温度变化对热压电介质裂纹尖端力电损伤的影响分析

由连续介质损伤力学的基本理论出发,引入力电损伤变量并建立了一个热压电介质断裂的损伤本构模型．再由虚功原理导出了求解这类含损伤的关于热力电耦合问题的有限元方程．通过数值计算,分析了温度改变对裂纹尖端力电损伤的影响规律．     

沥青混合料疲劳过程的损伤力学分析

采用损伤力学方法研究沥青混合料的疲劳失效问题。针对悬壁梁弯曲疲劳试件,推导出疲劳过程中应力场、损伤场和疲劳裂纹形成寿命的工程封闭公式。根据沥青混合料特点,提出一种模拟疲劳裂纹扩展的特征单元失效模式,从而将疲劳裂纹形成与扩展两个阶段统一用损伤力学理论进行描述和分析。本文对沥青混合料试件的疲劳裂纹形成寿命与扩展寿命分段进行了预测,还对疲劳过程中刚度衰减及位移幅值的演化过程进行了数值模拟计算。理论预期与实验结果吻合良好。     

A penny-shaped crack in a transversely isotropic piezoelectric layer

In this paper, we develop a model to treat penny-shaped crack configuration in a piezoelectric layer of finite thickness. The piezoelectric layer is subjected to axially symmetric mechanical and electrical loads. Hankel transform technique is used to reduce the problem to the solution of a system of integral equations. A numerical solution for the crack tip fields is obtained for different crack radius and crack position.     

Ⅱ型动态扩展裂纹尖端的弹黏塑性渐近场

考虑材料的黏性效应建立了Ⅱ型动态扩展裂纹尖端的力学模型,假设黏性系数与塑性等效应变率的幂次成反比,通过分析使尖端场的弹、黏、塑性得到合理匹配,并给出边界条件作为扩展裂纹定解的补充条件,对理想塑性材料中平面应变扩展裂纹尖端场进行了弹黏塑性渐近分析,得到了不含间断的连续解,并讨论了Ⅱ型裂纹数值解的性质随各参数的变化规律.分析表明应力和应变均具有幂奇异性,对于Ⅱ型裂纹,裂尖场不含弹性卸载区.引入Airy应力函数,求得了Ⅱ型准静态裂纹尖端场的控制方程,并进行了数值分析,给出了裂纹尖端的应力应变场.当裂纹扩展速度(M→0)趋于零时,动态解趋于准静态解,表明准静态解是动态解的特殊形式.     

微小缺口/孔洞的激光衍射无损检测

基于裂纹和孔洞的小尺寸特征,提出了微小缺口/孔洞的激光衍射无损探测技术,给出了解析表达式.通过这一技术,对单向拉伸试件中所含单边缺口和中心孔洞在外载作用下的演化过程进行了实时原位检测,获得了缺口/孔洞孔径随载荷的变化曲线及模拟裂纹时裂纹的张开位移、裂纹开裂长度及应力强度因子等一系列断裂参数.     

APPLICATION OF THE DIGITAL MOIRE METHOD IN FRACTURE ANALYSIS OF A CRACKED RUBBER SHEET

This paper deals with the mode I crack problem of a cracked rubber sheet under plane stress condition using the delicate digital moire technique. Through the four step phase-shifting method of automated fringe analysis, the displacement fields in the Cartesian coordinate system are given. By the coordinate-transform equation, the radial and circular displacement distributions in the polar coordinate system are obtained. The displacement isoline distributions and displacement vector distributions near the crack tip are discussed. The strain isoline distributions near the crack tip are also analyzed in this paper. Finally, the distribution rules for the mechanical fields near the crack tip are discussed with the sector division method.     

基于局域分析的疲劳短裂纹群体演化随机模型

采用局域裂纹数密度描述金属材料中不同局部区域的疲劳短裂纹群体损伤的发展情况通过考虑在不同局域存在的材料性质的随机涨落及局部损伤对损伤总量发展的影响，建立了局域裂纹数密度演化随机方程对方程数值求解从而模拟了材料的疲劳短裂纹损伤过程结果显示出主裂纹出现的随机性，并讨论了裂纹总数与最大裂纹尺度在统计意义上的演化特征     

力场-化学场耦合作用对含裂纹固体电解质力学行为的研究

为了研究力场-化学场耦合作用下的含裂纹电解质的断裂问题,本文构造了耦合情况下力场和浓度场的本构关系,并由这些本构关系建立了力场-化学场耦合问题的有限元方程。通过具体的算例,进一步探讨了裂纹尖端应力场和氧空位浓度分布的耦合作用对GDC(氧化钆掺杂的氧化铈)力学行为的影响,发现在耦合作用下,裂尖应力场对氧空位的分布有明显的诱导作用。     

INTERACTION OF A DISLOCATION DIPOLE WITH A MODE III INTERFACE CRACK

Interaction between a screw dislocation dipole and a mode III interface crack is investigated. By using the complex variable method, the closed form solutions for complex potentials are obtained when a screw dislocation dipole lies inside a medium. The stress fields and the stress intensity factors at the tip of the interface crack produced by the screw dislocation dipole are given. The influence of the orientation, the dipole arm and the location of the screw dislocation dipole as well as the material mismatch on the stress intensity factors is discussed. The image force and the image torque acting on the screw dislocation dipole center are also calculated. The mechanical equilibrium position of the screw dislocation dipole is examined for various material property combinations and crack geometries. The results indicate that the shielding or anti-shielding effect on the stress intensity factor increases abruptly when the dislocation dipole approaches the tip of the crack. Additionally, the disturbation of the interface crack on the motion of the dislocation dipole is also significant.     

Pre-kinking of a moving crack in a magnetoelectroelastic material under in-plane loading

A constant moving crack in a magnetoelectroelastic material under in-plane mechanical, electric and magnetic loading is studied for impermeable crack surface boundary conditions. Fourier transform is employed to reduce the mixed boundary value problem of the crack to dual integral equations, which are solved exactly. Steady-state asymptotic fields near the crack tip are obtained in closed form and the corresponding field intensity factors are expressed explicitly. The crack speed influences the singular field distribution around the crack tip and the effects of electric and magnetic loading on the crack tip fields are discussed. The crack kinking phenomena is investigated using the maximum hoop stress intensity factor criterion. The magnitude of the maximum hoop stress intensity factor tends to increase as the crack speed increases.     

Higher order fields for damaged nonlinear antiplane shear notch, crack and inclusion problems

Damaged nonlinear antiplane shear problems with a variety of singularities are studied analytically. A deformation plasticity theory coupled with damage is employed in analysis. The effect of microscopic damage is considered in terms of continuum damage mechanics approach. An exact solution for the general damaged nonlinear singular antiplane shear problem is derived in the stress plane by means of a hodograph transformation, then corresponding higher order asymptotic solutions are obtained by reversing the stress plane solution to the physical plane. As example, traction free sharp notch and crack, rigid sharp wedge and flat inclusion, and mixed boundary sharp notch problems are investigated, respectively. Consequently, higher order fields are obtained, in which analytical expressions of the dominant and second order singularity exponents and angular distribution functions of the near tip fields are derived. Effects of the damage and hardening exponents of materials and the geometric angle of notch/wedge on the near tip quantities are discussed in detail. It is found that damage leads to a weaker dominant singularity of stress, but to little stronger singularities of the dominant and second order terms of strain compared to that for undamaged material. It is also seen that damage has important effect on the angular distribution functions of the near tip stress and strain fields. As special cases, higher order analytical solutions of the crack and rigid flat inclusion tip fields are obtained, respectively, by reducing the notch/wedge tip solutions. Effects of damage and hardening exponents on the dominant and second order terms in the solutions of the crack and inclusion tip fields are discussed.     

A cyclic steady-state method for fatigue crack propagation: Evaluation of plasticity-induced crack closure in 3D

The numerical study of plasticity-induced crack closure using the node-release technique presents many difficulties widely studied in literature. For instance various rules, proposed for overcoming mesh sensitivity, are challenged by more recent studies. This paper intends to propose and evaluate a numerical method for the investigation of crack propagation under fatigue loading, and particularly for the assessment of plasticity-induced crack closure in three-dimension. The method is an extension of the “steady-state method” to cyclic loadings. The steady-state method allows a direct computation (on a fixed mesh, without releasing nodes) of stress and strain fields around the crack tip and in the wake for a steady crack growth. The method is extended to simulate crack propagation under fatigue loading. Therefore it constitutes a valuable numerical tool for gaining insight into the physics of crack propagation, as it provides accurate mechanical fields around the crack tip and their relation with crack growth rate, various loading modes and parameters. The proposed method is also compared with the classical node-release technique. A very good agreement between the two methods is found. However the steady-state method needs much less mesh refinement and computational time. Following an analysis of some features of the fatigue crack, a discussion on a crack closure criterion is opened, and a reliable criterion for the determination of local crack closure is proposed.     

Real-time Detection and Analysis of Damage in High-performance Concrete under Cyclic Bending

In order to quantitatively evaluate the damage level in high-performance concrete (HPC) with pozzolanic minerals under constant amplitude cyclic loads, three methods for real-time damage detection are employed in the present work, i.e., dynamic modulus instrument, real-time strain collector, and digital speckle correlative method (DSCM). Six mechanical parameters at different numbers of loading cycles are real-time captured by these three methods. For a maximum applied fatigue stress equal to 70% of the static flexural strength, a cohesive crack is detected on the specimen surface by the DSCM system from 10% of concrete fatigue life. The nucleation and propagation of the cohesive crack is reflected by the change of the strain concentration zone in 2-dimensional strain fields. The experimental results show that the admixtures of Class F Fly Ash (FA) and S95 Ground Granulated Blast-furnace Slag (GGBS) in high proportions increase the strain and cohesive-crack opening displacement as well as remarkably improve the fatigue performance of HPC.     

Asymptotic mechanical fields at the tip of a mode I crack in rubber-like solids

Asymptotic analyses of the mechanical fields in front of stationary and propagating cracks facilitate the understanding of the mechanical and physical state in front of crack tips, and they enable prediction of crack growth and failure. Furthermore, efficient modelling of arbitrary crack growth by use of XFEM (extended finite element method) requires accurate knowledge of the asymptotic crack tip fields. In the present work, we perform an asymptotic analysis of the mechanical fields in the vicinity of a propagating mode I crack in rubber. Plane deformation is assumed, and the material model is based on the Langevin function, which accounts for the finite extensibility of polymer chains. The Langevin function is approximated by a polynomial, and only the term of the highest order contributes to the asymptotic solution. The crack is predicted to adopt a wedge-like shape, i.e. the crack faces will be straight lines. The angle of the wedge and the order of the stress singularity depend on the hardening of the strain energy function. The present analysis shows that in materials with a significant hardening, the inertia term in the equations of motion becomes negligible in the asymptotic analysis. Hence, there is no upper theoretical limit to the crack speed.     

正交异性材料平面裂纹尖端应力场

根据正交各向异性材料力学性能确定出了用应力函数表示的弹性力学基本方程,利用坐标变换和复变函数方法求解了正交异性材料平面裂纹体的应力边值问题。借鉴一般断裂力学解法构造了I型和II型裂纹问题的应力函数,推导出了正交各向异性板裂纹尖端区的奇异应力场。通过数值计算说明了裂纹尖端应力表达式的正确性,验证了裂尖前沿应力变化规律,即σx与材料特征参数h2成正比,而σy和τxy不随材料特性变化。     

一种随机裂纹结构的裂纹扩展路径分析方法

裂纹结构中存在大量不确定性因素,如裂纹长度、材料性质、外部载荷等,裂纹扩展路径的不确定性分析对研究随机裂纹结构损伤和断裂的力学特性并预测其性能及可靠性具有重要意义。本文提出了一种适应于混合载荷模式下随机裂纹结构的裂纹扩展路径分析方法。该方法考虑了裂纹长度、材料性质和外部载荷等的随机性,并通过蒙特卡洛方法对随机参数空间进行采样。采用比例边界有限元方法计算结构应力强度因子,进而模拟单次裂纹扩展路径。在此基础上,通过概率分析方法获得随机裂纹结构中裂纹扩展路径的统计特性。最后给出了两个数值算例验证了本文方法的有效性。     

Fracture mechanics for a mode III crack in a magnetoelectroelastic solid

In this paper, we developed a Stroh-type formalism for anti-plane deformation and then investigated the fracture mechanics for an elliptical cavity in a magnetoelectroelastic solid under remotely uniform in-plane electromagnetic and/or anti-plane mechanical loading, which allowed us to take the electromagnetic field inside the cavity into account. Reducing the cavity into a crack, we had explicit solutions in closed forms for a mode III crack, which included the extreme cases for an impermeable crack and a permeable crack. The results were illustrated with plots, showing that in the absence of mechanical loads, an applied electric or magnetic field, positive or negative, always tended to close the crack. On the other hand, in the presence of a mechanical load, a negative electric or magnetic field retarded crack growth, while a positive field could either enhance or retard crack propagation, depending on the strengths of the applied electric/magnetic fields and the level of the mechanical load as well. In other words, the effect of electric/magnetic fields on the fracture behavior is mechanical load-dependent.     

Elastic-viscoplastic field at mixed-mode interface crack-tip under compression and shear

For a compression-shear mixed mode interface crack, it is difficult to solve the stress and strain fields considering the material viscosity, the crack-tip singularity, the frictional effect, and the mixed loading level. In this paper, a mechanical model of the dynamic propagation interface crack for the compression-shear mixed mode is proposed using an elastic-viscoplastic constitutive model. The governing equations of propagation crack interface at the crack-tip are given. The numerical analysis is performed for the interface crack of the compression-shear mixed mode by introducing a displacement function and some boundary conditions. The distributed regularities of stress field of the interface crack-tip are discussed with several special parameters. The final results show that the viscosity effect and the frictional contact effect on the crack surface and the mixed-load parameter are important factors in studying the mixed mode interface crack- tip fields. These fields are controlled by the viscosity coefficient, the Mach number, and the singularity exponent.     

Dynamic crack tip fields and dynamic crack propagation characteristics of anisotropic material

Based on mechanics of anisotropic material, the dynamic crack propagation problem of I/II mixed mode crack in an infinite anisotropic body is investigated. Expressions of dynamic stress intensity factors for modes I and II crack are obtained. Components of dynamic stress and dynamic displacements around the crack tip are derived. The strain energy density theory is used to predict the dynamic crack extension angle. The critical strain energy density is determined by the strength parameters of anisotropic materials. The obtained dynamic crack tip fields are unified and applicable to the analysis of the crack tip fields of anisotropic material, orthotropic material and isotropic material under dynamic or static load. The obtained results show Crack propagation characteristics are represented by the mechanical properties of anisotropic material, i.e., crack propagation velocity M and fiber direction α. In particular, the fiber direction α and the crack propagation velocity M give greater influence on the variations of the stress fields and displacement fields. Fracture angle is found to depend not only on the crack propagation but also on the anisotropic character of the material.     

不同地应力条件下切缝药包爆破的数值模拟

针对切缝药包定向爆破的特点,考虑岩石介质非均匀性的基础上,把岩石爆破视为爆炸应力波动态作用和爆生气体压力准静态作用的过程,基于损伤力学理论建立岩石爆破的力学模型,并对不同地应力条件下切缝药包爆破的裂纹演化规律进行数值模拟,分析不同地应力条件对切缝药包爆破效果的影响。模拟结果表明:采用切缝药包爆破时,裂纹主要萌生于切缝周边,沿切缝方向扩展,切缝对定向裂纹的控制作用明显;当考虑地应力作用,且最大地应力方向与切缝方向垂直时,不利于定向裂纹的扩展;最大地应力方向与切缝方向平行时,有利于定向裂纹的扩展。裂纹的扩展方向受控于切缝角度和最大地应力方向这2个条件,裂纹扩展规模则受到地应力的限制。