磷酸钡钙∶铈、锰红色荧光粉的研制

采用高温固相反应合成了磷酸钡钙∶铈、锰红色荧光粉。借助TG,XRD,荧光粉相对亮度仪、荧光分光光度仪等手段系统研究了合成过程中原料化学组成及配比、合成条件对磷酸钡钙∶铈、锰发光性能的影响。结果表明,荧光粉基质(BaxCa1-x)3(PO4)2具有畸变的Ca3(PO4)2结构。该荧光粉中Ce3+是助激活剂,Mn2+是激活剂,由Ce3+→Mn2+的能量传递使Mn2+激发产生650 nm左右的发射,当Ce3+和Mn2+浓度相等且都为0.15时,荧光粉有最高的红色发射亮度。     

共沉淀法合成的（Y，Gd）BxV1-xO4-x：Eu荧光粉的光谱特性研究

采用共沉淀反应软化学法合成了体色洁白的（Y，Gd）BxV1-xO4-x：Eu^3＋荧光粉。在147nm真空紫外线的激发下，（Y，Gd）BxV1-xO4-x：Eu^3＋荧光粉的发射主峰位于619nm，红色色纯度优于PDP用商品（Y，Gd）BxV1-xO4-x：Eu^3＋荧光粉，但其相对发光亮度只有商品粉的90％，是一种有前途的PDP用和荧光灯用的红色荧光粉。     

YAG：Ce^3＋荧光粉的合成及α-Al2O3籽晶对相形成的促进作用

用聚丙烯酰胺凝胶法来合成YAG：Ge^3＋荧光粉，用XRD对煅烧过程粉体的结构进行了跟踪测定。结果发现，当直接煅烧凝胶时，可观察到θ-Al2O3，YAM和YAP等中间相的形成，而当煅烧含有α-Al2O3，YAM和YAP的形成，加速其与Y203的反应而在较低温度下直接生成YAG相。合成YAG：Ce^3＋荧光粉的发射峰为处于550nm的宽峰，其激发光谱有两个主要的吸收峰，主峰位于460nm，可以与GaN LED的蓝色发射相匹配而用于白光LED的组装。一些助熔剂可以提高荧光粉的光致发光特性，这归因于助熔剂对YAG结晶过程的改进作用和对YAG：Ce^3＋中三价铈离子的稳定作用。     

一类新的红色荧光粉MYzS4：Er^3＋（M=Srz＋，Ba^2＋）的合成与表征

Eu^2＋激活的CaS：Eu^[1],Eu^3＋和Sm^3＋激活的硫氧化物^[2]，Pr^3＋激活的Ca0.8Zn0.2Ti03^[3]以及Eu^2＋和Mn^2＋掺杂的SrY2S4^[4]都是重要的红色发光材料。然而，这些红色荧光粉的发射峰波长都短于650nm，对于农用日光转换材料^[5]，红色发射峰波长达到660nm才能与叶绿素的红区吸收相吻合。     

掺三价铈离子四偏磷酸盐NaLn(PO3)4 (Ln=La, Gd)的真空紫外光谱研究

用高温固相法合成了NaLn（PO3）4：1．0％（原子分数）Ce^3＋（Ln=La,Gd）两种粉末发光材料,在合肥国家同步辐射实验室（NSRL）测得两种样品中Ce^3＋的真空紫外光谱。根据真空紫外光谱图,得到了两种稀土偏磷酸盐中所掺Ce^3＋离子5d轨道的能级分裂图。结合NaLa（PO3）4和NaGd（PO3）4的单晶结构数据,发现随着Ln-O平均键长的减小,Ce^3＋离子5d轨道的晶场劈裂（εcfs）、重心位移（εc）和总的红移（total redshilt,D）均增大。根据配体极化模型,计算了两种化合物中掺杂Ce^3＋离子的有效平均键长（Reff）和光谱极化率（αsp）,发现随着平均键长Rav（Ln—O）变短,Ce^3＋离子的光谱极化率（αsp）也随之减小。     

KMgF3∶Ce^3＋,Eu^2＋的溶剂热合成与光谱性质

采用溶剂热法合成了Eu^2＋,Ce^3＋单掺和双掺KMgF3。分析了样品的结构与形貌。结果表明,所合成的样品均为单相,颗粒粒度分布集中。测定了它们的激发和发射光谱,结果显示：在单掺Eu^2＋的KMgF3中,没有观察到位于420nm附近由微量氧色心引起的宽带发射,只发现峰值位于360nm附近的锐峰线发射,说明溶剂热合成的KMgF3∶Eu中氧含量极低;在KMgF3双掺体系中由于Eu^2＋和Ce^3＋竞争吸收激发能,Eu^2＋把能量传递给Ce^3＋,存在Eu^2＋→Ce^3＋能量传递过程,观察到Ce^3＋的较强的发射带和Eu^2＋的较弱的线发射,并讨论了能量传递机理。     

Sr1-xZnxY2S4∶Er^3＋,Eu^2＋荧光粉的合成与发光特性的研究

采用碳酸盐前躯体高温分解法合成了Sr1-xZnxY2S4∶Er^3＋,Sr1-xZnxY2S4∶Eu^2＋和Sr1-xZnxY2S4∶Er^3＋,Eu^2＋红色荧光粉。XRD图谱表明,Zn^2＋掺杂量x〈0.2 mol时,粉末样品为CaFe2O4型正交晶体。Zn^2＋离子在Sr1-xZnxY2S4∶Er^3＋,Eu^2＋中的固溶量（xmol）对荧光粉的发射强度影响很大。随着Zn^2＋离子掺杂浓度的增加,Sr1-xZnxY2S4∶Er^3＋,Eu^2＋（SZYSEE）紫外区激发峰（200-413 nm）发生红移,并与可见光激发带（413-600 nm）形成一个连续的宽带谱,与紫外和GaN基LED芯片辐射都有良好的匹配性。当Zn^2＋掺杂量为0.1 mol时,SZYSEE的发光强度达到最大,其发光强度比未掺Zn2＋的增强10.7倍。Sr0.9Zn0.1Y1.76S4∶0.24Er^3＋,0.006Eu^2＋是一种潜在的白光LED用红色荧光粉。     

Sr5(PO4)3Cl:Eu2+蓝色荧光粉合成新方法的研究

Sr5 (PO4)3Cl:Eu2+是一种重要的蓝色发射荧光材料,通常采用高温固相反应法来制备.本文利用Sr5(PO4)3(OH)与Sr5(PO4)3Cl结构相同的特点,采用沉淀法合成出羟基磷酸锶铕前体,经过氯化铵和助熔剂作用下的固相氯代反应合成出Sr5(PO4)3Cl:Eu2+荧光粉.考察了pH值与原料比例等对沉淀反应过程及产物的影响,并讨论了氯化铵作用下的氯代过程以及助熔剂对产物荧光粉形貌的作用机制.研究结果表明,本合成方法条件易控,且合成产物Sr5 (PO4)3Cl:Eu2+的物相纯度高,尺寸分布均匀,形貌规则,发光性能优良.     

尿素辅助的共沉淀模板法制备LSO：Ce^3＋发光粉体

采用尿素辅助的共沉淀模板法，通过在单分散的SiO2微球模板上包覆Lu（OH），制备出了具有核-壳结构的Si02@Lu（OH）3粉体颗粒，经煅烧后得到了LSO：Ce^3＋荧光粉体．结果发现煅烧温度对荧光粉的相组成和形貌都产生了很大影响．当在1200℃下煅烧2h时，得到了单相LSO：Ce^3＋粉体．在900℃煅烧后的粉体颗...     

偏硼酸钆镁:铈(Ⅲ)、铽(Ⅲ)、锰(Ⅱ)高显色性荧光粉的研制

用高温固相反应法合成了高显色性橙红粉(Gd，Ce，Tb)(Mg，Mn)B5O10，研究了硼酸用量、Tb／Ce比例、氢气浓度和灼烧温度等对合成产物发光性能的影响。实验表明，当硼酸过量8％、Tb／Ce≥2．5、氢气浓度≤10％、灼烧温度≥1000℃时，可制得发光亮度较高的高显色性橙红色荧光粉。为进一步探讨Tb，Mn的激活机制，制备了高显色性绿粉(Gd，Ce，Tb)MgB5O10和高显色性红粉(Gd，Ce)(Mg，Mn)B5O10作对比。研究表明，通过无辐射能量机制，Ce^3 能够有效地将吸收的紫外能量传递给Tb^3 ，Gd^3 作为能量传递过程中的中间体，其作用是增强Tb^3 的发光，即发生了“激发→Ce^3 →(Gd^3 )n→Tb^3 →发射”过程。此外，Mn^2 发光不能被Ce^3 直接敏化，也是通过Gd^3 作为中间体，发生Gd^3 →Mn^2 的能量传递。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.