Gemini表面活性剂对疏水缔合聚丙烯酰胺界面吸附膜扩张流变性质的影响

采用小幅低频振荡和界面张力弛豫技术, 考察了疏水缔合水溶性聚丙烯酰胺(HMPAM)在正癸烷-水界面上的扩张黏弹性质, 研究了不对称Gemini表面活性剂C₁₂COONa-p-C₉SO₃Na对其界面扩张性质的影响. 研究发现, 疏水链段的存在, 使HMPAM在界面层中具有较快的弛豫过程, 扩张弹性显示出明显的频率依赖性. 表面活性剂分子可以通过疏水相互作用与聚合物的疏水嵌段在界面上形成类似于混合胶束的特殊聚集体. 表面活性剂分子与界面聚集体之间存在快速交换过程, 可以大大降低聚合物的扩张弹性. 同时, 聚合物分子链能够削弱表面活性剂分子长烷基链之间的强相互作用, 导致混合吸附膜的扩张弹性远低于单独表面活性剂吸附膜.     

A polyacrylate prepared using polyurethane surfactants: properties of emulsion and film

The designed polyurethane surfactant (PUS) was used as a macromolecular surfactant for the preparation of polyacrylate emulsion without any other surfactants and stabilizers. The resultant polymer emulsion and film properties were compared with those of the emulsion prepared with sodium dodecyl sulfate (SDS). Long shelf-life of the polymer emulsion can be achieved at proper composition. Polymer particles show core-shell and nano-scale structure with narrow distribution. Thermoanalysis results show phase separation in the polymer film, which leads to gloss decrease with the PUS content increase. Such polymer films show good water resistance and mechanical strength.     

Adsorbed surfactants as templates for the synthesis of morphologically controlled polyaniline and polypyrrole nanostructures on flat surfaces: from spheres to wires to flat films

Nanostructures of polyaniline (PAni) and polypyrrole (PPy) with controlled morphologies have been synthesized on atomically flat surfaces using adsorbed surfactant molecules as templates. Atomic force microscopy (AFM) has been used to investigate polymer film formation on highly oriented pyrolytic graphite (HOPG) and chemically modified HOPG. Morphological control over the resulting polymer film is possible by the addition of coadsorbing molecules, manipulation of the length of the surfactant hydrophobe, or by changing the surface chemistry of the adsorbing substrate. Phase transitions between spheres, cylinders/wires, and featureless films have been observed which exactly parallel transitions between spheres, cylinders, and flat layers in the adsorbed surfactant. Parallel arrays of PAni nanowires can be synthesized with alignment evident over large areas in a simple self-assembly technique in which fabrication and arrangement take place simultaneously. Such a technique in which one can engineer sub-100-nm-ordered nanoscale pi-conjugated polymer structures of a desired shape by a simple self-assembly process presents potential as templates, sensors, and microelectronic devices.     

Film Formation and Redispersion of Waterborne Latex Coatings

Poly(vinyl acetate-co-ethylene) latex dispersions are prepared and their films investigated with a focus on the effect of composition upon redispersion. Films of dispersions containing sufficient amounts of poly(vinyl alcohol) (PVA) can be redispersed in water. This property is lost in the presence of surfactant, a fact which suggests a procedure to control film formation. It is demonstrated that redispersion is due to a PVA-membrane which separates the particles. Loss of redispersibility in the presence of surfactant proceeds with the breakup of the membranes and a corresponding change of film properties. Experimental data is provided by light microscopy, mechanical testing, and TEM in conjunction with a staining method new to the field. The hypothesis is developed that interaction with surfactant leads to imperfect PVA-membranes that are no longer able to prevent latex polymer interdiffusion. Fluorescence correlation spectroscopy demonstrates the formation of surfactant micelles, as well as the simultaneous adsorption and aggregation of PVA onto the micelles. It is concluded that the competing surface of the surfactant micelles traps enough PVA to cause thinning and fragmentation of the membranes surrounding the particles, which enables interdiffusion of latex polymer. This effect can be used to convert the system from one forming a redispersible coating to one forming a nonredispersible (permanent) film. Copyright 2000 Academic Press.     

三元复合驱碱/表面活性剂/聚合物模拟原油乳状液稳定动力学特性

基于两相分离的乳状液稳定模型,研究了三元复合驱模拟原油乳状液稳定动力学特性;通过液膜强度和油水界面张力探讨了碱/表面活性剂/聚合物对模拟原油乳状液稳定动力学特性的影响机理。 结果表明,乳状液稳定模型可以很好的评价乳状液的稳定性,并得到乳状液的稳定动力学特性;碱浓度小于900 mg/L有利于乳状液的稳定,碱浓度大于900 mg/L不利于乳状液的稳定;表面活性剂和聚合物浓度的增加使得形成的模拟原油乳状液更加稳定;模拟原油乳状液的稳定作用主要是通过碱、表面活性剂降低油水界面张力并增加油水界面膜强度,聚合物通过提高界面膜强度实现的,三者存在协同效应。     

Use of surfactants to remove water-based inks from plastic film: effect of calcium ion concentration and length of surfactant hydrophobe

Effective plastic film deinking could permit the reuse of recycled polymer to produce clear film, reduce solid waste for landfills, reduce raw material demand for polymer production, and aid process economics. In this study, the deinking of a commercial polyethylene film printed with water-based ink was studied using surfactants in the presence of hardness ions (calcium ions) at various pH levels. The electrostatic properties of ink particles in a washing bath were also investigated. Synthetic anionic surfactant or fatty acid soap in the presence of calcium ions at alkaline pH levels was found to be nearly as effective at deinking as cationic, nonionic, or amphoteric surfactants alone. However, adding calcium ions decreases the deinking effectiveness of cationic, nonionic, and amphoteric surfactants. Increasing the length of the ionic surfactant hydrophobe enhances deinking. Zeta potential measurements showed that water-based ink particles in water reach the point of zero charge (PZC) at a pH of about 3.6, above which ink particles are negatively charged, so cationic surfactant tends to adsorb better on the ink than anionic surfactant above the PZC in the absence of calcium. As the cationic surfactant concentration is varied between 0.005 and 25 mM, the zeta potential of the ink particles reverses from negative to positive owing to adsorption of cationic surfactant. For anionic surfactants, added calcium probably forms a bridge between the negatively charged ink and the negatively charged surfactant head groups, which synergizes adsorption of the surfactant and aids deinking. In contrast, calcium competes for adsorption sites with cationic and nonionic surfactants, which inhibits deinking. All the surfactants studied here disperse ink particles effectively in the washing bath above pH 3 except for the ethoxylated amine surfactant.     

The influence of sodium ethene sulphonate comonomer on the film formation process of poly(vinyl acetate) dispersions

Various latex dispersions from vinyl acetate/sodium ethene sulphonate (sodium vinyl sulphonate) copolymers, stabilised by a constant amount of Hostapal BV, a surfactant with poly(ethylene oxide) groups, were investigated by a variety of solid and liquid state nuclear magnetic resonance methods. In order to investigate the influence of sodium ethene sulphonate on the film formation process, the serum and polymer were analysed separately. The stoichiometric monomer composition of the copolymer in the aqueous phase and in the hydrophobic particles was obtained. The ionic comonomer is enriched at the particle surface via its proximity to the applied surfactant by two-dimensional exchange NMR. For investigations of the film formation process, latex dispersions were prepared and dried to form spatially homogeneous films at different defined solid contents. Depending on the chemical composition of a chosen dispersion, NMR allows the investigation of the drying process of the water. The drying process is a function of the ionic strength of the dispersion and the hydrophilicity of the polymer. It is correlated to the drying mechanism of the water within the film. A not fully dried film contains external water outside the particles, water at ionic and non-ionic groups at surfactants in the polymer water interface and, additionally, water in the swollen and mobilised polymer. The distribution of water to these environments is markedly changed by the ionic comonomer, especially close to the end of the drying process.     

Carboxymethyl chitin as a matrix for composites with iron nanoparticles

The stabilizing effect of a biodegradable polymer in a macromolecular system based on 6-O-carboxymethyl chitin polyelectrolyte and iron nanoparticles is studied. Stabilization is associated with hydrogen bonding between the functional groups of the polymer and a surfactant forming the shell of a metal nanoparticle micelle. Composite film materials containing iron nanoparticles 2–4 nm in size are obtained.     

阳离子可聚合表面活性剂的研究进展

可聚合表面活性剂含有可聚合基团,以牢固的共价键键合到聚合物粒子上,成为聚合物的一部分,有效避免了表面活性剂的解吸及其在乳胶膜中的迁移,减少了乳胶膜表面的亲水基团,可以克服传统表面活性剂的许多弊端。阳离子可聚合表面活性剂主要为季铵盐,其容易吸附于一般固体表面,其水溶液一般有优异的杀菌性。本文综述阳离子可聚合表面活性剂,根据不同方式对其进行分类,分别介绍聚合基团不同的阳离子可聚合表面活性剂的合成和应用现状,并对其应用前景作了展望。     

On the Origin of Foam Stability: Understanding from Viscoelasticity of Foaming Solutions and Liquid Films

The foam stability (drainage half-life) of α-olefin sulfonate (AOS) with partially hydrolyzed polyacrylamide (HPAM) or xanthan gum (XG) solution was evaluated by the Warring Blender method. With the increase of polymer (HPAM or XG) concentration, foam stability of the surfactant–polymer complexes increased, and the drainage half-life of AOS-XG foam was higher than that of AOS-HPAM foam at the same polymer and surfactant concentration. With the addition of polymer (HPAM or XG), the viscoelasticity of bulk solution and the liquid film were enhanced. The viscoelasticity of AOS-XG bulk solution and liquid film were both higher than that of AOS-HPAM counterparts.      

Characterizing the distribution of nonylphenol ethoxylate surfactants in water-based pressure-sensitive adhesive films using atomic-force and confocal Raman microscopy

Surfactant distributions in model pressure-sensitive adhesive (PSA) films were investigated using atomic force microscopy (AFM) and confocal Raman microscopy (CRM). The PSAs are water-based acrylics synthesized with n-butyl acrylate, vinyl acetate, and methacrylic acid and two commercially available surfactants, disodium (nonylphenoxypolyethoxy)ethyl sulfosuccinate (anionic) and nonylphenoxypoly(ethyleneoxy) ethanol (nonionic). The ratio of these surfactants was varied, while the total surfactant content was held constant. AFM images demonstrate the tendency of anionic surfactant to accumulate at the film surfaces and retard latex particle coalescence. CRM, which was introduced here as a means of providing quantitative depth profiling of surfactant concentration in latex adhesive films, confirms that the anionic surfactant tends to migrate to the film interfaces. This is consistent with its greater water solubility, which causes it to be transported by convective flow during the film coalescence process. The behavior of the nonionic surfactant is consistent with its greater compatibility with the polymer, showing little enrichment at film interfaces and little lateral variability in concentration measurements made via CRM. Surfactant distributions near film interfaces determined via CRM are well fit by an exponential decay model, in which concentrations drop from their highs at interfaces to plateau values in the film bulk. It was observed that decay constants are larger at the film-air interface compared with those obtained at the film-substrate side indicating differences in the mechanism involved. In general, it is shown here that CRM acts as a powerful compliment to AFM in characterizing the distribution of surfactant species in PSA film formation.     

Interfacial Dilational Properties of Hydrophobically Modified Partly Hydrolyzed Polyacrylamide and Anionic Surfactants at the Water-Decane Interface

The dilational viscoelastic properties of hydrophobically modified partly hydrolyzed polyacrylamide and anionic surfactants (4,5-diheptyl-2-propylbenzene sulfonate and gemini surfactant C₁₂COONa-p-C₉SO₃Na) in the absence or presence of electrolyte have been investigated at the decane–water interface by means of longitudinal method and the interfacial tension relaxation method. Experimental results show that at low surfactant concentration, the increase of the dilational modulus by the addition of surfactant molecules at low frequency might be explained by the mix-adsorption of the polymer chains and surfactant molecules. At the same time, polymer chain could sharply decrease the dilational modulus of surfactant film mainly due to the weakening of the strong interactions among long alkyl chains in surfactant molecules. At high surfactant concentration, the addition of surfactant molecules can decrease the dilational modulus of polymer solution due to the fast process involving in the exchange of surfactant molecules between the interface and the mixed complex formed by surfactant molecules and hydrophobic micro-domains. The added electrolyte, which results in screening of electrostatic interactions between the ionized groups, generally increases the frequency dependence of the interfacial dilational modulus. The data obtained on the relaxation processes via interfacial tension relaxation measurements can explain the results from oscillating barriers measurements very well.     

表面活性剂对驱油聚合物界面剪切流变性质的影响

利用双锥法研究了表面活性剂十二烷基苯磺酸钠(SDBS)和十六烷基三甲基溴化铵(CTAB)对油田现场用部分水解聚丙烯酰胺(PHPAM)和疏水改性聚丙烯酰胺(HMPAM)溶液的界面剪切流变性质的影响,实验结果表明:HMPAM分子通过疏水作用形成界面网络结构,界面剪切复合模量明显高于PHPAM.SDBS和CTAB通过疏水相互作用与HMPAM分子中的疏水嵌段形成聚集体,破坏界面网络结构,剪切模量随表面活性剂浓度增大明显降低.同时,界面膜从粘性膜向弹性膜转变.低SDBS浓度时,少量SDBS分子与PHPAM形成混合吸附膜,界面膜强度略有升高;SDBS浓度较高时,界面层中PHPAM分子被顶替,吸附膜强度开始减弱.阳离子表面活性剂CTAB通过静电相互作用中和PHPAM分子的负电性,造成聚合物链的部分卷曲,从而降低界面膜强度.弛豫实验结果证实了表面活性剂破坏HMPAM网络结构的机理.     

Influence of Nafion Coatings and Surfactant on the Stripping Voltammetry of Heavy Metals at Bismuth‐Film Modified Carbon Film Electrodes

Nafion polymer coated bismuth‐film‐modified carbon film electrodes have been investigated for reducing the influence of contaminants such as surfactants in the anodic stripping voltammetry of trace metal ions. The influence of the coating on electrode response has been tested with both ex situ and in situ bismuth film deposition, with and without the polymer coating. The electrode assemblies and interfacial characteristics in the presence of the non‐ionic surfactant Triton‐X‐100 have been probed with electrochemical impedance spectroscopy. The Nafion coating successfully decreases the adsorption of Triton on the bismuth film surface, and demonstrates that this strategy allows measurement of these trace metals in environmental samples containing surfactants.     

Response mechanism of novel polyaniline composite conductimetric pH sensors and the effects of polymer binder, surfactant and film thickness on sensor sensitivity

This paper reports on investigations into the response mechanism of novel polyaniline composition conductimetric pH sensors and the effects of polymer binder, surfactant and film thickness on this response. It was revealed through X-ray photoelectron spectroscopy, focussed ion beam milling and impedance spectroscopy that the response mechanism was due to the deprotonation of the polymer backbone nitrogen atoms located on the uppermost surface level of the functional material particles. The equivalent circuits for the sensing layer were modelled using the Cole-Cole model for a range of pH environments. The optimum sensing layer composition was determined to contain less than 50 wt.% polymer binder with 5 wt.% surfactant. This composition was determined by examining the effects of both binder and surfactant on the electrical characteristics and sensor response of the composite films. The thickness of the sensing layer was found to have no discernable response on the sensing characteristics of the conductimetric pH sensors.     

可聚合表面活性剂的研究进展

在乳液聚合中，表面活性剂发挥着非常关键的作用，但同时它们也存在不足的方面，一个比较有前景的方法就是使用可聚合表面活性剂。可聚合表面活性剂以牢固的共价键键合到聚合物粒子上，有效避免了表面活性剂的解析及其在膜中的迁移。本文综述了近年来可聚合表面活性剂的进展，主要讨论了阴离子、非离子、阳离子可聚合表面活性剂的特征和性质及其在乳液聚合中的应用。     

Soluble organic additive effects on stress development during drying of calcium carbonate suspensions

The effect of polymer, plasticizer, and surfactant additives on stress development during drying of calcium carbonate particulate coatings was studied using a controlled-environment apparatus that simultaneously monitors drying stress, weight loss, and relative humidity. We found that the calcium carbonate coatings display a drying stress evolution typical of granular films, which is characterized by a sharp capillary-induced stress rise followed by a rapid stress relaxation. The addition of a soluble polymer to the CaCO3 suspension resulted in a two-stage stress evolution process. The initial stress rise stems from capillary-pressure-induced stresses within the film, while the second, larger stress rise occurs due to solidification and shrinkage of the polymeric species. Measurements on the corresponding pure polymer solutions established a clear correlation between the magnitude of residual stress in both the polymer and CaCO3-polymer films to the physical properties of the polymer phase, i.e. its glass transition temperature, T(g), and Young's modulus. The addition of small organic molecules can reduce the residual stress observed in the CaCO3-polymer films; e.g., glycerol, which acts as a plasticizer, reduces the drying stress by lowering T(g), while surfactant additions reduce the surface tension of the liquid phase, and, hence, the magnitude of the capillary pressure within the film.     

Effects of Polymer Binder,Surfactant and film Thickness on pH Sensitivity of Polymer Thick Film Sensors

Measuring the change of the conductivity of a Polyaniline (PANI) film while in contact with a solution is considered to be a costeffective tool for pH sensing. The device consists of a PANI film deposited between two identical electrodes, reducing the number of fabrication steps. To ensure the sensors display an optimum response to solutions of different pH values, it is important to understand the effect of the polymer binder, surfactant and film thickness. The effect of varying the amount of Polyvinyl butyral (PVB) and Hypermer (PS3) on the pH sensitivity of screen printed thick film sensors is reported.     

Surfactant exudation in the presence of a coalescing aid in latex films studied by atomic force microscopy1

We report atomic force microscopy images of surfactant (SDS) exudation in PBMA latex films, in the presence and the absence of a coalescing aid (Texanol^?, TPM). The exudates appear as hilly islets, and at times as mountains, at the film surface. Their size and number increase upon annealing above the glass-transition temperature of the latex polymer. TPM was found to be a strong promoter of surfactant exudation at the air-polymer interface. In the absence of TPM, annealing the films for several hours at 70°C led to very little migration of surfactant to the surface at most sites in the film. When the films with structures of SDS on their surface were immersed in water, these structures disappeared. Pores, ranging in size from tens to hundreds of nm in diameter, were clearly visible in the surface of the films. These films dry from the edges of the film inward, with a propagation front concentrating the water-soluble species into a turbid, moist region in the center. At this site, the rate at which the surfactant comes to the surface is enormously enhanced over that at other sites in the film. This is likely due to the high concentration of surfactant in this region, transported there by the drying process. © 1995 John Wiley & Sons, Inc.     

Preparation of Covalently‐colored Polymer Latex via Batch Emulsion Polymerization

Covalently‐colored polymer latex was synthesized via batch emulsion copolymerization of styrene, butyl acrylate and methacrylic acid in the presence of red polymerizable dye monomer consisting of anthraquinone chromophore, alkyl spacer and acryloyl group, and the influences of the initiator, surfactant and polymerizable dye on the polymerization and the latex properties were investigated. Results showed that the initiator amount was a determinative factor for the monomer conversion, and a high conversion of the polymerizable dye could be achieved when the ammonium persulfate amount was equal to or more than 1 wt% to the total monomers. Most of the chromophores were covalently bonded to the polymer chains if the polymerizable dye was used in the range of 0–1.5 wt%. The light fastness of the resulting latex film was much better than that of the noncovalently‐colored polymer film.