正癸烷和正己烷气相氧化裂解过程的研究

采用石英管反应器,常压下研究了正癸烷和正己烷的气相氧化裂解（GOC）过程。实验结果表明,O2的存在降低了正癸烷GOC反应的活化能,使反应在较低的温度下具有高的反应性能;O2同时起到消除积炭的作用,提高体系的抗积炭能力。于热裂解反应相比,低温下正癸烷的GOC反应更适合制备液体组分,同时联产低碳烯烃。在600℃,碳氧摩尔比为2.5时,正癸烷的GOC反应可获得39.9％的低碳烯烃收率和30.0％的液体收率。对于直链烷烃的GOC反应,低温下O2主要进行氧化脱氢反应,高温下则更多的进行 CO x(x=1,2)的生成反应;和正己烷分子相比,相同反应条件下O2更容易引发正癸烷分子的部分氧化反应生成CO。     

Kinetic investigations on interaction of carbon monoxide with RuIICl2(PPh3)3 in mixed aqueous medium

Kinetics, equilibrium and thermodynamics of interaction of CO with RuCl₂(PPh₃)₃ (1) have been investigated in 1:1(v/v) water — 1,4-dioxan mixture in which 1 dissociates to RuCl₂(PPh₃)₂ (1a), by losing a coordinated PPh₃. The kinetics of complexation of (1a) with CO to form RuCl₂(CO)(PPh₃)₂ (2) indicated first order dependence in [1a] and [CO]. The thermodynamic parameters for the formation of 2 were determined.This revised version was published online in December 2005 with corrections to the Cover Date.     

Comparative study between gas phase and liquid phase for the production of DMC from methanol and CO2

Direct synthesis of dimethyl carbonate (DMC) from methanol and carbon dioxide over Co1.5PW12O40 in liquid and in gas phase is investigated. The synthesized catalyst has been characterized by means of FTIR and XRD. Liquid phase experiment results showed that high pressures are favorable for the synthesis of DMC. However, DMC formation is limited by the reaction with co-produced water. DMC selectivity is more strongly dependent on the temperature than on the pressure of CO2. As for the reactions in gas phase, it has been found that both CH3OH conversion and DMC selectivity decreased with increasing temperature, owing to the decomposition of DMC at high temperatures. High temperatures and more amount of Co1.5PW12O40 catalyst favor the formation of dimethoxymethane (DMM) and methyl formate (MF).     

Quantum yield of Cl* (2P1/2) production in the gas phase photolysis of CCl4 in the ultraviolet

In this paper, we have probed the dynamics of chlorine atom production from the gas phase photodissociation of carbon tetrachloride at 222 and 235 nm. The quantum yield, φ* of Cl* (²P_1/2) production has been determined by probing the nascent concentrations of both excited (²P_1/2) and ground state (²P_3/2) chlorine atoms by suitable resonance-enhanced multiphoton ionization (REMPI) detection schemes. Although at the photolysis wavelengths the absorption of carbon tetrachloride is weak, significant amounts of Cl* are produced. Surprisingly, the quantum yield of Cl* production does not follow the absorption spectrum closely, which gives rise to the possibility of an indirect dissociation mechanism present in CCl₄ along with direct dissociation at these ultraviolet wavelengths     

MgFe0.1Al1.9O4 的合成及其催化乙苯与 CO2 的氧化脱氢反应

 以柠檬酸为络合剂, 采用溶胶-凝胶法制备了具有尖晶石结构的 MgFe_0.1Al_1.9O₄ 催化剂, 并将其用于催化乙苯与 CO₂ 氧化脱氢反应. 运用 X 射线衍射、X 射线能量色散光谱分析、红外光谱、热重-差热、N₂ 吸附-脱附和 H₂ 程序升温还原等技术对催化剂进行了表征. 结果表明, 在 650 ºC 以上焙烧即可制得结构确定、组成均一的 Mg-Fe-Al-O 复合氧化物催化剂, 其中 Fe 物种主要以同晶取代的形式存在于尖晶石骨架中. 随着焙烧温度的升高, 尖晶石结晶度提高, Fe 物种还原能力下降, 催化剂晶粒度增大, 比表面积降低. 700 ºC 焙烧制备的 MgFe_0.1Al_1.9O₄ 具有较好的催化乙苯与 CO₂ 氧化脱氢反应活性和稳定性.     

Investigation of interaction of olefin-bonded transition metal complexes by gas chromatography. Diphenylphosphine complexes with CoCl2 and CoBr2

Summary Packings consisting of diphenylphosphine complexes with CoCl₂ and CoBr₂, chemically bonded to the silica surface, were synthesized and their retention parameters determined. The packings are capable of specifically interacting with electron-donating compounds by forming -complexes. The interaction is considerably stronger in the case of CoBr₂-containing packing than in the case of CoCl₂-containing packing.     

A parametric study of CO2/N2 gas separation membrane processes for post-combustion capture

Capture of CO₂ from flue gases produced by the combustion of fossil fuels and biomass in air is referred to as post-combustion capture. Chemisorbent processes are considered to be the most feasible method and are already at an advanced stage of development, but gas separation membranes are attracting more and more attention as a possible alternative. This paper describes a detailed parametric study of mass and energy balances for a simulated single membrane process. Typical operating conditions (CO₂ concentration in the flue gas, pressure and temperature, etc.) together with the influence of the membrane quality (permeability, selectivity) and membrane area on membrane performance (CO₂ separation degree and CO₂ purity) are simulated over a wide range of parameters.     

制备条件对Ni/ZrO2-SiO2催化剂煤气甲烷化的影响

采用浸渍法制备了ZrO₂-SiO₂复合载体和Ni质量分数为6%的Ni/ZrO₂-SiO₂催化剂,考察了载体制备时浸渍溶液pH值、焙烧温度和催化剂制备时的焙烧温度对Ni/ZrO₂-SiO₂催化剂煤气甲烷化反应性能的影响。采用X射线衍射、程序升温还原和扫描电子显微镜等方法对催化剂进行了表征。结果表明,载体浸渍溶液pH值为8.0～9.0, 载体焙烧温度为550 ℃,催化剂焙烧温度为450 ℃时,Ni/ZrO₂-SiO₂催化剂在煤气甲烷化反应中显示了最优的催化性能,CO转化率100%,CO₂转化率1.8%,CH₄生成速率16.6 mmol/(h·g)。进一步表征发现,制备ZrO₂-SiO₂复合载体时,增大浸渍溶液的pH值有利于形成粒径较小的亚稳态四方晶相ZrO₂,可见四方晶相ZrO₂更有利于甲烷化反应;载体焙烧温度会影响到NiO粒径的大小和其在催化剂表面的分散,温度过高和过低都会导致NiO粒径大小的不适宜以及分散性的降低;催化剂焙烧温度过高则会导致NiO与载体间的相互作用减弱,NiO分散性降低。     

The reaction of (SO2)2 and (CO2)2 with Ba

The reactions of (CO₂)₂ and (SO₂)₂ with Ba have been investigated using a crossed beam arrangement and the laser-induced fluorescence technique. Internal energy in the BaO product was probed in order to study differences between monomeric and dimeric reactions. The reaction cross section for the dimers of CO₂ was found to be between four and eightfold larger than that of the monomers. This can be explained by the change in the reaction mechanism due to the positive electron affinity of the dimers versus the negative electron affinity of the monomers. The product BaO from the dimeric reactions is much colder rotationally than in the monomeric case. This phenomenon can be explained based on the kinematics.     

光辐照驱动CH4-CO2重整中Ni/MgO-Al2O3催化活性吸收体的活性

将等离子体还原法和常规焙烧还原法制备的Ni基催化剂用于制备太阳能催化活性吸收体,在氙灯模拟的太阳光聚光反应系统中,考察了其催化CH4-CO2重整反应活性.结果表明,等离子体还原法制备的Ni/MgO-A12O3催化活性吸收体的低温活性最高,在光辐照平均能流密度为61 kW/m2,空速36 dm3/(g·h),CH4和CO...     

CO2 permeation properties of poly(ethylene oxide)-based segmented block copolymers

This paper discusses the gas permeation properties of poly(ethylene oxide) (PEO)-based segmented block copolymers containing monodisperse amide segments. These monodisperse segments give rise to a well phase-separated morphology, comprising a continuous PEO phase with dispersed crystallised amide segments. The influence of the polyether phase composition and of the temperature on the permeation properties of various gases (i.e., CO₂, N₂, He, CH₄, O₂ and H₂) as well as on the pure gas selectivities were studied in the temperature range of −5 °C to 75 °C. The CO₂ permeability increased strongly with PEO concentration, and this effect could partly be explained by the dispersed hard segment concentration and partly by the changing chain flexibility. By decreasing the PEO melting temperature the low temperature permeabilities were improved. The gas transport values were dependant on both the dispersed hard segment concentration and the polyether segment length (length between crosslinks). The gas selectivities were dependant on the polyether segment length and thus the chain flexibility.     

Influence of support on resistance to carbon-deposition of catalyst for CH4, CO2 with O2 to synthesis gas

In the reaction of catalytic oxidation of CH₄, CO₂ with O₂ to synthesis gas, carbon-deposition is an important factor for deactivation. By adding different oxides to Ni/Al₂O₃ catalyst, its resistance to carbon-deposition was improved. The experimental results indicate that the order of resistance to carbon-deposition is as follows: Ni/CaO-Al₂O₃>Ni/MgO-Al₂O₃>Ni/ TiO₂-Al₂O₃ > Ni/CeO₂-Al₂O₃>Ni/La₂O₃-Al₂O₃>Ni/Y₂O₃-Al₂O₃>Ni/Fe₂O₃-Al₂O₃>Ni/Al₂O₃. The catalysts were characterized by CO₂-TPD, O₂-TPD and XPS methods. Here the relation between the order of resistance to carbon-deposition and performance of catalyst is discussed.     

气相色谱-质谱表征甲醇制烯烃副产汽油中的C5～C7烯烃

采用气相色谱-质谱(GC-MS)对甲醇制烯烃(MTO)副产汽油中的C5~C7烯烃进行了详细的定性表征,对MTO副产汽油中的49个单烯烃、11个二烯烃和9个环烯烃共计69个C5~C7烯烃组分在聚甲基硅氧烷柱上的保留指数进行了测定和定性确认。根据GC-MS定性分析结果建立了MTO副产汽油中C5~C7烯烃的保留指数数据库,采用气相色谱对副产汽油中C5~C7烯烃组分进行了定量分析。定量结果表明:MTO汽油以C5~C7脂肪族烯烃为主,含有少量的二烯烃和环烯烃,烷烃和环烷烃含量很少。MTO副产汽油中C5~C7烯烃的详细表征为其综合利用提供了依据。     

Electrochemical reduction of CO2 with high current density in a CO2 + methanol medium II. CO formation promoted by tetrabutylammonium cation

The cation of the supporting electrolyte was found to play an important role in the electrochemical reduction of highly concentrated CO₂ in a CO₂ + methanol medium. Electroreduction of CO₂ with tetrabutylammonium (TBA) salts yielded CO as the main product, while methyl formate was predominantly formed when lithium salts were used as supporting electrolytes. The latter supporting electrolytes showed a higher overvoltage than the former. When TBA salt was used, the reduction of CO₂ was catalysed by TBA ion to yield CO^−.₂. This intermediate may be stabilized by forming an ion pair, {TBA⁺---CO^−.₂}, or by being adsorbed on the electrode surface as CO^−._2ad. Then CO^−.₂ reacts with CO₂ to produce CO. The hydrophobic atmosphere at the electrode provided by TBA ion may be adequate for CO production. Lithium ion, on the other hand, suppressed the reduction of CO₂.     

Metal(salen)-catalyzed oxidation of limonene in supercritical CO2

Summary The Mn(Salen)Cl and Ni(Salen)-catalyzed oxidation of limonene has been carried out. The catalytic cycle involved PhIO via a rebound mechanism. In all cases the use of organic solvents resulted in reasonable selectivities of oxidized products. The use of supercritical carbon dioxide (SCCO₂) led at least to comparable results in terms of conversions, but showed different selectivities. In ordinary solvents epoxidation appears to predominate over allylic oxidation. This tendency, in SCCO₂, appears only after 4 h of reaction. Shorter reaction times (2 h) appear to lead to opposite selectivity. These results showed the advantages of using SCCO₂ as solvent in these reactions. SCCO₂ is much more compatible with green technology than are organic solvents.     

Photocatalytic Synthesis of Hydrocarbon Oxygenates from C2H6 and CO2 over Pd-MoO3/SiO2 Catalyst

Pd-MoO3/SiO2 catalyst has been prepared using the method of incipient wetness impregnation. The photo absorbing behaviors and chemisorbing properties of the catalyst have been characterized by UV-vis spectra and TPD-MS experiments. The results indicated that metal Pd loaded on MoOe/SiO2 has a significant effect on the photo absorbing performance of MoO3/SiO2, and an obvious blue shift of the absorption edge is produced. Under UV irradiation, the chemisorption state of CO2 undergoes decomposing process to form CO at 481 K, and a two-site adsorption state of ethane can be formed at around 496 K. Photo-oxidation of ethane using carbon dioxide can mainly produce propanal, ethanol and acetaldehyde in the temperature range of 353-423 K. The presence of metal Pd improves the catalytic activity remarkably.     

镧石型碳酸镨钕向碱式碳酸镨钕的相转变反应特征及其应用

本文研究了镧石型碳酸镨钕[（PrNd）₂（CO₃）₃·8H₂O,LPN]在95℃的不同起始pH值的溶液中陈化不同时间所得样品的XRD衍射图,证明所得样品为碱式碳酸镨钕[（PrNd）（OH）（CO₃）,BPN]。为此,详细研究了这一相态转变的反应条件以及粒子特征变化。结果表明：LPN是由片状或条状结晶连生而成的聚集体,具有大的粒度和小的堆密度。当在热的水溶液中陈化时,由于水解反应而发生由LPN向BPN的相转变。这一相转变可以在95℃下pH=7以上的溶液中发生,其转化率随起始溶液pH值的升高和陈化时间的延长而增大。随着相转变的进行,溶液的pH值开始下降明显,而后趋于平缓。相应地,大的团聚体颗粒解散成小的单个粒子,导致粒度减小,分布变窄,氯根含量降低和堆密度的增大。而且,这些变化直接与溶液pH值和陈化时间相关。据此,发展了一种新的制备具有高堆密度、低氯根含量、细粒度和窄分布的新方法,而且通过改变相转变条件可以方便地调谐颗粒特征。     

镧石型碳酸镨钕向碱式碳酸镨钕的相转变反应特征及其应用

镧石型碳酸镨钕[(PrNd)2(CO3)3·8H2O,LPN]在95℃的不同起始pH值的溶液中陈化不同时间所得样品的XRD衍射图证明了LPN向碱式碳酸镨钕[(PrNd)(OH)(CO3),BPN]的相态转变。为此,详细研究了这一相态转变的反应条件以及粒子特征变化。结果表明:LPN是由片状或条状结晶连生而成的聚集体,具有大的粒度和小的堆密度。当在热的水溶液中陈化时,由于水解反应而发生由LPN向BPN的相转变。这一相转变可以在95℃下pH=7以上的溶液中发生,其转化率随起始溶液pH值的升高和陈化时间的延长而增大。随着相转变的进行,溶液的pH值开始下降明显,而后趋于平缓。相应地,大的团聚体颗粒解散成小的单个粒子,导致粒度减小,分布变窄,氯根含量降低和堆密度的增大。而且,这些变化直接与溶液pH值和陈化时间相关。据此,发展了一种新的制备具有高堆密度、低氯根含量、细粒度和窄分布的新方法,而且通过改变相转变条件可以方便地调谐颗粒特征。     

纳米Li_2ZrO_3吸收剂原位移除CO_2强化水煤气变换反应制氢

采用浸渍法制备了在水煤气变换(WGS)反应中具有高催化活性的Ni/γ-Al2O3催化剂,使用柠檬酸法合成出高效CO2吸收剂Li2ZrO3纳米材料.在固定床微反应器上对WGS和吸附强化水煤气变换(SE-WGS)反应制氢过程进行了比较研究.前者只使用20%Ni/γ-Al2O3催化剂,而后者将20%Ni/γ-Al2O3催化剂与纳米Li2ZrO3吸收剂混合装填.结果表明,纳米Li2ZrO3具有比已报道的CO2吸收剂更快的吸收速率及优异的吸脱附循环稳定性,可应用于吸附强化过程,通过原位吸收WGS反应产生的CO2,使得反应超越化学平衡限制,直接制得高纯度H2.在823K,0.1MPa和H2O/CO=4的条件下,在SE-WGS过程一步制得纯度高于98%的H,验证了吸附强化反应进程制高纯氢的可行性.     

Simulation of dielectric properties and stability of clusters (H2O)i, CO2(H2O)i, and CH4(H2O)i

Molecular dynamics method is used for studying complex permittivity ɛ and the stability of individual water clusters as a function of the number of involved molecules (7 ≤ i ≤ 20) and also the corresponding characteristics of water aggregates with a captured CO₂ or CH₄ molecule. Absorption of the latter molecules leads to considerable changes in dielectric properties and stability of clusters. In particular, upon the addition of a CO₂ molecule to a water cluster, the oscillation parameters of the real and imaginary parts of the permittivity change. Capture of a CH₄ molecule by a water aggregate changes the ɛ(ω) dependence from the relaxation to resonance type. For i ≥ 15, the thermal stability of individual water clusters can be lower than that of aggregates CO₂(H₂O) _i and CH₄(H₂O) _i . The mechanical stability of (H₂O) _{i ≥ 13} clusters can exceed that of heteroclusters under consideration. Clusters (H₂O) _i and CO₂(H₂O) _i have approximately the same dielectric stability, whereas aggregates CH₄(H₂O) _i exhibit lower stability with respect to electric perturbations. Original Russian Text ? A.E. Galashev, V.N. Chukanov, A.N. Novruzov, O.A. Novruzova, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 2, pp. 143–153.