磁性壳聚糖/Fe3O4/氧化石墨烯吸附剂的制备及其多染料吸附性能

为了提高壳聚糖的多染料吸附性能并使其便于固液分离,采用共沉淀法制备了壳聚糖、磁铁矿纳米颗粒、氧化石墨烯复合磁性吸附剂(CS/Fe₃O₄/GO)。系统的结构表征显示,CS包覆的Fe₃O₄磁性纳米颗粒均匀地分布在GO的表面。CS/Fe₃O₄/GO具有高达42.5 emu·g^-1的室温铁磁性,因此可在外加磁场中实现高效固液分离。研究表明,CS/Fe₃O₄/GO对亚甲基蓝(MB)、甲基橙(MO)和刚果红(CR)等多种染料具有良好的吸附性能,溶液的pH、初始浓度和吸附时间对其多染料吸附性能具有显著影响。在最佳条件下,CS/Fe₃O₄/GO对MB、MO和CR的吸附量分别达到210.6、258.6和308.9 mg·g^-1。CS/Fe₃O₄/GO具有优异的循环利用性能,经5次循环后仍能保留90%以上的原始吸附量。采用吸附等温线和吸附动力学对CS/Fe₃O₄/GO的多染料吸附性能进行了拟合分析,并详细讨论了其吸附机理。     

石墨烯/硫复合正极材料的一步水热法制备与电化学性能

将硫代硫酸钠（Na₂S₂O₃）与氧化石墨烯（GO）的混合溶液,在酸性条件下经过一步水热反应制备还原氧化石墨烯/硫（RGO/S）复合正极材料. 实验探索了水热温度、反应时间、碳硫质量比例对材料的影响. 通过X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）和恒电流充放电对材料进行分析. 结果表明在180 ℃下,碳硫质量比为3：7时,水热12 h得到的RGO/S复合材料具有优异的循环性能,首次放电比容量为931 mAh·g^-1,50次循环之后其比容量还保持在828.16 mAh·g^-1;RGO/S复合材料的充放电库仑效率在95%以上;同时RGO/S复合材料的倍率性能相比于单质硫有很大提高. 一步水热法能够使硫分子均匀分布在石墨烯片层结构中,同时加强了石墨烯表面基团对硫分子的固定作用.     

ZnCr双金属层状材料对废水中酸性红14的吸附性能

采用共沉淀法制备性能优异的层状材料锌铬水滑石(Zn_xCr-LDHs, x=2, 3, 4), 并探究各种因素对吸附酸性红14(AR14)的影响。XRD、ICP、FTIR及BET表征结果表明:合成的Zn_xCr-LDHs晶型良好且稳定, 具备介孔结构。实验结果表明:最佳吸附剂为Zn₃Cr-LDHs, 比表面积为101 m²·g^-1, 对AR14的最大吸附容量为484.63 mg·g^-1。同时, 降低溶液pH值和提高溶液温度均可促进AR14的吸附。该吸附过程分别符合准二级动力学模型和Freundlich等温吸附模型。结合Materials Studio 5.5软件模拟, 推测该吸附机理主要以表面吸附为主, -SO₃^-基团是反应点。     

ZnCr双金属层状材料对废水中酸性红14的吸附性能

采用共沉淀法制备性能优异的层状材料锌铬水滑石(Zn_xCr-LDHs, x=2, 3, 4), 并探究各种因素对吸附酸性红14(AR14)的影响。XRD、ICP、FTIR及BET表征结果表明：合成的Zn_xCr-LDHs晶型良好且稳定, 具备介孔结构。实验结果表明：最佳吸附剂为Zn₃Cr-LDHs, 比表面积为101 m²·g^-1, 对AR14的最大吸附容量为484.63 mg·g^-1。同时, 降低溶液pH值和提高溶液温度均可促进AR14的吸附。该吸附过程分别符合准二级动力学模型和Freundlich等温吸附模型。结合Materials Studio 5.5软件模拟, 推测该吸附机理主要以表面吸附为主, -SO₃^-基团是反应点。     

聚乙烯亚胺改性氧化石墨对水中Cr(Ⅵ)的吸附

通过对石墨氧化、酯化,将聚乙烯亚胺耦合接枝到氧化石墨表面,制备聚乙烯亚胺改性氧化石墨(PEI-GO).通过FTIR、XRD、TEM、RS和XPS等对合成材料进行表征,并研究了其对水中的Cr(Ⅵ)吸附和脱附性能.表征结果表明,聚乙烯亚胺成功嫁接到氧化石墨上,其氨基含量为4.36 mmol·g^-1.PEI-GO对水中Cr(Ⅵ)具有很好的吸附性能,吸附等温线符合Freundlich方程,吸附动力学可用拟二级动力学方程来描述.PEI-GO对水中Cr(Ⅵ)的吸附随pH的升高而降低.阴离子的存在降低吸附剂对Cr(Ⅵ)的吸附,不同阴离子的影响大小顺序为PO₄^3- >SO₄^2- >NO^3- >Cl^-.XPS结果表明,PEI-GO对Cr(Ⅵ)的去除是吸附-化学还原耦合作用的结果.经4次脱附再生循环,PEI-GO对Cr(VI)仍具有较高吸附量,表明该吸附剂再生性好,可循环使用.     

聚乙烯亚胺改性氧化石墨对水中Cr(Ⅵ)的吸附

通过对石墨氧化、酯化,将聚乙烯亚胺耦合接枝到氧化石墨表面,制备聚乙烯亚胺改性氧化石墨(PEI-GO)。通过FTIR、XRD、TEM、RS和XPS等对合成材料进行表征,并研究了其对水中的Cr(Ⅵ)吸附和脱附性能。表征结果表明,聚乙烯亚胺成功嫁接到氧化石墨上,其氨基含量为4.36mmol·g^-1。PEI-GO对水中Cr(Ⅵ)具有很好的吸附性能,吸附等温线符合Freundlich方程,吸附动力学可用拟二级动力学方程来描述。PEI-GO对水中Cr(Ⅵ)的吸附随pH的升高而降低。阴离子的存在降低吸附剂对Cr(Ⅵ)的吸附,不同阴离子的影响大小顺序为PO₄^3- >SO₄^2- >NO₃^- >Cl^-。XPS结果表明,PEI-GO对Cr(Ⅵ)的去除是吸附-化学还原耦合作用的结果。经4次脱附再生循环,PEI-GO对Cr(VI)仍具有较高吸附量,表明该吸附剂再生性好,可循环使用。     

氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能

以FeCl₃-甲基橙(MO)为模板, 通过化学原位聚合法成功制备出氧化石墨烯/聚吡咯(GO/PPy)插层复合材料. 采用X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)和透射电镜(TEM)等测试技术对复合材料进行物性表征. 此外, 利用循环伏安、恒电流充放电和交流阻抗测试方法对复合材料在两种不同水系电解液(1 mol·L^-1 Na₂SO₄和1 mol·L^-1 H₂SO₄)中的电化学性能进行了研究. 结果显示: 氧化石墨烯和聚吡咯表现出各自优势并发挥协同作用, 使得GO/PPy插层复合材料在中性和酸性电解液中都显示出可观的比电容. 电流密度为0.5 A·g^-1时, GO/PPy 插层复合材料在Na₂SO₄和H₂SO₄电解液中的比电容分别为449.1 和619.0 F·g^-1, 明显高于纯PPy的比电容. 经过800 次循环稳定性测试后, 两种不同电解液中, 复合材料初始容量的保持率分别为92%和62%. 其中酸性电解液体系中初始容量更大, 而中性溶液中具有更稳定的循环性能.     

改性硅藻土负载亚铁氰化铜复合物的制备及其对Cs+的吸附性能

采用水热法、以氯化铝为铝源对硅藻土(De)进行改性,通过浸渍法将亚铁氰化铜(KCuHCF)纳米颗粒负载于改性De表面,制备出γ-AlOOH/De-KCuHCF和γ-Al₂O₃/De-KCuHCF两种复合吸附剂,对所制备的吸附剂进行了表征,并研究了其对Cs⁺的吸附性能。结果表明,所制备吸附剂具有优异的Cs⁺吸附性能,γ-AlOOH/De-KCuHCF和γ-Al₂O₃/De-KCuHCF最高吸附容量分别可达75.44、84.02 mg·g^-1,γ-Al₂O₃/De-KCuHCF对模拟卤水中Cs⁺的吸附率高达97.55%;以3 mol·L^-1 NH₄NO₃为脱附剂,经3级连续脱附后,γ-Al₂O₃/De-KCuHCF的Cs⁺脱附率可达81.88%,经过5次吸附-脱附循环后仍保持了较高的吸附量。     

螺吡喃功能化UiO-66光响应吸附剂的制备及其性能

将光响应分子甲基螺吡喃SP-CH₃引入UiO-66的非极性孔笼中,构筑吸附活性位可光控调节的光响应吸附剂。SP-CH₃功能化的吸附剂完好保留了载体UiO-66的骨架和孔道结构。以阴离子染料甲基橙为探针,研究了吸附剂在不同光照条件下的吸附和解吸性能。结果表明,经紫外光照后,吸附剂对甲基橙的吸附量为41.99 mg·g^-1,相较于可见光照后样品的吸附量提升57.56%,吸附作用增强;经可见光照后,甲基橙的脱附量为81.6%。本策略通过光照刺激改变UiO-66孔笼中SP-CH₃的构型及表面电荷性质,即对吸附活性位进行光控调节,在不同光照条件下实现对吸附质的高效吸附和有效脱附。     

螺吡喃功能化UiO-66光响应吸附剂的制备及其性能

将光响应分子甲基螺吡喃SP-CH₃引入UiO-66的非极性孔笼中,构筑吸附活性位可光控调节的光响应吸附剂。SP-CH₃功能化的吸附剂完好保留了载体UiO-66的骨架和孔道结构。以阴离子染料甲基橙为探针,研究了吸附剂在不同光照条件下的吸附和解吸性能。结果表明,经紫外光照后,吸附剂对甲基橙的吸附量为41.99 mg·g^-1,相较于可见光照后样品的吸附量提升57.56%,吸附作用增强;经可见光照后,甲基橙的脱附量为81.6%。本策略通过光照刺激改变UiO-66孔笼中SP-CH₃的构型及表面电荷性质,即对吸附活性位进行光控调节,在不同光照条件下实现对吸附质的高效吸附和有效脱附。     

Decontamination of bisphenol A from aqueous solution by graphene adsorption

The decontamination of bisphenol A (BPA) from aqueous solution by graphene adsorption was investigated. The maximum adsorption capacity (q(m)) of graphene for BPA obtained from a Langmuir isotherm was 182 mg/g at 302.15 K, which was among the highest values of BPA adsorption compared with other carbonaceous adsorbents according to the literature. Both π-π interactions and hydrogen bonds might be responsible for the adsorption of BPA on graphene, and the excellent adsorption capacity of graphene was due to its unique sp(2)-hybridized single-atom-layer structure. Therefore, graphene could be regarded as a promising adsorbent for BPA removal in water treatment. The kinetics and isotherm data can be well described by the pseudo-second-order kinetic model and the Langmuir isotherm, respectively. The thermodynamic studies indicated that the adsorption reaction was a spontaneous and exothermic process. Besides, the presence of NaCl in the solution could facilitate the adsorption process, whereas the alkaline pH range and higher temperature of the solution were unfavorable.     

Effective Removal of Nitrotoluene Compounds from Aqueous Solution Using Magnetic-Activated Carbon Nanocomposites (<Emphasis Type="Italic">m</Emphasis>-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@ACCs)

In this study, regular-shaped magnetic-activated carbon nanocomposite (m-Fe₃O₄@ACCs) was synthesized and characterized with X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and the vibrating sample magnetometer (VSM) and was used as adsorbents for the removal of nitrotoluene compounds (NTCs) from water and industrial wastewater. The effective parameters on adsorption process, such as solution pH, shaking speed, contact time, and adsorbent dosage were optimized and the optimum amounts were 7 300 rpm, 10 min, and 1.2 g L^–1, respectively. The contact time and adsorbent dosage are dependent parameters and hence were studied simultaneously. The results showed no significant loss in the adsorption capacity, and the adsorption efficiency of m-Fe₃O₄@ACCs could still be 90% in the 9th cycle. The equilibrium adsorption isotherm followed the Langmuir isotherm model describes the monolayer adsorption of NTCs on m-Fe₃O₄@ACCs, and the maximum adsorption capacities (q_m) for 2-nitrotolouene, 2,6-dinitrotoluene, 2,4-dinitrotoluene, and 3,4-dinitrotoluene were found to be 144.93, 142.86, 166.67, and 153.85 mg g^?l, respectively. The proposed process was successfully applied for the removal of NTCs from tap water and nitration process wastewater.     

Preparation and characterization of L-glutamic acid-functionalized graphene oxide for adsorption of Pb(II)

An efficient adsorbent (L-Glu/GO) was successfully synthesized by the reaction between L-glutamic acid (L-Glu) and graphene oxide (GO). The structure and morphology of this adsorbent were characterized by FTIR, SEM, XRD, and TGA. The SEM result indicated that the adsorbent was a nanomaterial with a size of about 50–400 nm. The adsorption experiments of various heavy ions on L-Glu/GO demonstrated that the adsorption performance of Pb(II) was better than others. Various variables affecting the adsorption of L-Glu/GO for Pb(II) were systematically explored. The experimental results indicated that the maximum adsorption capacity and equilibrium time of Pb(II) on L-Glu/GO were 513.4 mg g^?1 and 40 minute, respectively. The sorption kinetics and isotherm fitted well with the pseudo-second-order model and Langmuir model, respectively. The sorption mainly was a chemical process. Thermodynamic studies revealed that the adsorption was a spontaneous and exothermic process. The adsorbent could be regenerated with HCl solution. Hence, it was suggested that the L-Glu/GO could be applied in the removal of Pb(II) from wastewaters.     

Adsorption properties and mechanism of sepiolite to graphene oxide in aqueous solution

Graphene oxide (GO) is widely used in various fields such as improving the performance of cement-based materials and making composite materials due to its large specific surface area and abundant oxygen-containing functional groups. However, it has also caused water pollution. To remove GO in aqueous solution, sepiolite (SEP) was used to adsorb it. The effects of pH, adsorbent quality, GO concentration, temperature and adsorption time on the ability of SEP to adsorb GO were investigated. The materials were characterized by SAP and laser particle size analyzer, and the adsorption performance and mechanism of SEP for GO were further analyzed by XRD, FTIR, SEM, TEM, XPS, AFM, and Zeta potential microscopic tests. The results showed that: 1) Under the conditions of temperature 303 K, pH = 3, adsorbent mass 30 mg, and initial concentration of GO 100 mg/L, the adsorption effect was the best, and the adsorption rate reached 94.8 %. 2) The adsorption reached equilibrium at 2160 min, and the adsorption process was more in line with the pseudo-second-order adsorption kinetic equation, and the adsorption behavior was controlled by chemical effects. 3) The adsorption of SEP to GO is more consistent with the Langmuir and Temkin adsorption isotherm model, and the reaction is a spontaneous, endothermic, and entropy-increasing process. Experiments showed that SEP had a strong adsorption capacity for GO, which provides a reference for the treatment of toxic GO in aqueous solution and the realization of water ecological protection.     

Removal of Th4+ ions from aqueous solutions by graphene oxide

The removal of Th⁴⁺ ions from aqueous solutions was investigated using single-layer graphene oxide (GO) as a sorbent which was prepared by the modified Hummers’ method through batch adsorption experiments at room temperature. Structural characterizations of the sorbent were also investigated. The influences of the pH value of solution, contact time, sorbent dose, ionic strength, the initial metal ion concentration and temperature on the adsorption of Th⁴⁺ were also investigated. These results indicated that the adsorption of Th⁴⁺ was dependent on the pH and independent on the ionic strength. The sorbent provided significant Th⁴⁺ removal (>98.7 %) at pH 3.0 and the adsorption equilibrium was achieved after only 10 min. The Langmuir adsorption isotherm fit the absorption profile very closely, and indicated that a maximum adsorption capacity of 1.77 mmol g^?1 of GO (411 mg g^?1) after 2 h. The thermodynamic parameters showed that this adsorption process was endothermic and spontaneous. Moreover, the desorption level of Th⁴⁺ from GO, by using 0.1 mol L^?1 H₂SO₄ as a stripping agent, was 84.2 ± 1.2 %, and that of 0.5 mol L^?1 HNO₃ as a stripping agent, was 79.8 ± 3.0 %.     

Synthesis and characterization of <Emphasis Type="Italic">β</Emphasis>-cyclodextrin–carboxymethyl cellulose–graphene oxide composite materials and its application for removal of basic fuchsin

A novel β-cyclodextrin–carboxymethyl cellulose–graphene oxide composite material (β-CD–CMC–GO) was synthesized, and its application as excellent adsorbents was carried out for removal basic fuchsin (BF) in aqueous solution. The structure and morphology of β-CD–CMC–GO composite material were characterized by using FTIR, SEM, TEM, XRD, TG and DSC methods. The composites could remove basic fuchsin from aqueous solution efficiently. The adsorption experiment was carried out and the optimum experimental conditions were ascertained. The highest adsorption efficiency was obtained 97.3% at 0.015 g/mL dosage of β-CD–CMC–GO, the temperature of 25 °C and time of 2.5 h. Adsorption kinetics, adsorption isotherm and adsorption thermodynamic were used to analyze the adsorption system. The experimental data of adsorption kinetics of system were well followed by pseudo-second-order equation. The adsorption isotherm data were fitted using Langmuir isotherm model and Freundlich isotherm model. The maximum adsorption capacity of basic fuchsin reached 58.65 mg/g. The thermodynamic parameters indicated that the adsorption process was spontaneous and exothermic. The adsorbent has excellent regeneration ability and reproducibility. The proposed method shows that the β-CD–CMC–GO could be applied to removal of basic fuchsin in wastewater with satisfactory result.     

Highly efficient removal of diazinon pesticide from aqueous solutions by using coconut shell-modified biochar

This study evaluates the adsorption of diazinon from aqueous solutions onto coconut shell-modified biochar using a batch system. The amount of dosage and initial pH are the main parameters being studied to obtain maximum adsorption capacity of the probe molecules. The carbonized coconut shell biochar (BC1), activated coconut shell biochar (BC2), chemically modified phosphoric acid (BC3) and sodium hydroxide coconut shell biochar (BC4) were prepared and tested as variables in the adsorption experiment. The characteristic of biochar via SEM, EDX and BET analysis revealed the large porous of surface morphology and slight changes in the composition with high surface area (405.97 – 508.07 m²/g) by following the sequence of BC3 > BC2 > BC4. Diazinon removal percentage as high as 98.96% was achieved at pH 7 with BC3 as adsorbent dosing at 5.0 g/L. The high coefficient of determination, R² with a small value of ERRSQ and χ² error analysis present the BC1 (0.9971) and BC2 (0.9999) are best fitted with Freundlich isotherm indicates multilayer sorption onto heterogeneous surface whereby the Langmuir isotherm model is the best fitting is described of monolayer adsorption process onto the homogenous surface of BC3 and BC4. The results indicated the maximum adsorption capacity (q_m) was achieved by BC3 with 10.33 mg/g, followed by BC2 (9.65 mg/g) in accordance to the Langmuir isotherm while Freundlich isotherm showed the highest adsorption capacity (k_F) with 1.73 mg/g (L/mg)^1/n followed by BC4 with 0.63 mg/g (L/mg)^1/n at favorable adsorption isotherm (1 ≤ n ≤ 10). Thus, the results obtained depicted that BC2 and BC3 are highly efficient adsorbents and both exhibit great potential in removing diazinon from aqueous solutions.     

Adsorption characteristics of malachite green dye onto novel kappa-carrageenan-g-polyacrylic acid/TiO2–NH2 hydrogel nanocomposite

Batch adsorption experiments were carried out for the removal of malachite green (MG) cationic dye from aqueous solution using novel hydrogel nanocomposite that was prepared by graft copolymerization of acrylic acid (AA) onto kappa-carrageenan (κC) biopolymer in the presence of a crosslinking agent, a free radical initiator and aminosilica-functionalized TiO₂ nanoparticles (κC-g-PAA/TiO₂–NH₂). The factors influencing adsorption capacity of the adsorbents such as initial pH value (pH₀) of the dye solutions, TiO₂–NH₂ content (wt%), initial concentration of the dye, amount of adsorbents, and temperature were investigated. The adsorption capacity of hydrogel nanocomposite for MG was compared with hydrogel. The adsorption behaviors of both adsorbents showed that the adsorption kinetics and isotherms were in good agreement with a pseudo-second-order equation and the Langmuir equation. The high adsorption capacity (q _m= 666–833 (mg/g)) and the favorable heterogeneity factor (n = 1.2–1.5) calculated from isotherm equations show the efficiency of the novel adsorbents.     

An ultrasensitive lysozyme chemiluminescence biosensor based on surface molecular imprinting using ionic liquid modified magnetic graphene oxide/β-cyclodextrin as supporting material

In this work, ionic liquid modified Fe₃O₄@dopamine/graphene oxide/β-cyclodextrin (ILs-Fe₃O₄@DA/GO/β-CD) was used as supporting material to synthesize surface molecularly imprinted polymer (SMIP) which then was introduced into chemiluminescence (CL) to achieve an ultrasensitive and selective biosensor for determination of lysozyme (Lys). ILs and β-CD was applied to provide multiple binding sites to prepare Lys SMIP and Fe₃O₄@DA was designed to make the product separate easily and prevent the aggregation of GO which could improve absorption capacity for its large specific surface area. The ILs-Fe₃O₄@DA/GO/β-CD-SMIP showed high adsorption capacity (Q = 101 mg/g) to Lys in the adsorption isotherm assays. The adsorption equilibrium was reached within 10 min for all the concentrations, attributing to the binding sites situated exclusively at the surface, and the adsorption model followed Langmuir isotherm. Under the suitable CL conditions, the proposed biosensor could response Lys linearly in the range of 1.0 × 10⁻⁹–8.0 × 10⁻⁸ mg/mL with a detection limit of 3.0 × 10⁻¹⁰ mg/mL. When used in practical samples in determination of Lys, the efficient biosensor exhibited excellent result with the recoveries ranging from 94% to 112%.     

Preparation of ferric nitrate–graphene nanocomposite and its adsorption of arsenic(V) from simulated arsenic‐containing wastewater

Ferric nitrate–graphene (FG) nanocomposites synthesized via the equivalent‐volume impregnation method were used for the removal of As(V) species from simulated arsenic‐containing wastewater. Effects of various factors were assessed, such as the reaction temperature, solution pH, adsorbent dosage, and reaction time. The results indicated that the As(V) removal efficiency was as high as 99%, and the concentration of arsenic‐containing wastewater after FG treatment was as low as 9.4 μg L^–1 as a result of the optimal absorption capacity and maximum specific surface area (171.766 m²/g) of this material. The equilibrium adsorption capacity of FG for As(V) was achieved in approximately 20 min, and the maximum adsorption capacity was calculated to be 112.4 mg g^–1 by Langmuir adsorption isotherm, which was higher than that of other adsorbents such as manganese‐incorporated iron(III) oxide–graphene (14.42 mg g^–1). Moreover, the removal efficiency of As(V) can be maintained above 95% under acidic and alkaline conditions. Brunauer–Emmett–Teller analysis showed that the modified FG pore structure was regular. Based on the characterizations by X‐ray diffraction, X‐ray photoelectron spectroscopy, and Fourier transform infrared, the products on the surface of the used FG were Fe(OH)₃, FeAsO₄, and other compounds, and As(V) was mainly removed by the formation of insoluble compounds and coprecipitation.