Studies on structural and electrical properties of Mg<Subscript>0. 5+y</Subscript> (Zr<Subscript>2-y</Subscript>Fe<Subscript>y</Subscript>) <Subscript>2</Subscript> (PO<Subscript>4</Subscript>) <Subscript>3</Subscript> ceramic electrolytes

The sample of Mg_{0. 5+y} (Zr_1-y Fe_y) ₂ (PO₄) ₃ (0.0 ≤y ≤0.5) was synthesized using the sol-gel method. The structures of the samples were investigated using X-ray diffraction and Fourier transform infrared spectroscopy measurement. XRD studies showed that samples had a monoclinic structure which was iso-structured with the parent compound, Mg_0.5Zr (PO₄) ₃. The complex impedance spectroscopy was carried out in the frequency range 1–6 MHz and temperature range 303 to 773 K to study the electrical properties of the electrolytes. The substitutions of Fe³⁺ with Zr⁴⁺ in the Mg_0.5Zr (PO₄) ₃ structure was introduced as an extrainterstitial Mg²⁺ ion in the modified structured. The compound of Mg_0.5+y (Zr_1-y Fe_y)₂(PO₄)₃ with y?=?0.4 gives a maximum conductivity value of 1.25?×?10^?5 S cm^?1 at room temperature and 7.18?×?10^?5 S cm^?1 at 773 K. Charge carrier concentration, mobile ion concentration, and ion hopping rate are calculated by fitting the conductance spectra to power law variation, σ _ac (ω)?=?σ _o ? +?Aω ^α . The charge carrier concentration and mobile ion concentration increases with increase of Fe³⁺ inclusion. This implies the increase in conductivity of the compounds was due to extra interstitial Mg²⁺ ions.     

Infralow-frequency dielectric response of Pb<Subscript>3</Subscript>O<Subscript>4</Subscript> polycrystalline layers

This paper reports on the results of the investigation into the frequency dispersion of the capacitance and dielectric loss in capacitor structures based on red lead Pb₃O₄. It is established that, in the range of frequencies f = 1.50 × 10^?3?0.25 Hz, the capacitance decreases and the dielectric loss tangent increases with increasing frequency. The frequency dependence of the electrical conductivity in an alternating-current electric field indicates the applicability of the hopping model of charge transfer under normal conditions. The role of a lone electron pair of Pb²⁺ cations in dielectric polarization is discussed.     

Charge carrier mobility in crystals of the Pb<Subscript>0.67</Subscript>Cd<Subscript>0.33</Subscript>F<Subscript>2</Subscript> superionic conductor

The frequency (ν = 10^?1–10⁷ Hz) dependences σ(ν) of the conductivity of single crystals of the Pb_0.67Cd_0.33F₂ superionic conductor with the fluorite-type structure (CaF₂) in the temperature range of 132–395 K have been studied. The dependences σ(ν) have been discussed in the framework of the hopping relaxation of ionic carriers, which are mobile anions F^?. From experimental curves σ(ν), the direct-current (dc) conductivity σ_dc and the average charge carrier hopping frequency ν_h have been determined. This has made it possible to calculate the charge carrier mobility μ_mob and charge carrier concentration n _mob in these crystals. At room temperature (293 K), the electrical parameters are σ_dc = 1.6 × 10^?4 S/cm, ν_h = 2.7 × 10⁷ Hz, μ_mob = 2.0 × 10^?7 cm²/(s V), and n _mob = 5.1 × 10²¹ cm^?3.     

Thermopower in the region of hopping conduction in TlNiS<Subscript>2</Subscript>

Samples of the composition TlNiS₂ in the hexagonal system with the unit cell parameters a=12.28 Å, c=19.32 Å, and ρ=6.90 g/cm³ are synthesized. The results of the investigation into the electrical and thermoelectrical properties of TlNiS₂ samples in the temperature range 80–300 K indicate that TlNiS₂ is a p-type semiconductor. It is found that, at temperatures ranging from 110 to 240 K, TlNiS₂ samples in a dc electric field possess variable-range-hopping conduction at the states localized in the vicinity of the Fermi level. The density of localized states near the Fermi level is determined to be N_F=9×10²⁰ eV^?1 cm^?3, and the scatter of the states is estimated as J≈2×10^?2 eV. In the temperature range 80–110 K, TlNiS₂ exhibits activationless hopping conduction. At low temperatures (80–240 K), the thermopower of TlNiS₂ is adequately described by the relationship α(T)=A+BT, which is characteristic of the hopping mechanism of charge transfer. In the case when the temperature increases to the temperature of the onset of intrinsic conduction with the activation energy ΔE=1.0 eV, there arise majority intrinsic charge carriers of both signs. This leads to an increase in the electrical conductivity σ and, at the same time, to a drastic decrease in the thermopower α; in this case, the thermopower is virtually independent of the temperature.     

Conduction through localized states in a single crystal of the TlGa<Subscript>0.5</Subscript>Fe<Subscript>0.5</Subscript>Se<Subscript>2</Subscript> alloy

Layered single crystals of the TlGa_0.5Fe_0.5Se₂ alloy in a dc electric field at temperatures ranging from 128 to 178 K are found to possess variable-range-hopping conduction along natural crystal layers through states localized in the vicinity of the Fermi level. The parameters characterizing the electrical conduction in the TlGa_0.5Fe_0.5Se₂ crystals are estimated as follows: the density of states near the Fermi level N_F = 2.8 × 10¹⁷ eV^?1 cm^?3, the spread in energy of these states ΔE = 0.13 eV, the average hopping length R_av = 233 Å, and the concentration of deep-lying traps N _t = 3.6 × 10¹⁶ cm^?3.     

Mechanisms of low-temperature high-frequency conductivity in systems with a dense array of Ge<Subscript>0.7</Subscript>Si<Subscript>0.3</Subscript> quantum dots in silicon

High-frequency (HF) conductivity in systems with a dense (with a density of n = 3 × 10¹¹ cm^?2) array of self-organized Ge_0.7Si_0.3 quantum dots in silicon with different boron concentrations n_B is determined by acoustic methods. The measurements of the absorption coefficient and the velocity of surface acoustic waves (SAWs) with frequencies of 30–300 MHz that interact with holes localized in quantum dots are carried out in magnetic fields of up to 18 T in the temperature interval from 1 to 20 K. Using one of the samples (n_B = 8.2 × 10¹¹ cm^?2), it is shown that, at temperatures T ≤ 4 K, the HF conductivity is realized by the hopping of holes between the states localized in different quantum dots and can be explained within a two-site model in the case of

Open image in new window

, where ω is the SAW frequency and τ₀ is the relaxation time of the populations of the sites (quantum dots). For T > 7 K, the HF conductivity has an activation character associated with the diffusion over the states at the mobility threshold. In the interval 4 K < T < 7 K, the HF conductivity is determined by a combination of the hopping and activation mechanisms. The contributions of these mechanisms are distinguished; it is found that the temperature dependence of the hopping HF conductivity approaches saturation at T* ≈ 4.5 K, which points to a τ₀ ≤ 1. A value of τ₀(T*) ≈ 5 × 10^?9 s is determined from the condition ωτ₀(T*) ≈ 1.

     

Charge transport in PbMoO<Subscript>4</Subscript> crystals

Dc and ac electrical conductivity of lead molybdate crystals is studied in the temperature range 300–550 K. The electrical conductivity was shown to have electronic (hole) impurity character. The I–V characteristics are typical of a space charge-limited current. The carrier mobility was estimated to be 10^?5 cm² V^?1 sat T=300 K. The results of the study suggest the hopping mechanism of conduction in PbMoO₄ crystals.     

Relaxation phenomena in TlGa<Subscript>0.99</Subscript>Fe<Subscript>0.01</Subscript>Se<Subscript>2</Subscript> single crystals

The relaxation electronic phenomena occurring in TlGa_0.99Fe_0.01Se₂ single crystals in an external dc electric field are investigated. It is established that these phenomena are caused by electric charges accumulated in the single crystals. The charge relaxation at different electric field strengths and temperatures, the hysteresis of the current-voltage characteristic, and the electric charge accumulated in the TlGa_0.99Fe_0.01Se₂ single crystals are consistent with the relay-race mechanism of transfer of a charge generated at deep-lying energy levels in the band gap due to the injection of charge carriers from the electric contact into the crystal. The parameters characterizing the electronic phenomena observed in the TlGa_0.99Fe_0.01Se₂ single crystals are determined to be as follows: the effective mobility of charge carriers transferred by deep-lying centers μ_f=5.6×10^?2 cm²/(V s) at 300 K and the activation energy of charge transfer ΔE=0.54 eV, the contact capacitance of the sample C _c =5×10^?8 F, the localization length of charge carriers in the crystal d _c =1.17×10^?6 cm, the electric charge time constant of the contact τ=15 s, the time a charge carrier takes to travel through the sample t _t =1.8×10^?3 s, and the activation energy of traps responsible for charge relaxation ΔE _σ = ΔE _Q = 0.58 eV.     

CeAlO<Subscript>3</Subscript> crystals: Preparation and study of their electrical and optical characteristics

Crystals of cerium aluminate with perovskite structure were obtained using the cold-crucible technique. The electrical and optical properties of cerium aluminate were studied in air in the range 300–1300 K. The main characteristics of CeAlO₃ at T=300 K are a follows: electrical conductivity σ=10^?7 S/cm, dielectric permittivity ?=3000–10000 (both measured at a frequency of 1000 Hz), thermal band-gap width ΔE=2.3±0.5 eV, and optical width δE=2.65±0.25 eV, which decreases at a rate of ?0.62×10^?3 eV/K with increasing temperature in the 300-to 1500-K interval.     

Electrical characterization of porous La-doped BaSnO<Subscript>3</Subscript> using impedance spectroscopy

A few compositions in the system Ba_1???x La _x SnO₃ (x?=?0.00, 0.01, 0.05, and 0.10) have been synthesized via the solid state ceramic route. The synthesized powders have been characterized using X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, Raman spectroscopy, Fourier transformation infrared, thermogravimetrical analysis, and differential thermal analysis techniques. The powder X-ray diffraction pattern of the samples confirms the formation of a single-phase solid solution only up to 0.50?≤?x. It was found that all the samples have a cubic crystal structure. The electrical properties of La-modified BaSnO₃ were studied using ac impedance spectroscopy technique over a wide range of temperatures (50–650 °C) in the frequency range of 10 Hz–13 MHz. The complex impedance plots above 300 °C show that total impedance is due to the contributions of grain and grain boundaries. The resistance of these contributions has been determined. Variation of these resistances with temperature shows the presence of two different regions with different slopes. The nature of the variation of conductivity of the grain and grain boundaries is different in different regions. Based on the value of activation energy, it is proposed that conduction via hopping of doubly ionized oxygen vacancies (V_O ^??) is taking place in the temperature region of 300–450 °C, whereas in the temperature region of 450–650 °C, it is due to proton, i.e., OH^? ions, hopping.     

Specific features of anion transfer in HoF<Subscript>3</Subscript> crystals at high temperatures

The anionic conductivity of HoF₃ single crystals with a β-YF₃ structure (orthorhombic crystal system, space group Pnma) is investigated over a wide range of temperatures (323–1073 K). The unit cell parameters of HoF₃ crystals are as follows: a=0.6384±0.0009 nm, b=0.6844±0.0009 nm, and c=0.4356±0.0005 nm. It is revealed that the conductivity anisotropy of the HoF₃ crystals is insignificant over the entire temperature range covered. The crossover from one mechanism of ion transfer to another mechanism is observed near the critical temperature T_c≈620 K. The activation enthalpy of electrical conduction is found to be ΔH₁=0.744 eV at T<T_c and ΔH₂=0.43 eV at T>T_c. The fluorine vacancies are the most probable charge carriers in HoF₃ crystals. The fluorine ionic conductivities at temperatures of 323, 500, and 1073 K are equal to 5×10^?10, 5×10^?6, and 2×10^?3 S cm^?1, respectively.     

Internal friction of Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript> single crystals

This paper reports on the results of measurements of the internal friction Q^?1 and the shear modulus G of Li₂B₄O₇ single crystals along the crystallographic directions [100] and [001] in the temperature range 300–550 K for strain amplitudes of (2–10)×10^?5 at infralow frequencies. The anomalies observed in Q^?1 and G in the temperature range 390–410 K are due to thermal activation of the mobility of lithium cations and their migration from one energetically equivalent position to another. A jump in the internal friction background is revealed in the vicinity of the Q^?1 and G anomalies for the Li₂B₄O₇ crystal. The magnitude of this jump depends on the crystallographic direction.     

Spectroscopic diagnostics of a laser erosion plasma formed from CuSbS<Subscript>2</Subscript> polycrystals

The spectra and dynamics of emission from regions of a laser plasma torch located at different distances from a polycrystalline CuSbS₂ target irradiated by a neodymium laser (W=(3–5)×10⁸ W/cm², ?=20 ns, f=12 Hz, 73x03BB;=1.06μm) were investigated. The emission data were used to estimate the average temperature (≤0.82 eV) and the electron density ((1.82?1.92)×10¹⁶ cm^?3) in the laser torch and the recombination times of ions (t _r(S²⁺)=15 ns, t _r(Cu⁺)=65?85 ns), as well as to analyze the efficiency of filling of excited atomic levels. A model describing the target destruction and the evolution of the processes accompanying spread of the laser plasma is proposed.     

AC conductivity and mechanism of conduction study of lithium barium pyrophosphate Li<Subscript>2</Subscript>BaP<Subscript>2</Subscript>O<Subscript>7</Subscript> using impedance spectroscopy

The Li₂BaP₂O₇ compound has been obtained by the conventional solid-state reaction and characterized by X-ray powder diffraction. The title material crystallizes in the monoclinic system with C2/c space group. Electrical properties of the compound have been studied using complex impedance spectroscopy in the frequency range 200 Hz–5 MHz and temperature range 589–724 K. Temperature dependence of the DC conductivity and modulus was found to obey the Arrhenius law. The obtained values of activation energy are different which confirms that transport in the titled compound is not due to a simple hopping mechanism. AC conductivity measured follows the power-law dependence σ _AC?～?ω ^s typical for charge transport. Therefore, the experimental results are analyzed with various theoretical models. Temperature dependence of the power law exponent s strongly suggests that tunneling of large polarons is the dominant transport process.     

Charge transfer over localized states in a TlS single crystal

It is revealed that TlS single crystals exhibit a variable range hopping conduction along a normal to their natural layers at temperatures T ≤ 230 K in a dc electric field and a nonactivated hopping conduction at low temperatures in strong electric fields. Estimates are made for the density of states near the Fermi level (N _F = 2.8 × 10²⁰ eV^?1 cm^?3 and their energy spread (ΔW = 0.02 eV), the localization radius (a = 33 Å), the average jump distance in the region of activated (R _av(T) = 40 Å) and nonactivated (R _av(F) = 78 Å) hopping conduction, and also the drop in the charge carrier potential energy along the jump distance in an electric field F: eFR = 0.006 and 0.009 eV at F = 7.50 × 10³ and 1.25 × 10⁴ V/cm, respectively.     

<Emphasis Type="Italic">K</Emphasis><Subscript><Emphasis Type="Italic">e</Emphasis>3</Subscript> Decay Studies in the OKA Experiment

Recent results from OKA setup concerning form factor studies in K_e3 decay are presented. About 5.25 M events obtained for decays of 17.7 GeV/cK⁺ are selected for the analysis. The linear and quadratic slopes for the decay form factor f₊(t) are measured: λ'₊ = 2.95 ± 0.022 ± 0.018 × 10 ^-2 for the linear slope fit and λ₊ = 2.611 ± 0.035 ± 0.028 × 10 ^-2, λ"₊ = 1.91 ± 0.19 ± 0.14 × 10 ^-3 for the quadratic one. The scalar and tensor contributions are compatible with zero. Several alternative parametrizations are tried: the Pole fit parameter is found to be M _V = 891 ± 3 MeV; the parameter of the dispersive parametrization is measured to be Λ₊ = 2.458 ± 0.018 × 10^-2.     

AC and DC conductivity study of LiH<Subscript>2</Subscript>PO<Subscript>4</Subscript> compound using impedance spectroscopy

The lithium dihydrogen phosphate LiH₂PO₄ has been investigated by X-ray powder diffraction, scanning electron microscopy (SEM), and electrical impedance spectroscopy. The Rietveld refinements based on the XRD patterns show that the compound is crystallized in the orthorhombic system with Pna2₁ space group, and the refined unit cell parameters are a = 6.2428 Å, b = 7.6445 Å, and c = 6.873 Å. The electrical properties were studied using complex impedance spectroscopy as a function of frequency (10⁴–10⁷ Hz) at various temperatures (300–400 K). The Nyquist plots are well fitted to an equivalent circuit consisting of a series of combination of grains and inhomogeneous electrode surface effect. The frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. Moreover, the near value of the activation energies obtained from the equivalent circuit and analysis of M″ confirms that the transport is through ion hopping mechanism dominated by the motion of the proton in the structure of the investigated material.     

Lithium diffusion in Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>-based electrodes: a joint analysis of electrochemical impedance,cyclic voltammetry,pulse chronoamperometry,and chronopotentiometry data

In order to establish the mechanism and to determine the parameters of lithium transport in electrodes based on lithium-vanadium phosphate (Li₃V₂(PO₄)₃), the kinetic model was designed and experimentally tested for joint analysis of electrochemical impedance (EIS), cyclic voltammetry (CV), pulse chronoamperometry (PITT), and chronopotentiometry (GITT) data. It comprises the stages of sequential lithium-ion transfer in the surface layer and the bulk of electrode material’s particles, including accumulation of lithium in the bulk. Transfer processes at both sites are of diffusion nature and differ significantly, both by temporal (characteristic time, τ) and kinetic (diffusion coefficient, D) constants. PITT data analysis provided the following D values for the predominantly lithiated and delithiated forms of the intercalation material: 10^?9 and 3 × 10^?10 cm² s^?1, respectively, for transfer in the bulk and 10^?12 cm² s^?1 for transfer in the thin surface layer of material’s particles. D values extracted from GITT data are in consistency with those obtained from PITT: 3.5–5.8 × 10^?10 and 0.9–5 × 10^?10 cm² s^?1 (for the current and currentless mode, respectively). The D values obtained from EIS data were 5.5 × 10^?10 cm² s^?1 for lithiated (at a potential of 3.5 V) and 2.3 × 10^?9 cm² s^?1 for delithiated (at a potential 4.1 V) forms. CV evaluation gave close results: 3 × 10^?11 cm² s^?1 for anodic and 3.4 × 10^?11 cm² s^?1 for cathodic processes, respectively. The use of complex experimental measurement procedure for combined application of the EIS, PITT, and GITT methods allowed to obtain thermodynamic E,c dependence of Li₃V₂(PO₄)₃ electrode, which is not affected by polarization and heterogeneity of lithium concentration in the intercalate.     

Study of anharmonic effects in the IR spectrum of a solution of CF<Subscript>3</Subscript>Br in liquid argon

The vibrational spectrum of CF₃Br with the natural abundance ratio of isotopologues is studied in solutions in liquid Ar at T = 90 K in the frequency range 4000–400 cm^?1 with a resolution of 0.1 cm^?1 for the concentration range 3.1 × 10^?7?6.3 × 10^?3 mol %. The parameters of the vibrational spectrum of the molecule are determined: the frequencies are measured accurate to ± 0.1 cm^?1, and the transition probabilities are found up to the fourth order inclusive. One hundred fifty absorption bands of CF₃Br are interpreted, including the bands belonging to all the isotope modifications of this compound; the halfwidths of these bands are determined. For all the fundamental frequencies, the isotope shifts are obtained. Vibrational ?-resonance is studied. Using the experimental data obtained and taking into account this resonance, a complete set of parameters describing the experimental frequencies with the error δ ≈ 0.3 cm^?1 was found. This set consists of 6 harmonic frequencies and 30 anharmonicity constants, including the constants r _ik related to vibrational ?-resonances.     

Comparative study of solid-state reaction and sol-gel process for synthesis of Zr-doped Li<Subscript>0.5</Subscript>La<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript> solid electrolytes

We investigated the synergistic influences of synthesis methods (solid-state reaction vs. sol-gel process) and Zr⁴⁺ doping on the structure and ionic conductivity of perovskite-structured Li_0.5La_0.5TiO₃ (LLTO) solid electrolytes. The lithium-ion conductivity of Li_0.5La_0.5Ti_1???x Zr _x O₃ ceramic specimens was evaluated as a function of x value and compared carefully between those two synthesis methods. Regarding the conductivity, sol-gel process is better for the synthesis of LLTO than solid-state reaction. As a result, the highest grain conductivity is obtained in the sol-gel-derived pure LLTO sample with x?=?0, reaching 1.10?×?10^?3 S?·?cm^?1. Partial substitution of Zr⁴⁺ enlarges the LLTO’s grain aggregate size and increases the total superficial area of aggregates. Consequently, Zr⁴⁺ substitution not only affects the grain (bulk) conductivity, but more importantly, also improves the grain boundary conductivity and the total conductivity. The highest total conductivity is 5.84?×?10^?5 S?·?cm^?1 with x?=?0.04 by sol-gel process.