Effect of combined changes in delayed extraction time and potential gradient on the mass resolution and ion discrimination in the analysis of polydisperse polymers and polymer blends by delayed extraction matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

Data reported here show that, in the delayed extraction matrix-assisted laser desorption/ionization time-of-flight (DE-MALDI-TOF) mass spectrometric analysis of synthetic polydisperse polymers, different experimental conditions of spectral recording are required to optimize the signal in all the m/z regions of the spectrum. The effect of combined changes in delay time and grid voltage % values on both mass resolution and mass accuracy of DE spectra of a polyethylene glycol sample (PEG(mix), with a well-defined molar distribution of its components) is discussed. The necessity of a compromise between the values of these two parameters is shown. Furthermore, the occurrence of analyte discrimination, which can invalidate the composition analysis especially in the case of polymer blends, is demonstrated. Copyright 1999 John Wiley & Sons, Ltd.     

Characterization of bacterial lipooligosaccharides by delayed extraction matrix-assisted laser desorption ionization time-of-flight mass spectrometry

Matrix-assisted laser desorption ionization (MALDI) with a time-of-flight analyzer has been used to analyze bacterial lipooligosaccharides (LOS). Crude LOS preparations from pathogenic strains of Haemophilus influenzae and Haemophilus ducreyi and a commercial preparation of lipopolysaccharide from Salmonella typhimurium were treated with hydrazine to remove O-linked fatty acids on the lipid A moiety. The resulting O-deacylated LOS forms were water soluble and more amenable to cocrystallization with standard MALDI matrices such as 2,5-dihydroxybenzoic acid and 1-hydroxyisoquinoline. Under continuous extraction conditions, O-deacylated LOS yielded broad peaks with abundant salt adducts as well as forming prompt fragments through β-elimination of phosphoric acid, that is, [M-H₃PO₄-H]. However, when a time delay was used between ionization and extraction (“delayed extraction”) a significant improvement was seen in both mass resolution and the stability of the molecular ions against β-elimination of phosphoric acid, especially in the negative-ion mode. Both an external two-point calibration and an internal single-point calibration were used to assign masses, the latter of which provided the highest degree of accuracy (better than 0.01% in most cases). At higher laser powers, the LOS molecules cleave readily between the oligosaccharide and lipid A moieties yielding a number of prompt fragments. Postsource decay (PSD) analysis of selected molecular ions provided a set of fragments similar to those seen in the linear spectra, although they were more limited in number because they were derived from a single LOS-glycoform. Both the prompt and PSD fragments provided important structural information, especially in assigning the phosphate and phosphoethanolamine substitution pattern of the lipid A and oligosaccharide portions of LOS. Last, with the addition of ethylenediaminetetraacetic acid followed by pulsed sonication, the relatively insoluble (and impure) LOS preparations yielded MALDI spectra similar to the O-deacylated LOS, although these intact LOS preparations required higher laser powers to ionize and were generally more affected by competing impurities.     

Molecular structure of silsesquioxanes determined by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry was used to deduce the three-dimensional structure of a complex silsesquioxane polymer. Four distinct levels of structure were observed in the mass spectrum. The overall shape of the peak distribution was typical of polymers formed by condensation reactions. The mass separation between major clusters of peaks, each major cluster corresponding to an oligomer with a unique number of repeat units, confirmed that the synthesis proceeded as expected with no side reactions. The mass separation between peaks within a major cluster showed that intramolecular reactions during synthesis resulted in the elimination of water. The loss of water was ascribed to the formation of closed loops in the polymer structure. A simple arithmetic algorithm is presented for identifying these peaks. Autocorrelation techniques were used to determine the number and distribution of intramolecular closed loops per oligomer. This knowledge was used to deduce whether a particular oligomer is branched-linear, ladder, polyhedral, or some combination of these. The single-oligomer isotopic distribution was used to determine that cationization was present from both sodium and potassium ions.     

Quantitative analysis of polydisperse systems via solvent-free matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

Quantitative analysis of partially soluble and insoluble polydisperse materials is challenging due to the lack of both appropriate standards and reliable analytical techniques. To this end, matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) incorporating a solvent-free sample preparation technique was investigated for the quantitative analysis of partially soluble, polydisperse, polycyclic aromatic hydrocarbon (PAH) oligomers. Molecular weight standards consisting of narrow molecular weight dimer and trimer oligomers of the starting M-50 petroleum pitch were produced using both dense-gas/supercritical extraction (DGE/SCE) and preparative-scale, gel permeation chromatography (GPC). The validity of a MALDI-based, quantitative analysis technique using solvent-free sample preparation was first demonstrated by applying the method of standard addition to a pitch of known composition. The standard addition method was then applied to the quantitative analysis of two insoluble petroleum pitch fractions of unknown oligomeric compositions, with both the dimer and trimer compositions of these fractions being accurately determined. To our knowledge, this study represents the first successful MALDI application of solvent-free quantitative analysis to insoluble, polydisperse materials.     

Characterization of mesogen-jacketed liquid crystalline polymers by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

For synthetic polymers, a proper sample preparation method is essential for successful characterization by matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry. In this work, six synthetic mesogen-jacketed liquid crystalline polymers (MJLCPs) with different main-chain, spacer and mesogenic units were investigated by MALDI-TOF mass spectrometry. Several factors that affect the analysis of these polymers were examined. These factors include matrices used, cationization salts used, the concentration of polymers, and the ratio of sample to matrix. After testing different conditions, we found a suitable sample preparation method for these six polymers. The number average molecular weight (M(n)), weight average molecular weight (M(w)) and polydispersity (PD) were calculated using data obtained in the linear mode. The end groups of the polymers were proposed using data obtained in reflectron mode. Copyright 2000 John Wiley & Sons, Ltd.     

Analysis of the accuracy of determining average molecular weights of narrow polydispersity polymers by matrix-assisted laser desorption ionization time-of-flight mass spectrometry

Matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOFMS) can be used to determine number- and weight-average molecular weights of narrow polydispersity polymers. In this work, several possible sources of error in determining molecular weights of polymers with narrow polydispersity by MALDI-TOFMS are rigorously examined. These include the change in polymer distribution function, broadening or narrowing of the overall distribution, and the truncation of selected oligomer peaks within a distribution (i.e., the oligomer peaks at the high-and low-mass tails expected to be observed are not detected). These variations could be brought about by a limited detection sensitivity, background interference, and/or mass discrimination of oligomer analysis in MALDI-TOFMS. For narrow polydispersity polystyrenes, it is shown that by using an appropriate MALDI matrix and sample preparation protocol and a sensitive ion detection instrument, no systematic errors from these possible variations were detected within the experimental precision (0.5% relative standard deviation) of the MALDI method. It is concluded that MALDI mass spectrometry can provide accurate molecular weight and molecular weight distribution information for narrow polydispersity polymers, at least for polystyrenes examined in this work. The implications of this finding for polymer analysis are discussed.     

Covariance mapping in matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

A novel method for acquisition and numerical analysis of matrix-assisted laser desorption/ionization (MALDI) time-of-flight mass spectral data is described. The digitized ion current transient from each consecutive laser shot is first acquired and stored independently. Subsequently, statistical correlation parameters between all stored transients are computed. We illustrate the uses of this event-by-event analysis method for studies of sample surface heterogeneity as well as for elucidating the mechanisms of ion formation in MALDI. Other potential applications of the method are also outlined.     

Accurate mass measurement of low molecular weight compounds by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

We report the application of matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) for the accurate measurement of mass of low molecular weight compounds (smaller than 1500 Da), a linear peptide, two types of cyclic depsipeptides, a polyhydroxy-macrocyclic lactone, and two prenylated flavonoids, with delayed extraction in the reflector mode. The performance of the MALDI-TOF instrument was less than those of fast atom bombardment and Fourier-transform ion cyclotron resonance mass spectrometry instruments and insufficient to give acceptable accuracy for literature reporting. Nevertheless, when combined with NMR spectrometry and/or amino acid analysis to give information on the numbers of carbon atoms and index of hydrogen deficiency, MALDI was useful for determination of the elemental composition of the low molecular weight compounds available in small quantities.     

Analysis of solid-supported oligonucleotides by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

This study presents matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) as a powerful tool to analyze and characterize oligonucleotides covalently linked to a solid support during their synthesis. The analysis of the fragment ions generated either in negative or positive mode allows direct and easy access to the nucleotide sequence and identification of the internucleosidic linkage. The mechanisms of the fragmentation of the solid-supported oligonucleotides induced by MALDI-TOFMS are discussed. Copyright 2000 John Wiley & Sons, Ltd.     

Analysis of plant phosphatidylcholines by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

The use of matrix-assisted laser desorption/ionization (MALDI) time-of-flight (TOF) mass spectrometry (MS) for the quantitative determination of phospholipid (PL) molecular species has been problematic, due primarily to the formation of multiple signals (corresponding to the molecular ion and other adducts) for some classes of PL. For example, analysis of phosphatidylcholine (PC) yielded signals that corresponded to protonated and sodiated molecules in the MALDI spectrum. The resulting spectral overlap among various molecular species (e.g. [PC(16:0/18:2) + Na] and [PC(18:2/18:3)]) made it impossible to ascertain their relative amounts using this technique. Other spectral ambiguities existed among different structural isomers, such as PC(18:1/18:1) and PC(18:0/18:2). We determined that molecular species could be resolved by MALDI-TOFMS by first removing the polar head (e.g. phosphocholine) from the phospholipid to effect production of only the sodiated molecules of the corresponding diacylglycerols (DAGs). Analysis of the resulting spectrum allowed unequivocal determination of the molecular species profile of PC from potato tuber and soybean. Estimation of fatty acid composition based on the molecular species determined by MALDI-TOFMS analysis agreed with that from GC-FID analysis. Post-source decay (PSD) was used to resolve standard isomers of PC (e.g. 18:1/18:1 vs. 18:0/18:2). Our results indicated that PSD is a useful approach for resolving structural isomers of PL molecular species.     

Characterization of humic substances by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) and laser desorption/ionization (LDI-)TOFMS have been used to characterize Suwannee River humic substances, obtained from the International Humic Substances Society (IHSS), and Armadale soil fulvic acid (ASFA). An array of MALDI matrices were tested for use with humic substances, including alpha-cyano-4-hydroxycinammic acid (CHCA), 2-(4-hydroxyphenylazo)benzoic acid (HABA), 2,5-dihydroxybenzoic acid (DHBA), sinapinic acid, dithranol and norharmane. DHBA yielded the best results, exhibiting superior ionization efficiency, low noise, broad applicability to the analytes of interest, and most importantly producing an abundance of high mass ions, the highest observed being m/z 1848. A number of sample preparation modes were investigated; the overlayer method improved sample/matrix homogeneity and hence shot-to-shot reproducibility. The choice of the matrix, mass ratio of analyte to matrix, and the sample preparation protocol, were found to be the most critical factors governing the quality of the mass spectra. Matrix suppression was greatly enhanced by ensuring good mixing of matrix and analyte in the solid phase, proper optimization of the matrix/analyte ratio, and optimizing delayed extraction to ensure complete matrix-analyte reaction in the plume before ions are moved to the flight tube. A number of common features, in particular specific ions which could not be attributed to the matrices or to contaminants, were present in the spectra of all the humic substances, regardless of origin or operational definition. Additionally, a prominent repeating pattern of peaks separated by 55, 114 and 169 Da was clearly observed in both LDI and MALDI, suggesting that the humic compounds studied here may have quasi-polymeric or oligomeric features.     

Characterization of Aspergillus spores by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

The intact fungal spores of several strains of four Aspergillus species, Aspergillus flavus, A. oryzae, A. parasiticus, and A. sojae, were directly analyzed by matrix-assisted laser desorption/ionization (MALDI) time-of-flight mass spectrometry. Very simple MALDI mass spectra are obtained by directly mixing spores with a matrix such as alpha-cyano-4-hydroxycinnamic acid or sinapinic acid. The mass spectra are obtained from the ablation of cell walls of spores owing to the acidity of the matrix solution. The MALDI results show that aflatoxigenic strains and non-aflatoxigenic strains have different mass peak profiles. Furthermore, the MALDI results of non-aflatoxigenic A. flavus and A. parasiticus spores resemble those of the closely related A. oryzae and A. sojae spores, respectively.     

Intact protein analysis by matrix-assisted laser desorption/ionization tandem time-of-flight mass spectrometry

Direct tandem mass spectrometric (MS/MS) analysis of small, singly charged protein ions by tandem time-of-flight mass spectrometry (TOFMS) is demonstrated for proteins up to a molecular mass of 12 kDa. The MALDI-generated singly charged precursor ions predominantly yield product ions resulting from metastable fragmentation at aspartyl and prolyl residues. Additional series of C-terminal sequence ions provide in some cases sufficient information for protein identification. The amount of sample required to obtain good quality spectra is in the high femtomolar to low picomolar range. Within this range, MALDI-MS/MS using TOF/TOF trade mark ion optics now provides the opportunity for direct protein identification and partial characterization without prior enzymatic hydrolysis.     

Evaluation of mass discrimination effects in the quantitative analysis of polydisperse polymers by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry using uniform oligostyrenes

Mass discrimination effects in matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) were quantitatively investigated using equiweight and equimolar mixtures of uniform polystyrene (PS) oligomers. Uniform PS oligomers were separated by preparative super-critical fluid chromatography (SFC) from commercial standard PS samples. The separated PS oligomers, with degrees of polymerization n = 2–25, have absolutely no molecular weight distributions. Equiweight and equimolar mixtures of uniform PS oligomers were accurately prepared by weighing by microbalance, and their spectra were recorded using a MALDI-TOF mass spectrometer. In the lower molecular weight region (less than about 10³) the oligomers with lower molecular weights give lower mass spectral intensities, with no correlation with laser power. In contrast, higher laser powers yield a decrease of mass spectral intensities in the higher molecular weight region. These results clearly show that mass discrimination effects occur at lower and higher molecular weights depending on the laser power, and provide quantitative information about the discrimination. Using the data on equiweight and equimolar mixtures of PS oligomers, it was possible to calibrate the MALDI-TOF mass spectral data for an analysis of molecular weight distribution of a standard monodisperse PS sample with number-averaged molecular weight of 10³, and to compare it with the molecular weight distribution measured by analytical SFC. The result from the calibrated MALDI-TOF mass spectrum, however, does not agree perfectly with that from the SFC results, because undetectable peaks in MALDI-TOF mass spectra at lower and higher molecular weights could not be included in the calibration of peak intensities. Copyright © 2001 John Wiley & Sons, Ltd.     

Protein secondary structure and stability determined by combining exoproteolysis and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

In the post-genomic era, several projects focused on the massive experimental resolution of the three-dimensional structures of all the proteins of different organisms have been initiated. Simultaneously, significant progress has been made in the ab initio prediction of protein three-dimensional structure. One of the keys to the success of such a prediction is the use of local information (i.e. secondary structure). Here we describe a new limited proteolysis methodology, based on the use of unspecific exoproteases coupled with matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS), to map quickly secondary structure elements of a protein from both ends, the N- and C-termini. We show that the proteolytic patterns (mass spectra series) obtained can be interpreted in the light of the conformation and local stability of the analyzed proteins, a direct correlation being observed between the predicted and the experimentally derived protein secondary structure. Further, this methodology can be easily applied to check rapidly the folding state of a protein and characterize mutational effects on protein conformation and stability. Moreover, given global stability information, this methodology allows one to locate the protein regions of increased or decreased conformational stability. All of this can be done with a small fraction of the amount of protein required by most of the other methods for conformational analysis. Thus limited exoproteolysis, together with MALDI-TOF MS, can be a useful tool to achieve quickly the elucidation of protein structure and stability.     

Quantitation of synthetic polymers using an internal standard by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

MALDI-TOF MS is utilized to perform quantitative analysis on synthetic polymers. Despite the inherent limitations of MALDI, good quantitative results have been obtained in the three sets of experiments described here. An internal standard with similar molecular properties as the analytes is introduced. Plots of relative integrated intensity ratios as a function of theoretical ratios of stoichiometry are drawn based on the results. The satisfactory slopes and correlation coefficients illustrated the practicality of quantitative measurement by MALDI-TOF MS.     

Detection of benzopyrene-deoxyguanosine adducts by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

A method for the detection of BPDE-d guanosine adducts using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) is described and illustrated. The results indicate that MALDI is capable of detecting two other DNA benzopyrene adducts, which are trace products formed during the synthesis of BPDE-d guanosine. This MALDI-TOFMS method offers the potential for the detection of DNA adducts in human tissue using very limited sample purification and preparation.     

Identification of isoenzymes using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

The identification of isoforms is one of the great challenges in proteomics due to the large number of identical amino acids preventing their separations by two-dimensional electrophoresis. Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) has become a rapid and sensitive tool in proteomics, notably with the new instrumental improvements. In this study, we used several acquisition modes of MALDI-TOFMS to identify isoforms of porcine glutathiones S-transferase. The use of multiple proteases coupled to the different acquisition modes of MALDI-TOFMS (linear, reflectron, post-source decay (PSD) and in-source decay, positive and negative modes) allowed the identification of two sequences. Moreover, a third sequence is pointed out from a PSD study of a tryptic ion revealing the modification of the amino acid tyrosine 146 to phenylalanine.     

Surfactant-mediated matrix-assisted laser desorption/ionization time-of-flight mass spectrometry of small molecules

A variety of surfactants have been tested as matrix-ion suppressors for the analysis of small molecules by matrix-assisted laser desorption/ionization time-of flight mass spectrometry. Their addition to the common matrix alpha-cyano-4-hydroxycinnamic acid (CHCA) greatly reduces the presence of matrix-related ions when added at the appropriate mole ratio of CHCA/surfactant, while still allowing the analyte signal to be observed. A range of cationic quaternary ammonium surfactants, as well as a neutral and anionic surfactant, was tested for the analysis of phenolics, phenolic acids, peptides and caffeine. It was found that the cationic surfactants, particularly cetyltrimethylammonium bromide (CTAB), were suitable for the analysis of acidic analytes. The anionic surfactant, sodium dodecyl sulfate, showed promise for peptide analysis. For trialanine, the detection limit was observed to be in the 100 femtomole range. The final matrix/surfactant mole ratio was a critical parameter for matrix ion suppression and resulting intensity of analyte signal. It was also found that the mass resolution of analytes was improved by 25-75%. Depth profiling of sample spots, by varying the number of laser shots, revealed that the surfactants tend to migrate toward the top of the droplet during crystallization, and that it is likely that the analyte is also enriched in this surface region. Here, higher analyte/surfactant concentration would reduce matrix-matrix interactions (known to be a source of matrix-derived ions).     

Towards a reliable molecular mass determination of intact glycoproteins by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

Different matrices and sample-matrix preparation procedures have been tested in order to study their influence on the matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectra of intact glycoproteins, which present different degrees of glycosylation (human transferrin; bovine fetuin; bovine alpha(1)-acid-glycoprotein; recombinant human erythropoietin; and the novel erythropoiesis stimulating protein). Using sinapinic acid (SA) and the fast evaporation method, the studied glycoproteins became susceptible to fragmentation at any laser intensity, suggesting that this 'hot' matrix is unsuitable for a reliable molecular mass determination of glycosylated compounds. In contrast, 2,5-dihydroxybenzoic acid (DHB) and 6-aza-2-thiothymine (ATT), with an adequate sample-matrix preparation, provided improved results. Samples containing DHB after crystallization by vacuum drying demonstrated the best performance because the labile functional groups from the glycoforms were apparently fragmented to a lower extent. The average molecular masses obtained using this methodology were in all cases a better estimation than those values reported in the literature. The results were reproducible, and sensitivity was similar to that obtained with SA and the fast evaporation method. These excellent results suggest that this MALDI-TOF-MS methodology could be useful for an improved determination of the average molecular mass values of microheterogeneous compounds such as glycoproteins, glycosylated compounds or, in general, molecular mass values of molecules with similar labile functional groups.