Ternary blends of poly(ethylene oxide) and acrylate-based copolymers: Crystallinity, miscibility, interactions and proton conductivity

In the present work, blends of poly(ethylene oxide) (PEO), poly(acrylonitrile-co-methyl acrylate) (PANMA) and poly(4-vinylphenol-co-2-hydroxyethyl methacrylate) (PVPh-HEM) were studied by DSC, FTIR and electrochemical impedance spectroscopy (EIS). PEO/PANMA blends were found to be immiscible, while PEO/PVPh-HEM blends are miscible and PVPh-HEM/PANMA exhibits partial miscibility behaviour. The ternary PEO/PANMA/PVPh-HEM blends exhibited miscible compositions for PVPh-HEM and PEO-rich systems. The miscibility observed is a direct consequence of the hydrogen bond interactions among the polymer chains, in which the phenol groups in PVPh-HEM interact with both PEO and PANMA chains. The proton conductivity of a selected membrane based on the ternary blend containing 60% PEO and doped with H₃PO₄ aqueous solution reached 8 × 10⁻³ Ω⁻¹ cm⁻¹ at room temperature and 3 × 10⁻² Ω⁻¹ cm⁻¹ at 80 °C.     

Palladized aluminum electrode covered by Prussian blue film as an effective transducer for electrocatalytic oxidation and hydrodynamic amperometry of N-acetyl-cysteine and glutathione

The mediated oxidation of N-acetyl cysteine (NAC) and glutathione (GL) at the palladized aluminum electrode modified by Prussian blue film (PB/Pd–Al) is described. The catalytic activity of PB/Pd–Al was explored in terms of Fe^III[Fe^III(CN)₆]/Fe^III[Fe^II(CN)₆]¹⁻ system by taking advantage of the metallic palladium layer inserted between PB film and Al, as an electron-transfer bridge. The best mediated oxidation of NAC and GL on the PB/Pd–Al electrode was achieved in 0.5 M KNO₃ + 0.2 M potassium acetate of pH 2. The mechanism and kinetics of the catalytic oxidation reactions of the both compounds were monitored by cyclic voltammetry and chronoamperometry. The charge transfer-rate limiting step as well as overall oxidation reaction of NAC or GL is found to be a one-electron abstraction. The values of transfer coefficients α, catalytic rate constant k and diffusion coefficient D are 0.5, 3.2 × 10² M⁻¹ s⁻¹ and 2.45 × 10⁻⁵ cm² s⁻¹ for NAC and 0.5, 2.1 × 10² M⁻¹ s⁻¹ and 3.7 × 10⁻⁵ cm² s⁻¹ for GL, respectively. The modifying layers on the Pd–Al substrate have reproducible behavior and a high level of stability in the electrolyte solutions. The modified electrode is exploited for hydrodynamic amperometry of NAC and GL. The amperometric calibration graph is linear in concentration ranges 2 × 10⁻⁶–40 × 10⁻⁶ for NAC and 5 × 10⁻⁷–18 × 10⁻⁶ M for GL and the detection limits are 5.4 × 10⁻⁷ and 4.6 × 10⁻⁷ M, respectively.     

Shock membrane electropotential drops and limited diffusive distance of β-amyloids in cerebral neurons are detrimental enhancement to Alzheimer's diseases

Molecular physicobiochemical calculations indicated that the metallic ion binding to beta-amyloids (Aβ) may induce production of hydrogen peroxide, which triggers the Ca ion redistribution from the extracellular to the intracellular compartmentation, resulting in a transient membrane electropotential drop by at least 208.06 mV. Moreover, using the Mark and Houwink empirical equation, we predicted that the diffusible distances of all Aβ identities would be confined in a very tiny region within a radius less than 3.96 × 10⁻⁴ cm in brain at 192 h after produced. Because of the inherent tendency of aggregation behaved by the Aβs, the maximum diffusion coefficient and inherent viscosity were 8.24 × 10⁻¹⁵ cm² s⁻¹ and 72.15 cps for the 12 mers (40.8 kDa), the largest soluble form of ABs.Conclusively, we have quantitatively predicted that the shock membrane potential drop (Δφ > 208.06 mV) and limited diffusible distance (<3.96 × 10⁻⁴ cm) in the brain would contribute the major detrimental effects to the neurons in the Alzheimer's diseases.     

Recombination of KrD and XeD ions with electrons

Recombination rate coefficients of protonated and deuterated ions KrH⁺, KrD⁺, XeH⁺ and XeD⁺ were measured using Flowing Afterglow with Langmuir Probe (FALP). Helium at 1600 Pa and at temperature 250 K was used as a buffer gas in the experiments. Kr, Xe, H₂ and D₂ were introduced to a flow tube to form the desired ions. Because of small differences in proton affinities of Kr, D₂ and H₂ mixtures of ions, KrD⁺/D₃⁺ and KrH⁺/H₃⁺ are formed in the afterglow plasma, influencing the plasma decay. To obtain a recombination rate coefficient for a particular ion, the dependencies on partial pressures of gases used in the ion formation were measured. The obtained rate coefficients, α_KrD+(250 K) = (0.9 ± 0.3) × 10⁻⁸ cm³ s⁻¹ and α_XeD+(250 K) = (8 ± 2) × 10⁻⁸ cm³ s⁻¹ are compared with α_KrH+(250 K) = (2.0 ± 0.6) × 10⁻⁸ cm³ s⁻¹ and α_XeH+(250 K) = (8 ± 2) × 10⁻⁸ cm³ s⁻¹.     

Spectrofluorimetric quantification of bromazepam using a highly selective optical probe based on Eu–bromazepam complex in pharmaceutical and serum samples

A rapid, simple and sensitive spectrofluorimetric method for determination of trace amount of bromazepam is developed. In phosphate buffer of pH 7.4. The bromazepam enhance the luminescence intensity of the Eu³⁺ ion in Eu³⁺–bromazepam complex at λ_ex = 390 nm. The produced luminescence intensity of Eu³⁺–bromazepam complex is in proportion to the concentration of bromazepam. The working range for the determination of bromazepam is 2.3 × 10⁻⁸ to 6.2 × 10⁻⁷ M with detection limit (LoD) and quantitative detection limit (LoQ) of 3 × 10⁻⁹ and 1.2 × 10⁻⁸ M, respectively. While, the working range, detection limit (LoD) and quantitative detection limit (LoQ) in case of the quantum yield calculations are 3.7 × 10⁻⁸ to 3.4 × 10⁻⁷ M with of 3.4 × 10⁻⁹ and 9.2 × 10⁻⁸ M, respectively. The enhancement mechanism of the luminescence intensity in the Eu³⁺–bromazepam system has been also explained.     

Hollow fiber membrane of yttrium-stabilized zirconia and strontium-doped lanthanum manganite dual-phase composite for oxygen separation

The hollow fiber composite membrane involving Zr_0.84Y_0.16O_1.92 (YSZ) as an oxygen ionic conductor and La_0.8Sr_0.2MnO_3−δ (LSM) as an electronic conductor was explored for oxygen separation application. The hollow fiber precursor was prepared by the phase-inversion process, and transformed to a gas-tight ceramic by sintering at 1350 °C. The as-prepared fiber exhibited a thermal expansion coefficient of 11.1 × 10⁻⁶ K⁻¹ and a three-point bending strength of 152 ± 12 MPa. An oxygen permeation flux of 2.1 × 10⁻⁷ mol cm⁻² s⁻¹ was obtained under air/He gradient at 950 °C for a hollow fiber of length 57.00 mm and wall thickness 0.16 mm. The oxygen permeation flux remained unchanged when the sweeping gas was changed from helium to high concentration of CO₂. Considering the satisfactory trade-off between the permeability and stability, the YSZ–LSM hollow fiber is promising for oxygen production applications.     

Reactions of CO2 with H, H2 and deuterated analogues

Combining a temperature variable 22-pole ion trap with a cold effusive beam of neutrals, rate coefficients k(T) have been measured for reactions of CO₂⁺ ions with H, H₂ and deuterated analogues. The neutral beam which is cooled in an accommodator to T_ACC, penetrates the trapped ion cloud with a well-characterized velocity distribution. The temperature of the ions, T_22PT, has been set to values between 15 and 300 K. Thermalization is accelerated by using helium buffer gas. For reference, some experiments have been performed with thermal target gas. For this purpose hydrogen is leaked directly into the box surrounding the trap. While collisions of CO₂⁺ with H₂ lead exclusively to the protonated product HCO₂⁺, collisions with H atoms form mainly HCO⁺. The electron transfer channel H⁺ + CO₂ could not be detected (<20%). Equivalent studies have been performed for deuterium. The rate coefficients for reactions with atoms are rather small. Within our relative errors of less than 15%, they do not depend on the temperature of the CO₂⁺ ions nor on the velocity of the atoms (k(T) lays between 4.5 and 4.7 × 10⁻¹⁰ cm³ s⁻¹ with H as target, and 2.2 × 10⁻¹⁰ cm³ s⁻¹ with D). For collisions with molecules, the reactivity increases significantly with falling temperature, reaching the Langevin values at 15 K. These results are reported as k = α (T/300 K)^β with α = 9.5 × 10⁻¹⁰ cm³ s⁻¹ and β = −0.15 for H₂ and α = 4.9 × 10⁻¹⁰ cm³ s⁻¹ and β = −0.30 for D₂.     

Etude des propriétés de conduction électrique des polyphosphates: Li3Ba2(PO3)7, LiPb2(PO3)5, LiCs(PO3)2, et αLiK(PO3)2

The electrical conductivity of the crystallized polyphosphates Li₃Ba₂(PO₃)₇, LiPb₂(PO₃)₅, LiCs(PO₃)₂, and αLiK(PO₃)₂ has been determined at different temperatures by impedance spectroscopy. The conductivity, σ, spreads within a range of 1.59 × 10⁻⁸ to 1.79 × 10⁻⁷ S cm⁻¹ at 573 K, and from 1.71 × 10⁻⁵ to 9.86 × 10⁻⁴ S cm⁻¹ at 773 K. The transport should be assumed in the majority by the lithium ions with regard to the structural characteristics of these polyphosphates. The results are discussed and compared to the conductivity properties of other lithium ion conductors.     

High performance protonic ceramic membrane fuel cells (PCMFCs) with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

Protonic ceramic membrane fuel cells (PCMFCs) based on proton-conducting electrolytes have attracted much attention because of many advantages, such as low activation energy and high energy efficiency. BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) electrolyte based PCMFCs with stable Ba_0.5Sr_0.5Zn_0.2Fe_0.8O_3−δ (BSZF) perovskite cathode were investigated. Using thin membrane BZCY7 electrolyte (about 15 μm in thickness) synthesized by a modified Pechini method on NiO-BZCY7 anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.015 V, a maximum power density of 486 mW cm⁻², and a low polarization resistance of the electrodes of 0.08 Ω cm² was achieved at 700 °C. The results have indicated that BZCY7 proton-conducting electrolyte with BSZF cathode is a promising material system for the next generation solid oxide fuel cells.     

Characterization of a 10.3-μm pulsed DFB quantum cascade laser

We have measured the output parameters of a 10.3-μm pulsed distributed-feedback (DFB) quantum cascade (QC) laser manufactured by Alpes Lasers and intended for high-sensitivity detection of ammonia and ethylene. The laser beam was collimated with an AR-coated aspheric ZnSe lens with focal length of 11.6 mm and clear aperture of 16.5 mm. Near- and far-field distributions of the laser emission were recorded with an infrared imaging camera. The fast-and slow-axis laser beam divergences were measured to be 1.2 and 1.4 mrad (FWHM), respectively. The divergence was found to be increasing with injection current. An air-spaced Fabry–Perot interferometer with free spectral range of 0.05 cm⁻¹ was used to measure the frequency tuning rates of the laser. The laser was tuned by either heat sink temperature, injection current or pulse repetition rate with rates of −8 × 10⁻² cm⁻¹ K⁻¹, −7 × 10⁻² cm⁻¹ A⁻¹ and −9 × 10⁻⁴ cm⁻¹ kHz⁻¹, respectively. The laser frequency decreased linearly with a rate of 10⁻² cm⁻¹ ns⁻¹ (300 MHz ns⁻¹) for laser pulses varied from 10 to 50 ns, and the frequency chirp rate was found to decrease for longer laser pulses.     

Study on dynamic interfacial tension of 3-dodecyloxy-2-hydroxypropyl trimethyl ammonium bromide at liquid/liquid interface

Dynamic interfacial tension between aqueous solutions of 3-dodecyloxy-2-hydroxypropyl trimethyl ammonium bromide (R₁₂HTAB) and n-hexane were measured using the spinning drop method. The effects of the R₁₂HTAB concentration (the concentration below the CMC) and temperature on the dynamic interfacial tension have been investigated; the reason of the change of dynamic interfacial tension with time has been discussed. The effective diffusion coefficient, D_a, and the adsorption barrier, _a, have been obtained from the experimental data using the extended Word–Tordai equation. The results show that the dynamic interfacial tension becomes smaller while _a becomes higher with increasing R₁₂HTAB concentration in the bulk aqueous phase. D_a decreases from 5.56 × 10⁻¹² m⁻² s⁻¹ to 0.87 × 10⁻¹² m⁻² s⁻¹ while _a increases from 5.41 kJ mol⁻¹ to 7.74 kJ mol⁻¹ with the increase of concentration in the bulk solution of R₁₂HTAB from 0.5 × 10⁻³ mol dm⁻³ to 4 × 10⁻³ mol dm⁻³. Change of temperature affects the adsorption rate through altering D_a and _a. The value of D_a increases from 5.56 × 10⁻¹² m⁻² s⁻¹ to 13.98 × 10⁻¹² m⁻² s⁻¹ while that of _a decreases from 5.41 kJ mol⁻¹ to 5.07 kJ mol⁻¹ with temperature ascending from 303 K to 323 K. The adsorption of surfactant from the bulk phase into the interface follows a mixed diffusion–activation mechanism, which has been discussed in the light of interaction between surfactant molecules, diffusion and thermo-motion of molecules.     

Recombination of HCO and DCO ions with electrons

Recombination of HCO⁺ and DCO⁺ ions with electrons was studied in afterglow plasma. The flowing afterglow with Langmuir probe (FALP) apparatus was used to measure the recombination rate coefficients and their temperature dependencies in the range 150–270 K. To obtain a recombination rate coefficient for a particular ion, the dependencies on partial pressures of gases used in the ion formation were measured. The variations of α_HCO⁺(T) and α_DCO⁺(T) seem to obey the power law: α_HCO⁺(T) = (2.0 ± 0.6) × 10⁻⁷ (T/300)^−1.3 cm³ s⁻¹ and α_DCO⁺(T) = (1.7 ± 0.5) × 10⁻⁷ (T/300)^−1.1 cm³ s⁻¹ over the studied temperature range.     

Comparison of the effects of visible femtosecond laser pulses and continuous wave laser radiation of low average intensity on the clonogenicity of Escherichia coli

To evaluate the contribution of local pulsed heating of light-absorbing microregions to biochemical activity, irradiation of Escherichia coli was carried out using femtosecond laser pulses (λ = 620 nm, τ_p=3 × 10⁻¹³ s, f_p = 0.5 Hz, E_p = 1.1 × 10⁻³J cm⁻², I_av = 5.5 × 10⁻⁴ W cm⁻², I_p = 10⁹ W cm⁻²) and continuous wave (CW) laser radiation (λ = 632.8 nm, I = 1.3 W cm⁻²). The irradiation dose required to produce a similar biological effect (a 160%–190% increase in the clonogenic activity of the irradiated cells compared with the non-irradiated controls) is a factor of about 10³ lower for pulsed radiation than for CW radiation (3.3 × 10⁻¹ and 7.8 × 10² J cm⁻² respectively). The minimum size of the microregions transiently heated on irradiation with femtosecond laser pulses is estimated to be about 10 Å, which corresponds to the size of the chromophores of hypothetical primary photoacceptors—respiratory chain components.     

Voltammetric studies on the α-tocopherol anion and α-tocopheroxyl (Vitamin E) radical in acetonitrile

The α-tocopheroxyl radical was generated voltammetrically by one-electron oxidation of the α-tocopherol anion (E ^r_1/2=−0.73 V versus Ag|Ag⁺) that was prepared by reacting α-tocopherol with Et₄NOH in acetonitrile (with Bu₄NPF₆ as the supporting electrolyte). Cyclic voltammograms recorded at variable scan rates (0.05–10 V s⁻¹), temperatures (−20 to 20°C) and concentrations (0.5–10 mM) were modelled using digital simulation techniques to determine the rate of bimolecular self-reaction of α-tocopheroxyl radicals. The k values were calculated to be 3×10³ l mol⁻¹ s⁻¹ at 20°C, 2×10³ l mol⁻¹ s⁻¹ at 0°C and 1.2×10³ l mol⁻¹ s⁻¹ at −20°C. In situ electrochemical-EPR experiments performed at a channel electrode confirmed the existence of the α-tocopheroxyl radical.     

Copper(II)-cetyltrimethylammonium chloride-chromal blue G ternary complex and its application to the spectrophotometric determination of copper(II)

A sensitive spectrophotometric method for the determination of copper(II) based on a ternary complex with chromal blue G, a triphenylmethane reagent in the presence of cetyltrimethylammonium chloride, is described. The sensitivity of color reaction between copper and chromal blue G has been greatly increased by the sensitizing action of cetyltrimethylammonium chloride, a cationic surfactant. The color development of the ternary complex can be utilized in the highly sensitive spectrophotometric determination of copper. The molar absorptivity of the binary complex between copper and chromal blue G ε_630nm = 9.56 × 10³liters · mol⁻¹ · cm⁻¹ is enchanced on ternary complex formation to ε_{542 nm} = 4.78 × 10⁴liters · mol⁻¹ · cm⁻¹. The ternary complex gave a maximal absorbance at 542 nm in the pH range 9.8–11. Beer's law is obeyed up to at least 1.2 ppm of copper. The maximal absorbance of the ternary complex was found to develop within 5 min and then it remains constant for several hours. The formation constant of the ternary complex is calculated to be 8.6 × 10¹⁰ under these conditions.     

Fluorescence enhancement effect for the determination of DNA with calcein-cetyl trimethyl ammonium bromide system

A new spectrofluorimetric method was developed for the determination of trace amounts of DNA using the calcein as a fluorescent probe. In the presence of appropriate amounts of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB), the anionic dye calcein dimerizes. The weak fluorescence intensity of the dimer was enhanced by adding DNA at pH 6–7. The interaction between calcein–CTAB and DNA was studied on the basis of this behavior and a new method was developed for determining DNA. Under the optimal conditions, the enhanced fluorescence intensity was in proportion to the concentration of DNA in the range of 4.0 × 10⁻⁶ to 8.0 × 10⁻⁵ g L⁻¹ for fsDNA and thermally denatured ctDNA (4.5 × 10⁻⁶ to 9.0 × 10⁻⁵ g L⁻¹). The detection limits (S/N = 3) were 2.0 × 10⁻⁶ and 2.2 × 10⁻⁶ g L⁻¹, respectively. This method was used for determining the concentration of DNA in synthetic samples with satisfactory results.     

Novel method for the preparation of ionically crosslinked sulfonated poly(arylene ether sulfone)/polybenzimidazole composite membranes via in situ polymerization

A series of ionically crosslinked composite membranes were prepared from sulfonated poly(arylene ether sulfone) (SPAES) and polybenzimidazole (PBI) via in situ polymerization method. The structure of the pristine polymer and the composite membranes were characterized by FT-IR. The performance of the composite membranes was characterized. The study showed that the introduction of PBI led to the reduction of methanol swelling ratio and the increase of mechanical properties due to the acid–base interaction between the sulfonic acid groups and benzimidazole groups. Moreover, the oxidative stability and thermal stability of the composite membranes were improved greatly. With the increase of PBI content, the methanol permeability coefficient of the composite membranes gradually decreased from 1.59 × 10⁻⁶ cm²/s to 1.28 × 10⁻⁸ cm²/s at 30 °C. Despite the fact that the proton conductivity decreased to some extent as a result of the addition of PBI, the composite membrane with PBI content of 5 wt.% still showed a proton conductivity of 0.201 S/cm at 80 °C which could actually meet the requirement of proton exchange fuel cell application. Furthermore, the composite membranes with PBI content of 2.5–7.5 wt.% showed better selectivity than Nafion117 taking into consideration the methanol swelling ratio and proton conductivity comprehensively.     

EPR and optical absorption studies of Cr ions in d-gluconic acid monohydrate

EPR studies are carried out on Cr³⁺ ions doped in d-gluconic acid monohydrate (C₆H₁₂O₇·H₂O) single crystals at 77 K. From the observed EPR spectra, the spin Hamiltonian parameters g, |D| and |E| are measured to be 1.9919, 349 (×10⁻⁴) cm⁻¹ and 113 (×10⁻⁴) cm⁻¹, respectively. The optical absorption of the crystal is also studied at room temperature. From the observed band positions, the cubic crystal field splitting parameter Dq (2052 cm⁻¹) and the Racah interelectronic repulsion parameter B (653 cm⁻¹) are evaluated. From the correlation of EPR and optical data the nature of bonding of Cr³⁺ ion with its ligands is discussed.     

Simultaneous determination of hydroquinone and catechol at PASA/MWNTs composite film modified glassy carbon electrode

A poly-amidosulfonic acid and multi-wall carbon nanotubes composite (PASA/MWNTs) modified electrode has been constructed by electropolymerization on glassy carbon electrode (GCE). The electrochemical behaviors of hydroquinone (HQ) and catechol (CC) were investigated using cyclic and differential pulse voltammetries (DPVs) at the prepared electrode. Separation of the reductive peak potentials for HQ and CC was about 120 mV in pH 6.0 phosphate buffer solution (PBS), which makes it suitable for simultaneous determination of these compounds. In the presence of 1.0 × 10⁻⁴ mol L⁻¹ isomer, the reductive peak currents of DPV are proportional to the concentration of HQ in the range of 6.0 × 10⁻⁶ to 4.0 × 10⁻⁴ mol L⁻¹, and to that of CC in the range of 6.0 × 10⁻⁶ to 7.0 × 10⁻⁴ mol L⁻¹. When simultaneously changing the concentration of both HQ and CC, the linear concentration range of HQ (or CC) is 6.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ (or 6.0 × 10⁻⁶ to 1.8 × 10⁻⁴ mol L⁻¹), and the corresponding detection limits are 1.0 × 10⁻⁶ mol L⁻¹. The proposed method has been applied to simultaneous determination of HQ and catechol in water sample, and the results are satisfactory.     

Oxidative degradation of non-ionic surfactant (TritonX-100) by chromium(VI)

Degradation of polyoxyethylene chain of non-ionic surfactant (TritonX-100) by chromium(VI) has been studied spectrophotometrically under different experimental conditions. The reaction rate bears a first-order dependence on the [Cr(VI)] under pseudo-first-order conditions, [TritonX-100]  [Cr(VI)] in presence of 1.16 mol dm⁻³ perchloric acid. The observed rate constant (k_obs) was 3.3 × 10⁻⁴ to 3.5 × 10⁻⁴ s⁻¹ and the half-life (t_1/2) was 33–35 min for chromium(VI). The effects of total [TritonX-100] and [H⁺] on the reaction rate were determined. Reducing nature of non-ionic TritonX-100 surfactant is found to be due to the presence of –OH group in the polyoxyethylene chain. It was observed that monomeric and non-ionic micelles of TritonX-100 were oxidized by chromium(VI). When [TritonX-100] was less than its critical micelle concentration (cmc) the k_obs values increased from 0.76 × 10⁻⁴ to 1.5 × 10⁻⁴ s⁻¹. As the [TritonX-100] was greater than the cmc, the k_obs values increases from 2.1 × 10⁻⁴ to 8.2 × 10⁻⁴ s⁻¹ in presence of constant [HClO₄] (1.16 mol dm⁻³) at 40 °C. A comparison was made of the oxidative degradation rates of TritonX-100 with different metal ion oxidants. The order of the effectiveness of different oxidants was as follows: permanganate > diperiodatoargentate(III) > chromium(VI) > cerium(IV).