Study of the ZnO crystal growth by vapour transport methods

The crystal growth of ZnO by vapour transport is classically made with the assistance of additional species that produce a gaseous mixture, the role of which remains often uncertain in the transport and growth process. Initially, in order to study the mass transport process, a numerical simulation is made to analyse which are the requirements to have an effective transport. As the pressure of each gaseous species is generally unknown, the numerical study has been performed for different total pressures. It is found that, if congruent and equilibrium conditions are assumed at the sublimation and crystallisation interfaces, effective growth conditions can only be attained for a narrow range of total pressures. Nevertheless, it is well known that ZnO growth by vapour transport is possible for a wide range of pressures of gaseous species. As a consequence, partial pressures higher than the equilibrium ones must be present in order to justify the experimental results. We suggest that the thermal decomposition of ZnO is given by an activated process. The analysis of different mechanisms that could justify the activated decomposition, in accord with a systematic set of growth experiments, suggests that some additional species in the growth of ZnO by vapour transport promote the generation of an additional Zn pressure. This zinc pressure would act autocatalytically inducing O₂ and Zn partial pressures higher than the equilibrium ones and promoting thermal decomposition. The above-cited set of experimental growth experiences, that include the presence of C, Zn, Fe, Cu and H₂, will be analysed and interpreted according to this approach.     

Chemically assisted vapour transport for bulk ZnO crystal growth

A chemically assisted vapour phase transport (CVT) method is proposed for the growth of bulk ZnO crystals. Thermodynamic computations have confirmed the possibility of using CO as a sublimation activator for enhancing the sublimation rate of the feed material in a large range of pressures (10⁻³ to 1 atm) and temperatures (800–1200 °C). Growth runs in a specific and patented design yielded single ZnO crystals up to 46 mm in diameter and 8 mm in thickness, with growth rates up to 400 μm/h. These values are compatible with an industrial production rate. N type ZnO crystals (μ=182 cm²/(V s) and n=7 10¹⁵ cm⁻³) obtained by this CVT method (Chemical Vapour Transport) present a high level of purity (10–30 times better than hydrothermal ZnO crystals), which may be an advantage for obtaining p-type doped layers ([Li] and [Al] <10⁺¹⁵ cm⁻³). Structural (HR-XRD), defect density (EPD), electrical (Hall measurements) and optical (photoluminescence) properties are presented.     

Boron oxide encapsulated Bridgman growth of high-purity high-resistivity cadmium telluride crystals

High-purity semi-insulating CdTe crystals have been successfully grown by encapsulated (B₂O₃) Bridgman technique. The procedure strongly limits component losses allowing the achievement of stoichiometry control material and keeps a low level of impurity contamination as shown by mass spectroscopy analysis data. When strictly stoichiometry-controlled and high-purity polycrystalline source material has been used, high-resistivity crystals have been obtained without any intentional doping. EPD values in the range of 1–3×10⁴ cm⁻² have been observed in a wide region of the crystals. Luminescence spectroscopy confirms the purity and good structural quality of the material. The proposed method avoids the technical problems posed by the High Pressure Bridgman technique and fits the requirements for CdTe/CdZnTe crystals large-scale production.     

Fabrication of CdS nanorods in inverse microemulsion using HEC as a template by a convenient γ-irradiation technique

Cadmium sulfide (CdS) nanocrystals were successfully prepared in inverse microemulsion under γ-irradiation at room temperature. Their shape can be controlled by changing the surfactant concentrations and the addition of hydroxyethyl cellulose (HEC) as the template. CdS nanorods were successfully obtained under γ-irradiation using HEC as the template, which was confirmed by the observation of transmission electron microscopy (TEM). Without the addition of HEC, spherical CdS crystals were formed. X-ray powder diffraction (XRD) pattern and electron diffraction (ED) analysis showed the hexagonal lattice of CdS in the nanorods. Additionally, the optical properties of CdS nanorods were characterized by ultraviolet–visible (UV–Vis) and photoluminescence (PL) spectroscopy.     

Improvement of crystal quality in ammonothermal growth of bulk GaN

Several key improvements in crystal quality of bulk GaN grown by the ammonothermal method are presented. Full width at half maximum of (0 0 2) X-ray rocking curve was reduced to 53 and 62 arcsec for Ga-side and N-side, respectively. Transparent bulk GaN crystal was also demonstrated. Oxygen and sodium concentrations were reduced to mid-10¹⁸ and mid-10¹⁵ cm⁻³, respectively. We are currently searching for a growth condition that produces transparent bulk GaN with high structural quality and low impurities. Small-sized, semi-transparent GaN wafers were fabricated by slicing the grown bulk GaN crystals, which demonstrate the high feasibility of ammonothermal growth for production of GaN wafers.     

Compositional plane of a wide-gap semiconductor CaCdSeS lattice-matched to InP and GaAs

We have investigated compositional plane of a wide band gap solid solution semiconductor Ca_1−xCd_xSe_1−yS_y (x0.32) using powder synthesis under thermal equilibrium condition. The solubility limit at 1273 K varies with respect to the Se concentration y, taking a minimum Cd solubility limit of 0.12 at y=0.8 and a maximum limit of 0.32 at y=1.0. It is found that the system can be lattice-matched to GaAs and InP under covering the energy band gap of ultraviolet–visible region. These results allow to design optoelectronic devices adopting the Ca_1−xCd_xSe_1−yS_y system.     

Preparation and characterizations of bulk GaN crystals

The growth conditions and mechanism of hexagonal GaN platelet crystals by Li flux were studied. The experimental results confirmed that these crystals crystallized from Li–Ga–N liquid phase. Photoluminescence (PL) spectra and Raman scattering spectrum of the crystals were obtained, which show that GaN crystals obtained by this method possess good crystalline quality.     

Low temperature II–VI nanowire growth using Au–Sn catalysts

Epitaxial lateral overgrowth is reported for semi-polar (Al,Ga)N(1 1 .2) layers. The mask pattern consisted of periodic stripes of SiO₂ oriented parallel to either the GaN[1 1 .0] or the GaN[1 1 .1] direction. Lateral growth occurred either along GaN[1 1 .1] or along GaN[1 1 .0]. For growth along the [1 1 .0] direction, coalescence was achieved for layer thicknesses >4 μm. However, planarization was not observed yielding extremely corrugated surfaces. For growth in [1 1 .1] direction, coalescence was delayed by a diminishing lateral growth rate. Growth of AlGaN during ELOG resulted in coalescence. Improvement in crystal quality of such buffer layers for the growth of InGaN/GaN quantum wells was confirmed by X-ray diffraction and photoluminescence spectroscopy.     

Electrical properties and deep levels spectra of bulk SiC crystals grown by hybrid physical–chemical vapor transport method

Concentrations of nitrogen shallow donors, boron shallow acceptors, charge carriers, and electron traps were measured as a function of position along the growth axis in a series of undoped 6H–SiC boules grown by sublimation method with and without addition of hydrogen to the growth atmosphere. Elemental analysis by secondary ion mass spectrometry and measurements of electrical properties indicate that the addition of hydrogen suppresses nitrogen incorporation and formation of all electron traps. Concentration of boron is not affected by hydrogen presence. The addition of hydrogen to the growth ambient improves the uniformity of nitrogen incorporation and deep trap distribution along the growth axis. The results are interpreted as due to increased carbon transport and corresponding shift of crystal stoichiometry toward carbon-rich side of the SiC existence range.     

Solvothermal growth of ZnO

The growth of ZnO single crystals and crystalline films by solvothermal techniques is reviewed. Largest ZnO crystals of 3 inch in diameter are grown by a high-pressure medium-temperature hydrothermal process employing alkaline-metal mineralizer for solubility enhancement. Structural, thermal, optical and electrical properties, impurities and annealing effects as well as machining are discussed. Poly- and single-crystalline ZnO films are fabricated from aqueous and non-aqueous solutions on a variety of substrates like glass, (100) silicon, -Al₂O₃, Mg₂AlO₄, ScAlMgO₄, ZnO and even some plastics at temperatures as low as 50 °C and ambient air conditions. Film thickness from a few nanometers up to some tens of micrometers is achieved. Lateral epitaxial overgrowth of thick ZnO films on Mg₂AlO₄ from aqueous solution at 90 °C was recently developed. The best crystallinity with a full-width half-maximum from the (0002) reflection of 26 arcsec has been obtained by liquid phase epitaxy employing alkaline-metal chlorides as solvent. Doping behavior (Cu, Ga, In, Ge) and the formation of solid solutions with MgO and CdO are reported. Photoluminescence and radioluminescence are discussed.     

Investigation of the role of cadmium sulfide in the surface passivation of lead sulfide quantum dots

Surface passivation of PbS nanocrystals (NC), resulting in strong photoluminescence, can be achieved by the introduction of CdS precursors. The role of CdS in the surface passivation of PbS NCs is uncertain, as the crystalline structure of CdS and PbS are different, which should impede effective epitaxial overgrowth. Absorption spectroscopy is used to show that the CdS precursors strongly interact with the PbS NC surface. Electron microscopy reveals that the introduction of CdS precursors results in an increased particle size, consistent with overcoating. However, we also find the process to be highly non-uniform. Nevertheless, evidence for epitaxial growth is found, suggesting that effective surface passivation may be possible.     

ZnO hexagonal prisms grown onto p-Si (1 1 1) substrate from poly (vinylpyrrolidone) assisted electrochemical assembly

Nonionic polymer poly (vinylpyrrolidone) (PVP) was firstly mixed into oxygenated zinc chloride electrolyte to modulate the crystal growth and morphology of ZnO from electrodeposition. Arrays of ZnO hexagonal prisms with well-defined (0 0 0 1) end facets and side facets were grown perpendicularly onto p-type Si substrates using the simple and economic route. It was observed that the concentration of PVP played an important role in the final morphology and size of ZnO crystals. The optical studies indicated that the addition of PVT not only influenced crystal growth habit but also improved the optical properties of ZnO.     

A greener synthetic route to monodisperse CdSe quantum dots with zinc-blende structure

A much cheaper and greener route to monodisperse CdSe quantum dots (QDs) with zinc-blende structure has been developed. The N,N-dimethyl-oleoyl amide was chosen as the solvent, eliminating the needs of air-sensitive and toxic trioctylphosphine (TOP) or tributylphosphine (TBP), and cadmium oxide and elemental selenium as sources. The as-prepared CdSe QDs show an apparent blue-shift in the ultraviolet and visible (UV–vis) absorption peaks. The emission peak of the QDs can be tuned by changing synthesis time only.     

Influence of growth conditions on microstructure and properties of GaSe crystals

GaSe crystals have been grown from melt. There are several reasons why it is difficult to meet ideal demands for nonlinear optic material, GaSe single crystal. First, these crystals have a tendency towards lamination because of great difference in a and c crystal lattice parameters and very weak Vander der Waals forces in c direction. Next, there is a great difference in saturation vapor pressure of the components, which can cause nonstoichiometry of a melt-grown crystal composition. Another obstacle in the growth of perfect GaSe crystals is dendrite formation caused by instability of the growth front. To overcome this obstacle we used Bridgman technique and have found the temperature and pressure conditions, and growth velocity which provide growth of perfect bulk single crystals of about 100 mm in length and 20 mm in diameter. Sharp Laue patterns and a rocking curve confirm perfect structure of the grown crystals. Electron-probe X-ray microanalysis shows stoichiometric composition of GaSe crystals and X-ray phase analysis reveals presence of single-phased hexagonal structure.     

Epitaxial growth of ZnO thin films on Si substrates by PLD technique

Epitaxial ZnO thin films have been grown on Si(1 1 1) substrates at temperatures between 550 and 700 °C with an oxygen pressure of 60 Pa by pulsed laser deposition (PLD). A ZnO thin film deposited at 500 °C in no-oxygen ambient was used as a buffer layer for the ZnO growth. In situ reflection high-energy electron diffraction (RHEED) observations show that ZnO thin films directly deposited on Si are of a polycrystalline structure, and the crystallinity is deteriorated with an increase of substrate temperature as reflected by the evolution of RHEED patterns from the mixture of spots and rings to single rings. In contrast, the ZnO films grown on a homo-buffer layer exhibit aligned spotty patterns indicating an epitaxial growth. Among the ZnO thin films with a buffer layer, the film grown at 650 °C shows the best structural quality and the strongest ultraviolet (UV) emission with a full-width at half-maximum (FWHM) of 86 meV. It is found that the ZnO film with a buffer layer has better crystallinity than the film without the buffer layer at the same substrate temperature, while the film without the buffer layer shows a more intense UV emission. Possible reasons and preventive methods are suggested to obtain highly optical quality films.     

Charge transfer in CdTe at 200 and 300 K

Using a perfect single crystal sample of CdTe grown using PVT method, the electronic charge transfer in the II–VI compound semiconductor CdTe at 200 and 300 K has been evaluated using two different approaches: (1) by solving a quadratic equation involving the observed structure factors of h+k+l=4n+2 type reflections; and (2) by a graphical approach in which the observed and calculated atomic form factors are extrapolated to sinθ/λ=0, to determine the transferred charge. Precise X-ray structure factors collected using MoK radiation have been used for the analysis. The results obtained are reasonable and clearly indicate the ionicity by which charge is transferred from Cd to Te in CdTe.     

Large-size β-Ga2O3 single crystals and wafers

Large-size single crystals of β-Ga₂O₃ with 1 inc in diameter have been grown by the floating zone technique. The stable growth conditions have been determined by the examination of the crystal structure. Wafers have been cut and fine polished in the (1 0 0), (0 1 0) and (0 0 1) planes. These were highly transparent in the visible and near UV, as well as electrically conductive, indicating the potential use of β-Ga₂O₃ as a substrate for optoelectic devices operating in the visible/near UV and with vertical current flow.     

Growth and energy band gap of CaSeS thin films prepared by hot-wall epitaxy

This paper investigates preparation of CaSeS thin films using hot-wall epitaxy. These films can be grown epitaxially on cleaved BaF₂(1 1 1) at a substrate temperature of 873 K by tailoring the VI/II flux ratio vaporized from Ca and SeS resources. The optical absorption edge of these films thus tailored can be observed clearly, shifting toward higher photon energy with increasing S content. In particular, the energy band gap of CaSe_0.66S_0.34, capable of lattice-matching to InP was found to be 4.69 eV, producing considerably large band gap difference of 3.34 eV between the CaSe_0.66S_0.34 and InP.     

Oriented growth of benzophenone crystals from undercooled melts

The tin sulfides compounds SnS and SnS₂ nanoflakes were prepared by the microwave-assisted polyol synthetic method. The as-prepared nanoscale flakes were characterized by X-ray powder diffraction, transmission electron microscopy, selected area electron diffraction, X-ray photoelectron spectroscopy and Raman spectra. The influences of solvents and microwave irradiation on the formation of products have been studied.     

Optical and electrical properties of Be doped GaN bulk crystals

Highly resistive GaN : Be was obtained by means of synthesis of Ga+Be with atomic nitrogen under high nitrogen pressure. Activation energy of resistivity is about 1.5 eV. This material exhibits features very different from those observed in highly resistive bulk GaN : Mg. Up to 300 K strong yellow band dominates photoluminescence spectrum in resistive GaN : Be crystals. Positron annihilation studies point to the presence of gallium vacancies, V_Ga. In highly resistive GaN:Mg neither yellow band with considerable intensity, nor detectable concentration of V_Ga was found. We also discuss the puzzling findings in highly resistive bulk GaN : Be of morphological features typical for highly conducting bulk n-GaN material.