Sol–gel synthesis, characterization, and catalytic activity of Fe(III) titanates

Nanostructured iron–titanium mixed oxides with different Fe/Ti ratios were prepared by sol–gel methods under different preparative conditions. When equal molar amounts of Fe and Ti ions were employed, the product calcined at 500 °C showed an X-ray diffraction pattern that resembles Fe₂Ti₃O₉. On the other hand, lower Fe/Ti ratios favored the formation of Fe₂TiO₅ while higher ratios resulted in free α-Fe₂O₃ and TiO₂. Besides the effect of the Fe/Ti ratio, the composition of the final product was dependent on the preparative conditions and the calcination temperature. Enhancing the gelation process by heating or by employing an acid catalyst favored the formation of Fe₂TiO₅ at relatively low temperatures. Compared with the corresponding pure oxides, the prepared iron–titanium mixed oxides showed modified textural characteristics which were also dependent on the composition and the calcination temperature. The mixed oxides showed higher catalytic activity in the oxidation of methanol than their corresponding pure oxides with a noticeable enhanced oxidation potential forming methyl formate and carbon dioxide.     

Phase diagrams of the ternary systems Mn, Fe, Co, Ni---Si---N

Phase equilibria in the ternary systems Mn, Fe, Co, and Ni---Si---N are investigated and isothermal sections at 900°C (Fe---Si---N, Ni---Si---N), at 1000°C (Mn---Si---N, Co---Si---N) and at 1150°C (Fe---Si---N) are presented. In the system Mn---Si---N, Si₃N₄ coexists with MnSiN₂, Mn₃Si, Mn₅Si₃, MnSi, and MnSi_2−x. In the systems Fe, Co, Ni---Si---N, Si₃N₄ coexists with all binary silicides but reacts rapidly with iron above 1120 ± 10°C, and cobalt and nickel above 1170 ± 10°C to form binary silicides and nitrogen gas.     

TGA–FTIR study of a lead zirconate titanate gel made from a triol-based sol–gel system

A Pb(Zr,Ti)O₃ precursor gel made from a sol prepared using 1,1,1,-tris(hydroxymethyl)ethane, lead acetate and zirconium and titanium propoxides, stabilised with acetylacetone, was analysed using TGA–FTIR analysis. Decomposition under nitrogen (N₂) gave rise to evolved gas absorbance peaks at 215 °C, 279 °C, 300 °C and 386 °C, but organic vapours continued to be evolved, along with CO₂ and CO until 950 °C. The final TGA step in N₂ is thought to relate to decomposition of an intermediate carbonate phase and the final elimination of residues of triol or acetylacetonate species which form part of the polymeric gel structure. By contrast, heating in air promoted oxidative pyrolysis of the final organic groups at ≤450 °C. In air, an intermediate carbonate phase was decomposed by heating at 550 °C, allowing Pb(Zr,Ti)O₃ to be produced some 400 °C below the equivalent N₂ decomposition temperature.     

X-ray diffraction and Mössbauer spectroscopy studies of LiFe0.5Ti1.5O4 – A new primitive cubic ordered spinel

LiFe_0.5Ti_1.5O₄ was synthesized by solid-state reaction carried out at 900 °C in flowing argon atmosphere, followed by rapid quenching of the reaction product to room temperature. The compound has been characterized by X-ray powder diffraction (XRD) and ⁵⁷Fe Mössbauer effect spectroscopy (MES). It crystallizes in the space group P4₃32, a = 8.4048(1) Å. Results from Rietveld structural refinement indicated 1:3 cation ordering on the octahedral sites: Li occupies the octahedral (4b) sites, Ti occupies the octahedral (12d) sites, while the tetrahedral (8c) sites have mixed (Fe/Li) occupancy. A small, about 5%, inversion of Fe on the (4b) sites has been detected. The MES data is consistent with cation distribution and oxidation state of Fe, determined from the structural data.The title compound is thermally unstable in air atmosphere. At 800 °C it transforms to a mixture of two Fe³⁺ containing phases – a face centred cubic spinel Li_(1+y)/2Fe_(5−3y)/2Ti_yO₄ and a Li_(z−1)/2Fe_(7−3z)/2Ti_zO₅ – pseudobrookite. The major product of thermal treatment at 1000 °C is a ramsdellite type lithium titanium iron(III) oxide, accompanied by traces of rutile and pseudobrookite.     

Bioactive Ca10(PO4)6(OH)2−TiO2 composite coating prepared by sol-gel process

The sol-gel prepared titania (TiO₂) has recently been demonstrated with a promising bioactivity [1]. It forms a chemical bond with the living bone in the body, although the bonding is not very strong. The present study is intended to improve the bone-bonding ability of the titania gel. The goal is achieved by impregnating the titania with hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂). The processing route includes the following steps: (1) the titania sol solution was prepared; (2) the solution was mixed with fine hydroxyapatite (HA) powders; (3) the mixture was used to produce a coating on a commercial pure titanium (c.p. Ti) or Ti6A14V plate by a dip coating technique; (4) the coating was fired at 400–600°C. The resulting coating is a composite consisting of hydroxyapatite embedded in the matrix of the titania gel. Such HA-TiO₂ composite coating is capable of inducing the hydroxyapatite precipitation from a simulated body fluid. When implanted in femurs of goat, the composite coating shows a bonding with bone. Its bone-bonding strength is twice as high as that of the pure titania gel coating. The results indicate that impregnating with hydroxyapatite is a promising way to increase the bioactivity of the titania gel.     

High performance anode-supported intermediate temperature solid oxide fuel cells (IT-SOFCs) with La0.8Sr0.2Ga0.8Mg0.2O3−δ electrolyte films prepared by electrophoretic deposition

Remarkable power density was obtained for anode-supported solid oxide fuel cells (SOFCs) based on La_0.8Sr_0.2Ga_0.8Mg_0.2O_3−δ (LSGM) electrolyte films, fabricated following an original procedure that allowed avoiding undesired reactions between LSGM and electrode materials, especially Ni. Electrophoretic deposition (EPD) was used for the fabrication of 30 μm-thick electrolyte films. Anode supports were made of La_0.4Ce_0.6O_2−x (LDC). The LSGM powder was deposited by EPD on an LDC green tape-cast membrane added with carbon powder, both as pore former and substrate conductivity booster. A subsequent co-firing step at 1490 °C produced dense electrolyte films on porous LDC skeletons. Then, a La_0.8Sr_0.2Fe_0.8Co_0.2O_3−δ (LSFC) cathode was applied by slurry-coating and calcined at 1100 °C. Finally, the porous LDC layer was impregnated with molten Ni nitrate to obtain, after calcination at 900 °C, a composite NiO–LDC anode. Maximum power densities of 780, 450, 275, 175, and 100 mW/cm² at 700, 650, 600, 550, and 500 °C, respectively, were obtained using H₂ as fuel and air as oxidant, demonstrating the success of the processing strategy. As a comparison, electrolyte-supported SOFCs made of the same materials were tested, showing a maximum power density of 150 mW/cm² at 700 °C, more than 5 times smaller than the anode-supported counterpart.     

Cathodic deposition of ternary In+As+Sb alloys and formation of InAsxSb1−x

In+As+Sb alloys have been deposited onto Ni and Ti cathodes from tartaric acid solutions at pH 2. Homogeneous deposits of composition suitable for achieving InAs_xSb_1−x can be obtained from this medium. The As-to-Sb ratio can be controlled by properly selecting solution composition and deposition potential.X-ray photoelectron spectroscopy and X-ray diffraction analyses show that formation of III–V compounds occurs at room temperature. In reacts preferentially with As rather than with Sb, but crystalline phases formed at room temperature are Sb-rich. After annealing the In+As+Sb alloys at 250°C, the composition calculated from cell parameters appears similar to that measured by energy-dispersive X-ray analysis, suggesting that the entire deposit has been converted into the InAs_xSb_1−x crystalline phase.     

Polyol-mediated synthesis of Li4Ti5O12 nanoparticle and its electrochemical properties

Li₄Ti₅O₁₂ nanoparticles were precipitated from ethylene glycol solution of titanium tetra isopropoxide (Ti(O-iPr)₄) and Li₂O₂ by refluxing at 197 °C for 12 h. The obtained particles were filtered and dried at 100 °C for 12 h, and the dried powder samples were heated at 320, 500 and 800 °C for 3 h. The X-ray diffraction patterns of the obtained samples exhibited a good fit with the spinel phase. The field emission-SEM images of the dried powder sample and the samples heated at 320, 500 and 800 °C for 3 h showed a uniform spherical morphology with a particle size of 5, 8, 10 and 400 nm, respectively. According to the results of electrochemical testing, the dried powder sample and the samples heated at 320, 500, and 800 °C for 3 h showed initial capacities of 200, 310, 320, and 260 mA h/g, respectively, at a current density of 0.05 mA/cm². Nanosized (6–8 nm) particles with good crystallinity were obtained by controlling the synthesis conditions. The sample heated at 500 °C for 3 h exhibited a high capacity and an excellent rate capability over 60 cycles.     

Conventional hydrothermal process versus microwave-assisted hydrothermal synthesis of La1−xAgxMnO3+δ (x = 0, 0.2) perovskites used in methane combustion

A study on the synthesis of La_1−xAg_xMnO_3+δ (x = 0, 0.2) using a microwave process (MWhyd) has been carried out by comparing the heating time and reaction temperature with the same factor under conventional thermal process (CHhyd). Experiments have been conducted using the hydrothermal method at medium pressure (T = 200 °C, P = 20 atm) followed by a thermal treatment of the precursor at 700 °C (10 h).Structural and physico-chemical properties of the catalysts were investigated using X-ray diffraction (XRD), BET sorption, temperature-programmed reduction or desorption, mass spectrometry (TPR-MS and TPD-MS), and X-ray photoelectron spectroscopy (XPS). While CHhyd and MWhyd powder catalysts exhibited the same XRD patterns indexed as pure perovskite structure, their surface physico-chemical properties were found to be strongly influenced by the preparation method. The effect of the nature of oxygen species, their amount and mobility, evidenced by temperature programmed experiments, on the catalytic properties in methane combustion in the presence and in the absence of hydrogen sulphide has been studied. MWhyd-La_0.8Ag_0.2MnO_3+δ catalysts were found to exhibit a much better performance in methane combustion together with higher resistance to sulphur poisoning than CHhyd catalysts.     

Cobalt–silicon mixed oxide nanocomposites by modified sol–gel method

Cobalt–silicon mixed oxide materials (Co/Si=0.111, 0.250 and 0.428) were synthesised starting from Co(NO₃)₂·6H₂O and Si(OC₂H₅)₄ using a modified sol–gel method. Structural, textural and surface chemical properties were investigated by thermogravimetric/differential thermal analyses (TG/DTA), XRD, UV–vis, FT-IR spectroscopy and N₂ adsorption at −196 °C. The nature of cobalt species and their interactions with the siloxane matrix were strongly depending on both the cobalt loading and the heat treatment. All dried gels were amorphous and contained Co²⁺ ions forming both tetrahedral and octahedral complexes with the siloxane matrix. After treatment at 400 °C, the sample with lowest Co content appeared amorphous and contained only Co²⁺ tetrahedral complexes, while at higher cobalt loading Co₃O₄ was present as the only crystalline phase, besides Co²⁺ ions strongly interacting with siloxane matrix. At 850 °C, in all samples crystalline Co₂SiO₄ was formed and was the only crystallising phase for the nanocomposite with the lowest cobalt content. All materials retained high surface areas also after treatments at 600 °C and exhibited surface Lewis acidity, due to cationic sites. The presence of cobalt affected the textural properties of the siloxane matrix decreasing microporosity and increasing mesoporosity.     

A pyrolysis-GC–MS investigation of poly(vinyl phenyl ketone)

The thermal decomposition process and pyrolysis products of poly(vinyl phenyl ketone) (PVPK) were investigated by thermogravimetric analysis (TGA) and on-line pyrolysis-gas chromatography–mass spectrometry (Py-GC–MS). TGA showed a largest weight loss rate around 380 °C. Py-GC–MS was used for the qualitative analysis of the pyrolysis products at 350, 500, 600, 700 and 850 °C. The major volatile thermal decomposition product was found to be 1-phenyl-2-propenone, which dominated all other volatile species especially under the least severe pyrolysis conditions (<600 °C). At higher temperatures a much wider range of pyrolysis products was obtained. The results have been interpreted assuming that primary random chain scission reactions occur followed by typical unzipping mainly producing monomer units; detachment of the side-group occurs only under more severe pyrolysis conditions. Py-GC–MS showed to be effective in PVPK detection in ink and paint formulations.     

Formation of interfacial microstructures of Mo‐coating modified SiCf/Mo/Ti‐6Al‐4V composites

This paper addresses the role of Mo coating to modify the interface of SiC fiber reinforced Ti‐6Al‐4V composite (SiC_f/Mo/Ti‐6Al‐4V). The formation of microstructure as well as the diffusion of elements in the interface of as‐prepared and heat‐treated SiC_f/Mo/Ti‐6Al‐4V composites was investigated. The results show that the phases formed at the interfacial zone are: Mo coating∣TiC∣Mo + β‐Ti∣β‐Ti∣β‐Ti + α‐Ti_strip, ordering from fiber to matrix. Mo coating can effectively hinder the diffusion of elements between the matrix and fiber to some extent, thus it can inhibit fiber/matrix interfacial reaction and protect the fiber from damage. It is believed that the β‐Ti layer formed around the interface can improve the formability of composites. Furthermore, it indicates that Mo coating exhibits excellent thermal stability bellow 700 °C according to the heat treatment of the composites at 700 °C for up to 200 h. Copyright © 2012 John Wiley & Sons, Ltd.     

Structure and Magnetism of Pr1−xSrxFeO3−δ

Crystal structure, redox, and magnetic properties for the Pr_1−xSr_xFeO_3−δ solid-solution phase have been studied. Oxidized samples (prepared in air at 900°C) crystallize in the GdFeO₃-type structure for 0≤x≤0.80, and probably in the Sr₈Fe₈O₂₃-type (unpublished) structure for x=0.90. Reduced samples (containing virtually only Fe³⁺) crystallize as the perovskite aristotype for x=0.50 and 0.67 with randomly distributed vacancies. The Fe⁴⁺ content increases linearly in the oxidized samples up to x≈0.70, whereupon it stabilizes at around 55%. Antiferromagnetic ordering of the G type is observed for oxidized samples (0≤x≤0.90) which show decreasing Néel temperature and ordered magnetic moment with increasing x, while the Néel temperature is nearly constant at 700 K for reduced samples. Electronic transitions for iron from an average-valence state via charge-separated to disproportionated states are proposed from anomalies in magnetic susceptibility curves in the temperature ranges 500–600 K and 150–185 K.     

Synthesis of Cd/(Al+Fe) layered double hydroxides and characterization of the calcination products

Layered double hydroxides (LDHs) containing Cd(II), Al(III), and Fe(III) in the brucite-like layers with different starting Fe/Al atomic ratios and with nitrate as counteranion have been prepared following the coprecipitation method at a constant pH value of 8. An additional Cd(II),Al(III)-LDH sample interlayered with hexacyanoferrate(III) ions has been prepared by ionic exchange at pH 9. The samples have been characterized by elemental chemical analysis, powder X-ray diffraction (PXRD), and FT-IR spectroscopy. Their thermal stability has been assessed by thermogravimetric and differential thermal analyses (TG-DTA) and mass spectrometric analysis of the evolved gases. The PXRD patterns of the solids calcined at 800 °C show diffraction lines corresponding to Cd(Al)O and spinel-type materials, which precise nature (CdAl₂O₄, Cd_1−xFe_2+xO₄, or Cd_xFe_2.66O₄) depends on location and concentration of iron in the parent material or precursor.     

Electrochemical modification of Bi2S3 coatings in a nickel plating electrolyte

The electrochemical behavior of Bi₂S₃ coatings in Watts nickel plating electrolyte was investigated using the cyclic voltammetry, electrochemical quartz crystal microbalance, X-ray diffraction, and energy dispersive X-ray analysis methods. During the bismuth sulfide coating reduction in Watts background electrolyte in the potential region from −0.4 to −0.6 V, the Bi₂S₃ and Bi(III) oxygen compounds are reduced to metallic Bi, and the decrease in coating mass is related to the transfer of S²⁻ ions from the electrode surface. When the bismuth sulfide coating is reduced in Watts nickel plating electrolyte, the observed increase in coating mass in the potential region −0.1 to −0.4 V is conditioned by Ni²⁺ ions reduction before the bulk deposition of Ni, initiated by Bi₂S₃. In this potential region, the reduction of Bi(III) oxygen compounds can occur. After the treatment of as-deposited bismuth sulfide coating in nickel plating electrolyte at E = −0.3 V, the sheet resistance of the layer decreases from 10¹³ to 500–700 Ω cm. A metal-rich mixed sulfide Ni₃Bi₂S₂–parkerite is obtained when as-deposited bismuth sulfide coating is treated in Watts nickel plating electrolyte at a potential close to the equilibrium potential of the Ni/Ni²⁺ system and then annealed at temperatures higher than 120 °C.     

Synthesis, crystal structure and magnetic properties of oxo-bridged binuclear iron(III) complex [Fe(phen)2PhCOO]2OCl2·7H2O

An oxo-bridged binuclear iron(III) complex, [Fe(phen)₂PhCOO]₂OCl₂·7H₂O, was synthesized and the crystal structure indicated that two octahedrally coordinated iron(III) ions bridged with oxygen atoms formed a non-linear complex. The bond angle of Fe---O---Fe is 155.6°. The studies of magnetic properties showed that there was strong antiferromagnetic superexchange coupling (J = −80.8 cm⁻) between two S = 5/2 iron(III) ions.     

Crystallization Behavior of SiO2-TiO2 Ceramics Derived from Titanosiloxanes on Pyrolysis

The crystallization behavior of SiO2-TiO2 ceramics derived from titanosiloxanes was investigated in relation to the structure of the precursor and the pyrolysis temperature. The titanosiloxanes, [Si(OBut)2OTi(acac) 2O]2, [(ButO)3SiO] 2Ti (OPri)2, and [(ButO)3SiO] 3Ti(OPri), were pyrolyzed in an air atmosphere to form SiO2-TiO2 ceramics which crystallized to anatase at 600–650°C, 700–750°C, and 800–850°C, respectively. The crystallization temperature decreased with increased titanium content of the precursor. The average crystallite size of anatase increased with increased pyrolysis temperature and the titanium content. The crystallization temperature and the crystallite size for SiO2-TiO2 ceramics is controlled by the precursor structure, which may enable control of the physical properties of the ceramic materials.     

贵金属铱对氨分解用镍基催化剂的促进作用研究

用湿式浸渍法制备了不同贵金属质量分数的镍-铱双金属催化剂,以氨分解为模型反应对其催化性能进行考察.结果表明,贵金属铱的添加提高了10%Ni/γ-Al2O3的低温活性.在铱的质量分数不高于1%时,氨分解反应活性随铱质量分数的增加出现最大值(相应的Ir质量分数为0.7%),对应的10%Ni-0.7%Ir/γ-Al2O3催化剂在400 ℃时,氨分解率为43.55%,较单组分的Ni催化剂高40.0%.用H2-TPR、H2-TPD 、BET和XRD表征方法对催化剂进行了表征.结果表明,Ir与活性组分Ni之间存在协同作用.铱的添加促进了活性组分的分散、减小了镍的晶粒尺寸,且增加了催化剂活性位的数量,从而提高了催化剂的氨分解性能.     

Oxoacidic properties of some Ba-based chloride melts

Solubilities of CdO and ZnO in molten BaCl₂–KCl–NaCl (0.43:0.29:0.28) and BaCl₂–KCl (0.26:0.74) at 700°C have been determined by the potentiometric titration technique. Oxobasicity indices of these melts are estimated as 2.01 and 1.83, respectively. A correlation between oxobasicity indices and the content of most acidic cation (Ba²⁺) is shown to exist.     

Preparation of “pore-fill” type Pd–YSZ–γ-Al2O3 composite membrane supported on α-Al2O3 tube for hydrogen separation

Mesoporous YSZ–γ-Al₂O₃ membranes were coated on α-Al₂O₃ (Ø2 mm) tube by dipping the α-Al₂O₃ support tube into mixed sol consists of nano-size YSZ and bohemite particles followed by drying and calcination at 600 °C. Addition of bohemite in YSZ sol helped a good adhesion and uniform coating of the membrane film onto α-Al₂O₃ support. The quality of the mesoporous YSZ–γ-Al₂O₃ membranes was evaluated by the gas permeability experiments. The number of defects was minimized when the γ-Al₂O₃ content became more than 40%. Addition of γ-Al₂O₃ inhibited the crystal growth of YSZ, sintering shrinkage and distortion stress. Increase of calcination temperature and time results in the increase of pore size and N₂ permeance. A hydrogen perm-selective membrane was prepared by filling palladium into the nano-pores of YSZ–γ-Al₂O₃ layer by vacuum-assisted electroless plating. Crystal growth of palladium was observed by thermal annealing of the membrane at 600 °C for 40 h. The Pd–YSZ–γ-Al₂O₃ composite membrane revealed improved thermal stability allowing long-term operation at elevated temperature (>500 °C). This has been attributed to the improved fracture toughness of YSZ–γ-Al₂O₃ layer and matching of thermal expansion coefficient between palladium and YSZ. Although fracture of the membrane did not occur, decline of H₂ flux was observed when the membrane was exposed in 600 °C. This has been attributed to the agglomeration of palladium particles by crystal growth and dense packing into the pore networks of YSZ–γ-Al₂O₃ by elevation of temperature.