PEO-LiClO_4-ZSM5 composite polymer electrolyte (IV): Polarized optical microscopy study

All solid-state lithium polymer batteries may be one of the best choices for the future electrochemical power source, characterized by high energy densities, good cyclability, reliability and safety[1,2]. Owing to its potential capability to replace the t…     

Li1.3Al0.3Ti1.7(PO4)3 filler effect on (PEO)LiClO4 solid polymer electrolyte

Composite polymer electrolyte (CPE) films consisting of PEO, LiClO₄, and Li_1.3Al_0.3Ti_1.7(PO₄)₃ with fixed EO/Li = 8 but different relative compositions of the two lithium salts were prepared by the solution casting method. The CPE films were characterized using SEM, DSC, electrical impedance spectroscopy (EIS), and ion transference number measurement. It was found that the incorporation of LiClO₄ and Li_1.3Al_0.3Ti_1.7(PO₄)₃ into PEO by keeping EO/Li = 8 reduced the crystallinity of PEO from 50.34% to the range of 3.57–15.63% depending upon the relative composition of the two salts. The room temperature impedance spectra of the CPE films all exhibited a shape of depressed semicircle in the high frequency range and inclined line in the low frequency range, but the high temperature ones were mainly inclined lines. The Li⁺ ionic conductivity of the CPE films mildly increased and then decreased with increasing Li_1.3Al_0.3Ti_1.7(PO₄)₃ content, and the maximum conductivities were obtained at Li_1.3Al_0.3Ti_1.7(PO₄)₃ content of 15 wt % for all measuring temperatures, for example, 1.378 × 10^?3 S/cm at 100 °C and 1.387 × 10^?5 S/cm at 25 °C. The temperature dependence of the ionic conductivity of the CPE films follows the Vogel–Tamman–Fulcher (VTF) equation The pseudo activation energies (E_a) were rather low, 0.053–0.062 eV, indicating an easy migration of Li⁺ in the amorphous phase dominant PEO. The pre‐exponent constant A and ion transference number t_Li+ were found to have a similar variation tendency with increasing Li_1.3Al_0.3Ti_1.7(PO₄)₃ content and reached their maximums also at Li_1.3Al_0.3Ti_1.7(PO₄)₃ content of 15 wt %. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 743–751, 2005     

Lithium AlPO<Subscript>4</Subscript> composite polymer battery with nanostructured LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode

The borate ester plasticized AlPO₄ composite solid polymer electrolytes (SPE) have been synthesized and studied as candidates for lithium polymer battery (LPB) application. The electrochemical and thermal properties of SPE were shown to be suitable for practical LPB. Nanostructured LiMn₂O₄ with spherical particles was synthesized via ultrasonic spray pyrolysis technique and has shown a superior performance to the one prepared via conventional methods as cathode for LPB. Furthermore, the AlPO₄ addition to the polymer electrolyte has improved the polymer battery performance. Based on the AC impedance spectroscopy data, the performance improvement was suggested as being due to the cathode/polymer electrolyte interface stabilization in the presence of AlPO₄. The Li/composite polymer electrolyte/nanostructured LiMn₂O₄ electrochemical cell showed stable cyclability during the various current density tests, and its performance was found to be quite acceptable for practical utilities at ambient temperature and showed remarkable improvements at 60 °C compared with the solid state reaction counterpart.     

Melt crystallization and segmental dynamics of poly(ethylene oxide) confined in a solid electrolyte composite

The isothermal melt crystallization and the corresponding segmental dynamics, of a high molecular weight poly(ethylene oxide) (PEO) confined by Li₇La₃Zr₂O₁₂ (LLZO) particles in solid electrolyte composites, were monitored by differential scanning calorimetry (DSC) and dielectric relaxation spectroscopy (DRS), respectively. Our results show that the overall crystallinity is positively correlated with the surface area of LLZO particles. The primary and secondary crystallization processes are identified by a modified Avrami equation, while two dynamic modes, the α relaxation and α′ relaxation, were in the DRS measurements. The results reveal an unambiguous correlation between the primary crystallization and the α relaxation, while a correlation between the second crystallization and the α′ relaxation concurrently exist in the electrolyte composites. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 466–477     

Single-ion and salt conductor polymer electrolytes based on poly(4-vinylpyridine) quaternized with poly(ethylene oxide) side chains

A new type of single-ion conductor with fixed cation was synthesized by spontaneous anionic polymerization of 4-vinylpyridine in the presence of short polyethylene oxide ( PEO ) chains as alkylating agents. These comblike polymers have low T_gs and are amorphous with the shorter PEO s. Their conductivities are unaffected by the nature of the anion ( Br ⁻, ClO ₄⁻, and tosylate) and are controlled by the free volume and the mobility of the pendant cation. By comparison of the results at constant free volume, it is shown that the charge density decreases with the increasing length of pendant PEO demonstrating that PEO acts only as a plasticizing agent. Best conductivity results (σ = 10⁻⁵ S cm⁻¹ at 60°C) are obtained with PEO side chains of molecular weight 350. With this sample, the conductivity in the presence of various amounts of added salt (LiTFSI) was studied. A best value of 10⁻⁴ S cm⁻¹ at 60°C is obtained with a molar ratio EO/Li of 10. It is shown that, over the range of examined concentrations (0.2–1.3 mol Li kg⁻¹), the reduced conductivity σ_r/c increases linearly with increasing salt concentration showing that the ion mobility increases continuously. Such behavior is quite unusual since in this concentration range a maximum is generally observed with PEO systems. To interpret this result and by analogy with the behavior of this type of polymer in solution, it is proposed that the conformation of these polymers in the solid state is segregated with the P4VP skeleton more or less confined inside the dense coils surrounded by the PEO side chains. Under the influence of the increasing salt concentration, this microphase separation vanishes progressively: The LiTFSI salt exchanges with the tosylate anions and acts as a miscibility improver agent. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2719–2728, 1997     

Brønsted acid-base polymer electrolyte membrane based on sulfonated poly(phenylene oxide) and imidazole

The Brønsted acid-base polymer electrolyte membrane was prepared by entrapping imidazole in sulfonated poly(phenylene oxide) at the molar ratio of Im/SPPO = 2:1. The hybrid showed a high thermal stability up to 200 °C and peroxide tolerance. Differential scanning calorimetry shows that glass transition temperature is 232 °C. The conductivity increases with temperature exceeding 10⁻³ S/cm above 120 °C and a high conductivity of 6.9 × 10⁻³ S/cm was obtained at 200 °C under 33% RH conditions.     

Theoretical and Experimental Studies on a Metallorganic Complex of (Isopropylxanthato)(Phenyl)Mercury(I) [Hg(I)(C<Subscript>6</Subscript>H<Subscript>5</Subscript>)(C<Subscript>4</Subscript>H<Subscript>7</Subscript>OS<Subscript>2</Subscript>)]

The title compound, (isopropylxanthato)(phenyl)mercury(I), was synthesized and characterized by elemental analysis, IR and thermogravimetric analysis. Density functional theory (DFT) method calculations were performed at B3LYP/CEP-121G and B3LYP/CEP-31G levels of theory, respectively. Vibrational frequencies were predicted, assigned, compared with the experimental values, and they are supported each other. The calculated results show that the strength of bond Hg—C is stronger than that of Hg—S, which is good agreement with the experimental data. The calculations of the second order optical nonlinearity and electronic absorption spectra are also performed.     

A new composite polymer electrolyte based on poly(ethyleneoxide)/ polysiloxane/BMImTFSI/organomontmorillonite

Composite polymer electrolytes based on poly(ethylene oxide)-polysiloxane/l-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide/organomontmorillonite(PEO-PDMS/1L/OMMT) were prepared and characterized.Addition of both an ionic liquid and OMMT to the polymer base of PEO-PDMS resulted in an increase in ionic conductivity.At room temperature,the ionic conductivity of sample PPB100-OMMT4 was 2.19×10~3 S/cm.The composite polymer electrolyte also exhibited high thermal and electrochemical stability and may potentially be applied in lithium batteries.     

Effect of poly(butylene succinate) crystals on spherulitic growth of poly(ethylene oxide) in binary blends of the two substances

The effects of the lamellar growth direction, extinction rings, and spherulitic boundaries of poly(butylene succinate) (PBSU) on the spherulitic growth of poly(ethylene oxide) (PEO) were investigated in miscible blends of the two crystalline polymers. In the crystallization process from a homogeneous melt, PBSU first developed volume‐filling spherulites, and then PEO spherulites nucleated and grew inside the PBSU spherulites. The lamellar growth direction of PEO was identical with that of PBSU even when the PBSU content was about 5 wt %. PEO, which intrinsically does not exhibit banded spherulites, showed apparent extinction rings inside the banded spherulites of PBSU. The growth rate of a PEO spherulite, G_PEO, was influenced not only by the blend composition and the crystallization temperature of PEO, but also by the growth direction with respect to PBSU lamellae, the boundaries of PBSU spherulites, and the crystallization temperature of PBSU, T_PBSU. The value of G_PEO first increased with decreasing T_PBSU when a PEO spherulite grew inside a single PBSU spherulite. Then, G_PEO decreased when T_PBSU was further decreased and a PEO spherulite grew through many tiny PBSU spherulites. This behavior was discussed based on the aforementioned factors affecting G_PEO. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 539–547, 2009     

Poly(N-phenyl-2-hydroxytrimethylene amine): Its blends with poly(ϵ-caprolactone) and water-soluble polyethers

A new polymer with pendant hydroxyl groups, namely, poly(N-phenyl-2-hydroxytrime-thylene amine) (PHA), was synthesized by a direct condensation polymerization of aniline and epichlorohydrin in an alkaline medium. The new polymer is amorphous with a glass transition temperature (T_g) of 70°C. Blends of PHA with poly(ϵ-caprolactone) (PCL), as well as with two water-soluble polyethers, poly(ethylene oxide) (PEO) and poly(vinyl methyl ether) (PVME), were prepared by casting from a common solvent. It was found that all the three blends were miscible and showed a single, composition dependent glass transition temperature (T_g). FTIR studies revealed that PHA can form hydrogen bonds with PCL, PEO, and PVME, which are driving forces for the miscibility of the blends. © 1997 John Wiley & Sons, Inc.     

AFM study of morphological development during the melt-crystallization of poly(ethylene oxide)

The atomic force microscope (AFM) has been used to investigate morphological development during the crystallization of poly(ethylene oxide) (PEO) from the melt. PEOs with molecular weights of 1 × 10⁵ and 7 × 10⁶ were used. Height and amplitude images were recorded, using the tapping mode. For both polymers, the mode of spherulite development varied with the velocity of the growth front. For slow growth velocities, the growth of the crystallites was linear, with growth initially occurring by single lamellae, later developing into growth arms by screw dislocation spawning of crystallites. At intermediate growth velocities, stacks of lamellae develop rapidly. The splaying apart of adjacent crystals and growth arms is abundant. The operation of growth spirals was observed directly in this growth velocity range. The crystals formed by the giant screw dislocations diverge immediately from the original growth direction, providing a source of interlamellar splaying. At low and intermediate velocities, the front propagates by the advance of primary growth arms, with the regions between the arms filled in by arms growing behind the primary front. At the highest velocity observed here, the formation of lamellar bundles and immediate splaying results in recognizable spherulites developing at the earliest stages of crystallization. The change from linear growth to splaying and nonlinear growth are qualitatively explained in terms of driving force, elastic resistance and the presence of compositional and/or elastic fields in the melt. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2311–2325, 1998     

Characteristics of CuAl<Subscript>2</Subscript>-Cu<Subscript>9</Subscript>Al<Subscript>4</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposites synthesized by mechanical treatment

Summary Reactive milling of Cu-hydroxycarbonate - powder aluminium mixture brings many complex chemical reactions such as decomposition, aluminothermic reduction and mechanical alloying resulting in the formation of nanometer size composites that contain intermetallic phases, -Cu₉Al₄ and -CuAl₂, with aluminium oxide.     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. I. Spherulitic morphology and growth by polarized microscopy

The development of the poly(3‐hydroxybutyrate) (PHB) morphology in the presence of already existent poly(vinylidene fluoride) (PVDF) spherulites was studied by two‐stage solidification with two separate crystallization temperatures. PVDF formed irregular dendrites at lower temperatures and regular, banded spherulites at elevated temperatures. The transition temperature of the spherulitic morphology from dendrites to regular, banded spherulites increased with increasing PVDF content. A remarkable amount of PHB was included in the PVDF dendrites, whereas PHB was rejected into the remaining melt from the banded spherulites. When PVDF crystallized as banded spherulites, PHB could consequently crystallize only around them, if at all. In contrast, PHB crystallized with a common growth front, starting from a defined site in the interfibrillar regions of volume‐filling PVDF dendrites. It formed by itself dendritic spherulites that included a large number of PVDF spherulites. For blends with a PHB content of more than 80 wt %, for which the PVDF dendrites were not volume‐filling, PHB first formed regular spherulites. Their growth started from outside the PVDF dendrites but could later interpenetrate them, and this made their own morphology dendritic. These PHB spherulites melted stepwise because the lamellae inside the PVDF dendrites melted at a lower temperature than those from outside. This reflected the regularity of the two fractions of the lamellae because that of those inside the dendrites of PVDF was controlled by the intraspherulitic order of PVDF, whereas that from outside was only controlled by the temperature and the melt composition. The described morphologies developed without mutual nucleating efficiency of the components. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 873–882, 2003     

Role of thermal history on the thermal behavior of poly(<Emphasis Type="Italic">L</Emphasis>-lactic acid) studied by DSC and optical microscopy

Summary The thermal behavior of poly(L-lactic acid) (PLLA) was studied with differential scanning calorimetry (DSC) and polarized optical microscopy. For amorphous PLLA samples, double cold crystallisation peaks were observed in the DSC traces during heating process, being strongly dependent on heating rates. The observation was discussed based on the assumption that the quenched PLLA sample presented some remaining metastable or a precrystalline phase. A small exothermal peak was observed before the main melting peak at low heating rates. The probable reason was discussed through melt-recrystallisation mechanism. Influence of thermal history on the cold crystallisation and melting behavior was also performed on heating process for PLLA samples.     

Observations of crystallization and melting in poly(ethylene oxide)/poly(methyl methacrylate) blends by hot-stage atomic-force microscopy

The binary blend of poly(ethylene oxide)/atactic poly(methyl methacrylate) is examined using hot-stage atomic-force microscopy (AFM) in conjunction with differential scanning calorimetry and optical microscopy. It was found possible to follow in real time the melting process, which reveals itself to be nonuniform. This effect is ascribed to the presence of lamellae having different thicknesses. The crystallization process of poly(ethylene oxide) from the miscible melt is also followed in real time by AFM, affording detailed images of the impingement of adjacent spherulites and direct observation of lamellar growth and subsequent polymer solidification in the interlamellar space.© 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2643–2651, 1998     

Thermodynamic study of the Ag-As-Se and Ag-S-I systems using the EMF method with a solid Ag<Subscript>4</Subscript>RbI<Subscript>5</Subscript> electrolyte

The EMF method with a solid Ag₄RbI₅ superionic conductor was used to study the Ag-As-Se and Ag-S-I systems in the composition ranges of Ag₂Se-As₂Se₃-Se and Ag₂S-AgI-S, accordingly. Their solid-phase equilibrium diagrams are constructed or specified. The existence of ternary AgAs₃Se₅, AgAsSe₂, Ag₃AsSe₃, Ag₇AsSe₆, Ag₃SI compounds is confirmed. The standard partial and integral thermodynamic formation functions and also standard entropies were calculated for these compounds for the first time.     

Poly(ethylene oxide)/poly(methyl methacrylate) (semi-)interpenetrating polymer networks: Synthesis and phase diagrams

Interpenetrating polymer networks (IPNs) of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) were prepared by simultaneous network formation. The PEO network was produced by acid-catlayzed self-condensation of α,ω-bis(triethoxysilane)-terminated PEO in the presence of small amounts of water. The PMMA network was formed by free radical polymerization of MAA in the presence of divinylbenzene as crosslinker. The reaction conditions were adjusted to obtain similar crosslinking kinetics for both reactions. An attempt was made to construct a phase diagram of the IPNs by measuring the composition of the IPNs at the moment of the appearance of the phase separation, as indicated by the onset of turbidity. This composition could be determined because the siloxane crosslinks of the PEO network could be hydrolyzed in aqueous NaOH with the formation of linear, soluble PEO chains. The phase diagram was compared with phase diagrams of blends of linear polymers and of semi-IPNs (crosslinked PMMA and linear PEO), obtained under similar conditions, i.e. polymerization of MMA in the presence of varying amounts of PEO. It was observed that the form of the phase diagrams of the linear polymers is similar to that of the IPNs, but is quite different from that of the semi-IPNs. Thus, homogeneous transparent materials containing up to 60% of PEO could be prepared in the blends and the IPNs, but in the semi-IPNs, phase separation occurred with PEO contents as low as 10%.     

Controlled sulfonation of poly(arylene ether sulfone)s and poly(arylene ether ketone)s with different molecular structures for polymer electrolyte membranes

Poly(arylene ether sulfone) copolymers derived from 9,9-bis(4-hydroxyphenyl)fluorene, bisphenol S and 4,4′-difluorodiphenylsulfone and poly(arylene ether ketone) copolymers derived from 4-phenoxybiphenyl, diphenyl ether and isophthaloyl chloride were prepared as precursor polymers for sulfonation reaction in which sulfonic groups are introduced quantitatively into specified positions. Sulfonation reaction for these two series of copolymers by concentrated sulfuric acid was successfully carried out to give sulfonated polymers with controlled positions and degree of sulfonation. Thermal stability, moisture absorption and proton conductivity for these two series of copolymers were measured and the results were compared to those of perfluorosulfonic acid polymers.     

Formation of Composites Based on CsHSO<Subscript>4</Subscript> and Cs<Subscript>5</Subscript>H<Subscript>3</Subscript>(SO<Subscript>4</Subscript>)<Subscript>4</Subscript> and Mechanism of Their Protonic Conduction

Vibrational spectra of finely divided amorphous CsHSO₄,Cs₅H₃(SO₄)₄ · H₂O, and composites based on these are measured and analyzed. An analysis of the spectra indicates the occurrence of substantial changes in the system of hydrogen bonds and in the spectral range of the sulfate group of acid sulfates in the composites. Structural dynamics of the SO₄ tetrahedrons is in full conformance with protonic conduction and the data of x-ray diffraction analyses accompanied by differential scanning calorimetry. It is shown that mobility of protons in the composites increases. A mechanism of the formation of the composites and their conduction is proposed.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 640–645.Original Russian Text Copyright © 2005 by Ponomareva, Lavrova, Burgina.     

Synthesis and characterization of ternary hybrid material based on poly-o-methoxyaniline and poly(ethylene oxide) in mesostructured V<Subscript>2</Subscript>O<Subscript>5</Subscript>

New hybrid composites based on mesostructured V₂O₅ containing intercalated poly(ethylene oxide), poly-o-methoxyaniline and poly(ethylene oxide)/poly-o-methoxyaniline were prepared. The results suggest that the polymers were intercalated into the layers of the mesostructured V₂O₅. Electrochemical studies showed that the presence of both polymers in the mesostructured V₂O₅ (ternary hybrid) leads to an increase in total charge and stability after several cycles compared with binary hybrid composites. This fact makes this material a potential component as cathode for lithium ion intercalation and further, a promising candidate for applications in batteries.