Determination of trace levels of iron in a seawater sample using isotope dilution/inductively coupled plasma mass spectrometry.

An analytical method for trace levels of iron in a seawater sample using isotope dilution ICP-MS was developed. Preconcentration of iron and the removal of major elements in seawater such as alkali and alkaline-earth elements can be carried out quickly using a chelating resin disk by adjusting the sample pH to 3. The collision cell option of the ICP-MS instrument method was used to improve the performance of the instrument for iron measurements since ArO and ArN interferences could be reduced using this analytical method. About 4 ml min(-1) helium, as the collision gas, were introduced into the cell. 40Ar14N and 40Ar16O which interfere with 54Fe and 56Fe in water had their amounts decreased by 5 orders of magnitude. Then, the isotope dilution method was used for iron determination below ng g(-1) level of trace iron in four environmental reference materials (river water standard sample JAC-0031 (Japan Soc. for Analytical Chemistry), estuarine standard sample SLEW-2 (NRC Canada) and seawater standard samples CASS-3 and NASS-5 (NRC Canada)) were measured. Good agreement between analytical results and certified values of reference materials was obtained, which confirmed the effectiveness of this method.     

Comparison of NAA and ICP-MS for the determination of major and trace elements in environmental sample

Summary Major and trace elements in soil and plant samples, including standard reference materials were determined by means of neutron activation analysis (NAA) and inductively coupled plasma-mass spectrometry (ICP-MS). The analytical procedure for NAA utilized dried powder samples. The concentration of iodine in soil samples was determined by radiochemical NAA. The irradiated samples were cooled and then counted with a Ge gamma-ray detector connected to a multi-channel analyzer. For ICP-MS analysis, the samples were decomposed by microwave digestion with an acid mixture. The concentration of I in the soil samples was measured by ICP-MS after separation by ignition. The analytical values for most elements in the environmental samples by both methods were in good agreement, whereas sample treatments were different. Measured value of Zr in the soil samples by ICP-MS was about 50% lower than that by NAA. It should be assumed that some minerals of Zr in soil particles were not entirely dissolved by the acid mixture. Analytical results of Cd for three different Cd levels in unpolished rice flour samples (NIES 10-a, b and c) determined by ICP-MS were in agreement with certified values. The concentration of Cd in the sample with the lowest Cd level, as determined by NAA with 57% counting error, was 3 times higher than the certified value.     

Determination of heavy metals and rare earth elements in environmental samples by ICP-MS after solid phase preconcentration with chelating resin fibers and anion exchanger filters.

A solid phase collection/concentration method using anion exchanger filters and a small syringe packed with chelating resin fibers is adopted as a preconcentration tool for trace elements and a separation tool for matrices in aqueous samples prior to the measurement by inductively coupled plasma-mass spectrometry (ICP-MS). The effects of fiber volume, sample volume, eluent volume, and sample flow rate on metal recoveries were investigated in detail to obtain optimum pretreatment conditions. Several heavy metals (HMs) such as, V, Mn, Co, Ni, Cu, Zn, Ga, Cd, Pb, Th and U, as well as 14 rare earth elements (REEs) in sample solutions at pH 6 were quantitatively collected on the solid phase. These adsorbed elements were completely recovered by eluting with 2 ml of 1.0 M nitric acid. At pH 6, more than 99% of alkali and alkaline earth metals in sample solutions were eliminated. The proposed method was evaluated by analyzing two standard reference materials (SRM): peach leaves (NIST 1547) and pond sediment (NIES No. 2). The solid samples were decomposed by microwave-heating and pressurizing acid digestion technique, and then treated by the proposed syringe-type pretreatment method, followed by the ICP-MS measurement. The analytical results for HMs in the SRMs obtained by the present method agreed well with the certified values.     

Inductively coupled plasma mass spectrometric determination of heavy metals in sea-water samples after pre-treatment with a chelating resin disk by an on-line flow injection method

A new on-line flow injection (FI) pre-treatment system using a disk-type chelating resin (5 mm diameter, 0.5 mm thickness) was developed for the simultaneous multi-element determination of trace metals in sea-water samples by inductively coupled plasma mass spectrometry (ICP-MS). A chelating resin possessing an iminodiacetate (IDA) functional group was used for the collection of trace elements and the elimination of alkali and alkaline earth metals in highly concentrated salt solution. A 1 ml volume of a sea-water sample (pH 5.5) was applied to the chelating resin disk. Considering the removal efficiency for Ca, 50 mM ammonium acetate buffer solution (pH 5.5) was chosen as a sample carrier. The enriched trace metals were eluted with 0.1 M nitric acid and the eluate flowed into the ICP-MS system. The processing time for one sample was < 6 min (350 s). One of the important observations is the possibility of working with a low recovery, even lower than 50%. For example, several elements such as Mn, Cr, As, Mo, Ba and U, the recovery of which was < 50% in a batch-wise method, showed good linearity and reproducibility. The proposed method was evaluated by analyzing two kinds of sea-water certified reference materials, CASS-4 and NASS-5. Analytical data for eight heavy metals, V, Mn, Co, Ni, Cu, Mo, Cd and U, obtained from the present study agreed well with the certified values.     

Development of multi-elemental method for quality control of parenteral component solutions using ICP-MS

An inductively coupled plasma mass spectrometry (ICP-MS) method for elemental impurities determination in components used for parenteral nutrition solutions is proposed. Solutions of amino acids (10% m/v), glucose (50% m/v) and lipids (20% m/v) were analyzed. Arsenic, Cd, Cu, Pb and Mo were determined by ICP-MS operated at standard mode, whilst pneumatic nebulization was used for introducing the sample solution into the ICP. Mercury was determined using cold vapor generation (CVG) coupled to ICP-MS. Chromium, Mn, Ni and V were determined by means of dynamic reaction cell-inductively coupled plasma mass spectrometry (DRC-ICP-MS), while ammonia was used as reaction gas. The operational conditions of each technique were optimized in order to achieve better sensitivity, precision and accuracy. The influence of the sample matrix, mainly carbon, on all investigated elements was evaluated. The use of DRC was effective to reduce interferences on Cr, Mn, Ni and V determination. The other investigated elements (As, Cd, Cu, Pb, Mo and Hg) were determined directly in the samples, which were properly diluted. Results obtained were in good agreement (between 96 and 103%) with certified values (certified reference materials of water were analyzed), at the same time as the relative standard deviation was lower than 5%. Sample throughput was relatively high (up to 30 samples of components used for parenteral nutrition solution could be analyzed per hour). In this way, the proposed method can be recommended for routine analysis.     

Preconcentration and determination of trace metals in seawater using a thiol cotton fiber minicolumn coupled with inductively coupled plasma mass spectrometry.

A rapid separation and preconcentration method was developed for the determination of trace metals Cu, Zn, Cd, and Pb in seawater using a minicolumn packed with thiol cotton fiber (TCF) coupled with inductively coupled plasma mass spectrometry (ICP-MS). Preconcentration parameters, such as seawater sample volume and flow rate and eluent hydrochloric acid concentration, volume and flow rate, were optimized. Under the optimized conditions, trace metals Cu, Zn, Cd, and Pb in seawater can be determined with no interference from saline matrices. When a sample volume of 1500 ml and a sample flow rate of 15 ml min(-1) were used, the preconcentration factor of 1500 and RSD value of <7% at ng ml(-1) were achieved. The accuracy of the recommended method was verified by the analysis of certified reference materials.     

Application of laser ablation ICP-MS to elemental analysis of glasses

A technique involving the coupling of laser ablation and inductively coupled plasma mass spectrometer has been used for semi-quantitative analysis of glasses without sample dissolution. The characteristic features of this technique is low detection limit and accuracy between a few % up to 20%. An NIST glass standard (SRM 612) was dissolved and then analysed by ICP-MS in semi-quantitative mode. The results were in close agreement with the certified values for elements such as Mn, Sr, Y, Ti...Abbreviations AA atomic absorption - ICP-OES inductively coupled plasma optical emission spectroscopy - ICP-MS inductively coupled plasma mass spectrometry - LA laser ablation     

High-throughput determination of seven trace elements in food samples by inductively coupled plasma-mass spectrometry

A method was developed for high-throughput determinations of 7 elements in food samples, namely antimony (Sb), arsenic (As), cadmium (Cd), chromium (Cr), lead (Pb), mercury (Hg), and tin (Sn). The samples were digested by closed-vessel microwave-assisted digestion using concentrated nitric acid (HNO3) as the medium, followed by microwave- assisted evaporation to concentrate the sample solutions before dilution to the desired volume. The microwave-assisted evaporation procedure effectively reduced the final acid concentration to around 8% before analysis by inductively coupled plasma-mass spectrometry (ICP-MS). This reduction allows determination by ICP-MS to proceed without further sample dilution, which would affect the detection limit. The method was validated, and method recoveries for As, Cd, Cr, Pb, and Hg were within the certified ranges of the chosen certified reference materials. Recoveries of the 7 elements from spiked samples ranged from 93.1 to 103.6%. The standard uncertainties of precision for the 7 elements were between 3.1 and 4.3%. Interlaboratory comparison studies for As, Cd, and Pb gave z-scores ranging from -0.2 to 0.3.     

Assessment of the ICP-MS method using the interlaboratory QA study of two Polish soil RMs

 Under an international collaborative certification programme, two new Polish soil reference materials, PL-1 (loess) and BPGM-1 (sandy loam soil), were analysed for 34 trace elements including all the rare earth elements using the acid decomposition method and inductively coupled plasma - mass spectrometry (ICP-MS). After the certification by the organisers, the analytical data obtained at our institute were compared with the certified data. 'Z-score' values calculated for individual trace elements helped in the assessment of the quality of the data. While the majority of the data obtained on ICP-MS was very precise and accurate, some of the data especially for elements such as Zr, Hf and Nb suffered from incomplete dissolution of the sample and spectroscopic interferences. For some trace elements, certified data are not available for comparison. These features together with the usefulness of interlaboratory collaborative programmes and ICP-MS for the certification of soil reference materials are discussed. Received: 6 August 1999 / Accepted: 28 February 2000     

微波消解-电感耦合等离子体质谱法测定土壤中微量稀土元素

研究了电感耦合等离子体质谱（ＩＣＰ－ＭＳ）测定土壤中微量稀土元素（ＲＥＥｓ）的方法。详细讨论了测定稀土元素的质谱干扰及基体的抑制效应,采用高斯消除法可有效地校正质谱干扰,内标法可以补偿基体的抑制效应。     

Determination of platinum and rhodium in dust and plant samples using microwave-assisted sample digestion and ICP-MS

The platinum group elements (PGEs), particularly platinum, palladium and rhodium, are nowadays increasingly emitted into the environment from automotive catalytic converters. Thus, a method for the determination of PGEs (especially platinum and rhodium) in dust and plant samples was developed. The developed method was based on microwave-assisted sample digestion and inductively coupled plasma mass spectrometric (ICP-MS) determination. Spectral interferences in ICP-MS determination were corrected using mathematical correction equations based on signal ratio measurement. In addition, platinum and rhodium concentrations in the digested dust samples were also determined after Te coprecipitation without correction of the interferences. The results for platinum and rhodium in reference materials (NIST SRM 2557, recycled monolith autocatalyst and BCR-723, road dust) were in good agreement with the certified values. Preliminary results for the anthropogenic platinum and rhodium emissions in Oulu, northern Finland, based on dust and plant samples, indicated a common traffic-related source of these metals.     

电感耦合等离子体质谱法分析粉煤灰漂珠中的微量元素

建立了一种电感耦合等离子体质谱法测定粉煤灰漂珠中微量元素的方法,检出限为0.002~0.01 ng/mL,相对标准偏差为1.4%~2.5%(n=10)。用该方法分析了标准物质(GBW 07103)和德州、衡水的粉煤灰漂珠样品中的微量元素,标准物质分析结果与参考值一致,实际样品加标回收率为87.9%~105.6%。     

Open-channel chip-based solid-phase extraction combined with inductively coupled plasma-mass spectrometry for online determination of trace elements in volume-limited saline samples

In this study, we used an automated online chip-based solid-phase extraction (SPE)-inductively coupled plasma-mass spectrometry (ICP-MS) system for analyzing trace elements in small-volume saline samples (～15 μL). The proposed method involved the adsorption of trace metal ions in the interior of a functionalized poly(methyl methacrylate) (PMMA) channel in order to separate these ions from saline matrices. The adsorption of transition metal ions was presumably dominated by the surface complexation between the carboxylate moieties in the interior of the PMMA channel and the metal ions, which facilitated the formation of metal-carboxylate complexes. The components of the proposed online analytical system used for the simultaneous detection of multiple trace metals in saline samples involved microdialysis (MD) sampling, an established chip-based SPE procedure, and ICP-MS. The SPE-ICP-MS hyphenated system was optimized, and then, the analytical reliability of this system was further confirmed by using it to analyze the certified reference materials-SRM 2670 (human urine) and SRM 1643e (artificial saline water). The satisfactory analytical results indicated that the proposed on-chip SPE device could be readily used as an interface for coupling the MD probe with the ICP-MS system. The dramatically reduced consumption of chemicals and "hands-on" manipulations enabled the realization of a simplified and relatively clean procedure with extremely low detection limits in the range of 5.86-76.91 ng L(-1) for detecting Mn, Co, Ni, Cu, and Pb in 15-μL samples by ICP-MS. The effectiveness of an online MD-chip-based SPE-ICP-MS technique for continuous monitoring of trace elements in a simulated biological system was also demonstrated. To the best of our knowledge, this is the first paper to report the direct exploitation of a PMMA chip as an SPE adsorbent for online sample pretreatment and trace metal preconcentration prior to ICP-MS measurement.     

Determination of Pt from coke samples by ICP-MS after microwave assisted digestion and microwave assisted cloud point extraction

Platinum in coke samples was determined by inductively coupled plasma mass spectrometry (ICP-MS) after microwave-assisted sample digestion and temperature controlled microwave assisted cloud point extraction (MW-CPE). Interferences due to hafnium (¹⁷⁹Hf¹⁶O) were successfully eliminated using MW-CPE with 2-MBT prior to the determination of platinum by ICP-MS. The validity of the method was studied by spike recovery tests and by analyzing certified reference material (BCR-723 street dust). The results obtained for platinum in the BCR-723 were generally in good agreement with the certified values. Furthermore, the preliminary platinum results obtained for coke sample by ICP-MS after MW-CPE were compared to those obtained by a reference method (NiS-Fire Assay preconcentration/Te coprecipitation and ICP-MS determination).     

Synthesis of cross-linked chitosan modified with the glycine moiety for the collection/concentration of bismuth in aquatic samples for ICP-MS determination.

A chelating resin, cross-linked chitosan modified with the glycine moiety (glycine-type chitosan resin), was developed for the collection and concentration of bismuth in aquatic samples for ICP-MS measurements. The adsorption behavior of bismuth and 55 elements on glycine-type chitosan resin was systematically examined by passing a sample solution containing 56 elements through a mini-column packed with the resin (wet volume; 1 ml). After eluting the elements adsorbed on the resin with nitric acid, the eluates were measured by ICP-MS. The glycine-type chitosan resin could adsorb several cations by a chelating mechanism and several oxoanions by an anion-exchange mechanism. Especially, the resin could adsorb almost 100% Bi(III) over a wide pH region from pH 2 to 6. Bismuth could be strongly adsorbed at pH 3, and eluted quantitatively with 10 ml of 3 M nitric acid. A column pretreatment method with the glycine-type chitosan resin was used prior to removal of high concentrations of matrices in a seawater sample and the preconcentration of trace bismuth in river water samples for ICP-MS measurements. The column pretreatment method was also applied to the determination of bismuth in real samples by ICP-MS. The LOD of bismuth was 0.1 pg ml(-1) by 10-fold column preconcentration for ICP-MS measurements. The analytical results for bismuth in sea and river water samples by ICP-MS were 22.9 +/- 0.5 pg ml(-1) (RSD, 2.2%) and 2.08 +/- 0.05 pg ml(-1) (RSD, 2.4%), respectively.     

SI-traceable certification of the IMEP-12 water sample combining contributions from different reference laboratories

In the International Measurement Evaluation Programme (IMEP-12) comparison, a synthetically prepared water sample was offered to the analytical laboratories to perform measurements of As, B, Cd, Cr, Cu, Fe, Mg, Mn, Ni and Pb. The choice of elements to be measured was based on EU legislation, which the comparison was aiming to support. As to the IMEP policy, the laboratories’ results were presented according to the certified/assigned reference values established by several reference laboratories all around the world. The performed certification campaign is described in detail in this paper. Isotope dilution mass spectrometry (IDMS) was applied as a primary method of measurement (PMM), whenever possible, to achieve SI-traceable results. Apart from IDMS for reference measurements of some elements, k _o-neutron activation analysis (k _o-NAA) and external calibration (Ext-Calib) using inductively coupled plasma-mass spectrometry (ICP-MS) were applied. The reference values were characterised as “certified” (for B, Cd, Cr, Cu, Fe, Mg, Ni and Pb) or “assigned” (for As and Mn) according to the IMEP policy. Measurement uncertainty of the certified/assigned reference values was calculated according to the ISO/BIPM guide using the specialised software GUM Workbench.

     

SI-traceable certification of the IMEP-12 water sample combining contributions from different reference laboratories

In the International Measurement Evaluation Programme (IMEP-12) comparison, a synthetically prepared water sample was offered to the analytical laboratories to perform measurements of As, B, Cd, Cr, Cu, Fe, Mg, Mn, Ni and Pb. The choice of elements to be measured was based on EU legislation, which the comparison was aiming to support. As to the IMEP policy, the laboratories’ results were presented according to the certified/assigned reference values established by several reference laboratories all around the world. The performed certification campaign is described in detail in this paper. Isotope dilution mass spectrometry (IDMS) was applied as a primary method of measurement (PMM), whenever possible, to achieve SI-traceable results. Apart from IDMS for reference measurements of some elements, k _o-neutron activation analysis (k _o-NAA) and external calibration (Ext-Calib) using inductively coupled plasma-mass spectrometry (ICP-MS) were applied. The reference values were characterised as “certified” (for B, Cd, Cr, Cu, Fe, Mg, Ni and Pb) or “assigned” (for As and Mn) according to the IMEP policy. Measurement uncertainty of the certified/assigned reference values was calculated according to the ISO/BIPM guide using the specialised software GUM Workbench.     

微波消解-电感耦合等离子体质谱法检测土壤中16种稀土元素

建立了微波消解-电感耦合等离子体质谱法(ICP-MS)测定土壤样品中16种稀土元素的分析方法。样品经硝酸-过氧化氢-氢氟酸消解,直接用ICP-MS测定试液中16种稀土元素。研究了ng/mL水平的Ba氧化物及轻稀土氧化物对重稀土元素的干扰程度,其中Ba和Pr的氧化物干扰较严重,不过此类干扰可通过Method编辑干扰方程得以校正。测定土壤标准物质GBW07446及GBW07451,结果与标准物质证书值一致。     

Evaluation of closed-vessel microwave digestion method for the determination of trace impurities in polymer-based photoresist by inductively coupled plasma mass spectrometry

A closed microwave digestion method followed by inductively coupled plasma spectrometric (ICP-MS) analysis was evaluated for the determination of trace impurities in photoresist. To optimize the digestion procedure, several digestion parameters such as acid, heating temperature and heating time were evaluated. Besides, the digestion efficiency of used photoresist material and the recovery of analyte elements obtained by the use of gravimetric method and ICP-MS measurement, individually, were also compared to clarify the completeness of digestion. According to our experiments, the gravimetric method was found to be not so relevant to the completeness of digestion, because the remaining sample matrix could cause suppression effect in the subsequent ICP-MS measurement. In view of minimizing blank value and working time, a simple single-step heating program was proposed to mineralize 0.25 ml of photoresist material with 5 ml of nitric acid at 180 °C for 10 min. Based on the comparative study of the analytical results obtained by instrumental neutron activation analysis (INAA) and proposed method, the reliability of proposed method for the determination of trace metallic impurities in photoresist material has been confirmed.     

Determination of total urinary mercury by on-line sample microwave digestion followed by flow injection cold vapour inductively coupled plasma mass spectrometry or atomic absorption spectrometry

The total mercury content in urine was determined by inductively coupled plasma mass spectrometry with the so-called cold vapour method after on-line oxidative treatment of the sample in a microwave oven (FI-MW-CV-ICPMS). Use of a KBr/KBrO(3) mixture, microwave digestion, and the final oxidation with KMnO(4), assure the complete recovery of the organic forms of Hg which would be difficult to determine otherwise if using only the CV-ICPMS apparatus. Quantitative recoveries were obtained for phenyl Hg chloride (PMC), dimethyl Hg (DMM), Hg acetate (MA) and methyl Hg chloride (MMC). Use of automatic flow injection microwave systems (FI-MW) for sample treatment reduces environmental contamination and allows detection limits suitable for the determination of reference values. Since no certified reference materials were commercially available in the concentration ranges of interest, the accuracy of the proposed procedure has been assessed by analysing a series of urine samples with two independent techniques, ICP-MS and AAS. When using the FI-MW-CV-ICP-MS technique, the detection limit was assessed at 0.03microg/L Hg, while with FI-MW-CV-AAS it was 0.2microg/L Hg. The precision of the method was less than 2-3% for FI-MW-CV-ICP-MS and about 3-5% for FI-MV-CV-AAS at concentrations below 1microg/L Hg. These results show that ICP-MS can be considered as a "reference technique" for the determination of total urinary Hg at very low concentrations, such as are present in non-exposed subjects.