SDS对镍在HNO3/Cl-/H2O体系中电化学振荡行为的影响

阴离子表面活性剂十二烷基硫酸钠(SDS)能够控制金属镍在0.5 mol•L-1 HNO3/0.005 mol•L-1 Cl-/H2O溶液中的电流振荡行为. 在电流振荡过程中, 镍电极微分电容和电导等均出现明显的振荡特性. 随着SDS浓度的增大, 镍表面微分电容和溶液电导振幅等值均逐渐减小. 并且对SDS在镍电流振荡和钝化过程中的作用原理给予解释.     

全钒液流电池高浓度下V(IV)/V(V)的电极过程研究

采用循环伏安、低速线性扫描和阻抗技术, 以石墨为电极, 研究了V(IV)/V(V)在较高浓度下的电极过程. 结果表明, 采用2.0 mol•L-1 的V(IV)溶液时, H2SO4浓度低于2 mol•L-1, V(IV)/V(V)反应极化大, 可逆性差, 表现为电化学和扩散混合控制; H2SO4浓度增至2 mol•L-1以上, V(IV)/V(V)反应的可逆性提高, 转为扩散控制, 且增加H2SO4浓度有利于阻抗的降低; 但H2SO4浓度超过3 mol•L-1, 溶液的粘度和传质阻力大, 阻抗反而增大. 在3 mol•L-1的H2SO4中, 随着V(IV)浓度的增加, 体系的可逆性和动力学改善, 阻抗减小; 但V(IV)浓度超过2.0 mol•L-1, 较高的溶液粘度导致溶液的传质阻力迅速增加, V(IV)/ V(V)的电化学性能衰减, 阻抗增大. 因此, 综合考虑电极反应动力学和电池的能量密度两因素, V(IV)溶液的最佳浓度为1.5～2.0 mol•L-1, H2SO4浓度为3 mol•L-1.     

2-羟基-3-(三乙胺基)丙基十烷基硫醚修饰电极测定痕量金

研究了 2 羟基 3 (三乙胺基 )丙基十烷基硫醚 (HTPSD)修饰玻碳电极测定金的伏安特性及分析条件。在 0 .2mol·L- 1KCl HCl缓冲溶液中 (pH 1) ,金 (Ⅲ )被富集到电极表面 ,然后介质交换到 0 .2mol·L- 1KCl HCl空白溶液中 (pH 1)进行阴极溶出伏安测定 ,金 (Ⅲ )浓度在 2× 10 - 81× 10 - 6mol·L- 1范围内呈线性关系。检出限为 1× 10 - 8mol·L- 1。相对标准偏差小于 6 2 % ,一般常见离子不干扰。     

硫脲对块体纳米晶工业纯铁在盐酸溶液中的缓蚀行为

采用电化学阻抗谱(EIS)研究了硫脲对室温下1 mol•L－1盐酸溶液中粗晶和纳米晶工业纯铁的腐蚀行为的影响.从EIS的拟合结果得知,在1 mol•L－1盐酸溶液中,块体纳米晶工业纯铁比粗晶工业纯铁腐蚀倾向小.基于纳米晶和粗晶工业纯铁在添加有硫脲的1 mol•L－1盐酸溶液中阻抗谱随浸泡时间的变化关系,观察到以下现象,当浸泡时间短至5 min时,对应不同浓度(50、100、150、500 mg•L－1)的缓蚀剂添加量,在粗晶工业纯铁的阻抗复平面图上出现一感抗弧,而在纳米晶工业纯铁的阻抗复平面图是一圆心下偏的容抗弧.随着浸泡时间的延长,两种样品的容抗弧半径增大,在150 mg•L－1的浓度时,电荷传递电阻(Rct)出现极值,这表明硫脲是一种吸附型缓蚀剂.抗盐酸腐蚀性能的提高和没有感抗弧的出现, 归因于体纳米化的结果,这与体纳米化的制备技术密切相关.     

Co(III)离子在二氧化铅电极上的阳极形成

文献上曾报导过Co(Ⅱ)离子具有加速PbO_2电极上氧阳极析出过程的作用,并表明当Co(Ⅱ)离子存在时,氧的析出过程有可能通过表面吸附的高价钴氧化物氧化水分子而形成.本文通过浓硫酸溶液中Co(Ⅱ)阳极氧化为Co(Ⅲ)以及O_2阳极析出动力学的研究,表明了O_2的析出和Co(Ⅲ)的形成是通过吸附在电极表面的高价钴(Ⅳ)的OH 基配合物分别氧化水分子和Co(Ⅱ)离子形成的,它与Cr(Ⅲ)、Mn(Ⅱ)离子的阳极氧化过程相类似,而不是通过Co(Ⅱ)离子直接放电形成的.本文利用文献所述的研究方法.在固定硫酸浓度(3.4mol·kg~(-1))下,研究CoSO_4浓度(0.05—0.35mol·drn~(-3))对于O_2和Co(Ⅲ)阳极形成过程分别的影响.在固定CoSO_4(0.2mol·     

水解聚合铝溶液中Al5和Al9的制备及初步表征

以相图理论为指导,采用铝粉、水合氯化铝和水为原料,创造氯化铝不断水解的条件,通过调整反应温度、原料配比及溶液碱化度,经蒸发、结晶制成了铝盐水解聚合产物中的两种中间产物：水合氯化五聚铝AlCl3•4Al(OH)3•7.5H2O和水合氯化九聚铝2AlCl3•7Al(OH)3•18H2O,分别采用粉末XRD物相分析、化学分析和IR对其进行了表征.以化学分析为主要监测手段,对AlCl3•4Al(OH)3•7.5H2O和2AlCl3•7Al(OH)3•18H2O形态过程进行了研究,结果表明,温度对于产物的行成及性能有很大的影响,并且反应随温度的变化基本上是一个可逆的过程,同时,实验表明 75℃为AlCl3•4Al(OH)3•7.5H2O和2AlCl3•7Al(OH)3•18H2O析出的最佳温度,该温度下产物的产率较高且结晶状态良好.     

离子对水的17O-NMR化学位移和水结构的影响

在小于1 mol•L-1的浓度范围内,测试了碱金属、碱土金属氯化物、卤化钠及其它常见含氧酸盐溶液的17O-NMR化学位移（δ(H217O)）.发现离子对δ(H217O)的影响与离子的半径、电荷、离子外层电子结构及离子结构有关.其它离子参数相同时,离子半径越大,离子的摩尔δ(H217O)越大;在电子结构相同的情况下,离子电荷越大,离子的摩尔δ(H217O)越大;多原子离子的摩尔δ(H217O)更多地是与其离子结构相关.离子的摩尔δ(H217O)的大小反映了该离子对水的结构的影响情况,离子的摩尔δ(H217O)越大,对水的结构促进作用越强.     

拉曼光谱研究CaCl2和MgCl2对水结构的影响

测试了CaCl2、MgCl2溶液(浓度小于1.0 mol•L-1)的OH伸缩振动区域的拉曼光谱.对所得到的拉曼光谱进行了计算机去卷积处理,并由此计算了不同溶液中水的四面体结构的百分数.研究表明,CaCl2、MgCl2对水中四面体结构有破坏作用，且CaCl2的破坏作用比MgCl2大.与17O核磁共振结果对比与分析,认为CaCl2、MgCl2虽然破坏水中的四面体结构,但通过促进含氢键数少的水分子形成氢键,故从总体上促进水的缔合结构.     

烟酸对酸性硫酸盐体系铜电沉积的影响

对溶液A: 0.8 mol•L－1硫酸铜,0.6 mol•L－1硫酸,5.0×10－5 mol•L－1氯离子,1.0×10－4 mol•L－1聚乙二醇的溶液,溶液B:在溶液A中加入2.0×10－2 mol•L－1烟酸,pH为0.5,运用循环伏安和计时安培法研究玻碳电极上铜的电沉积行为.结果表明,铜的电沉积过程经历了晶核形成过程,其电结晶按瞬时成核和三维生长方式进行.烟酸的加入对铜的电沉积具有阻化作用,但不改变铜的电结晶机理.沉积层的X射线衍射表明Cu为面心立方结构,在烟酸存在下沉积层出现(220)高择优取向,这可能是烟酸在Cu(220)晶面上发生强烈吸附作用的结果.     

新型不对称双季铵盐缓蚀剂在HCl中对Q235钢的缓蚀行为

采用静态失重法、极化曲线法和交流阻抗法研究了自制的含咪唑啉环不对称双季铵盐缓蚀剂(DBA)在1 mol•L^－1 HCl介质中对Q235钢的缓蚀性能, 并探讨了其在Q235钢表面的吸附行为. 结果表明, 缓蚀效率随DBA浓度增加而增大, 在25～55 ℃的实验温度范围内, 浓度为2.89×10^－4 mol•L^－1时, 缓蚀效率均在90%以上, 且缓蚀效率随温度升高而增大. 极化曲线测试显示DBA是一种阴极抑制为主的混合型缓蚀剂. 缓蚀剂在Q235钢表面的吸附过程为吸热过程, 其在Q235钢表面的吸附遵循Langmuir等温式, 属于化学吸附. 最后采用量子化学方法对DBA的缓蚀机理做了进一步分析.     

离子色谱-直接电导法测定碱土金属和过渡金属离子

本文报道离子色谱-直接电导法测定碱土金属和过渡金属离子。研究了流动相pH值、乙二胺浓度及柠檬酸和酒石酸浓度对金属离子分离的影响。结果表明,以乙二胺-柠檬酸为流动相可以同时分离碱土金属和过渡金属离子。用乙二胺-酒石酸作为流动相可以分离碱土金属离子。方法检出限为0.09~1.88 mg/L,加标回收率为97.6%~98.7%。该方法用于叶面肥试样的分析,结果良好。     

阳离子交换色谱中色谱柱温度对碱金属与碱土金属离子保留的影响

研究了非抑制型阳离子交换色谱中色谱柱温度(25~50℃)对碱金属离子(Li+、Na+、K+、Rb+)和碱土金属离子(Mg2+、Ca2+、Sr2+)以及NH4+保留的影响。在Shim-pack IC-C1磺酸型阳离子交换柱上,以硝酸为流动相分离碱金属离子,以乙二胺或乙二胺-草酸(柠檬酸)为流动相分离碱土金属离子,随着色谱柱温度的升高,碱金属和碱土金属离子的保留时间均增长,其范特霍夫曲线具有良好的线性关系,斜率为负值,表明在此条件下碱金属和碱土金属离子的保留为吸热过程。在Shim-pack IC-SC1羧酸型阳离子交换柱上,以硫酸为流动相同时分离碱金属和碱土金属离子,随着色谱柱温度的升高,Mg2+、Ca2+的保留时间增长,而K+、Rb+的保留时间缩短,Li+、Na+、NH4+的保留时间基本不变。在此条件下,Mg2+、Ca2+、K+和Rb+的范特霍夫曲线具有良好的线性关系,其中Mg2+和Ca2+的曲线斜率为负值,K+和Rb+的曲线斜率为正值,表明Mg2+和Ca2+的保留表现为吸热过程,K+和Rb+的保留表现为放热过程。研究表明在不同固定相和流动相条件下,色谱柱温度对碱金属和碱土金属离子保留行为的影响不同。     

Study of Host-Guest Complexation of Alkaline Earth Metal Ion,Aluminum Ion and Transition Metal Ions with Crown Ethers by Fast Atom Bombardment Mass Spectrometry

Complexations of crown ethers with alkali metal ions have been investigated extensively by FAB mass spectrometry over the past decade, but very little attention has been paid to reactions of crown ethers with other classes of metal ions such as alkaline earth metal ions, transition metal ions and aluminum ions. Although fast atom bombardment ionization mass spectrometry has proven to be a rapid and convenient method to determine the binding interactions of crown ethers with metal ions, problems in reliabilities for quantitative measurements of” binding strength for the host-guest complexes have been described in the literature. Thus, in this paper, applications of FAB/MS for investigating the complexation of crown ethers with various classes of metal ions is discussed. Extensive fragmentations for neutral losses such as C₂H₄O or C₂H₄ molecules from the host-guest complexes could be observed. The reason is attributed to the energetic bombardment processes of FAB occuring in the formation of these complexes. Complexes of cyclen with metal ions also show neutral losses of C₂H₄NH molecules leading to fragment ions. Transition metal ions usually form (Crown + MCl)⁺ type of ions, alkaline earth metal ions can form both (Crown + MCl)⁺ and (Crown + MOH)⁺ type of ions. But for aluminum ions, only (Crown + Al(OH)₂)⁺ type of ions could he observed.     

Investigation of the Hydrolysis Stability of Triazine Tricarboxylate in the Presence of Transition Metal(II) Ions and Synthesis and Crystal Structure of the Alkaline Earth Triazine Tricarboxylates M3[C3N3(CO2)3]2·12H2O (M = Sr,Ba)

The stability against hydrolysis of triazine tricarboxylate (TTC) in the presence of divalent transition metal and alkaline earth ions was investigated by means of X‐ray diffraction and FTIR spectroscopy. Depending on the size of the cation either formation of the respective triazine tricarboxylate salts or hydrolysis of TTC yielding oxalate was observed. The hydrolysis of TTC induced by transition metal ions could be explained in analogy to the hydrolysis of triazine tris(2‐pyrimidyl) as a result of ring tension caused by the coordination of these ions. By the reaction of potassium triazine tricarboxylate with alkaline earth salts in aqueous solution the alkaline earth triazine tricarboxylates M₃[C₃N₃(CO₂)₃]₂ · 12H₂O (M = Sr, Ba) were obtained and analyzed by single‐crystal X‐ray diffraction. The isotypic salts represent the first examples of alkaline earth triazine tricarboxylates and the first TTC salts comprising solely divalent cations.     

碱土金属与多卤代偶氮氯膦类试剂显色反应的研究

近年来合成的多卤代偶氮氯膦类试剂有希望成为一类有效的碱土金属显色剂。本文研究了此类试剂与钙、锶、钡所生成配合物的吸收光谱、显色酸度、选择性、灵敏度和配合物的组成,以及试剂结构与性能的关系等。说明了不同取代助色基对显色反应各方面的影响。通过研究筛选出了较好的碱土显色剂,这几种试剂的结构如下:     

四环素类抗菌素碱性降解物与碱土金属螯合物的荧光研究

临床医学发现,给病人服用四环素后定时测定体液中四环素含量,可以诊断胃癌~[1],因此.建立灵敏、准确的四环素测定方法具有重要意义.已知四环素类抗菌素与一些金属离子有很强的螯合能力,并能生成有色螯合物,其中以锆、钍、铀、锌、铜、铝、镁、铈及钴的螯合物尤为稳定,可用于鉴别、测定四环素类抗菌素的含量.一些螯合物也用于荧光测定~[2～6],但     

Developments in Titanium-Based Alkali and Alkaline Earth Metal Oxide Catalysts for Sustainable Biodiesel Production: A Review

Biodiesel represents a biodegradable, environmentally friendly, and renewable alternative to fossil fuels. Despite more than three decades of research, significant obstacles still hinder the widespread production of biodiesel. This current review elucidates both the potential and the existing challenges associated with homogeneous and heterogeneous catalysts in catalyzing biodiesel production, with a particular focus on alkali analogues, alkaline earth metal oxides, and titania-based catalysts. In particular, a comprehensive analysis is presented concerning alkali and alkaline earth-based titania (TiO₂) catalysts. Among these, the alkaline earth metal oxides, including lithium, calcium, and strontium when combined with titanium-based catalysts, exhibit superior catalytic activity compared to other metal oxides, owing to their heightened basicity. Consequently, this review offers a thorough and up-to-date insight into the potential of titania-based heterogeneous catalysts for advancing biodiesel production.     

Tetra(diethyl)amide-p-tert-butyl-thiacalix[4]arene in Cone Conformation: Synthesis and Binding Properties with Alkali,Alkaline Earth,Heavy and Transition Metal Ions

Tetra(diethyl)amide-p-tert-butylthiacalix[4]arene 1a in the cone conformation was synthesized and its binding properties towards a large variety of metal ions were established on the basis of liquid–liquid and solid–liquid extraction as well as complexation experiments. This compound is a less efficient and selective compound than the “classical” tetra(diethyl)amide-p-tert-butylcalix[4]arene 3 in the cone conformation for alkali and alkaline earth metal ions. However, Pb²⁺ is selectively extracted and complexed within heavy and transition metal ions.     

Basicities of alumina-supported alkaline earth metal oxides

A series of alumina-supported alkaline earth metal oxide catalysts were prepared by incipient-wetness impregnation. These catalysts were characterized by nitrogen-sorption to determine their surface areas and pore size distributions. The basicities of these catalysts were characterized by temperature-programmed desorption of carbon dioxide. The TPD results demonstrate that all of the catalysts have one-peak profiles. The basicity increases with increasing atomic number of the alkaline earth metal. The alumina-supported alkaline earth oxides exhibit the same basic properties as bulk metal oxides. However, the presence of alumina can increase the mechanical strength of the catalyst, since the alkaline earth oxides have a weak mechanical strength. The basic properties of the catalysts are strongly influenced by the calcination temperature.     

Surface-treatment of Alkaline Earth Sulfides Based Phosphor

A series of alkaline earth sulfides based phosphors Ca0.8Sr0.2S : Eu^2 , Tm^3 were covered with a layerof protective coating with alkaline earth fluorides by heating the mixture of phosphor and NH4HF2 at elevatedtemperatures. The coatings were characterized by means of XRD and SEM. The optical properties of thecoated phosphors and the influences of the coating on their properties have been discussed extensively. Thestabilities of the coated and uncoated phosphors have been compared.