Efficient fabrication and enhanced photocatalytic activities of 3D-ordered films of titania hollow spheres

Facile and effective approaches were developed to fabricate 3D-ordered films of titania hollow spheres with different sphere diameters. The shell thickness of the sphere was adjusted in the range of 20-40 nm by changing the casting cycle of the titania precursor. The photonic stop band was observed for the 3D-ordered film and was tunable by the sphere diameter and the shell thickness. The stop band shifted from 930 to 547 nm. Crystal violet dye adsorbed on the film exhibited more than two times higher absorbance than that on a reference film of a flat titania layer, probably due to the red edge effect of the stop band and/or to the multiple scattering effect. The enhanced absorbance led to more efficient photodegradation of the dye under visible light and under solar light irradiation. A maximum photocatalytic enhancement of 22% is achieved. Finally, the influence of TiO2 morphology on photocatalytic activity was discussed. Compared with flat titania films, the existence of ordered macropores in titania spheres causes the stop band and a longer optical path due to multiple scattering. Both the red edge of the stop band and multiple scattering effects enhance the absorption of the dye, which results in the photocatalytic enhancement.     

Fabrication of sub-micrometer-sized jingle bell-shaped hollow spheres from multilayered core-shell particles

Jingle bell-shaped hollow spheres were fabricated starting from multilayered particles composed of a silica core, a polystyrene inner shell, and a titania outer shell. Composite particles of silica core-polystyrene shell, synthesized by coating a 339-nm-sized silica core with a polystyrene shell of thickness 238 nm in emulsion polymerization, were used as core particles for a succeeding titania-coating. A sol-gel method was employed to form the titania outer shell with a thickness of 37 nm. The inner polystyrene shell in the multilayered particles was removed by immersing them in tetrahydrofuran. These successive procedures could produce jingle bell-shaped hollow spheres that contained a silica core in the titania shell.     

金属Al薄膜基微池强制沉积胶体光子晶体的制备

强制沉积法是一种利用自组装原理快速沉积胶体晶体有序阵列的模板方法. 我们利用微机械刻划法加工金属Al薄膜, Al膜厚控制微粒粒径和聚醚砜膜厚控制层数, 成功地制备了用于强制沉积光子晶体的微池装置. 为了检验该微池装置的有效性, 我们分别测试了不同粒径(224, 245和283 nm)单分散聚苯乙烯微球的沉积效果, 并且对其中一种微球(283 nm)进行了不同温度的烘干处理, 检验了烘干温度对该样品表面形貌和光子带隙中心波长的影响. 实验结果表明, 该光子晶体呈面心立方结构, 内部晶格完整, 缺陷较少, 带隙中心波长的实验值与计算值符合得较好. 此外, 烘干处理可以使构成光子晶体的微球发生微观变化, 并导致光子带隙中心波长的蓝移.     

High-speed fabrication of patterned colloidal photonic structures in centrifugal microfluidic chips

In this paper, we report a rapid and facile method for fabricating colloidal photonic crystals inside microchannels of radially symmetric microfluidic chips which were made using soft-lithography. As the suspension of monodisperse silica or polystyrene latex spheres was driven to flow through the channels under the action of centrifugal force, the colloidal spheres were quickly assembled into face centered cubic arrangement which had a few photonic stop bands. The soft-microfluidic channels and cells confined the colloidal crystals into designed patterns. The optical reflectance was modulated by the refractive-index mismatch between the colloidal particles and the solvent in the interstices between the particles. Therefore, the present microfluidic chips with built-in colloidal photonic crystals can be used as in-situ optofluidic microsensors for high throughput screening or light filters in integrated adaptive optical devices.     

胶体光子晶体的平面介电常数缺陷

为引入特殊的光学性质,通常需要在三维光子晶体中人为可控地引入缺陷.通过改变局部结构单元的尺寸或介电常数,相应地引入给体或受体掺杂,带来不同的缺陷态.以前文献报道的向胶体光子晶体中引入缺陷,常会因为同时引入尺寸和介电常数掺杂,给掺杂性质的界定带来困难.本文中,我们结合对流自组装法和L-B膜法,在实心二氧化硅微球组成的三维光子晶体内引入尺寸相同的二氧化硅空心球(与实心球相比具有不同折光率)组成的单层平面缺陷,或者在空心球晶体内引入实心球缺陷层,构成实心-空心-实心或空心-实心-空心的三明治结构,在不破坏整体晶格的同时,在三维胶体光子晶体中引入单一的平面介电常数缺陷.     

Close-packed colloidal crystalline arrays composed of silica spheres coated with titania

Titania coated monodisperse silica spheres have been synthesized and fabricated as a close-packed colloidal crystalline array. We have demonstrated that the coated colloidal sphere can be used to control the peak position of the optical stop band through variation of the coating thickness. The titania coated silica spheres were prepared by the layer-by-layer assembly coating process, which reciprocally laminates the cationic polyelectrolyte and the anionic titania nanosheets on a monodisperse silica spheres, and were sintered to change the titania nanosheets to anatase. The Bragg diffraction peak of the colloidal crystalline array shifted to the long wavelength region with an increase of thickness of the titania layer. Angle-resolved reflection spectra measurements clarified that the red shift was caused by increasing of the refractive index with increase of the thickness of the layer. The current work suggests new possibilities for the creation of advanced colloidal crystalline arrays with tunable optical properties from tailored colloidal spheres.     

Preparation of Waterproof Organometal Halide Perovskite Photonic Crystal Beads

Herein, we report on an innovative method for the preparation of a series of organometal halide perovskite (OHP) photonic crystal beads with pronounced and tunable photonic stop bands by using self-assembled polystyrene spheres as a mold. After infiltration of the mold with OHP precursor solution and slow drying, the OHPs crystallized in the voids of the polystyrene arrays. By controlling the diameter of the polystyrene spheres, the photonic stop band of the OHPs could be precisely tuned. The overlap between the photonic stop band of the beads and the band gap of the OHPs enhances the light harvesting of the perovskite because of the slow photon effect, which arises from the photonic crystal beads. Moreover, the stability of the composite was greatly enhanced by coating with the transparent polymer PDMS without blocking the light propagation. The coated OHP photonic beads kept their composition even after having been in contact with water for 24 h.     

Fabrication of spherical colloidal crystals using electrospray

We demonstrated the use of electrohydrodynamic atomization to prepare uniform-sized emulsion droplets in which equal spheres of silica or polystyrene were dispersed. The size of the emulsion droplets was easily controlled by the electric field strength and the flow rate, independently of the diameter of the nozzles. During the evaporation of solvent in the droplets, spherical colloidal crystals were formed by self-assembly of the monodisperse colloidal spheres. The diameter of the spherical colloidal crystals was in the range of 10-40 microm. Depending on the stability of colloidal particles, the morphology of the self-assembled structure was varied. In particular, silica spheres in ethanol droplets were self-assembled into compactly packed silica colloidal crystals in spherical shapes, whereas polystyrene latex spheres in toluene droplets self-assembled into spherical colloidal crystal shells with hollow cores. The silica colloidal assemblies reflected diffraction colors according to the three-dimensionally ordered arrangement of silica spheres.     

Sonochemical preparation of hollow nanospheres and hollow nanocrystals

Ceramic hollow spheres of MoS2 and MoO3 were obtained by sonochemical synthesis of MoS2 and MoO3 templated on silica nanoparticles (diameters 50-500 nm) followed by acid etching to remove the silica core. The resulting hollow materials have been characterized by elemental analysis, XPS, SEM, TEM, optical absorption, and hydrodesulfurization (HDS) studies. The TEM studies on the hollow ceramic materials indicate the formation of dispersed free spheres with a hollow core. The hollow materials obtained from thermally treated MoS2/SiO2 (450-700 degrees C) show the formation of layered MoS2 (lattice fringes approximately 6.2 A) with a wall thickness of 6-8 layers. The MoS2 hollow spheres are extremely active catalysts for the HDS of thiophene. Hollow spheres of MoO3 are prepared in a similar fashion. Surprisingly, upon heating, hollow crystals of MoO3 with sharp-edged truncated cubes containing inner voids are formed from the initial spheres.     

Three-dimensional colloidal crystals with a well-defined architecture

Monodisperse silica spheres with diameters of 220-1100 nm were prepared by hydrolysis of tetraethyl orthosilicate (TEOS) in an alcoholic medium in the presence of water and ammonia. By grafting vinyl or amino groups onto silica surfaces using the coupling agents allyltrimethoxysilane and aminopropyltriethoxysilane, respectively, amphiphilic silica spheres were obtained and could be organized to form a stable Langmuir film at the air-water interface. The controlled transfer of this monolayer of particles onto a solid substrate gave us the ability to build three-dimensional regular crystals with a well-defined thickness and organization. These colloidal crystals diffract light in the UV, the visible, and the near-infrared (NIR) spectral regions, depending on the size of the silica spheres and according to Bragg's law. The depth of the photonic stop band can be tuned by varying the number of deposited layers of particles. By using successive depositions, we could prepare multilayered films with silica spheres of different sizes. The thickness of each slab in the binary crystals can be tuned at the layer level, while the crystalline order of each layer is well preserved.     

Synthesis of micron-sized hollow silica spheres with a novel mesoporous shell of MCF

Micron-sized hollow silica spheres whose shells are made up of mesocellular silica foams(MCFs) have been synthesized by one-pot sol-gel method in benzene/water/P123 emulsion.The material is characterized with SEM,TEM,BET and ~(29)Si MAS NMR. The results show that the MCFs of the unique shell of hollow silica spheres were connected by large windows with a narrow distribution of～10 nm in diameter,the inner space of the hollow sphere is accessible.And the formation mechanism of the hollow silica spheres is ...     

Preparation of hollow silica microspheres with controlled shell thickness in supercritical fluids

This article presents a novel route to prepare hollow silica microspheres with well-defined wall thickness by using cross-linked polystyrene (PS) microspheres as templates with the assistance of supercritical carbon dioxide (SC-CO₂). In this approach, the cross-linked PS templates can be firstly prepared via emulsifier-free polymerization method by using ethylene glycol dimethacrylate or divinylbenzene as cross-linkers. Then, the silica shell from the sol–gel process of tetraethyl orthosilicate (TEOS) which was penetrated into the PS template with the assistance of SC-CO₂ was obtained. Finally, the hollow silica spheres were generated after calcinations at 600 °C for 4 h. The shell thickness of the hollow silica spheres could be finely tuned not only by adjusting the TEOS/PS ratio, which is the most frequently used method, but also by changing the pressure and aging time of the SC-CO₂ treatment. Fourier transform infrared spectroscopy, transmission electron microscopy, and scanning electron microscope were used to characterize these hollow silica spheres.     

Effects of liquid bridge between colloidal spheres and evaporation temperature on fabrication of colloidal multilayers

For the application of colloidal crystal films as "photonic band gap" materials, their domain size and thickness are significant. The substrate withdrawing speed, the colloidal suspension volume fraction, and the colloidal suspension temperature have been studied for the domain size and thickness controls of colloidal crystals in this study. Stable dispersions of monodispersed polystyrene spheres with a diameter of 245 nm were synthesized according to a general emulsion polymerization for colloidal crystal films. By experimental results and the theoretical relationship between the number of layers and other parameters, we could know that the water bridge between colloidal spheres (which is formed by capillary force) influences the number of colloidal crystal layers significantly.     

Fabrication of hollow titania microspheres with tailored shell thickness

Submicron hollow spheres are an interesting class of materials that receive significant attention nowadays. Closed and mechanically robust homogeneous hollow titania microspheres with as much shell thickness as 130 nm were fabricated by coating polystyrene beads with titania nanoparticles using sol–gel chemistry and subsequently removing the core either via heating or a chemical dissolution process. The thickness of the titania shell deposited on polystyrene core was finely tuned between 100 and 130 nm by varying the concentration of titania precursor, i.e., Ti(OEt)₄ salt from 0.5 to 2 mM during the coating process. The obtained hybrid core–shell particles and hollow microspheres were characterized by scanning electron microscopy, transmission electron microscopy, infrared spectroscopy, X-ray diffraction, and thermo-gravimetric analysis. The approach employed is well suited to the preparation of titania-coated polystyrene hybrid particles and hollow titania spheres, which can find their applications as novel building blocks with unique optical properties for fabrication of advanced materials, catalyst, and drug delivery system.     

聚苯乙烯光子晶体的制备及其在传感中的应用

以基于毛细作用的垂直沉积法将单分散的二氧化硅胶体微球自组装成光子晶体．在二氧化硅光子晶体的多孔结构里填充聚苯乙烯甲苯溶液,经甲苯挥发,通过氢氟酸处理去除二氧化硅模板,制备出精美的聚苯乙烯光子晶体．研究表明：保留了模板有序多孔结构的聚苯乙烯能被用来作为敏感膜,这使得其在基于折射率变化的传感应用中具有潜在的价值．     

Close-packed colloidal crystalline arrays composed of polystyrene latex coated with titania nanosheets

We have demonstrated that polystyrene latex coated with titania nanosheets can be fabricated into a close-packed colloidal crystalline array, and that these coated colloidal spheres can be used to control the peak position of optical stop bands through the coating. The titania-nanosheets-coated polystyrene latex was prepared by the layer-by-layer (LBL) assembly coating process, involving alternating lamination of cationic polyelectrolytes and anionic titania nanosheets on monodisperse polystyrene latex particles. The Bragg diffraction peak of the colloidal crystalline array shifted to longer wavelengths with the coating of titania nanosheets. This red shift was caused by an increase in refractive index upon coating, as revealed by angle-resolved reflection spectra measurements. The current work suggests new possibilities for the creation of advanced colloidal crystals having tunable optical properties from tailored colloidal spheres.     

Synthesis and Photoluminescence Properties of Uniform Y2O3:Eu3+ Hollow Spheres with Tunable Shell Thickness

Y2O3:Eu3+ hollow spheres were successfully prepared with melamine formaldehyde(MF) spheres as template. The MF spheres played a significant role in directing the formation of the hollow shells which are composed of numerous primary nanoparticles. Furthermore, the shell thickness of these hollow spheres could be readily tailored by adjusting the dosage of MF template. Based on the photoluminescence(PL) investigation, the red emission intensities(613 nm) of these Y2O3:Eu3+ hollow spheres are greatly influenced by their shell thickness and it was found that hollow spheres with thin shell thickness and intact hollow structures permit a better PL performance.     

All-clay photonic crystals

Hierarchically structured "all-clay" 1D and 3D inverse photonic crystals were fabricated, featuring the crystalline layered microstructure of the phyllosilicate Laponite combined with crystalline macroporosity on the submicron scale. By using simple hard-templating protocols based on monodisperse polystyrene spheres, periodic layered silicate and inverse opal architectures with photonic crystal properties are accessible, which exhibit reflectivities of the stop band in excess of 50%. The combination of intrinsic chemical functionality with structural color makes such hierarchical "all-clay" architectures potential scaffolds in color-tunable chemo-optical devices.     

Colloidal crystal films: advances in universality and perfection

For three-dimensional photonic crystals, made either by top-down microfabrication or by bottom-up self-assembly approaches, to comply with the stringent requirements of optical telecommunication applications, their degree of structural perfection and optical quality must meet an exceptionally high standard. Only with such superior quality photonic crystals can their unique optical properties be harnessed in optical devices and circuits constructed from micrometer-sized optical components. In this paper, we present a new strategy for making silica colloidal crystal films with a sufficiently high level of structural perfection and optical quality to make it competitive as a practical route to photonic crystal optical components. The attainment of this goal takes due cognizance of three key synergistic factors in the film formation process. The first recognizes the necessity to prepare high-quality silica spheres, which are highly monodisperse, with a polydispersity index significantly better than 2%, and the second recognizes that the population of spheres must be devoid of even the smallest fraction of substantially smaller or larger spheres or sphere doublets. The latter turns out to have a minimal effect on the polydispersity index, and yet a major detrimental effect on the overall structural order of the film. The third concerns the film-forming method itself, which necessitated the development of a novel process founded upon isothermal heating evaporation-induced self-assembly (IHEISA) of spheres on a planar substrate. This new method has several advantages over previously reported ones. It is able to deposit very high-quality silica colloidal crystal film rapidly over large areas, with a controlled thickness and without any restrictions on sphere sizes.     

Polyaniline/Au composite hollow spheres: synthesis, characterization, and application to the detection of dopamine

Polyaniline (PANI)/Au composite hollow spheres were successfully synthesized using polystyrene/sulfonated polystyrene core/shell gel particle templates. The PANI shell thickness and the number of Au nanoparticles decorating the PANI could be controlled effectively by adjusting the experimental conditions. The morphology, composition, and optical properties of the resulting products were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, thermogravimetric analysis, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and ultraviolet-visible absorption spectra. It was found that the electrical conductivity of the PANI/Au composite hollow spheres was more than 3 times higher than that of the pure PANI hollow spheres. Furthermore, PANI/Au composites were immobilized on the surface of a glassy carbon electrode (GCE) and applied to construct a sensor. The obtained PANI/Au-modified GCEs showed one pair of redox peaks and high catalytic activity for the oxidation of dopamine. The possible formation mechanism of the PANI/Au composite hollow spheres was also discussed.