Using TiO<Subscript>2</Subscript> supported on Clinoptilolite as a catalyst for photocatalytic degradation of azo dye Disperse yellow 23 in water

In this investigation photocatalytic degradation of azo dye Disperse yellow 23 in water was studied. Titanium (IV) oxide was supported on Clinoptilolite (CP) (Iranian Natural Zeolite) using the solid-state dispersion (SSD) method. The results show that the TiO₂/Clinoptilolite (SSD) is an active photocatalyst. The maximum effect of photo degradation was observed at 10 wt % TiO₂, 90 wt % Clinoptilolite. A first order reaction with k = 0.0119 min^?1 was observed. The effects of some parameters such as pH, amount of photocatalyst, and the initial concentration of dye were examined.     

Photochemical degradation of an anionic surfactant by TiO<Subscript>2</Subscript> nanoparticle doped with C,N in aqueous solution

Novel C,N-doped TiO₂ nanoparticles were prepared by a solid phase reaction. The catalyst was characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). The results showed that crystallite size of synthesized C,N-doped TiO₂ particles were in nanoscale. UV light photocatalytic studies were carried out using sodium naphthalenesulfonate formaldehyde condensate (SNF) as a model pollutant. The effects of initial concentration of surfactant, catalyst amount, pH, addition of oxidant on the reaction rate were ascertained and optimum conditions for maximum degradation was determined. The results indicated that for a solution of 20 mg/L of SNF, almost 98.7% of the substance were removed at pH ~ 4.0 and 0.44 g/L photocatalyst load, with addition of 1 mM K₂S₂O₈ and irradiation time of 90 min. The kinetics of the process was studied, and the photodegradation rate of SNF was found to obey pseudo-first-order kinetics equation represented by the Langmuir–Hinshelwood model.     

Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/BiFeO<Subscript>3</Subscript> heterostructure: preparation,characterization, and photocatalytic activity

Bi₂O₃/BiFeO₃ composite was successfully fabricated by a conventional sol–gel method and structural properties were characterized based on X-ray diffractometer, scanning electron microscope, transmission electron microscope, energy-dispersive X-ray analyzer, nitrogen adsorption–desorption measurement, and UV–visible diffuse reflectance spectroscopy. Bi₂O₃/BiFeO₃ had a good absorption for visible light, which was benefit to photocatalytic activity. The highest degradation efficiency was obtained when the content of Bi₂O₃ in Bi₂O₃/BiFeO₃ was 63.9%. Effect of experimental conditions was investigated, and the highest photocatalytic activity of Bi₂O₃/BiFeO₃ was observed at photocatalyst dosage of 0.5 g/L, initial BPA concentration of 10 mg/L, and solution pH of 6.3. Bi₂O₃/BiFeO₃ photocatalyst exhibited enhanced photocatalytic activity for BPA, and the reaction rate constant over Bi₂O₃/BiFeO₃ composite was 2.23, 3.65, and 8.71 times higher than that of BiFeO₃, Bi₂O₃ and commercial TiO₂ (P25), respectively. Bi₂O₃/BiFeO₃ showed high photocatalytic activity after three cycles, suggesting that it was a stable photocatalyst. The possible photocatalytic mechanism has been discussed on the basis of the theoretical calculation and the experimental results. The hydroxyl and superoxide radicals together with photogenerated holes played significant roles in the photocatalytic reaction.     

Novel,Facile and Swift Technique for Synthesis of CeO<Subscript>2</Subscript> Nanocubes Immobilized on Zeolite for Removal of CR and MO Dye

CeO₂/zeolite nanocomposite was successfully prepared by the mixing-calcination method. The structural characteristics of photocatalyst were investigated by XRD, SEM, TEM and EDX. Photocatalytic degradation experiments were carried out with varying amounts of the CeO₂/zeolite, the ratio of 3:1 (CeO₂/zeolite) was exhibited excellent photocatalytic activity towards dye degradation. Synergistic effect of CeO₂/zeolite played a key role in photocatalytic degradation. The main reactive oxygen species was determined by trapping experiments. Additionally, the recyclability was tested up to the fourth cycle. The CeO₂/zeolite nanocomposite is a promising photocatalyst for removing trace and unprocessed organic contaminants in the industrial dye waste water treatment. The efficiency of CeO₂/zeolite nanocomposite offers a potential economical route to degrade organic contaminants and recovering photocatalyst simultaneously.     

Effect of pretreatment on microstructure and photocatalytic activity of kaolinite/TiO<Subscript>2</Subscript> composite

Kaolinite/TiO₂ composites were prepared by using sol-gel method and raw kaolin, pretreated kaolinite and tetrabutyl titanate as the main raw materials. X-ray diffractometer, field-emission scanning electron microscope and infrared spectrometer analysis were carried out to characterize the phase composition and microstructure of the samples. The photocatalytic performance of the kaolinite/TiO₂ composites were evaluated by degrading the methylene blue (MB) and phenol aqueous solution, respectively. The results show that intercalation and exfoliation reduced the size and thickness of kaolinite particles. Acid treatment improved the distribution and the loading quantity of TiO₂ grains. When the kaolinite/TiO₂ composites were calcined at 500?°C, the tetragonal structure of anatase particles of 30–100?nm in size were obtained, but the exfoliated kaolinite crystals were damaged. The degradation rate of MB increased gradually with the extension of photocatalytic reaction time and the enhancement of photocatalyst dosage. The adsorption performance of acid-treated kaolinite/TiO₂ composite (AKT) was nearly the same as that of raw kaolin/TiO₂ composite (RKT), but that of the exfoliated kaolinite/TiO₂ composite (EKT) was the most excellent. The photocatalytic performance of AKT and EKT were better than that of RKT, and AKT exhibited the optimum property. Under a certain photocatalyst dosage and photocatalysis time, the absorption rate and the degradation rate decreased gradually with the enhancement of initial concentration of MB. Similar result was also acquired for the degradation of phenol. Both the acid treating and the exfoliating to kaolinite enhanced the photocatalytic performance of the kaolinite/TiO₂ composite photocatalysts, but acid treatment may be more helpful to the preparation of high performance kaolinite/TiO₂ composite photocatalyst.

Open image in new window

     

Kinetic studies of direct blue photodegradation over flower-like TiO<Subscript>2</Subscript>

The kinetics of photocatalytic oxidation reaction for direct blue solution was studied by using flower-like TiO₂ under the irradiation of ultraviolet (UV) light. A series of possible affecting factors were studied, including pH value, the additive amount of light catalyst, H₂O₂ and with or without Ag modification. The kinetics of photocatalytic degradation under UV was found following a pseudo-second-order reaction kinetic model with high regression coefficients (R ²). It has been demonstrated that the initial concentration and its related factors have influenced the photocatalytic degradation efficiency and corresponding kinetic parameters. Also, the kinetic parameter k is increasing with the degradation efficiency.     

Assessment of operating parameters for photocatalytic degradation of a textile dye by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/clinoptilolite nanocatalyst using Taguchi experimental design

In the current study, a nanophotocatalyst doped with of TiO₂ and Fe₂O₃ nanoparticles supported on Iranian clinoptilolite was synthesized and characterized by XRD, XRF, SEM, and EDX analyses. The results suggested the successful loading of TiO₂ and Fe₂O₃ nanoparticles onto the surface of clinoptilolite. The SEM images confirmed the average size of nanoparticles deposited on zeolite, which was about 20–40 nm. Furthermore, application of the synthesized photocatalyst in photocatalytic degradation of Acid Black 172 dye was studied using the Taguchi method and the chosen parameters were as follows: pH (2–7), dye concentration (50–200 mg/l), irradiation time (30–120 min), and catalyst dosage (0.5–1.5 g/l). The results indicate that dye concentration, pH, and irradiation time are respectively the most effective factors in these experiments while with the minimum dosage of the catalyst (0.5 g/l), up to 90 % removal efficiency could be achieved. The optimum value for each parameter was pH = 2, dye concentration = 50 mg/l, catalyst dosage = 1 g/l and irradiation time = 60 min, and the dye removal efficiency reached up to 100 % at these optimal conditions. Furthermore, after five-times recycling and reusing the catalyst, the efficiency of the photocatalytic degradation was reduced from 91.5 to 65.9 %, which is still an acceptable value.     

Synthesis,characterization and photocatalytic properties of tungsten-doped hydrothermal TiO<Subscript>2</Subscript>

Crystalline anatase phase TiO₂ with photocatalytic properties was obtained through a sol–gel low-temperature hydrothermal process. TiO₂ samples doped with tungsten oxide were also obtained by using this synthetic approach. The photocatalytic oxidation of methylene blue in water was monitored to study the influence of the tungsten doping degree on the photocatalytic degradation performance of TiO₂. The degradation rate constant was further increased by adjusting the tungsten doping degree of hydrothermal TiO₂. Also, a much faster photodegradation of methylene blue was achieved using tungsten doped samples baked at 450°C. The results were compared with those obtained with Degussa P25 used as photocatalyst. The structure and optical properties of tungsten-doped TiO₂ were studied by SEM, X-ray diffraction, UV–vis and DRIFT spectroscopy techniques.     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

A study on the degradation of methamidophos in the presence of nano-TiO<Subscript>2</Subscript> catalyst doped with Re

A new Re-doped nano-TiO₂ photocatalyst was synthesized by immersion method. The novel doped nano-TiO₂ photocatalyst utilizing visible light was firstly prepared. The doped nano-TiO₂ powder was charactered by XRD, FTIR, UV-Vis, and its photocatalytic activity was tested through the photocatalytic degradation of methamidophos as a model compound under ultraviolet irradiating and in sunlight, respectively. In order to compare the photocatalytic activities, the same experiment was carried out for undoped nano-TiO₂. The degradation ratio of methamidophos in the presence of doped nano-TiO₂ reached 64.40% under sunlight for 12 h, which was 2.64% in the presence of undoped nano-TiO₂. The degradation ratio of methamidophos in the presence of doped nanoTiO₂ reached 90.39% under UV irradiationat 2.5 h, which was 51.29% in the presence of undoped nano-TiO₂. All the results show that the doped TiO₂ is a promising photocatalyst using sunlight for treating the organophosphorous pesticide wastewater. The article is published in the original.     

Preparation of TiO<Subscript>2</Subscript> nanofibers immobilized on quartz substrate by electrospinning for photocatalytic degradation of ranitidine

The photocatalytic activity of TiO₂ nanofibers immobilized on quartz substrates was investigated by evaluating the decomposition of organic pollutants. TiO₂ nanofibers were synthesized by electrospinning the Ti-precursor/polymer mixture solution, followed by hot-pressing for enhancing the adhesion of TiO₂-nanofiber films to the substrates. TiO₂ started to crystalize in the anatase form at 500 °C and reached the optimal photocatalytic anatase/rutile phase ratio of 70:30 at a calcination temperature of 600 °C. The TiO₂-nanofiber film was demonstrated to be an efficient photocatalyst by ranitidine decomposition under UV illumination and was proven to have a comparable photocatalytic activity with the well-known Degussa P25 nanoparticulate photocatalyst and excellent recyclability during 10 cycles of photocatalytic operation, indicating no loss of TiO₂ nanofibers during photocatalytic operations.     

Structural characterization and photocatalytic properties of novel Bi<Subscript>2</Subscript>FeVO<Subscript>7</Subscript>

Bi₂FeVO₇ was prepared by a solid-state reaction technique for the first time and the structural and photocatalytic properties of Bi₂FeVO₇ were studied. The results shows that this compound crystallized in the tetragonal crystal system with space group I4/mmm. Moreover, the band gap of Bi₂FeVO₇ was estimated to be about 2.22(6) eV. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂FeVO₇ as the photocatalyst by ultraviolet light irradiation. Degradation of aqueous methylene blue (MB) dye by photocatalytic way over this compound was further studied under visible light irradiation. Bi₂FeVO₇ shows higher catalytic activity compared to TiO₂ (P-25) for MB photocatalytic degradation under visible light irradiation. Complete removal of aqueous MB was realized after visible light irradiation for 170 min with Bi₂FeVO₇ as the photocatalyst. The reduction of the total organic carbon (TOC) and the formation of inorganic products, SO ₄ ²⁻ and NO ₃ ⁻ revealed the continuous mineralization of aqueous MB during the photocatalytic course.     

Sol-gel preparation of Fe-doped mixed crystal TiO<Subscript>2</Subscript> powder and its photocatalytic activity for degradation of azo fuchsine under visible light irradiation

In this work, the Fe-doped mixed crystal TiO₂ photocatalyst which can utilize visible light was prepared by sol-gel and heat-treated methods. During heat-treatment, the phase transformation of Fe-doped TiO₂ powder occurs and the process is characterized by XRD and TG-DTA technologies. Otherwise, the sizes and shapes of Fe-doped and undoped TiO₂ powders were also compared using TEM images. The azo fuchsine in aqueous solutions, as a model compound, was treated under visible light irradiation using Fe-doped mixed crystal TiO₂ powders as photocatalyst. The results showed that, under visible light irradiation, the (0.25%) Fe-doped mixed crystal TiO₂ powder heat-treated at 600°C for 3.0 h behaved very high photocatalytic activities for degradation of azo fuchsine. The remarkable improvement of the photocatalytic activity of TiO₂ powder was elucidated through the cooperative effects of iron doping and phase transformation. The iron doping can restrain the recombination of photogenerated electron-hole pairs and the phase transformation can enhance the absorption of visible light. Furthermore, other influence factors such as azo fuchsine concentration, solution acidity, Fe3+ ion content and irradiation time were also studied. Thus, this method is applicable for the treatment of wastewater.     

TiO<Subscript>2</Subscript> Photocatalytic Oxidation: II. Gas-Phase Processes

The results of studies on the TiO₂ photocatalytic oxidation of model air pollutants are summarized. The kinetics of photocatalytic oxidation of CO and the vapors of a number of simple organic substances was studied in detail. It was found that, in the course of reaction, all of the test substances underwent complete mineralization. Gaseous substrates were converted with the participation of several types of reaction centers. The photocatalytic oxidation of sulfur- and phosphorus-containing substances resulted in gradual deactivation of the photocatalyst; however, its activity can be restored by washing the photocatalyst with water. It was found that, along with oxidation, the steps of hydrolysis play an important role in the photocatalytic degradation of air pollutants, such as dimethyl methylphosphonate and 2-chloroethyl sulfide.__________Translated from Kinetika i Kataliz, Vol. 46, No. 3, 2005, pp. 450–465.Original Russian Text Copyright © 2005 by Vorontsov, Kozlov, Smirniotis, Parmon.     

Effective photocatalytic degradation of an azo dye over nanosized Ag/AgBr-modified TiO<Subscript>2</Subscript> loaded on zeolite

Zeolite-based photocatalysts were prepared by the sol-gel and deposition methods. The photocatalysts were characterised by X-ray diffraction, nitrogen adsorption-desorption isotherms, FTIR spectroscopy, scanning electron microscopy and energy-dispersive X-ray spectrometry. The activity of the prepared photocatalysts was evaluated by the UV-induced degradation of acid blue 92, a textile dye in common use. The effect of various parameters, such as catalyst concentration, initial dye concentration, thiosulphate concentration and pH, on the rate and efficiency of the photocatalytic degradation of acid blue 92 was investigated. The results showed that each parameter influenced the degradation rate and efficiency in a particular way. It was also found that, under optimised conditions, Ag/AgBr/TiO₂/zeolite exhibited the highest photocatalytic performance. A comparison of catalytic activity when exposed to visible light under the same conditions showed that the photocatalysts containing AgBr had the highest activity.     

Enhancement of SrTiO<Subscript>3</Subscript>/BiPO<Subscript>4</Subscript> heterostructure for simulated organic wastewater degradation under UV light irradiation

A novel SrTiO₃/BiPO₄ heterostructure with different amounts of SrTiO₃ have been successfully prepared through the hydrothermal process. The photocatalysts were characterized by X-ray powder diffraction, UV–Vis diffuse reflectance spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, high-resolution transmission electron microscopy, and X-ray photoelectron spectroscopy. The photocatalytic performance was evaluated by degrading the methylene blue dye solution under UV light. Results showed that the samples displayed excellent photocatalytic degradation efficiency due to the highly efficient suppression of the recombination of electron–hole pairs. A possible mechanism of SrTiO₃/BiPO₄ heterojunctions was discussed. The research indicated that the as-prepared SrTiO₃/BiPO₄ heterogeneous photocatalyst can be used as an effective material for degrading industrial organic wastewater.     

Advanced Bi<Subscript>2</Subscript>O<Subscript>2.7</Subscript>/Bi<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript> composite film with enhanced visible-light-driven activity for the degradation of organic dyes

Bi₂O_2.7/Bi₂Ti₂O₇ composite photocatalyst films are synthesized by sol–gel dip-coating. The ratio of adding Bi and Ti precursors can be controlled during the preparation process. The phase structure is confirmed by X-ray diffraction. The UV–visible diffuse reflectance spectrum shows that the composite catalysts present light absorption in the visible region. The obtained Bi₂O_2.7/Bi₂Ti₂O₇ composite films possess superior photocatalytic degradation of rhodamine B, owing to the visible light response of Bi₂O_2.7 and the separation of photogenerated electrons and holes between the two components. As a result, the Bi₂O_2.7/Bi₂Ti₂O₇ (Bi/Ti = 1:1) displays the highest photocatalytic activity under visible light or UV light irradiation for the degradation of different organic dyes, including methyl blue, methyl orange and acid orange 7.     

Enhancement of Photocatalytic Efficiency of TiO2 by Supporting on Clinoptilolite in the Decolorization of Azo Dye Direct Yellow 12 Aqueous Solutions

Structure and physico‐chemical properties of a photocatalyst, especially surface area and absorption ability, were correlated to catalytic activities in photodegradation of dye pollutants in water. In this investigation photocatalytic degradation of azo dye Direct yellow 12 (Chrysophenine G) in water was studied. Titanium(IV) oxide was supported on Clinoptilolite (CP) (Iranian Natural Zeolite) using solid‐state dispersion (SSD) method. The results show that the TiO₂/Clinoptilolite (SSD) is an active photocatalyst. The maximum effect of photo degradation was observed at 10 wt.% TiO₂, 90 wt.% Clinoptilolite. A first order reaction with k = 0.0108 min^?1 was observed. The effects of some parameters such as pH, amount of photocatalyst, initial concentration of dye were examined.     

Novel Visible-Light-Driven Photocatalyst Co<Subscript>3</Subscript>O<Subscript>4</Subscript>/FeWO<Subscript>4</Subscript> for Efficient Decomposition of Organic Pollutants

A highly efficient and visible light (λ ≥ 420 nm) responsive composite photocatalyst, Co₃O₄/FeWO₄ was prepared by simple impregnation method. The heterojunction semiconductors Co₃O₄/FeWO₄ demonstrated notably high photocatalytic activity over a wide range of composition than the individual component Co₃O₄ or FeWO₄ for the complete degradation of 1,4-dichlorobenzene (DCB) in aqueous phase under visible light irradiation. The photocatalytic activity of composite was optimized at 1/99 Co₃O₄/FeWO₄ composition. After 2 h of visible light irradiation 51% decomposition of 1,4-dichlorobenzene (DCB) was observed utilizing 1/99 Co₃O₄/FeWO₄ photocatalyst while the end members demonstrated a negligible degradation under the same experimental condition. The valence band (VB) and conduction band (CB) of Co₃O₄ is located above the VB and CB of FeWO₄, respectively. Both the semiconductors Co₃O₄ and FeWO₄ exhibit strong absorption over the wide range of visible light. The obviously enhanced photocatalytic performance of Co₃O₄/FeWO₄ composite has been discussed on the hole (h⁺) as well as electron (e^?) transfer mechanism between the VB and CB of individual semiconductors.     

Solvothermal Synthesis of Cs0.33WO3/LDHs Composite as a Novel Visible‐Light‐Driven Photocatalyst

A novel Cs_0.33WO₃/LDHs (CWLDH) composite was synthesized by simple two steps solvothermal method and first investigated as the photocatalyst for tetracycline (TC) and Congo red (CR) degradation under visible light irradiation. The CWLDH heterostructures catalysts were characterized by XRD, UV–Vis, SEM, XPS and BET. The composite CWLDH showed enhanced photocatalytic activity compared with pure Cs_0.33WO ₃ and NiAl‐LDH under identical experimental conditions. The enhanced photocatalytic activity was mainly attributed to the higher visible light‐absorbing ability, efficient electron–hole separation and prolonged lifetimes of photogenerated charges. The photocatalyst presented a high photocatalytic activity (92%) at the optimum of CWLDH ‐3 and initial TC concentration of 40 mg L⁻¹. Besides, the degradation efficiency of TC is higher than 75% for reused CWLDH after four cycles, demonstrating that it could be used as a potential catalyst with good photocatalytic activity, stability and reusability. According to the experimental results, a possible photocatalytic mechanism of CWLDH was discussed.