载药聚甲基丙烯酸-2-羟乙酯水凝胶膜的制备及性能

选择(NH4)2S2O8为引发剂,N-N′-亚甲基双丙烯酰胺(MBA)为交联剂,十二烷基硫酸钠(SDS)为制孔剂,通过改变水凝胶膜的溶剂与单体的配比、交联剂和制孔剂的量等制备出不同性质的水凝胶膜,运用电镜扫描、含水率、电子拉力机等表征不同水凝胶膜的性能.本研究尝试将硫酸新霉素药物作为载入药物导入水凝胶中,进行载药和缓释能力测试.实验结果表明,当单体甲基丙烯酸羟乙酯与水的比例为1∶3,引发剂过硫酸铵含量为单体1.0%(w/V),SDS为4.0%(w/V),MBA为4.0%(w/V)时,水凝胶的含水率为42.84%,拉伸强度为0.32MPa,药物缓释累积达峰时间为8.17h,综合性能较佳.     

双连续相微乳液辐射聚合制备多孔材料的研究

利用6 0 Co γ射线在室温下辐照双连续相微乳液体系以制备多孔聚合物材料 ,试图在控制多孔材料的微孔结构形态和减少微乳液聚合过程中的相分离方面做一些探索 .通过电导率的测量分析微乳液的结构类型 ,并确定微乳液的双连续相区域范围 .微乳液聚合后所得的样品的孔结构和聚合前的微乳液结构类型有关 ,扫描电镜和热重分析的结果表明双连续相微乳液在聚合时容易发生相分离 ,未必能够得到开孔结构的聚合物 .但适当控制聚合前微乳液的组成 ,如选择合适的水油比例、交联剂的用量和加入一些功能性单体 (如甲基丙烯酸或丙烯酸钠 ) ,可以有效地抑制相分离 ,调节所得聚合物的结构形态 .     

丙烯酸酯类吸油树脂的合成与性能研究

以丙烯酸酯、甲基丙烯酸酯为主要单体,二丙烯酸丁二醇酯为交联剂,过氧化二苯甲酰为引发剂,采用悬浮聚合方法,合成聚丙烯酸酯类高吸油树脂.研究了分散剂、引发剂、交联剂用量及单体配比等因素对树脂吸油性能的影响.结果表明,分散剂用量为单体质量的0.12%,引发剂用量为1.0%,交联剂用量为1.5%时树脂的吸油能力最佳,吸甲苯倍率可达15倍,吸汽油倍率可达10倍,吸机油倍率可达近9倍.     

淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂的制备

以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺为交联剂,淀粉与丙烯酸/醋酸乙烯酯混合单体通过接枝共聚,制备了吸水及耐盐性能均较好的淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂(CGAV)。最佳工艺条件为:淀粉10.0 g,m(混合单体)∶m(淀粉)=4∶1,w(引发剂)=0.3%,w(交联剂)=0.05%,于45℃反应2h~3 h。在最佳工艺条件下制得的CGAV吸去离子水率760 g.g-1,吸0.9%NaC l水溶液率68 g.g-1。     

不完全相反转乳化过程分散相水滴形态发展研究

相反转乳化技术是制备高分子树脂水基分散体系的新方法[1～4].相反转指多组分体系(如油/水/乳化剂)中的连续相在一定条件下相互转化的过程,如在油/水/乳化剂体系中,其连续相由水相向油相(或从油相变为水相)的转变.在连续相转变区,体系的界面张力最低,因而分散相的尺寸最小.同理,可利用相反转技术直接将高分子树脂乳化为尺寸很小的水基微粒,即制备高分子树脂的水基分散体系.由于高分子树脂的粘弹性及相反转过程的复杂性,对高分子树脂的相反转乳化过程的机理研究较少.杨振忠[5]等通过调节高分子非离子型乳化剂浓度,可以有效地控制相反转完善程…     

石蜡或聚丁二烯填充型高吸油树脂的合成及其性能比较

以过氧化二苯甲酰 (BPO)为引发剂、二甲基丙烯酸乙二酯 (EGDMA)为化学交联剂、甲基丙烯酸十二酯 (DMA)和苯乙烯 (St)为单体、石蜡 (Paraffin)或聚丁二烯 (PB)为填充剂 ,用悬浮聚合法合成了填充型高吸油树脂 .研究了单体配比、填充剂用量以及化学交联度对树脂吸油性能及凝胶分率的影响 .对石蜡和PB填充的高吸油树脂进行比较 ,发现PB填充的高吸油树脂中存在物理交联 ,而石蜡填充的树脂中不含物理交联 ;PB填充的高吸油树脂随PB用量的增加 ,吸油倍率提高 ,凝胶分率上升 ,脱油速率增大 ;而石蜡填充的树脂随石蜡用量的增加 ,吸油倍率提高 ,但凝胶分率和脱油速率变化不大     

甲基丙烯酸正丁酯正相微乳液可控/“活性”光聚合动力学研究

以末端含溴原子的光引发剂2-溴异丁酰氧基-2-甲基-1-苯基甲酮(HMPP-Br)为引发剂,2,2,6,6-四甲基哌啶-1-氧自由基(TEMPO)和2,2,6,6-四甲基哌啶醇(TMP)为调控剂,采用光聚合方法研究了甲基丙烯酸正丁酯(n-BMA)/十二烷基硫酸钠(SDS)/水/正丁醇 O/W型正相微乳液体系的光聚合反应动力学.结果表明,改性后的引发剂具有一定的引发活性,且聚合微乳液体系较稳定,聚合反应获得了良好的ln[M]₀/[M]与时间、数均分子量与转化率之间的线性动力学关系,制备了分子量分布较窄的Poly(n-BMA)均聚物.     

改性高吸油性树脂的合成

将造成环境“白色污染”的发泡聚苯乙烯添加到由丙烯酸2-乙基已酯为单体的聚合体系中,从而合成新型的高吸油性树脂。考察了发泡聚苯乙烯的添加量、交联剂和引发剂等因素对树酯吸油性能的影响,所得树脂可吸苯22g/g,吸煤油13.5/g。     

硅丙乳液的合成工艺研究

采用半连续种子乳液聚合工艺,以乙烯基三乙氧基硅烷(VTS)为改性剂、十二烷基硫酸钠(SDS)和烷基酚聚氧乙烯醚(OP-1O)为复合乳化体系,在引发剂过硫酸铵(APS)的作用下合成稳定的硅丙乳液.利用红外光谱(FTIR)和扫描电镜(SEM)对涂膜进行了表征.结果表明:单体转化率随乳化剂用量、引发剂用量、有机硅用量、聚合温...     

光致变色含氟丙烯酸酯涂层的制备及性能

选取十二烷基硫酸钠(SDS),辛基苯基聚氧乙烯醚(OP-10)为复合乳化剂,过硫酸钾(KPS)为引发剂,将2-(全氟己基)乙基甲基丙烯酸酯(PFM)与丙烯酸酯类单体采用预乳化-半连续种子乳液聚合法进行乳液共聚,再将羟基螺吡喃(SPOH)与乳液进行物理共混,制得光致变色含氟丙烯酸酯乳液。 通过多种表征手段研究丙烯酸正丁酯(n-BA)和甲基丙烯酸甲酯(MMA)软硬单体的质量比,SPOH的用量对聚合反应和乳胶膜性能的影响。 结果表明,加入含氟单体后乳胶膜与水、油的接触角提高,热稳定性提高;加入SPOH的质量分数为1.25%时,乳胶膜具有较好的光致变色性能。     

Hollow-fiber membranes coated with polymerizable bicontinuous microemulsions

A new method has been successfully employed to prepare hollow-fiber membranes by coating and polymerizing bicontinuous microemulsions onto the internal surfaces of hollow-fiber membranes. The bicontinuous microemulsion consisting of water, a polymerizable zwitterionic surfactant of acryloyloxyundecyl dimethylammonio acetate, methyl methacrylate, and 2-hydroxylethyl methacrylate (HEMA) can form a transparent polymer thin film after polymerization. The hollow-fiber membranes as the supports for microemulsion coatings were fabricated from the spinning solution of polyethersulfone/diethylene glycol/N-methyl-2-pyrrolidone. The microemulsion coated hollow-fiber membranes were evaluated by the separation efficiency and the permeation rate of polyethylene glycol (PEG) solutions. The performance of coated membrane on the PEG separation is strongly dependent on the concentration of HEMA and water in precursor bicontinuous microemulsions. The pore size of the hollow-fiber membranes can be regulated between about 2 to 40 nm by varying the composition of precursor bicontinuous microemulsions. The characteristics of the coated membranes is believed to be directly related to the bicontinuous structures of precursor bicontinuous microemulsions. The use of polymerizable bicontinuous microemulsions enable one to better control the microstructures of coated membranes via in situ polymerization.     

Photoinitiated polymerization in bicontinuous microemulsions: Fluorescence monitoring

The photopolymerization of bicontinuous microemulsions was simultaneously monitored with differential scanning calorimetry and fluorescence. The kinetics and mechanism of the reaction were studied throughout the entire photopolymerization reaction. The role played by the surfactant in the kinetics and morphology was studied. The nature of the surfactant changed the autoacceleration process and final conversion. The behavior was explained as a result of the differences in the interfacial properties. Anionic cetyltrimethylammonium bromide (CTAB) gave rise to a more flexible interfacial film than anionic sodium dodecyl sulfate (SDS), resulting in competition between the intramolecular and intermolecular reactions in the former systems. As cyclization did not contribute to the increase in the degree of crosslinking, SDS photopolymerization gave solids with a more rigid microstructure. Fluorescence methodology was applied to monitor bicontinuous microemulsion polymerization and to reveal the microstructure and morphology development during photopolymerization. The microemulsion composition was designed to prepare nanoporous, crosslinked materials. Even though the nanostructure of the precursor microemulsions was not retained because of phase separation during polymerization, mesoporous solids were obtained. Their morphologies depended on the nature of the surfactant, and membranes with open cells were successfully prepared with CTAB, whereas more complex morphologies resulted with SDS. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5291–5303, 2006     

The influence of sodium dodecyl sulfate/benzyl alcohol/H2O system on the photoisomerization of trans-stilbene

Photoisomerization of trans-stilbene (TS) was investigated in sodium dodecyl sulfate (SDS)/benzyl alcohol (BA)/H(2)O systems in order to establish the relationship between the reaction yields and the compositions and structures of molecular organized assemblies. The results show that, in SDS/BA/H(2)O systems with the structures of oil in water microemulsions, bicontinuous microemulsions, and hexagonal liquid crystals, the reaction yields are much larger than those in benzyl alcohol, both with and without the photosensitizer 9,10-anthracenedicarbonitrile. However, SDS/BA/H(2)O water in oil microemulsion and lamellar liquid crystal can obviously catalyze the photoisomerization of TS only when the photosensitizer is not present. The yield is increased with the increase in H(2)O content or with the decrease in BA content.     

Influence of microemulsions on enantioselective synthesis of (R)-cyclopent-2-enol catalyzed by vitamin B12

The influence of microemulsions on the vitamin B12-catalyzed enantioselective isomerization of 1,2-epoxycyclopentane (1) to form (R)-cyclopent-2-enol (2) has been examined. The reaction was initiated by a reduction of vitamin B12 to the Co(I) form by Zn/NH4Cl. The largest enantiomeric excess (e.e.) in the products was 52% for (R)-2 obtained in a bicontinuous sodium dodecyl sulfate (SDS) microemulsion. A water-in-oil SDS microemulsion gave a poorer percent e.e. probably because of limited catalyst utilization in the water droplets. The influence of the pH of the water phase, the amount of water, and the concentration of vitamin B12 on the enantioselectivity and yield of the reaction was also explored. Results suggest that factors such as higher water content and bicontinuous fluid structure facilitated efficient intermixing of catalyst with reactant to form a key organocobalt intermediate, thus improving enantioselectivity.     

Polymerised bicontinuous microemulsions as stationary phases for capillary electrochromatography

Summary Polymerisation of bicontinuous microemulsions yields porous monolithic structures with well defined pore sizes that are potentially suitable for use as stationary phases for capillary electrochromatography (CEC). A variety of pore sizes can be achieved by altering the composition of the microemulsion, which typically consists of butyl methacrylate (BMA) and ethylene glycol dimethacrylate (EGDMA) as the polymerisable oil phase. The aqueous phase consists of water, a surfactant (sodium dodecyl sulphate, SDS) and a co-surfactant (1-propanol). 2-acrylamido-2-methyl-1-propane sulfonic acid (AMPS) is also added to provide charges along the polymer backbone to allow electroosmotic flow (EOF) to occur. SEM analysis shows that in-situ polymerisation yields a monolithic structure with a porous topography. Investigations have shown that these monoliths are easy to prepare, robust and suitable for the separation of phthalates. They generate higher linear velocities than are achieved using the silica based HPLC packings normally used for CEC.     

Design of highly porous melamine-based networks through a bicontinuous microemulsion templating strategy

Designing low density polymeric porous materials with defined pore sizes (diameters in the 100 nm range) still remains a real synthesis challenge. Here, for the first time, we present a strategy by which bicontinuous microemulsions are used as templating agents for the in-situ aqueous polycondensation of organic resins (melamine formaldehyde, MF). The behaviour of surfactants with different head-groups in systems including oil and MF-containing aqueous phase is studied. While many surfactants are not compatible with aqueous MF precondensates, here we report a non-ionic surfactant either used solely or along with anionic surfactants which prove to be successful at keeping bicontinuous microemulsion systems homogeneous even during early stages of polymerisation. However, upon acid-catalysis it becomes clear that the pore structure of the organic material is largely controlled by the kinetics of phase separation due to the sol–gel process rather than by the thermodynamic equilibrium of the template (microemulsion). Indeed, despite numerous attempts, stabilising the microemulsion interface with zero curvature (bicontinuous) has remained problematic. Instead, we show a new behaviour for the MF resin whereby non-spherical MF morphologies (i.e. thread-like structures) can be obtained by specific interactions between the aqueous amino resin and the acid counterions.     

Radiation-induced polymerization of methyl methacrylate in microemulsion with high monomer content

γ-Ray-induced polymerization of methyl methacrylate was conducted in a microemulsion stabilized by a mixture of sodium of 12-acryloxy-9-octadecenoic acid (AOA) and sodium dodecyl sulfate (SDS) with various weight ratios at room temperature. The experimental data showed that the mixture of AOA and SDS with a weight ratio 2 was an efficient surfactant system for the microemulsion containing 38.6 wt% MMA and 5.5 wt% surfactant. The effects of MMA concentration and dose rate on the polymerization kinetics and particle size are discussed.     

Distribution and Transfer of Gatifloxacin Between Two Microemulsion Phases with Different Structures in SDS/n-C5H11 OH/H2O System

At a weight ratio of n‐C₅H₁₁OH/H₂O=50/50, when the total content of sodium dodecyl sulfate (SDS) was less than 6.0%, the ternary mixture of SDS/n‐C₅H₁₁OH/H₂O coexisted in two immiscible microemulsions. The distribution and transfer of gatifloxacin (GTFX) between the two phases were studied using UV‐Vis and electrochemistry AC impedance spectra. The results show that GTFX transferred from the upper phase (W/O) to the lower phase (O/W or bicontinuous microemulsion), but a small amount of SDS transferred from the lower phase to the upper phase correspondingly with the increase of the total SDS content at a total GTFX concentration of 1.0×10^?5 mol/L. The addition of GTFX did not change the structures of the two different phases fundamentally, but resulted in the transfer and redistribution of GTFX and SDS, so the electric properties of the system were changed correspondingly.     

Characteristics of microemulsion polymerized styrene with water-soluble versus oil-soluble initiators

The effect of oil-soluble versus water-soluble free-radical generators in the polymerization of styrene in oil-in-water (O/W) micromulsions were investigated by photon correlation spectroscopy. The microemulsions were formed by styrene, brine, sodium dodecyl sulfate (SDS), and pentanol. The polymerizations were carried out in two microemulsions that contained droplets differing by a factor of 2.4 in volume. Under the conditions of ? = 0.019 and NaCl/SDS > 2 the microemulsions were stable and the droplets were independent of one another. Both oil-soluble and water-soluble initiators produced polystyrene that contained fractions of two different sizes. In the case of the oil-soluble initiator the droplet size in the microemulsion seemed to be correlated to the size of the product whereas in the case of the water-soluble initiator, there seemed to be little relation.