神华煤直接液化残渣超临界溶剂萃取研究

利用甲苯、苯和乙醇三种溶剂在反应釜中对神华煤直接液化残渣进行了超临界溶剂萃取,考察了压力、温度、萃取时间、溶剂/残渣比等对萃取产物收率和重质液体萃取组成的影响。结果表明,以甲苯为溶剂进行萃取时,萃取时间对重质液体产率及HS和A收率的影响不大,而温度、压力以及溶剂/残渣质量比都会影响萃取产物的产率及组成。溶剂超临界萃取过程中,有其他组分向HS组分转化,提高了HS的收率。三种溶剂中,苯显示了和甲苯相似的萃取性能,而乙醇的萃取性能相比苯和甲苯则较差,但乙醇萃取得到的重质液体中轻质组分含量高于苯和甲苯。萃取过程中,残渣中的灰分和硫分主要富集至萃取残渣中。     

以水、甲苯及其混合溶剂超临界萃取煤的研究

在半连续萃取装置上,以水、甲苯及其混合物为溶剂对黄县褐煤进行了非等温超临界萃取,考察了不同溶剂对萃取过程的影响。结果表明,以甲苯为溶剂的萃取率高于以水为溶剂的。以水为溶剂萃取物中的沥青烯和预沥青烯的H/C原子比高于以甲苯为溶剂的,而O/C原子比则低。在水中加入适量甲苯,能够明显改善萃取效果,大幅度提高萃取率。     

褐煤亚临界—超临界水萃取研究

在半连续实验装置上，采用非等温实验技术，以水为溶剂，对大雁、昌宁两种褐煤进行了萃取。结果表明，在适宜条件下可得到高的转化率和较高的萃取物产率；萃取物中 主要馏分为预沥青烯，为原煤中的富氢组分；过程中产生的气体主要分为CO2；萃取物和气体生成速率随温度而变，在400℃左右存在极大值；萃取后褐煤（即残渣）具有比原煤低的水分、低氧含量、高的碳含量及一定的挥发分。本文对对萃取过程进行了宏观动力学处理，结果表明，萃取过程要用一级反应方程式来描述；在萃取的主要温度区间，活化能约为120kJ/mol.     

黄县油页岩超临界萃取研究

在半连续实验装置上,用甲苯作溶剂,用非等温反应进行了黄县两种油页岩超临界萃取研究。考察了温度、压力和供氢溶剂对萃取转化率和产率的影响,提出了适宜的工艺参数。进行了过程动力学处理,求得了表观活化能E_A 和频率因子K_0。     

超临界水中煤基多孔炭孔隙形成过程的研究

在半连续超临界水反应器(SCWR)中考察了不同温度、反应时间下昭通褐煤的转化特性,结合半焦有机官能团及碳微晶结构分析,推测在超临界水中半焦孔隙的形成过程以及煤中矿物质的作用。结果表明,超临界水首先快速萃取出褐煤热解产物,促进了半焦石墨化,形成良好的炭素前驱体,此过程对半焦孔结构基本无作用;当温度高于550 ℃,炭素前驱体发生气化反应,产生了较多的C-O-C交联结构,比表面积明显提高,逐渐形成多孔炭材料;脱灰后的煤在升温过程中具有更高的萃取率,形成有利于微孔产生的炭素前驱体,煤中的矿物质更有利于中孔的形成。     

中国桦甸油页岩超临界萃取研究

对桦甸北台子油页岩样品,用甲苯、甲苯四氢萘混合溶剂进行丁非等温(升温速率为8 K·min~(-1))的超临界萃取实验(萃取压力为10MPa,终温为550℃)。为选择高转化率和油类产物高产率的萃取条件,进行了样品粒度(1.2—2.5mm)、溶剂流率(2dm~3·h~(-1))以及甲苯中供氢组分含量(分别为10%、20%、30%)的系统实验。甲苯溶剂超临界萃取油类产物产率是一般干馏方法的2倍。在溶剂甲苯中加入少量供氢组分后,油母转化完全,油类产物产率高。超临界萃取可用一级反应描述,文中用积分法求解了动力学参数。     

亚临界水脱除煤中硫的实验研究

近年来,超临界流体以其独特的性质作为溶剂或反应介质在众多领域得到应用。对于煤在超临界及亚临界水中的行为研究也越来越受到国内外学者的重视,如Kashimura等、Hu等和Cheng等对褐煤在亚临界及超临界水中的降解行为进行了研究。Timpe等报道了水热处理对年轻煤中有机硫及微量元素的脱除行为。     

褐煤的EDA—DMF萃取和加氢液化性能

考察了三个褐煤样品的乙二胺（EDA）－二甲基甲酰胺（DMF）萃取物的收率及其组成结构与加氢液化性能的关第。结果表明，萃取率、液化转率 及沥青质产率之间有较好的相关性，且三者均随煤化程度的增加而减少。EDA－DMF萃取物中富集了含短 链烷基取代基的芳香族复杂酯（西边）类低分子化合物。推测在液化初期褐煤中－O－和＞C＝O的裂解和加氢可能起着重要的作用。     

超临界苯类溶剂对聚苯乙烯降解的影响

在高压间歇反应器中,温度340~370℃,以苯、甲苯、乙苯和对二甲苯为超临界溶剂研究了聚苯乙烯(PS)的降解特性.苯类物质是聚苯乙烯的优良溶剂,在超临界条件下其优异的传质、传热性能使聚苯乙烯快速降解.聚苯乙烯在不同超临界溶剂中降解转化率相近,而降解产物组成差别很大,分析了不同超临界溶剂对聚苯乙烯降解过程的影响.结果表明超临界甲苯对降解过程影响最小,苯乙烯收率最高.聚苯乙烯降解过程中,高分子链断裂和解聚同时进行,结合连续分布理论建立了聚苯乙烯降解的动力学模型,得到在超临界甲苯中聚苯乙烯链端解聚活化能为138.4 kJ.mol-1.     

连续式超临界水反应器中褐煤制氢过程影响因素的研究

建立了煤处理量为1kg/h的连续式超临界水反应装置并实现稳定运行,考察了反应温度（500℃～650℃）、反应压力(20MPa～30MPa)、水煤浆浓度(20%~50％)以及KOH添加量对小龙潭褐煤在超临界水中连续化制氢的影响。实验结果表明,反应进行20min后连续装置达到稳定运行状态。反应温度和KOH添加量是影响超临界水中褐煤制氢的关键因素。随着反应温度从500℃提高到650℃,氢气的体积分数与产率分别由11%和25mL/g增加到29%和110mL/g。添加0.5%KOH可明显提高碳气化率以及氢气的产率,但随着KOH加入量进一步增加,氢气产率增加的幅度减小。随着压力增加,甲烷产率有升高的趋势,氢气产率变化不大,提高水煤浆的浓度,碳气化率降低。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.