic dielectric waveguides using FDFD

The formulation is developed in the frequency domain and the finite difference method is used for the numerical solution of the scalar wave equation, written in terms of the transverse components of the magnetic field. As a result a conventional eigenvalue problem is obtained without the presence of spurious modes due to the implicit inclusion of the divergence of the magnetic field equal to zero. The formulation is developed to include biaxial anisotropic dielectrics with an index profile varying arbitrarily in the cross section of the waveguide under analysis. This formulation is then applied to the analysis of the influence on the dispersion characteristics of the dimensions of asymmetric coupled rectangular uniaxial anisotropic dielectric waveguides. As expected, the reduction of the height or the width of one of the rectangular dielectric waveguides causes the dispersion curves to move towards higher frequencies.     

利用双阶梯波导层对深紫外激光二极管的性能优化

在深紫外激光二极管中,波导层的作用是用来传输并限制光束.传统的深紫外激光二极管存在很强的极化感应电场,这种电场能够降低深紫外激光二极管的光电性能.本文提出了一种新型双阶梯型上波导层(UWG)和下波导层(LWG),可以提高半导体激光器的性能.通过使用Crosslight软件将矩形、单阶梯型和双阶梯型波导层三种不同的结构进行仿真研究,比较三种结构器件的能带图、电子空穴浓度、辐射复合率、P-I以及V-I特性等.结果表明,新型双阶梯波导层结构的应用增加了电子有效势垒的高度,缓解了电子阻挡层的能带弯曲,减小了极化电场的影响,从而提升了该器件的光学和电学性能.     

Spectrally selective splitters with metal-dielectric-metal surface plasmon waveguides

Spectrally selective splitters with metal-dielectric-metal (MDM) subwavelength waveguides are proposed in this paper. The method is based on the Bragg grating structure with periodically modulated MDM waveguide width, which delivers a stop band effect for the surface plasmon propagating in the waveguide. By adding appropriate Bragg grating structure in one or more arms of the waveguide splitters, light in a certain frequency range can be readily guided into the desired directions, as demonstrated numerically by the finite-difference time-domain method. Dependence and optimization of the geometrical parameters are also considered in this paper.     

具有任意槽的矩形波导栅慢波结构高频特性的研究

将任意形状槽的连续轮廓近似用一系列相连的矩形阶梯近似，利用各阶梯面上导纳的匹配，以及槽与互作用区边界场的连续与匹配条件，获得了具有任意槽的矩形波导栅慢波结构的色散方程和耦合阻抗的表达式，并进行理论上的验证.加工制作了矩形槽波导栅模型，冷测表明理论值与测量值相吻合.分别求解几种特殊槽形矩形波导栅慢波结构的色散特性及耦合阻抗，其中，三角形结构的色散和耦合阻抗均最弱，而倒梯形结构色散最强，耦合阻抗最大. 关键词： 矩形波导栅 任意槽 色散特性 慢波结构     

DIELECTRIC EFFECT ON THE RADIO-FREQUENCY CHARACTERISTICS OF A RECTANGULAR WAVEGUIDE GRATING TRAVELING WAVE TUBE

A new type of partial-dielectric-loaded rectangular waveguide grating slow-wave structure (SWS) for millimeter wave traveling wave tube (TWT) is presented in this paper. The radio-frequency characteristics including the dispersion properties, the longitudinal electric field distribution and the beam-wave coupling impedance of this structure are analyzed. The results show that the dispersion of the rectangular waveguide grating circuit is weakened, the phase velocity is reduced and the position of the maximum E _z is basically invariant after partially filling the dielectric materials in the rectangular waveguide grating SWS. Although the coupling impedance decreases a little, it still keeps above 40 Ω.     

磁光平面波导的单向传播特性

表面磁等离子体(surfacemagnetoplasmons,SMPs)是一种在电介质和偏置磁场作用下磁光材料界面处传播的近场电磁波.其独特的非互易传播特性引起了大量科研工作的关注,但在具体的波导结构设计上仍存在很多问题.本文研究了一种银-硅-磁光材料的3层平面波导结构,SMPs在磁光材料和硅的界面处传播,发现在特定的频率范围内,SMPs的基模及高阶模式均具有正向或反向的单向传播特性.分别计算了旋磁与旋电材料平面波导的色散方程,研究了硅层厚度与外加磁场对能带结构及SMPs单向传播区域的影响,发现无论是旋磁或旋电材料的结构,硅层厚度的增加使高阶模式使高阶模式出现在更低的频率位置,使单向传输带宽变小甚至消失,外加磁场的变大使磁光材料的能带结构频率增大的同时带隙中也引入了高阶模式.计算了2种磁光材料平面波导的正向和反向的单向传播带宽宽度,发现旋磁材料YIG的单向SMPs模式出现在GHz波段,最大单向带宽可达到2.45 GHz;旋电材料InSb的单向SMPs模式出现在THz波段,最大单向带宽达到3.9 THz.     

左手介质矩形波导导模和表面模的场分布

从麦克斯韦方程组出发,结合电磁场的边界条件,推导出介质矩形波导导模的一般色散方程.对普通介质矩形波导和左手介质矩形波导的导模场分布分别进行了数值模拟.通过对比两种介质矩形波导的导模场分布的模拟结果,发现左手介质矩形波导Ex22模的场分布比普通介质波导Ex00模的场更集中在波导中部.同时,根据处理普通介质矩形波导的Marcatili方法.类比得到左手介质矩形波导表面模的色散方程,并数值模拟了低阶模的场分布,结果表明,能量主要集中在波导的四个角区以及波导的边缘.     

An Open Rectangular Waveguide Grating for Millimeter-Wave Traveling-Wave Tubes

Millimeter-wave traveling-wave tube(TWT) prevails nowadays as the amplifier for radar,communication and electronic countermeasures.The rectangular waveguide grating is a promising all-metal interaction circuit for the millimeter-wave TWT with advantages of high power capacity,fine heat dissipation,scalability to smaller dimensions for shorter wavelengths,compact structure and robust performance.Compared with the traditional closed structure,the open rectangular waveguide grating(ORWG) has wider bandwidth,lower cut-off frequency,and higher machining precision for higher working frequencies due to the open transverse.It is a potential structure that can work in the millimeter wave and even Terahertz band.The rf characteristics including dispersion and interaction impedance are investigated by both theoretic calculation and software simulation.The influences of the structure parameters are also discussed and compared,and the theoretical results agree well with the simulation results.Based on the study,the ORWG will favor the design of a broadband and high-power millimeter-wave TWT.     

Photonic band-gap enhanced second-harmonic generation in a planar lithium niobate waveguide

Enhanced second-harmonic generation (SHG) conversion efficiency was theoretically predicted in waveguide geometry with coupling to a one-dimensional grating photonic band gap (PBG). We report a series of experiments using samples made with lithium niobate. A waveguide was fabricated near the surface by applying the proton-exchange technique. The characteristics of waveguide modes were determined by several techniques: prism coupling, diffraction, and Cherenkov radiation. The WKB method was used to analyze the results. Ultraviolet laser lithography was applied to make PBG gratings on the sample. We further investigated Cherenkov second-harmonic generation (CSHG), i.e., SHG radiated into the substrate, under the condition of a band-edge PBG resonance in the waveguides. The SHG inside planar waveguides was also experimentally investigated. We fabricated waveguides with multiple pump modes and found that the second mode was more efficient in enhancing the second harmonic signal. This result is explained by our model. Several samples were investigated in detail; the highest conversion efficiency of CSHG with a PBG was enhanced around 50 times above the CSHG signal without a PBG. A numerical model was constructed with parameters calculated from our sample characterization data to interpret the experimental results.     

Dispersion properties of high-contrast grating hollow-core waveguides

We present unique dispersion characteristics of high-contrast grating (HCG) hollow-core waveguides and show that slow light can be facilitated using internal resonances developing inside the waveguide walls. In addition, we show a fast and precise method of inferring the dispersion information from the waveguide angular reflectivity spectrum.     

Grating couplers for thick SOI rib waveguides

The use of grating couplers in high index contrast waveguides like silicon on insulator (SOI) offers several advantages over other coupling approaches, including better alignment tolerances and allowing for wafer-scale testing. The grating couplers were developed for nanometric SOI waveguides (Si-wires), and recently also for micrometric rib waveguides. In this paper we review our work in fiber-to-chip grating couplers for thick SOI rib waveguides, where a coupling efficiency of ?2.2?dB was demonstrated experimentally. We also discuss the use of grating couplers to improve optical throughput (étendue) of a planar waveguide Fourier-Transform (FT) spectrometer implemented in thick rib waveguides.     

K-Na离子交换单模平面波导的制备及其表征

通过K-Na离子交换技术制备了多模玻璃平面波导.采用棱镜耦合技术测量了波导的有效折射率,用IWKB方法拟合得到K-Na离子交换波导的折射率分布符合高斯分布,由色散曲线得到单模波导的制备条件(即扩散深度范围),从而得出单模波导的离子交换时间范围,制备出单模波导,并通过求解WKB色散方程得出单模波导的表面折射率.用普通数码相机,通过对离子交换平面玻璃光波导传输线进行数字成像,根据传输线上的光强分布拟合出光强传输衰减曲线,计算出单模波导的传输损耗大约为0.4 dB/cm.     

Optical filter based on subtractive dispersion planar reflective gratings

We have successfully designed, fabricated, and tested an optical filter based on cascaded planar reflective gratings. The device uses a combination of two grating elements arranged in a subtractive dispersion configuration. The first grating demultiplexes a 300 nm wide band and drops optical channels at 1490 and 1550 nm, commonly used in passive optical networks. The second grating completely counter-balances the dispersion properties of the first grating and ultimately yields zero dispersion in the output waveguide. Such a configuration allows the transmission of optical signals though the device in an ultra-wide band spanning 1250-1410 nm. The filter was manufactured using an industry standard silica-on-silicon process which was augmented with grating facet formation and metallization. In spite of using low refractive index contrast waveguides (0.82%), the device had a remarkably low footprint of only 0.21 cm². Applications of the device in passive optical networks are discussed.     

基于表面等离子体的太赫兹光束方向调控的模拟研究

本文根据锑化铟(InSb)材料在THz波段下复介电常数对温度的响应特性,采用了带有光栅的锑化铟-介质-锑化铟的表面等离子体波导结构,实现了1THz频率光束的准直出射,并能够通过调整结构两侧光栅的温度差来控制出射光束的角度.由时域有限差分方法得到光束偏转角度与温度差之间的关系.理论上利用表面等离子体波导模式的光栅耦合机理解释光束方向改变的原因. 关键词： 表面等离子体 太赫兹 时域有限差分方法 光束方向控制     

New method for calculating the spectra and radiation losses of leaky waves in multilayer optical waveguides

The efficiency of a new method for calculating the spectrum and attenuation coefficient of leaky electromagnetic modes is demonstrated with multilayer planar optical waveguides the guiding properties of which are determined by antiresonant reflection from the multilayer cladding (antiresonant reflecting optical waveguides) rather than by total internal reflection from the core-cladding interface as in standard optical waveguides. The new method applies to calculation of both electromagnetic modes in dielectric waveguides and electron quantum states in multibarrier semiconductor heterostructures. The characteristics of multilayer waveguides calculated by the new method are compared with published data obtained from a complex dispersion relation by the transfer matrix method. As an example, the wavelength dependence of the radiation losses for the first TE mode of a planar optical waveguide containing 52 pairs of layers is calculated.