Determination of pore sizes and volumes of porous materials by 129Xe NMR of xenon gas dissolved in a medium

In our previous paper (J. Phys. Chem. B 2005, 109, 757) it was illustrated that the 129Xe NMR spectra of xenon dissolved in acetonitrile confined into mesoporous materials give detailed information on the system, especially about the pore sizes. A resonance signal originating from xenon atoms sited in very small cavities built up inside the pores during the freezing transition (referred to as signal D) turned out to be highly sensitive to the pore size. The emergence of this signal reveals the phase transition temperature of acetonitrile inside the pores, which can also be used to determine the size of the pores. In addition, the difference in the chemical shifts of two other signals arising from xenon dissolved in bulk and confined acetonitrile (B and C) provides another method for determining the pore sizes. In the present work, the observed correlations have been investigated using an extensive set of measurements with a variety of porous materials (silica gels and controlled pore glasses) with the mean pore diameters ranging from 43 to 2917 A. The usefulness of the correlations has been demonstrated by calculating the pore size distributions from the spectral data. The distributions are in agreement with those reported by the manufacturers, when the mean pore diameter is smaller than approximately 500 A. In addition, it has been shown that the porosity of the materials can be determined by comparing the intensities of the signals arising from the bulk and confined liquid. When acetonitrile is replaced by cyclohexane in the sample, the dependence of the chemical shift difference between the B and C signals on the pore size becomes more sensitive, but no D signal appears below the freezing point. In addition, the influence of xenon gas on the melting points of bulk and confined acetonitrile has been studied by 1H NMR cryoporometry. The measurements show that the temperature of the latter transition lowers slightly more, and consequently affects the pore sizes calculated by means of the difference in the phase transition temperatures. Hysteresis in the phase transitions in a cooling-warming cycle has also been studied as a function of the temperature stabilization time by 129Xe NMR of xenon dissolved in acetonitrile.     

A double quantum (129)Xe NMR experiment for probing xenon in multiply-occupied cavities of solid-state inclusion compounds

A method is presented for detecting multiple xenon atoms in cavities of solid-state inclusion compounds using (129)Xe double quantum NMR spectroscopy. Double quantum filtered (129)Xe NMR spectra, performed on the xenon clathrate of Dianin's compound were obtained under high-resolution Magic-Angle Spinning (MAS) conditions, by recoupling the weak (129)Xe-(129)Xe dipole-dipole couplings that exist between xenon atoms in close spatial proximity. Because the (129)Xe-(129)Xe dipole-dipole couplings are generally weak due to dynamics of the atoms and to large internuclear separations, and since the (129)Xe Chemical Shift Anisotropy (CSA) tends to be relatively large, a very robust dipolar recoupling sequence was necessary, with the symmetry-based SR26 dipolar recoupling sequence proving appropriate. We have also attempted to measure the (129)Xe-(129)Xe dipole-dipole coupling constant between xenon atoms in the cavities of the xenon-Dianin's compound clathrate and have found that the dynamics of the xenon atoms (as investigated with molecular dynamics simulations) as well as (129)Xe multiple spin effects complicate the analysis. The double quantum NMR method is useful for peak assignment in (129)Xe NMR spectra because peaks arising from different types of absorption/inclusion sites or from different levels of occupancy of single sites can be distinguished. The method can also help resolve ambiguities in diffraction experiments concerning the order/disorder in a material.     

MCM-41分子筛的合成及129Xe核磁共振的研究

ＭＣＭ４１中孔分子筛是１９９２年由Ｍｏｂｉｌ公司的科学家Ｋｒｅｓｇｅ［１］等人首次合成的,并在《自然》杂志发表。这种中孔分子筛具有六角形孔径,孔径２ｎｍ～１０ｎｍ,这种分子筛的孔径可以通过水晶模板来控制［２］。已报道的合成ＭＣＭ４１,孔径一般在２．０ｎｍ～３．５ｎｍ,使用的水晶模板一般是单一或两种阳离子季铵盐表面活性剂［３,４］。本论文通过引入第二种扩孔模板,与阳离子季铵盐协同作用,合成了孔径５．２ｎｍ（ＢＥＴ法测）的ＭＣＭ４１。通过氮气的吸脱附,测定了分子筛的比表面和孔径等性质。Ｊ．Ｆｒａｉｓｓａｒｄ…     

129Xe nuclear magnetic resonance study of pitch-based activated carbon modified by air oxidation/pyrolysis cycles: a new approach to probe the micropore size

(129)Xe NMR has been used to study a series of homologous activated carbons obtained from a KOH-activated pitch-based carbon molecular sieve modified by air oxidation/pyrolysis cycles. A clear correlation between the pore size of microporous carbons and the (129)Xe NMR of adsorbed xenon is proposed for the first time. The virial coefficient delta(Xe)(-)(Xe) arising from binary xenon collisions varied linearly with the micropore size and appeared to be a better probe of the microporosity than the chemical shift extrapolated to zero pressure. This correlation was explained by the fact that the xenon collision frequency increases with increasing micropore size. The chemical shift has been shown to vary very little with temperature (less than 9 ppm) for xenon trapped inside narrow and wide micropores. This is indicative of a smooth xenon-surface interaction potential.     

Potential of <Superscript>129</Superscript>Xe NMR spectroscopy of adsorbed xenon for testing the chemical state of the surface of mesoporous carbon materials illustrated by the example of aggregates of diamond and onion-like carbon nanoparticles

The chemical shift in the ¹²⁹Xe NMR spectrum of adsorbed xenon is very sensitive to the presence of oxygen-containing functional groups on the surface of mesoporous carbon materials. Well-characterized, structurally similar nanodiamond and onion-like carbon samples are considered here as model objects.     

2D 129Xe EXSY of xenon atoms in a thermotropic liquid crystal confined to a controlled-pore glass

Two-dimensional (129)Xe exchange spectroscopy (EXSY) NMR measurements are presented for xenon atoms dissolved in a thermotropic nematic Liquid Crystal (LC), Merck Phase 4, confined to a mesoporous Controlled-Pore Glass (CPG) material with an average pore diameter of 81 A. Experiments were carried out as a function of mixing time at two different temperatures in which Phase 4 appears in nematic and isotropic phases. The exchange rate constants of xenon atoms between two different sites were determined utilizing the intensities of diagonal and off-diagonal signals measured in the EXSY spectra. In the studied system, the sites are: (a) xenon dissolved in the bulk LC between the CPG particles; and (b) xenon in the LC confined inside the pores. The diffusion rate of xenon atoms between the various sites was observed to be very slow.     

Behavior of acetonitrile confined to mesoporous silica gels as studied by 129Xe NMR: a novel method for determining the pore sizes

129Xe NMR spectra of xenon dissolved in acetonitrile confined into three mesoporous silica gels with nominal pore diameters of 40, 60, and 100 A have been measured over the temperature range 170-245 K. The spectra consist of a number of lines, which contain detailed information on the system. The most interesting result is that the chemical shift of a particular signal observed below the melting point of confined acetonitrile is highly sensitive to the pore size, and hence its shape is sensitive to the pore size distribution function. This signal originates from the xenon atoms sited in very small cavities built up inside the pores during the freezing transition. It can be used to determine the size or even the size distribution function of the pores. In addition, the emergence of this signal reveals the phase transition temperature of acetonitrile inside the pores, which can also be used to determine the size of the pores. The difference in the chemical shifts of two other signals, which arise from xenon dissolved in bulk and confined acetonitrile, provides still another novel method for determining the size of the pores.     

Probing polymer colloids by Xe NMR

Model aqueous dispersions of polystyrene, poly(methyl methacrylate), poly(n-butyl acrylate) and a statistical copolymer poly(n-butyl acrylate-co-methyl methacrylate) were studied using xenon NMR spectroscopy. The ¹²⁹Xe NMR spectra of these various latexes reveal qualitative and quantitative differences in the number of peaks and in their line widths and chemical shifts. Above the glass transition temperature, exchange between xenon sorbed in the particle core and free xenon outside the particles is fast on the ¹²⁹Xe spectral time-scale and a single ¹²⁹Xe signal is observed. At temperatures below the glass transition temperature, the exchange between sorbed and free xenon is slow on the ¹²⁹Xe spectral time-scale and two ¹²⁹Xe NMR signals can be observed. If the signal of sorbed ¹²⁹Xe is observed, its chemical shift, line width and integral relative to the integral of free ¹²⁹Xe can be used for the characterization of the particle core. The line width of free ¹²⁹Xe provides the residence time of xenon outside the particles and can be used to determine the rate constant characterizing the kinetics of penetration of xenon in the particles. This rate constant emerges as promising parameter for the characterization of the polymer particle surface.     

MCM-41分子筛的合成及129Xe核磁共振的研究

Purely siliceous MCM-41 with a narrow pore-size distribution, different pore size, high surface area was synthesized . As prepared, calcined and catalytically tested MCM-41 materials have been comprehensively characterized by N₂ adsorption/desorption at 77K and ¹²⁹Xe NMR. By adding mesitylene during the synthesis, the pore size of MCM-41 was enlarged to 5.2nm. The chemical shift in ¹²⁹Xe NMR spectroscopy of adsorbed xenon indicates that the MCM-41 is one dimensional pore channels .     

Xenon porometry at room temperature

Xenon porometry is a method in which porous material is immersed in a medium and the properties of the material are studied by means of 129Xe nuclear magnetic resonance (NMR) of xenon gas dissolved in the medium. For instance, the chemical shift of a particular signal (referred to as signal D) arising from xenon inside small pockets formed in the pores during the freezing of the confined medium is highly sensitive to the pore size. In the present study, we show that when naphthalene is used as the medium the pore size distribution of the material can be determined by measuring a single one-dimensional spectrum near room temperature and converting the chemical shift scale of signal D to the pore radius scale by using an experimentally determined correlation. A model has been developed that explains the curious behavior of the chemical shift of signal D as a function of pore radius. The other signals of the spectra measured at different temperatures have also been identified, and the influence of xenon pressure on the spectra has been studied. For comparison, 129Xe NMR spectra of pure xenon gas adsorbed to porous materials have been measured and analyzed.     

Solid-state 129Xe and 131Xe NMR study of the perxenate anion XeO(6)4-

Results of the first solid-state 131Xe NMR study of xenon-containing compounds are presented. The two NMR-active isotopes of xenon, 129Xe (I=1/2) and 131Xe (I=3/2), are exploited to characterize the xenon magnetic shielding and quadrupolar interactions for two sodium perxenate salts, Na4XeO6.xH2O (x=0, 2), at an applied magnetic field strength of 11.75 T. Solid-state 129/131Xe NMR line shapes indicate that the local xenon environment in anhydrous Na4XeO6 adopts octahedral symmetry, but upon hydration, the XeO6(4-) anion becomes noticeably distorted from octahedral symmetry. For stationary, anhydrous samples of Na4XeO6, the heteronuclear 129/131Xe-23Na dipolar interaction is the principal contributor to the breadth of the 129/131Xe NMR lines. For stationary and slow magic-angle-spinning samples of Na4XeO(6).2H2O, the anisotropic xenon shielding interaction dominates the 129Xe NMR line shape, whereas the 131Xe NMR line shape is completely dominated by the nuclear quadrupolar interaction. The xenon shielding tensor is approximately axially symmetric, with a skew of -0.7+/-0.3, an isotropic xenon chemical shift of -725.6+/-1.0 ppm, and a span of 95+/-5 ppm. The 131Xe quadrupolar coupling constant, 10.8+/-0.5 MHz, is large for a nucleus at a site of approximate Oh symmetry, and the quadrupolar asymmetry parameter indicates a lack of axial symmetry. This study demonstrates the extreme sensitivity of the 131Xe nuclear quadrupolar interaction to changes in the local xenon environment.     

129Xe NMR study of the localization of PdCl2 supported on carbon nanotubes

Localization of PdCl₂ clusters supported on multi-wall carbon nanotubes (MWCNT) has been investigated using ¹²⁹Xe NMR of adsorbed xenon. As-made MWCNTs with channels initially inaccessible for adsorption and ball-milled MWCNTs with the totally accessible internal surface were used as supports. The observed ¹²⁹Xe NMR spectra were determined by the dynamics of xenon exchange between the aggregate pores and nanotube channels. No considerable changes of the ¹²⁹Xe NMR spectrum with the concentration of supported PdCl₂ were observed for the as-made MWCNT, while an additional resonance appeared for the ball-milled nanotubes. The ¹²⁹Xe NMR experiments evidenced the supported species to be localized on the internal surface of the ball-milled MWCNT.     

Probing the interaction of solvents with the stationary phase of C18 high-performance liquid chromatographic column material by variable-temperature dependent 129Xe nuclear magnetic resonance spectroscopy

VT (129)Xe NMR was applied to probe the interactions of solvents having different polarity indices with the stationary phase of a RP-C18 HPLC column material. It was observed that the highly polar ethylene glycol molecules do not mix with the alkyl chains of the RP-C18 stationary phase and the solvent is unable to enter the pores and the spaces between the particles. Three phases in this sample are defined as stationary/xenon phase, xenon gas phase (in the pores and the spaces between the particles) and ethylene glycol/xenon phase. In contrast to ethylene glycol, the nonpolar solvent cyclohexane was observed to be well mixed with the RP-C18 stationary phase. The capillary rise effect allows the solvent to enter the pores and the spaces between the particles. Two phases in this sample are defined as stationary/cyclohexane/xenon phase and cyclohexane/xenon phases. The properties of ethyl acetate are between those of ethylene glycol and cyclohexane. The (129)Xe NMR results show that the rational reversed phases should be conditioned from highly solvating to more polar solvents to remove the trapped air. The (129)Xe NMR results also show that pure stationary phase exists only when a highly polar solvent is used in reversed-phase chromatography. For a solvent with lower polarity, a stationary/solvent phase actually forms. This, together with the mobile phase, determines the selective factor for separating mixtures.     

超极化129Xe核磁共振技术及其在多孔催化材料研究中的应用

 激光抽运和自旋交换的超极化 129Xe 核磁共振是近几年发展起来的一种新方法,它比普通 129Xe 核磁共振的检测灵敏度提高约104 ～105倍,是研究材料孔结构和孔内粒子分布的强有力工具. 本文介绍了超极化 129Xe 核磁共振技术并综述了其在多孔催化材料研究中的应用,特别是对催化反应中广泛使用的无机微孔和介孔材料中的应用进行了详细的讨论. 最后展望了此技术的应用前景.     

Fine-tuning the degree of organic functionalization of mesoporous silica nanosphere materials via an interfacially designed co-condensation method

A synthetic method that can fine tune the amount of chemically accessible organic functional groups on the pore surface of MCM-41 type mesoporous silica nanosphere (MSN) materials has been developed by electrostatically matching various anionic organoalkoxysilanes with the cationic cetyltrimethylammonium bromide micelles in a base-catalyzed condensation reaction of tetraethoxysilane.     

129Xe NMR Studies of Pecan Shell-Based Biochar and Structure-Process Correlations

Pecan shell-based biochar is utilized as a filtration medium, sequestrant for metallic ions, soil conditioner, and other applications. One process for creating the biochar involves the use of phosphoric acid at high temperature in a partial oxygen atmosphere to produce a highly porous carbonaceous material. In this work, we found ¹²⁹Xe NMR to be an excellent technique to study micropores in biochar. Thus, the ¹²⁹Xe chemical shift in biochar was found to vary linearly with the xenon pressure; from the data an estimate of about 8–9 Å could be proposed for the average pore diameter in pecan shell-based biochar. Through saturation recovery and 2-D NMR exchange experiments, information on the exchange between free versus bound xenon was obtained. Furthermore, correlations of ¹²⁹Xe NMR data with the carbonization process conditions were made.     

Characterization of the metal-organic framework compound Cu3(benzene 1,3,5-tricarboxylate)2 by means of 129Xe nuclear magnetic and electron paramagnetic resonance spectroscopy

129Xe NMR measurements of adsorbed xenon are shown for the first time to be a suitable tool to characterize the porosity and the properties of the metal-organic framework Cu3(BTC)2(H2O)3 (BTC = benzene 1,3,5-tricarboxylate). The NMR experiments are performed at room temperature and over a wide range of xenon pressure and on two different synthesized Cu3(BTC)2 samples. 129Xe NMR results reveal that in dependence on the kind of the synthesis pathway either one or two signals are observed which can be attributed to two kinds of fast exchange of xenon atoms in two pores with different pore sizes. Coadsorption experiments of xenon and ethylene demonstrate that the xenon atoms prefer to fill the greater pores of the material because the smaller pores are occupied with residual molecules from the synthesis procedure and additionally adsorbed ethylene. Besides the NMR experiments a series of electron paramagnetic resonance (EPR) measurements are performed to estimate the state of copper having a strong influence on the chemical shift of the adsorbed xenon. The EPR experiments demonstrate that spin exchange between the interconnected copper dimers is taking place across the BTC linker molecules in the Cu3(BTC)2 framework.     

Probing the geometry and interconnectivity of pores in organic aerogels using hyperpolarized 129XE NMR spectroscopy

Hyperpolarized (HP) 129Xe NMR was used for the first time to probe the geometry and interconnectivity of pores in RF aerogels and to correlate them with the [resorcinol]/[catalyst] (R/C) ratio. We have demonstrated that HP 129Xe NMR is an ideal method for accurately measuring the volume-to-surface-area (Vg/S) ratios for soft mesoporous materials without using any geometric models. The Vg/S parameter, which is related both to the geometry and the interconnectivity of the porous space, has been found to correlate strongly with the R/C ratio and exhibits an unusually large span: an increase in the R/C ratio from 50 to 500 results in about 5-fold rise in Vg/S. Unlike conventional techniques, HP 129Xe NMR spectroscopy probes the geometry and interconnectivity of the nano- or mesopores in soft materials, providing new insights into the pore structure.     

Grand canonical Monte Carlo simulations of the 129Xe NMR line shapes of xenon adsorbed in (+/-)-[Co(en)3]Cl3

The 129Xe NMR line shapes of xenon adsorbed in the nanochannels of the (+/-)-[Co(en)3]Cl3 ionic crystal have been calculated by grand canonical Monte Carlo (GCMC) simulations. The results of our GCMC simulations illustrate their utility in predicting 129Xe NMR chemical shifts in systems containing a transition metal. In particular, the nanochannels of (+/-)-[Co(en)3]Cl3 provide a simple, yet interesting, model system that serves as a building block toward understanding xenon chemical shifts in more complex porous materials containing transition metals. Using only the Xe-C and Xe-H potentials and shielding response functions derived from the Xe@CH4 van der Waals complex to model the interior of the channel, the GCMC simulations correctly predict the 129Xe NMR line shapes observed experimentally (Ueda, T.; Eguchi, T.; Nakamura, N.; Wasylishen, R. E. J. Phys. Chem. B 2003, 107, 180-185). At low xenon loading, the simulated 129Xe NMR line shape is axially symmetric with chemical-shift tensor components delta(parallel) = 379 ppm and delta(perpendicular) = 274 ppm. Although the simulated isotropic chemical shift, delta(iso) = 309 ppm, is overestimated, the anisotropy of the chemical-shift tensor is correctly predicted. The simulations provide an explanation for the observed trend in the 129Xe NMR line shapes as a function of the overhead xenon pressure: delta(perpendicular) increased from 274 to 292 ppm, while delta(parallel) changed by only 3 ppm over the entire xenon loading range. The overestimation of the isotropic chemical shifts is explained based upon the results of quantum mechanical 129Xe shielding calculations of xenon interacting with an isolated (+/-)-[Co(en)3]Cl3 molecule. The xenon chemical shift is shown to be reduced by about 12% going from the Xe@[Co(en)3]Cl3 van der Waals complex to the Xe@C2H6 fragment.     

High-pressure in situ 129Xe NMR spectroscopy and computer simulations of breathing transitions in the metal-organic framework Ni2(2,6-ndc)2(dabco) (DUT-8(Ni))

Recently, we have described the metal-organic framework Ni(2)(2,6-ndc)(2)(dabco), denoted as DUT-8(Ni) (1) (DUT = Dresden University of Technology, 2,6-ndc = 2,6-naphthalenedicarboxylate, dabco = 1,4-diazabicyclo[2.2.2]octane). Upon adsorption of molecules such as nitrogen and xenon, this material exhibits a pronounced gate-pressure effect which is accompanied by a large change of the specific volume. Here, we describe the use of high-pressure in situ (129)Xe NMR spectroscopy, i.e., the NMR spectroscopic measurements of xenon adsorption/desorption isotherms and isobars, to characterize this effect. It appears that the pore system of DUT-8(Ni) takes up xenon until a liquid-like state is reached. Deeper insight into the interactions between the host DUT-8(Ni) and the guest atom xenon is gained from ab initio molecular dynamics (MD) simulations. van der Waals interactions are included for the first time in these calculations on a metal-organic framework compound. MD simulations allow the identification of preferred adsorption sites for xenon as well as insight into the breathing effect at a molecular scale. Grand canonical Monte Carlo (GCMC) simulations have been performed in order to simulate adsorption isotherms. Furthermore, the favorable influence of a sample pretreatment using solvent exchange and drying with supercritical CO(2) as well as the influence of repeated pore opening/closure processes, i.e., the "aging behavior" of the compound, can be visualized by (129)Xe NMR spectroscopy.