基于壳聚糖膜固定双酶的胆碱传感器的研究

提出了一种基于壳聚糖膜固定辣根过氧化物酶 胆碱氧化酶的胆碱传感器的制备方法。该传感器以电聚合于玻碳电极的硫堇作为电子传递介体,在pH6. 8,外加电压-0. 2V(vs.SCE)条件下,其峰电流与浓度范围 5. 0×10-5 ~3. 0×10-3 mol/L的胆碱呈良好的线性响应;检出限为 1. 0×10-5 mol/L。传感器有良好的选择性和稳定性,使用一月后,仍能保持其初始活性的 80%。     

固定化辣根过氧化物酶和硫堇的过氧化物传感器

利用卡拉胶水凝胶将辣根过氧化物酶和硫堇同时固定在玻碳电极表面,制备以硫堇为媒介体的过氧化物电化学传感器.包埋在卡拉胶水凝胶中的硫堇在pH=7.0的磷酸缓冲溶液中出现了1对氧化还原峰,氧化峰电位和还原峰电位分别在-0.176和-0.264 V,电位差为88 mV,电流比近似为1,说明硫堇在电极表面发生准可逆的电化学反应.硫堇能作为辣根过氧化物酶催化还原过氧化物中的电子媒介体,加速催化还原过程中的电子传递,减少了催化还原过程中的其它氧化物的干扰.传感器检测过氧化物(过氧化氢、异丙苯基过氧化氢、过氧化丁酮、叔丁基过氧化氢)具有较快的响应时间和良好的灵敏度、重现性、稳定性及较长的使用寿命.     

基于固定化纳米金增强化学发光双酶传感器测定葡萄糖

研制了一种新型流动注射化学发光（CL）双酶传感器,用于葡萄糖的检测．该传感器将掺杂金纳米粒子（GNPs）的壳聚糖膜包覆在硅烷化试剂预处理的玻璃微珠上,用于吸附固定葡萄糖氧化酶（GOD）和辣根过氧化物酶（HRP）．葡萄糖在GOD的催化下发生氧化反应生成H2O2,生成的H2O2在HRP的催化作用下与鲁米诺发生反应,并产生化学发光信号．实验表明,壳聚糖中掺杂的GNPs不仅能够有效的吸附酶分子并保持其生物活性,还对Luminol-H2O2-HRP化学发光体系具有增敏作用．通过化学发光光谱和紫外光谱表征,详细研究了固定化GNPs增强Luminol—H2O2-HRP体系的化学发光机理．在优化的实验条件下,该传感器对葡萄糖检测的线性范围为0．01～6．0mmol／L,检测限为5．0μmol／L（3σ）．将所建立的方法用于临床血清样品中葡萄糖含量的测定,获得了满意的结果．     

硫堇-牛血清白蛋白氧化还原复合膜修饰葡萄糖生物传感器的研究

通过交联法和自组装法制备了一种双酶型葡萄糖生物传感器.首先以牛血清白蛋白-戊二醛为交联剂以实现对辣根过氧化物酶(HRP)的固载,再利用凝集素-糖蛋白的识别作用将葡萄糖氧化酶(GOD)分子组装到电极表面,制得双酶型的葡萄糖生物传感器.采用原子力显微镜(AFM)考察了复合膜的性质,同时采用循环伏安法和计时电流法考察了该传感...     

基于Nafion-氧化石墨烯复合物/硫堇/纳米金构建过氧化氢传感器的研究

利用Nafion(全氟聚苯乙烯磺酸溶液)-氧化石墨烯复合物、硫堇和纳米金构建了H2O2酶传感器。首先将氧化石墨烯分散在体积分数0.2%Nafion溶液中制得Nafion-氧化石墨烯的复合物,并将其固定在玻碳电极表面,通过静电吸附将带正电荷的硫堇吸附到Nafion-氧化石墨烯复合膜修饰的玻碳电极表面,再利用静电吸附将纳米金修饰于电极上,通过纳米金来固定辣根过氧化物酶从而制得H2O2传感器。用循环伏安法和计时电流法考察该修饰电极的电化学特性。H2O2浓度为5.5×10-6~1.0×10-3mol/L时,酶电极的响应电流值与H2O2的浓度呈良好的线性关系,检出限为1.80×10-6mol/L。     

基于聚硫堇和纳米银固定酶的葡萄糖生物传感器

用循环伏安法将电子媒介体硫堇电聚合在玻碳电极表面上,使其表面形成均匀的带负电的聚硫堇膜,通过静电吸附作用吸附表面带正电荷的纳米银溶胶,接着通过静电吸附带负电的葡萄糖氧化酶,最后用聚硫堇包埋电极,从而制得性能优良的葡萄糖氧化酶(GOD)生物传感器。实验发现传感器氧化峰电流与葡萄糖的浓度在1.0×10-8~5.0×10-6mol/L(r=0.9963)范围内呈良好线性关系,检出限为5.0×10-9mol/L(S/N=3)。     

基于聚硫堇和纳米金共修饰的过氧化氢生物传感器的研究

用循环伏安法将电子媒介体硫堇电聚合在铂电极上,使其表面形成均匀的带负电的聚合膜层,通过静电吸附作用固定表面带正电荷的辣根过氧化物酶,接着吸附纳米金,然后再利用纳米金吸附固定一层辣根过氧化物酶,制成了新型过氧化氢生物传感器。实验发现,该传感器增加了酶的吸附量,响应快、灵敏度高、稳定性好,对H2O2表现出良好的响应特性。检测范围为5.2×10-7~2.0×10-3mol/L,检出限为1.7×10-7mol/L,并具有抗尿酸、抗坏血酸等干扰的特点。     

基于硫堇/碳纳米管修饰电极的新型过氧化氢电化学传感器

基于碳纳米管(CNTs)和硫堇(Th)的协同效应,将辣根过氧化物酶(HRP)通过戊二醛(GA)交联作用固定在硫堇(Th)/CNTs修饰电极上,构造了一种新型酶电极(HRP/GA-Th/CNTs/GC)。CNTs静电吸附正电荷的Th,而Th不仅可以促进电极和酶的氧化还原活性中心之间的电子传递,而且能使CNTs氨基(—NH2)功能化,从而利于HRP的固定。基于HRP/GA-Th/CNTs/GC电极的过氧化氢传感器具有较好的传感性能,且检出限低(0.3μmol.L-1)、响应时间短(5 s内)、抗干扰能力强。     

基于硫堇/碳纳米管修饰金电极的过氧化氢生物传感器

制备了以硫堇(TH)、纳米金(Nano-Au)及多壁碳纳米管(MWNT)修饰的H2O2生物传感器.探讨了工作电位、温度、pH对电极响应的影响,考察了电极的重现性、抗干扰能力及使用寿命.该传感器具有线性范围宽、检出限低、灵敏度高、稳定性好和抗干扰能力强等特点.其线性范围为7.0×10-7～4.0×10-3 mol/L;检出限为2.3×10-7 mol/L;灵敏度为0.13 A/(mol L-1 cm2);达到稳定电流所用时间《9 s.米氏常数为0.62 mmol/L,表明所固定的酶具有较高的生物活性.     

基于铁氰酸镍修饰的双酶电流型胆碱传感器的研究

提出了一种以电沉积铁氰酸镍(NiHCF)无机膜为介体的胆碱传感器的制备方法。该传感器以壳聚糖为酶固定基质,用戊二醛作交联剂分别固定辣根过氧化物酶和胆碱氧化酶。该传感器在pH6.8,外加电压-0.1V条件下,对2.0×10-5～1.0×10-3mol/L的胆碱呈良好的线性响应,检出限为5.0×10-6mol/L。传感器有良好的选择性和稳定性,使用1个月后,仍能保持其初始活性的75%。     

Fabrication of Bienzymatic Glucose Biosensor Based on Novel Gold Nanoparticles‐Bacteria Cellulose Nanofibers Nanocomposite

An exploration of gold nanoparticles–bacterial cellulose nanofibers (Au‐BC) nanocomposite as a platform for amperometric determination of glucose is presented. Two enzymes, glucose oxidase (GOx) and horseradish peroxidase (HRP) were immobilized in Au‐BC nanocomposite modified glassy carbon electrode at the same time. A sensitive and fast amperometric response to glucose was observed in the presence of electron mediator (HQ). Both of GOx and HRP kept their biocatalytic activities very well in Au‐BC nanocomposite. The detection limit for glucose in optimized conditions was as low as 2.3 µM with a linear range from 10 µM to 400 µM. The biosensor was successfully applied to the determination of glucose in human blood samples.     

纳米聚苯胺修饰石墨电极的葡萄糖双酶传感器

用循环伏安法在石墨电极上制得纳米纤维聚苯胺, 并在其上固定葡萄糖氧化酶(GOD)和辣根过氧化物酶(HRP)制备葡萄糖双酶传感器. 用交流阻抗、SEM等技术对其进行表征; 考察了各种因素对双酶电极响应电流的影响以及双酶电极的稳定性. 该传感器对葡萄糖响应电流的测定在0.05 V(vs SCE)下进行, 有效避免了电活性物质的影响, 线性响应范围为0.05-2.0 mmol·L-1.     

A Glucose Biosensor Based on Immobilization of Glucose Oxidase on Platinum Nanoparticle Doped Santa Barbara Amorphous Material-15

A novel electrochemical glucose biosensor was prepared by combining platinum nanoparticle doped Santa Barbara Amorphous Material 15 with glucose oxidase. The resulting material demonstrated high stability and reactivity for catalyzing glucose electrolytic oxidation, primarily due to the high surface area of these catalysts. This glucose biosensor was capable of interference-free determination of glucose with a linear dynamic range from 0.03 to 12.0 mmol L^?1. In addition, it has the advantages of simple preparation and good stability. The reported method is promising for the determination of glucose in human serum.     

A Chemiluminescence Optical Fiber Glucose Biosensor Based on Co-immobilizing Glucose Oxidase and Horseradish Peroxidase in a Sol-gel Film

IntroductionIn recent years chemiluminescence (CL)biosensor prepared by immobilization of a sensitivereagent such as peroxidase or oxidase onto a solidmatrix has attracted much attention due to the highsensitivity of the chemiluminescent reaction of thesensitive reagent even with a simple instrument.Generally,CL biosensors can be divided into twocategories.One consists of hydrogen peroxide sen-sors prepared by immobilizing a kind of peroxidaseonto a suitable solid support[1,2 ] ,and the immo…     

Unadulterated Glucose Biosensor Based on Direct Electron Transfer of Glucose Oxidase Encapsulated Chitosan Modified Glassy Carbon Electrode

Glucose oxidase (GOD) was encapsulated in chitosan matrix and immobilized on a glassy carbon electrode, achieving direct electron transfer (DET) reaction between GOD and electrode without any nano‐material. On basis of such DET, a novel glucose biosensor was fabricated for direct bioelectrochemical sensing without any electron‐mediator. GOD incorporated in chitosan films gave a pair of stable, well‐defined, and quasireversible cyclic voltammetric peaks at about ?0.284 (E_pa) and ?0.338 V (E_pc) vs. Ag/AgCl electrode in phosphate buffers. And the peak is located at the potentials characteristic of FAD redox couples of the proteins. The electrochemical parameters, such as midpoint potential (E_1/2) and apparent heterogeneous electron‐transfer rate constants (k_s) were estimated to ?0.311 V and 1.79 s^?1 by voltammetry, respectively. Experimental results indicate that the encapsulated GOD retains its catalytic activity for the oxidation of glucose. Such a GOD encapsulated chitosan based biosensor revealed a relatively rapid response time of less than 2 min, and a sufficient linear detection range for glucose concentration, from 0.60 to 2.80 mmol L^?1 with a detection limit of 0.10 mmol L^?1 and electrode sensitivity of 0.233 μA mmol^?1. The relative standard deviation (RSD) is under 3.2% (n=7) for the determination of practical serum samples. The biologic compounds probably existed in the sample, such as ascorbic acid, uric acid, dopamine, and epinephrine, do not affect the determination of glucose. The proposed method is satisfactory to the determination of human serum samples compared with the routine hexokinase method. Both the unique electrical property and biocompatibility of chitosan enable the construction of a good bio‐sensing platform for achieved DET of GOD and developed the third‐generation glucose biosensors.     

Amperometric Glucose Biosensor Based on the Deposition of Copper and Glucose Oxidase onto Glassy Carbon Transducer

ABSTRACT

The performance of a first generation glucose amperometric biosensor based on the entrapment of glucose oxidase (GOx) within a net of copper electrodeposited onto activated glassy carbon electrode, is described. The copper electrodeposited offers an efficient electrocatalytic activity towards the reduction of enzymatically-liberated hydrogen peroxide, allowing for a fast and sensitive glucose quantification. The influence of the electrodeposition conditions (pH, potential, time, copper salt and enzyme concentrations) on the response of the bioelectrode was evaluated from the amperometric signals of hydrogen peroxide and glucose. The combination of copper electrodeposition with a nation membrane allows an excellent selectivity towards easily oxidizable compounds such as uric and ascorbic acids at an operating potential of -0.050 V. The response is linear up to 2.0 × 10^?2 M glucose, the detection limit being 1.2 × 10^?3 M.     

Development of Amperometric Glucose Biosensor Based on Reconstitution of Glucose Oxidase on Polymeric 3‐Aminophenyl Boronic Acid Monolayer

An amperometric biosensor for determining glucose based on deflavination of the enzyme glucose oxidase and subsequent reconstitution of the apo‐protein with a complexed flavin adenine dinucleotide (FAD) monolayer is described. The GOx‐reconstituted electrode exhibited excellent electrocatalytic activities towards the reduction and oxidation of hydrogen peroxide as well. The prepared biosensor showed an excellent performance for glucose at +0.5 V with a high sensitivity (5.94 μA/mM) and relatively good response time (～12 s) in a wide concentration range of 1–17 mM (correlation coefficient of 0.9998). The applicability to blood analysis was also evaluated.     

镀铂金电极上电沉积碳纳米管-葡萄糖氧化酶-壳聚糖的新型生物传感器

通过电化学沉积将壳聚糖、葡萄糖氧化酶和碳纳米管固定到镀铂金电极上,制备了一种新型葡萄糖生物传感器.探讨了铂的电沉积时间、壳聚糖化学沉积时间、缓冲溶液pH和工作电位等对该牛物传感器的影响.实验结果表明,该生物传感器线性范围为1×10~(-6)1.2×10~(-2)mol/L,相关系数为0.9974,检测限为5.0×10~(-7)mol/L,响应时间≤8 s;血清中的尿酸、抗坏血酸等对葡萄糖的测定无干扰.利用该生物传感器测定了人血清中的葡萄糖,回收率在97%～105%之间.该生物传感器线性范围较宽,灵敏度高,响应迅速,抗干扰能力强,有望成为一种可推广的新型葡萄糖检测器.     

Enzyme-Based Fiber Optic Sensor for Glucose Determination

Abstract

A new fiber-optic probe for the determination of glucose is developed. Glucose oxidase is immobilized on a preactivated Immunodyne membrane by direct application of the enzymatic solution to one side of the membrane. The membrane is then placed around the common end of a bifurcated glass fiber optic bundle, and immersed in the sample cell which contains the glucose sample, peroxidase and a colorless dye. Glucose is quantified by the color change when the reaction takes place.     

基于溶胶-凝壳聚糖/SiO2杂化材料的安培型葡萄糖生物传感器

近年来 ,基于溶胶 -凝胶技术的有机 /无机杂化复合材料由于具有有机物的柔性和易修饰性 ,以及无机物的刚性和稳定性等 ,因此有利于保持生物分子的活性和生物传感器的研制 [1] .壳聚糖 ( CS)具有易成膜性和生物相容性 ,其在生物传感器中的研究已受到重视 [2 ] .本文通过原位溶胶 -凝胶 ( Sol- gel)技术 ,用 CS和甲基三甲氧基硅烷 ( MTOS)制备了 CS/Si O2 有机 /无机杂化材料 ,并将其用于对葡萄糖氧化酶 ( GOD)的固定 ,研制出葡萄糖生物传感器 .采用人工过氧化物酶普鲁士蓝 ( PB) [3]作为电子传递的媒介体 ,并外加一层 Nafion膜以增强…