TiO2一维纳米材料及其纳米结构的合成

本文对合成TiO₂一维纳米材料及其有序纳米阵列的阳极氧化法、模板法以及水热法进行了全面而系统的评述，着重介绍了它们的最新研究进展。阳极氧化法能制备牢固负载于基体上的TiO₂纳米管阵列，这有助于构筑TiO₂纳米结构及其在纳米器件上的应用；与多种制备技术如溶胶－凝胶工艺、电化学沉积以及原子层沉积等相结合，模板法可以合成出多种形貌的TiO₂纳米材料如纳米管、纳米线和纳米棒，并可以通过改变所用模板的微观尺寸来调控TiO₂一维纳米材料及其有序阵列的微结构参数；水热合成法可以制备出直径小且比表面积大的TiO2纳米管粉末。但从目前看来，该法还不能制备出牢固负载于基体上的有序纳米阵列。文章最后指出了TiO₂一维纳米材料及其有序纳米阵列合成中存在的问题及今后发展方向。     

阳极氧化法制备二氧化钛纳米管阵列的研究

采用电化学阳极氧化法,将纯钛浸入HF酸水溶液,在钛基体表面原位构建高度有序的二氧化钛纳米管阵列,探讨阳极氧化电压、电解液浓度和电解液温度等对二氧化钛纳米管阵列尺寸和形貌的影响。通过SEM、XRD对二氧化钛纳米管阵列的结构特征进行表征,结果表明,不同的阳极氧化电压、电解液浓度和温度都将影响TiO2纳米管阵列的尺寸和形貌,在阳极氧化电压为20V,HF电解液浓度为0.5%t条件下,可制备出结构规整有序的TiO2纳米管阵列。     

AAO模板对液相沉积TiO2纳米阵列结构的影响

采用液相沉积法(LPD),在不同的阳极氧化铝(AAO)模板上原位合成高度有序的TiO2纳米阵列.实验结果表明,经过400℃热处理后,制备出的薄膜是锐钛矿相的TiO2纳米阵列,草酸AAO模板中Al2O3的体积分数大于0.71,薄膜由TiO2纳米棒组成,外径约为100 nm左右;而磷酸AAO模板中Al2O3的体积分数小于0.71,液相沉积后获得TiO2纳米管,管外径达200 nm左右,内径约为100 nm左右.     

阳极氧化法制备TiO2纳米管及光催化研究进展

TiO2纳米管是一种新型的高性能材料,因其独特的有序结构而显示出优异的性能,在许多领域有着广泛的应用。本文主要阐述了阳极氧化法制备TiO2纳米管及其纳米管生成的机制,分析了制备过程中电解液pH、阳极氧化电压对所生成的TiO2纳米管阵列结构的影响。实现TiO2纳米管定向排布,对于发挥低维材料的效用至关重要。高度有序的纳米管阵列结构,具有显著的量子尺寸效应和取向效应。对TiO2纳米管阵列进行掺杂改性能够增强材料的光催化性能,提高其光催化效率。在光照条件下,光生电子能快速从TiO2纳米管的导带进入导电基体,大大降低了光生载流子复合几率,从而使其表现出良好的光电活性,可用于太阳能电池领域,在抗菌消毒,污水处理方面也具有很大的应用价值。     

NH4F/H3PO4体系中阳极氧化法制备TiO2纳米管阵列

以价廉的Ni板代替常用的Pt片为阴极,纯钛为阳极,采用电化学阳极氧化法在NH4F-H3PO4体系中制备出TiO2纳米管阵列.详细研究了制备参数(溶液酸度、氟离子浓度、外加电压和氧化时间)对所获纳米管阵列形貌的影响.采用场发射扫描电镜(FE-SEM)和X射线衍射(XRD)对样品的形貌和晶相结构进行了表征.在最优化的条件下,可以获得形貌规整、表面干净、有序的TiO2纳米管阵列.纳米管阵列的平均管径为60 nm.管长约530 nm.采用阳极氧化法制备的纳米管阵列是非晶态的.经400℃热处理2 h后,可以转变为锐钛矿相.实验结果还发现,经过热处理后,纳米管阵列变得更为有序,管径扩大至约95 nm.     

脉冲电沉积法制备Pt-TiO2 纳米管电极及其电催化性能

采用阳极氧化法在高纯钛片上原位组装TiO2纳米管阵列, 然后用脉冲电沉积方法将Pt沉积到TiO2纳米管阵列上, 制备出Pt-TiO2纳米管电极. 利用XRD和SEM对所获电极的微观结构和形貌进行表征, 结果表明, Pt纳米颗粒以花簇状分散在TiO2纳米管上, 晶粒大小约为25.6 nm. 对甲醇的电催化性能的研究结果表明, 脉冲电沉积制得的Pt-TiO2纳米管电极比TiO2纳米管电极和纯Pt片电极具有更高的电催化活性, 是Pt电极的40多倍.     

阳极氧化法制备TiO_2纳米管阵列膜及其应用

由阳极氧化法制备的TiO2纳米管阵列,因其独特的有序结构而显示出优异的性能,在许多领域有着广泛的应用,成为一种很有发展前景的新型纳米结构材料。本文简要综述了制备TiO2纳米管阵列结构的方法及其应用研究进展。在比较了当前几种制备TiO2纳米管阵列方法的优缺点后,重点讨论了阳极氧化法制备TiO2纳米管阵列结构过程中,如何通过调整工艺参数来实现此类纳米管阵列结构的可控生长。最后评述了TiO2纳米管阵列材料研究的发展趋势和应用前景。     

纳米镍修饰TiO2纳米管电极检测胰岛素

采用阳极氧化法制备出高度有序的TiO2纳米管阵列作为基础电极,通过电沉积法将纳米镍颗粒负载在基础电极上,从而制备了纳米镍-二氧化钛纳米管(Ni/TiO2NTs)修饰电极。分别采用扫描电子显微镜和X射线衍射对Ni/TiO2NTs电极的形貌及组分进行了表征。将Ni/TiO2NTs电极用于对胰岛素的电化学测定。结果表明,在0.1 mol/L NaOH支持电解液中,胰岛素在Ni/TiO2NTs电极上有较好的电化学响应,胰岛素浓度在0.8～1.6μmol/L范围内,峰电流密度与其浓度呈良好的线性关系,检测限为0.28μmol/L,灵敏度为0.49×10-3 A/(μmol·L-1.cm-2)。     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基底表面制备一层TiO2纳米管阵列薄膜,然后通过水热反应在TiO2纳米管上负载CdS纳米粒子,形成CdS/TiO2纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO2纳米管的光电性能和光催化活性,结果表明,相比于TiO2纳米管,CdS/TiO2纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

甘油基电解液中阴离子对阳极氧化TiO2纳米管生长的影响

在NH4F-甘油-水电解液中, 采用阳极氧化法, 在纯Ti基底上制备了高度取向的TiO2纳米管阵列, 考察了阴离子种类、阳极氧化时间及NaAc浓度对纳米管阵列生长的影响. 结果表明, TiO2纳米管的生长速率和长度强烈依赖于阴离子的种类和浓度. NaNO3和NaCl的加入能增大阳极氧化时的电流密度, 提高TiO2纳米管底部的腐蚀速率, 提高管的生长速率及增加管的长度; 而NaAc的加入更大程度上抑制了已生成的TiO2纳米管顶部的溶解, 提高了纳米管的净生长速率, 得到较长的纳米管阵列.     

Robust S-doped TiO2@N,S-codoped carbon nanotube arrays as free-binder anodes for efficient sodium storage

Titanium dioxide(TiO_2) has been investigated broadly as a stable,safe,and cheap anode material for sodium-ion batteries in recent years.However,the poor electronic conductivity and inherent sluggish sodium ion diffusion hinder its practical applications.Herein,a self-template and in situ vulcanization strategy is developed to synthesize self-supported hybrid nanotube arrays composed of nitrogen/sulfur-codoped carbon coated sulfur-doped TiO_2 nanotubes(S-TiO_2@NS-C) starting from H_2 Ti_2 O_5-H_2 O nanoarrays.The S-TiO_2@NS-C composite with one-dimensional nano-sized subunits integrates several merits.Specifically,sulfur doping strongly improves the Na~+ storage ability of TiO_2@C-N nanotubes by narrowing the bandgap of original TiO_2.Originating from the nanoarrays structures built from hollow nanotubes,carbon layer and sulfur doping,the sluggish Na~+ insertion/extraction kinetics is effectively improved and the volume variation of the electrode material is significantly alleviated.As a result,the S-TiO_2@NS-C nanoarrays present efficient sodium storage properties.The greatly improved sodium storage performances of S-TiO_2@NS-C nanoarrays confirm the importance of rational engineering and synthesis of hollow array architectures with higher complexity.     

阳极氧化铝模板限域制备一维杂化纳米材料及其多样化应用的研究进展

一维杂化纳米材料以其独特的物理化学性质,在电学、光学、催化等领域得到了广泛的应用。 其制备方法对一维杂化纳米材料性能的改变和调控显得至关重要。 模板法作为一种简单而普适的合成工艺,近几年来被广泛应用于纳米结构和纳米阵列的合成。 本文主要介绍了阳极氧化铝(AAO)模板法制备一维杂化纳米材料整体情况、AAO模板结合其他技术材制备材料的方法、一维杂化纳米材料在刺激响应性器件、能量存储与转换器件、催化等众多领域的应用。     

Influence of anodizing voltage mode on the nanostructure of TiO2 nanotubes

The nanostructure of self-ordered porous anodic TiO₂ nanotubes (PATNTs) has extraordinary influence on their physical and chemical properties. For this reason, extensive attention has been paid on pulse anodization to regulate the nanostructure of PATNT. However, the relationships between the nanostructures and current curves still remain unclear. Based on the traditional potentiostatic and pulse anodizations, five different modes (i.e., potentiostatic, pulse, triangle wave, decrease, and increase step by step) of applied voltage and their influences on the nanostructures of PATNT have been investigated in detail. The growing rates of the nanotubes anodized under five different modes were compared for the first time. The results show that the growing rate of pulse voltage anodization is the fastest, reaching 116.4 nm min^?1. The slowest is triangle wave voltage anodization, only 59.3 nm min^?1. When the applied voltage decreases step-by-step, branched nanotubes can be formed in the bottom of PATNT. Yet, when the applied voltage increases step-by-step, triple-layer nanotubes with different diameters are formed, and the forming mechanism of this special nanostructure is discussed. The present results may be helpful to understand the mechanism of PATNT and facilitate the assembling diverse nanostructures for extensive applications in photocatalysis, dye-sensitized solar cells, and biomedical devices.     

Hydrothermal synthesis of carbon nanotube/cobalt oxide core-shell one-dimensional nanocomposite and application as an anode material for lithium-ion batteries

Carbon nanotube/cobalt oxide core-shell one-dimensional nanostructures were prepared via a hydrothermal synthesis method, in which nanosize cobalt oxide crystals were homogeneously coated on the surface of carbon nanotubes. The morphologies and crystal structures of the as-prepared core-shell nanocomposites were analysed by X-ray diffraction, field emission gun scanning electron microscopy, and transmission electron microscopy. When applied as anodes in lithium-ion cells, carbon nanotube/cobalt oxide core-shell nanostructures exhibited an initial lithium storage capacity of 1250 mAh/g and a stable capacity of 530 mAh/g over 100 cycles. The good electrochemical performance could be attributed to the nanocrystalline cobalt oxide and the unique core-shell one-dimensional nanostructures.     

Aqueous solution route to high-aspect-ratio zinc oxide nanostructures on indium tin oxide substrates

High-aspect-ratio ZnO nanowires and nanotubes are formed on indium tin oxide (ITO) substrates using a three-step route at low temperatures. The three steps, including successive ionic layer absorption and reaction (SILAR) deposition of the ZnO seed layer, hydrothermal annealing of the seed layer, and chemical bath deposition (CBD) of the one-dimensional (1D) ZnO nanostructures, are all conducted in aqueous solutions at temperatures below 120 degrees C. Both the hydrothermal annealing of the SILAR seed layer and the low-concentration precursor solution employed in the CBD process are crucial in order to synthesize the uniform and high-aspect-ratio ZnO nanostructures on the ITO substrate. TEM analyses reveal that both the nanowire and the nanotube possess the single-crystal structure and are grown along [001] direction. Room-temperature cathodoluminescence spectrum of the 1D ZnO nanostructures shows a sharp ultraviolet emission at 375 nm and a broad green-band emission.     

A self-seeded, surfactant-directed hydrothermal growth of single crystalline lithium manganese oxide nanobelts from the commercial bulky particles

Single crystalline lithium manganese oxide nanobelts were obtained through a self-seeded, surfactant-directed growth process from the commercial bulky particles under hydrothermal treatment. A possible mechanism was proposed to explain the growth of the nanobelts. This new process could be extended to prepare other one-dimensional nanomaterials such as Se nanorods, Te nanotubes, and MnO2 nanowires.     

复杂一维纳米材料的构筑及储钠性能

一维纳米材料因其独特的结构和物化性质而被广泛应用于能源存储与转换等领域. 钠离子电池由于钠资源储量丰富和成本低廉等特点而有望用于大规模能源存储. 随着能源需求的不断增长和研究的日益深入,一维纳米材料也经历着结构从简单到复杂、性能从一般到优异的演变. 因此,构筑结构复杂独特、储钠性能优异的一维纳米材料已成为储能领域的热点之一. 结合当前的研究热点和本课题组的研究进展,本文重点阐述了有机酸辅助干燥法、水热法和静电纺丝法制备复杂一维纳米材料的详细机理及其储钠性能,材料包括束状纳米线、介孔纳米管、豌豆状纳米管和离子预嵌入纳米带等,并对它们的结构与储钠性能相关性进行了详细分析. 这为一维纳米材料后续的研究和应用提供了一定的指导和帮助.     

Crystal structures, anisotropic growth, and optical properties: controlled synthesis of lanthanide orthophosphate one-dimensional nanomaterials

The fundamental understanding of the relationship between crystal structure and the dynamic processes of anisotropic growth on the nanoscale, and exploration of the key factors governing the evolution of physical properties in functional nanomaterials, have become two of the most urgent and challenging issues in the fabrication and exploitation of functional nanomaterials with designed properties and the development of nanoscale devices. Herein, we show how structural and kinetic factors govern the tendency for anisotropic growth of such materials under hydrothermal conditions, and how the crystal structure and morphology influence the optical properties of Ln3+-doped nanocrystals. The synthesis of phase-pure and single-crystalline monoclinic, hexagonal, and tetragonal one-dimensional LnPO4 nanostructures of different aspect ratios by means of kinetically controlled hydrothermal growth processes is demonstrated. It is shown that the tendency for anisotropic growth under hydrothermal conditions can be enhanced simply by modifying the chemical potentials of species in the reaction solution through the use of carefully selected chelating ligands. A systematic study of the photoluminescence of various Eu3+-doped lanthanide phosphates has revealed that the optical properties of these nanophosphors are strongly dependent on their crystal structures and morphologies.     

Functionalized Carbon Nanomaterials Derived from Carbohydrates

A tremendous growth in the field of carbon nanomaterials has led to the emergence of carbon nanotubes, fullerenes, mesoporous carbon and more recently graphene. Some of these materials have found applications in electronics, sensors, catalysis, drug delivery, composites, and so forth. The high temperatures and hydrocarbon precursors involved in their synthesis usually yield highly inert graphitic surfaces. As some of the applications require functionalization of their inert graphitic surface with groups like ? COOH, ? OH, and ? NH₂, treatment of these materials in oxidizing agents and concentrated acids become inevitable. More recent works have involved using precursors like carbohydrates to produce carbon nanostructures rich in functional groups in a single‐step under hydrothermal conditions. These carbon nanostructures have already found many applications in composites, drug delivery, materials synthesis, and Li ion batteries. The review aims to highlight some of the recent developments in the application of carbohydrate derived carbon nanostructures and also provide an outlook of their future prospects.