FI spectrophotometric determination of Pd with DBOK-chlorophosphonazo

A flow injection method was developed for the determination of palladium, based on the reaction of palladium with DBOK-chlorophosphonazo with a detection limit of 0.07 μg/mL and a linear calibration range from 0.1 to 3.2 μg/mL of palladium. The reaction product has a maximum absorption at 630 nm. The method was applied to determine Pd²⁺ in catalysts and in anode mud samples. The relative error is less than 3% and the recovery of palladium is in the range 95% to 105% Received: 27 April 1998 / Revised: 24 August 1998 / Accepted: 26 August 1998     

Modified analcime loaded with zincon as a useful material for the separation and preconcentration of trace palladium and its determination by third-derivative spectrophotometry

This work assesses the potential of natural analcime zeolite as a sorbent for the preconcentration of palladium. Palladium is quantitatively retained on modified analcime zeolite loaded with zincon using the column method in the pH range from 2.5 to 3.5 at a flow rate of 1 mL/min. The palladium complex was removed from the column with 5.0 mL of dimethylsulfoxide (DMSO) and determined by third-derivative spectrophotometry. The detection limit is 0.03 μg/mL (signal-to-noise ratio = 3) in the final solution. Since it is possible to retain 0.15 μg of palladium from 600 mL of solution passing through the column, elution with 5.0 mL of DMSO gives a detection limit of 0.25 ng/mL for palladium in the initial aqueous solution. The calibration curve is linear over the range 0.1 to 5.0 μg/mL of palladium(II) in the final solution with a correlation coefficient of 0.9996. Seven replicated determinations of 5.0 μg of palladium in 5.0 mL dimethylsulfoxide gave a mean d ³ A/dλ³ (peak-to-peak signal between λ₂ = 625 and λ₁ = 654 nm) of 0.64 with a relative standard deviation of 1.2%. The sensitivity of the method (d ³ A/dλ³) is 0.5843 mL/μg of palladium(II) from the slope of the calibration curve. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the determination of trace palladium in various synthetic and water samples. The text was submitted by the authors in English.     

Sensitive reaction rate method for the determination of low levels of formaldehyde with photometric detection

A simple and rapid method is proposed for the determination of ultra trace amounts of formaldehyde. It is based on the catalytic effect of formaldehyde on the oxidation of Brilliant cresyl blue by bromate. The reaction is monitored photometrically by measuring the decrease in absorbance of the dye. Formaldehyde in the range of 0.005–2.300 μg/mL can be determined with a limit of detection of 0.003 μg/mL. The relative standard deviation for ten replicate measurements of 1.5 μg/mL formaldehyde is 0.1%. The method was used for the determination of formaldehyde in real samples with satisfactory results. Received: 26 May 1998 / Revised: 30 September 1998 / Accepted: 3 October 1998     

Validation of a high-performance chromatographic method for determination of cefotaxime in biological samples

An analytical method for detecting and quantifying cefotaxime in plasma and several tissues is described. The method was developed and validated using plasma and tissues of rats. The samples were analyzed by reversed phase liquid chromatography (HPLC) with UV detection (254 nm). Calibration graphs showed a linear correlation (r > 0.999) over the concentration ranges of 0.5–200 μg/mL and 1.25–25 μg/g for plasma and tissues, respectively. The recovery of cefotaxime from plasma standards prepared at the concentrations of 25 μg/mL and 100 μg/mL was 98.5 ± 3.5% and 101.8 ± 2.2%, respectively. The recovery of cefotaxime from tissue standards of liver, fat and muscle, prepared at the concentration of 10 μg/g was: 89.8 ± 1.2% (liver), 103.9 ± 6.5% (fat) and 97.8 ± 2.1% (muscle). The detection (LOD) and quantitation (LOQ) limits for plasma samples were established at 0.11 μg/mL and 0.49 μg/mL, respectively. The values of these limits for tissues samples were approximately 2.5 times higher: 0.3 μg/g (LOD) and 1.25 μg/g (LOQ). For plasma samples, the deviation of the observed concentration from the nominal concentration was less than 5% and the coefficient of variation for within-day and between-day assays was less than 6% and 12%, respectively. The method was used in a pharmacokinetic study of cefotaxime in the rat and the mean values of the pharmacokinetic parameters are given. Received: 25 May 1998 / Revised: 27 July 1998 / Accepted: 1 August 1998     

FIA determination of pyruvate in serum based on direct chemiluminescence oxidation

Chemiluminescence was observed by mixing acidic potassium permanganate solution with pyruvate in the presence of quinine. A new simplified method for pyruvate determination based on this phenomenon was established. The chemiluminescence intensity is a linear function of the concentration of pyruvate in the range of 2 × 10^–6 to 1 × 10^–3 g/mL with a detection limit of 0.8 μg/mL and a relative standard deviation of less than 2.3%. The method has been successfully used to determine pyruvate in serum. Received: 3 April 1998 / Revised: 20 July 1998 / Accepted: 17 September 1998     

Catalytic kinetic spectrophotometric determination of trace amounts of palladium with dahlia violet after separation and preconcentration on sulphydryl dextran gel

A sensitive and selective kinetic catalytic spectrophotometric method has been described for the determination of trace amounts of palladium(II). The method is based on the catalytic effects of palladium(II) on the reduction reactions of Dahlia Violet with sodium dihydrogen hypophosphite (NaH₂PO₂) in a sulfuric acid medium. Under optimal conditions, trace amounts of palladium(II) can be determined. A good linear range has been obtained in the concentration range of Pd(II) over 0.001–0.028 μg/mL with a detection limit of 5.9 × 10⁻¹⁰ g/mL. The method has been successfully applied to the determination of palladium(II) in ore and soil samples. The relative standard deviation was less than 5.0% (n = 11). The coexisting ions were eliminated by preconcentration and separation on sulphydryl dextran gel with satisfactory results. The text was submitted by the authors in English.     

Determination of carbaryl in foods by solid-phase room-temperature phosphorimetry

A phosphorimetric solid phase assay is proposed for the determination of the pesticide carbaryl (CBL) at room temperature. CBL was spotted on filter paper together with Tl(I) as heavy metal, and dried for 3 min, after which the diffuse transmitted phosphorescence was measured using two quartz plates to avoid the quenching effect produced by atmospheric oxygen. The linear dynamic range was 0.5–4.0 μg/mL and the detection and quantification limits were 0.09 and 0.31 μg/mL, respectively. The precision of the method, expressed as relative standard deviation, was 2.3% for a sample containing 2.0 μg/mL of CBL. The method was applied to the determination of CBL residues in cereals, potatoes and waters, obtaining recoveries ranging between 92 and 105%. Received: 10 October 1997 / Revised: 2 February 1998 / Accepted: 7 February 1998     

Flow injection spectrophotometric determination of ultra trace amounts of oxalic acid

A new simple, sensitive and rapid catalytic-spectrophotometric method for the determination of oxalic acid has been described based on its catalytic effect on the redox reaction between dichromate and Brilliant cresyl blue in acidic media by means of a flow injection analysis method. The color change of Brilliant cresyl blue due to its oxidation was monitored spectrophotometrically at 625 nm. The calibration graph was linear in the range of 0.020–4.70 μg/mL oxalic acid with a limit of detection 0.005 μg/mL of oxalic acid. The relative standard deviation for ten replicate measurements of 0.020 μg/mL and 0.900 μg/mL was 2.2% and 1.7%, respectively. No serious interference was identified. Oxalic acid was determined in wastewater and in spinach by the proposed method with satisfactory results. Received: 28 October 1999 / Revised: 13 January 2000 / /Accepted: 20 January 2000     

Development of spectrofluorimetric methods for the determination of levosulpiride in pharmaceutical formulation

Simple, accurate, rapid, and sensitive spectrofluorimetric methods for the determination of levosulpiride in pharmaceutical formulation were developed utilizing its fluorescence reaction with Fe³⁺ (method A) and Al³⁺ (method B). The calibration curves were found to be linear in the concentration range 0.239–3.44 μg/mL and 0.310–2.730 μg/mL with limit of detection 0.005 μg/mL and 0.0032 μg/mL, respectively, for method A and method B. The reaction conditions were studied and optimized. In addition, the complexation of Mg²⁺ and Ca²⁺ was also studied. In all cases, an enhancement in fluorescence emission of levosulpiride upon formation of complex with metal ions was observed. A 2: 1 (drug: metal) stoichiometry for all the complexes was established. Benesi-Hildebrand method was applied for calculation of association constant at 25 and 35°C. The thermodynamic parameters obtained in this study revealed that the interaction process was spontaneous and mainly ΔS-driven.     

Flame atomic absorption spectrometric determination of trace amounts of palladium,gold and nickel after cloud point extraction

In this article, a sensitive cloud point extraction procedure for the preconcentration of trace amounts of palladium, gold and nickel prior to their determination by flame atomic absorption spectrometry has been developed. The cloud point extraction method is based on the complexation of Pd(II), Au(II), and Ni(II) ions with 1-(2-pyridylazo)-2-naphthol and entrapping in non-ionic surfactant Triton X-114. The main factors affecting cloud point extraction efficiency, such as pH of sample solution, concentration of 1-(2-pyridylazo)-2-naphthol and Triton X-114, equilibration temperature and time, were investigated in detail. Under the optimized conditions, calibration curves were constructed for the determination of palladium, gold and nickel according to the general procedure. Linearity was maintained from 0.01 to 1.0 μg/mL for palladium, 10.0 μg/mL to 1.5 μg/mL for gold, and 10.0 μg/mL to 0.5 μg/mL for nickel. Detection limits based on three times the standard deviation of the blank divided by the slope of analytical curve (3Sb/m) for Pd(II), Au(III), and Ni(11) ions were 3.4, 3.9, and 2.4 μg/mL, respectively. Seven replicate determination of a mixture of 0.5 μg/mL palladium and gold and 0.2 μg/mL nickel gave a mean absorbance of 0.174, 0.150, and 0.201 with relative standard deviation ±1.5, ±1.3, and ±1.8%, respectively. The high efficiency of cloud point extraction to carry out the determination of analytes in complex matrices was demonstrated. The proposed method has been applied for determination of trace amount of palladium, gold and nickel in certified reference material and water samples with satisfactory results.     

Sequential injection technique for determination of phenoxybenzamine hydrochloride and metoclopramide in pharmaceutical formulations

A sequential injection analysis (SIA) system is described for the determination of phenoxybenzamine hydrochloride and metoclopramide using spectrophotometer as detector. The method is based on the detection of an unstable red intermediate compound resulting from the reaction of phenoxybenzamine hydrochloride or metoclopramide with the diazotizating product of p-phenylenediamine with sodium nitrite in hydrochloric acid medium. The sampling frequency is 69 h⁻¹ and 75 h⁻¹ for phenoxybenzamine hydrochloride and metoclopramide, respectively. The linear range is 10–400 μg/mL for phenoxybenzamine hydrochloride with a detection limit of 0.081 μg/mL and 20–250 μg/mL for metoclopramide with a detection limit of 0.034 μg/mL. The RSD is 1.01 and 0.45% for phenoxybenzamine hydrochloride and metoclopramide, respectively. The proposed methods were used to determine phenoxybenzamine hydrochloride and metoclopramide in pharmaceuticals. The results are compared with those obtained by pharmacopoeia method. The article is published in the original.     

Liquid-chromatographic determination of sulfadimidine in milk and eggs

A method for the determination/identification of residual sulfadimidine (SDD) in milk and eggs by high-performance liquid chromatography (HPLC) with a photo-diode array detector was developed. The sample preparation was performed by shaking with a mixture of 20% (w/v) trichloroacetic acid-methanol (4:1, v/v) followed by ultra-filtration using Molcut II^?. A LiChrospher^? 100 RP-8 (e) column and a mobile phase of 4% (v/v) acetic acid solution-acetonitrile (6:4, v/v) were used. The average recoveries from spiked SDD samples were 80.8–88.0% with coefficients of variation of 2.8–5.5%. The limits of detection in milk and eggs were 0.01 μg/mL and 0.01 μg/g, respectively. The total time required for the analysis of one sample was less than 20 min. Received: 7 October 1998 / Revised: 29 December 1998 / Accepted: 30 December 1998     

Polarographic determination of cyanide as nickelcyano complex in blood plasma after selective extraction in a methylene blue impregnated polyethylene column

A method for the determination of cyanide in blood plasma by differential pulse polarography (DPP) is described without a drastic acidification of the sample. Cyanide was determined as tetracyanonickelate(II)-anion complex after a microwave-acid assisted cleanup and a selective complex extraction in a polyethylene methylene blue (PE-MB) impregnated column. The cyano complex was eluted from the column with water/acetonitrile and determined by pulse-polarography at –380 mV (Ag/AgCl). The linear range of calibration was obtained from 1.2 to 9.6 μg of cyanide with r = 0.99 and RSD = 9% of 1.2 μg of cyanide. A detection limit of 40 μg L^–1 was calculated and the recoveries of cyanide from spiked samples were about 80%. This method was compared with the classical pyridine-pyrazolone method. Received: 3 September 1997 / Revised: 21 January 1998 / Accepted: 24 January 1998     

Supercritical fluid extraction combined with solid phase extraction as sample preparation technique for the analysis of β-blockers in serum and urine

A method is developed for the determination of β-blockers in serum and urine at levels of 0.5 μg/mL. The technique uses a combination of solid phase extraction (SPE) with in situ derivatization and supercritical fluid extraction (SFE) with subsequent gas chromatography mass spectrometry. The optimization of the SFE step shows that a static extraction period can be eliminated. The method gives good linearity (r = 0.991–0.999) and repeatability in the concentration range of 0.5 to 5 μg/mL. Relative standard deviations for oxprenolol, propanolol and metoprolol were less than 5% in serum and 5–11% in urine. Received: 23 May 1997 / Revised: 28 July 1997 / Accepted: 5 August 1997     

Determination of cyanides in electroplating solutions as Ni(CN)42– and analysis by capillary electrophoresis

A CE method was developed for the determination of total (free and weakly bound) cyanide in electroplating solutions based on the use of a cationic surfactant (TTAB) and complexation with Ni(II)-NH₃ solutions to Ni(CN)₄ ^2–. Both direct complexation and cyanide distillation combined with complexation were tested. Under optimized conditions, this method is time-saving compared to standard methods. Total cyanide determined by CE had detection limits (with respect to the initial sample concentration) of 0.5 μg/mL for direct complexation and 50 ng/mL for distillation combined with complexation. Total cyanide and cyanide not amenable by chlorination (CNAC) were determined in real samples from spent electroplating baths. Received: 5 February 1998 / Revised: 26 July 1998 / Accepted: 1 August 1998     

Flow injection-solid phase spectrofluorimetric determination of pyridoxine in presence of group B-vitamins

A flow-through optosensor has been prepared for the sensitive and selective determination of pyridoxine (vitamin B₆) in aqueous solutions. The sensor was developed in conjunction with a monochannel flow-injection analysis system with fluorimetric detection using Sephadex SP-C25 resin as an active sorbent substrate. This method of determination is carried out without any derivatization. The wavelengths of excitation and emission were 295 and 385 nm, respectively. When a HCl (10^–3 mol L^–1) / NaCl (3 × 10^–2 mol L^–1) solution is used as carrier solution, the sensor responds linearly in the measuring range of 5–200, 10–400 and 50–1800 ng mL^–1 with detection limits of 0.33, 0.67, and 5.70 ng mL^–1 for 2000, 1000 and 200 μL of sample volume, respectively. The relative standard deviation for ten independent determinations is less than 0.75% for 0.2 and 1.0 mL of sample volumes used, and 1.31% for 2.0 mL of sample volume used. The method was satisfactorily applied to the determination of vitamin B₆ in pharmaceutical preparations. Received: 4 June 1998 / Revised: 16 July 1998 / Accepted: 6 August 1998     

Flow injection chemiluminescence determination of isoniazid with electrogenerated hypochlorite

A flow-injection chemiluminescence method for the determination of isoniazid based on the sensitizing effect of isoniazid on the chemiluminescence generating luminol-hypochlorite reaction is described. The hypochlorite was electrogenerated on-line by constant current electrolysis, thus, eliminating instability of hypochlorite solution prepared from commercially available sodium hypochlorite. The calibration graph is linear in the range 1 × 10^–8 to 1 × 10^–6 g mL^–1, and the detection limit is 6 × 10^–9 g mL^–1. The relative standard deviation for determination of 5 × 10^–8 g mL^–1 is 2.8%. The proposed method has been successfully applied to the determination of isoniazid in pharmaceutical preparations. Reveived: 2 May 1998 / Revised: 27 July 1998 / Accepted: 7 August 1998     

Spectrophotometric determination of palladium(II) based on its catalytic effect on the reduction of azure I by sodium hypophosphite

A catalytic-spectrophotometric method for the determination of traces of palladium(II) is proposed. The reaction is based on the catalytic action of palladium(II) on the reduction of azure I (λ_max = 647 nm) by sodium hypophosphite. The various variables affecting the sensitivity were studied, and a study of interfering ions was also carried out. The reaction gave a detection limit of 4.3 ng/mL palladium(II) and good reproducibility with a relative standard deviation of 1.53–1.98% in the palladium(II) concentration range 40–200 ng/mL. The method yielded another linear range (5–40 ng/mL) when using slightly different conditions. In this case, the detection limit was 0.78 ng/mL palladium(II), and the relative standard deviation for ten replicate analyses of 20 ng/mL palladium(II) was 2.05%. The method was applied to the determination of palladium in a sample of activated charcoal. The text was submitted by the authors in English.     

Sequential injection technique for the determination of chlorpromazine hydrochloride in pure form and pharmaceutical formulations

A simple, economical, and automated spectrophotometric method for the determination of chlorpromazine hydrochloride by sequential injection analysis using ammonium metavanadate as colorimetric reagent is proposed. The various chemical and physical conditions that affected the reaction have been thoroughly investigated. The calibration curve was linear within the range 10–100 μg/mL. The detection limit (S/N = 3) was 0.7 μg/mL and the limit of quantification (S/N = 10) was 2.3 μg/mL. The sampling frequency was 22 h⁻¹. The method has been used for the determination of chlorpromazine hydrochloride in pure form and pharmaceutical formulations. The t-test has revealed that there is no evidence of significant differences between the obtained results at the 95% confidence level. The method can be applied to the quantitative determination of chlorpromazine hydrochloride. It is also applicable in the quality control of chlorpromazine hydrochloride preparations. The text was submitted by the authors in English.     

Development and validation of an HPLC-UV method for the simultaneous quantification of carbamazepine, oxcarbazepine, eslicarbazepine acetate and their main metabolites in human plasma

For the first time, a simple, selective and accurate high-performance liquid chromatography method with ultraviolet detection was developed and validated to quantify simultaneously three structurally related antiepileptic drugs; carbamazepine, oxcarbazepine, and the recently launched eslicarbazepine acetate and their main metabolites, carbamazepine-10,11-epoxide, 10,11-trans-dihydroxy-10,11-dihydro-carbamazepine, and licarbazepine. The method involves a solid-phase extraction and a reverse-phase C18 column with 5 cm length. The mobile phase consisting of water, methanol, and acetonitrile in the ratio 64:30:6 was selected as the best one and pumped at 1 mL/min at 40 °C. The use of this recent column and an aqueous mobile phase instead of buffers gives several advantages over the method herein developed; namely the fact that the chromatographic analysis takes only 9 min. The method was validated according to the guidelines of the Food and Drug Administration, showing to be accurate (bias within ±12%), precise (coefficient variation <9%), selective and linear (r ² > 0.997) over the concentration range of 0.05–30 μg/mL for carbamazepine; 0.05–20 μg/mL for oxcarbazepine; 0.15–4 μg/mL for eslicarbazepine acetate; 0.1–30 μg/mL for carbamazepine-10,11-epoxide; 0.1–10 μg/mL for 10,11-trans-dihydroxy-10,11-dihydro-carbamazepine, and 0.1–60 μg/mL for licarbazepine. It was also shown that this method can adequately be used for the therapeutic drug monitoring of the considered antiepileptic drugs, carbamazepine, oxcarbazepine, eslicarazepine acetate, and their metabolites.