Simultaneous determination of cadmium and lead in wine by electrothermal atomic absorption spectrometry

A method has been developed for the direct simultaneous determination of Cd and Pb in white and red wine by electrothermal atomic absorption spectrometry (ET-AAS) using a transversely heated graphite tube atomizer (THGA) with longitudinal Zeeman-effect background correction. The thermal behavior of both analytes during pyrolysis and atomization stages were investigated in 0.028 mol l⁻¹ HNO₃ and in 1+1 v/v diluted wine using mixtures of Pd(NO₃)₂+Mg(NO₃)₂ and NH₄H₂PO₄+Mg(NO₃)₂ as chemical modifiers. With 5 μg Pd+3 μg Mg as the modifiers and a two-step pyrolysis (10 s at 400°C and 10 s at 600°C), the formation of carbonaceous residues inside the atomizer was avoided. For 20 μl of sample (wine+0.056 mol l⁻¹ HNO₃, 1+1, v/v) dispensed into the graphite tube, analytical curves in the 0.10–1.0 μg l⁻¹ Cd and 5.0–50 μg l⁻¹ Pb ranges were established. The characteristic mass was approximately 0.6 pg for Cd and 33 pg for Pb, and the lifetime of the tube was approximately 400 firings. The limits of detection (LOD) based on integrated absorbance (0.03 μg l⁻¹ for Cd, 0.8 μg l⁻¹ for Pb) exceeded the requirements of Brazilian Food Regulations (decree #55871 from Health Department), which establish the maximum permissible level for Cd at 200 μg l⁻¹ and for Pb at 500 μg l⁻¹. The relative standard deviations (n=12) were typically <8% for Cd and <6% for Pb. The recoveries of Cd and Pb added to wine samples varied from 88 to 107% and 93 to 103%, respectively. The accuracy of the direct determination of Cd and Pb was checked for 10 table wines by comparing the results with those obtained for digested wine using single-element ET-AAS, which were in agreement at the 95% confidence level.     

Determination of lead in blood by tungsten coil electrothermal atomic absorption spectrometry

A method for the determination of lead in blood using a tungsten coil atomizer is described. A 100 μl volume of the whole blood sample is transferred to a sampler cup containing 100 μl of water plus 300 μl of 0.25% v/v Triton X-100. After lysis of blood cells, 500 μl of 10% w/v trichloroacetic acid is added for protein precipitation and 10 μl of the supernatant solution is automatically delivered into the tungsten coil. The furnace heating program is implemented in 41 s. It is shown by the paired t-test that there is no significant difference at the 5% probability level between results obtained by the proposed method and by using a transversely heated graphite atomizer with a longitudinal Zeeman background correction. Accuracy is also assessed by employing reference materials. The proposed tungsten coil procedure presents a characteristic mass of 15 pg Pb and a detection limit of 1.9 μg Pb dl⁻¹.     

Determination of cadmium by electrothermal atomic absorption spectrometry using electrochemical separation in a microcell

Electrodeposition on the graphite electrode under conditions of controlled current in a flow-through mode, followed by electrothermal atomic absorption spectrometry, is proposed for the determination of cadmium. After electrolysis in a microcell of 2.6 μl volume, deposited metal was dissolved in 40 μl 0.2 mol l⁻¹ HNO₃ and the whole volume was direct injected into the atomizer. Using this on-line arrangement and electrodeposition from 1.75 ml of sample solution detection limit of 25 ng l⁻¹ Cd was attained. The method was applied for the determination of cadmium in a real sample of seawater.     

A new strategy for preparation of hair slurries using cryogenic grinding and water-soluble tertiary-amines medium

The investigation of trace metal contents in hair can be used as an index of exposure to potentially toxic elements. Direct determination of Cd, Cu and Pb in slurries of hair samples was investigated using an atomic absorption spectrometer with Zeeman-effect background correction. The samples were pulverized in a freezer/mill for 13 min, and hair slurries with 1.0 g l⁻¹ for the determination of Cu and Pb, and 5.0 g l⁻¹ for the determination of Cd, respectively, were prepared in three different media: 0.1% v/v Triton X-100, 0.14 mol l⁻¹ HNO₃, and 0.1% v/v of CFA-C, a mixture of tertiary amines. The easiest way to manipulate the hair samples was in CFA-C medium. The optimum pyrolysis and atomization temperatures were established with hair sample slurries spiked with 10 μg l⁻¹ Cd²⁺, 30 μg l⁻¹ Pb²⁺, and 10 μg l⁻¹ Cu²⁺. For Cd and Pb, Pd was used as a chemical modifier, and for Cu no modifier was needed. The analyte addition technique was used for quantification of Cd, Cu, and Pb in hair sample slurries. A reference material (GBW076901) was analyzed, and a paired t-test showed that the results for all elements obtained with the proposed slurry sampling procedure were in agreement at a 95% confidence level with the certified values. The cryogenic grinding was an effective strategy to efficiently pulverize hair samples.     

Direct determination of lead in sweet fruit-flavored powder drinks by electrothermal atomic absorption spectrometry

A simplified method for direct determination of lead in sweet fruit-flavored powder drinks, syrups and honeys by electrothermal atomic absorption spectrometry without sample digestion is proposed. Samples were dissolved in water, acidified to 0.2% (v/v) HNO₃, and directly injected into an end-capped transversely heated graphite atomizer (THGA). Building up of carbonaceous residue inside the atomizer was effectively precluded for sugar solutions not exceeding 8.0% (m/v) when a heating program with two pyrolysis steps (600 and 1000°C) was carried out without air-ashing. Under these conditions one atomizer supported about 250 firings. Among various chemical modifiers tested, better recovery and repeatability results were obtained with a 5 μg Pd + 3 μg Mg(NO₃)₂ mixture. Tests carried out with individual concomitants containing up to 1.0 μg Na, K, Ca or Cl, and up to 10.0 μg phosphate or sulphate, and several mixtures of these six concomitants, did not reveal significant interferences on lead atomization. Characteristic mass and detection limit based on integrated absorbance were 15 and 11 pg Pb, respectively. The relative standard deviation based on 10 measurements for typical samples (20–60 ng g⁻¹ Pb) was always lower than 5.5%. The detection limit of 7.0 ng g⁻¹ Pb attained the Codex recommendation for the maximum allowed lead contents in the sugar samples. Application of t-test to the results obtained by the proposed direct analysis, and the official method adopted by Food Chemical Codex, demonstrated that there were no significant differences at the 5% probability level.     

Evaluation of electrodeposited tungsten chemical modifier for direct determination of chromium in urine by ETAAS

The direct determination of chromium in urine by electrothermal atomic absorption spectrometry (ETAAS) using graphite tubes modified with tungsten is proposed. Modification of the graphite is made by tungsten electrodeposition over the whole surface atomizer followed by carbide formation by heating the tube inside its own furnace. For tungsten electrocoating, the graphite tube and a platinum electrode were connected to a power supply as cathode and anode, respectively, and immersed in a solution containing 2 mg of W in 0.1% v/v HNO₃. Then, 5 V was applied between the electrodes during 20 min for tungsten electrodeposition over the whole atomizer. A SpectrAA 220 Varian atomic absorption spectrometer equipped with a deuterium background corrector was used throughout. Undiluted urine (20 μl) was delivered over the tungsten-treated tube and the chromium-integrated absorbance was measured after applying a suitable heating program with maximum pyrolysis at 1300 °C and atomization at 2500 °C. With electrodeposited tungsten modifier, the tube lifetime increased up to four times when compared to previous published methods for Cr determination in urine by ETAAS, reaching 800 firings. Method detection limit (3 S.D.) was 0.10 μg l⁻¹, based on 10 integrated absorbance measurements of a urine sample with low Cr concentration. Two reference materials of urines (SRM 2670) from National Institute of Standards and Technology (NIST) were analyzed for method validation. For additional validation, results obtained from eight human urine samples were also analyzed in a spectrometer with Zeeman effect background correction.     

Electrothermal atomic absorption spectrometry determination of molybdenum in whole blood

A method for the determination of molybdenum in whole blood by atomic absorption spectrometry with electrothermal atomization was developed and evaluated. Erbium (25 μg) was chosen from several potential chemical modifiers (Sm, Lu, Ho, Eu and Pd+Mg) as the most appropriate for the sensitive and reliable determination of molybdenum in such sample. The process used was direct dilution of the sample in a ratio 1:2 with a 0.1% (v/v) Triton X-100 solution. The injection of 20 μl of a solution of 15% (w/v) hydrogen peroxide and running the temperature program after 5 firings greatly reduced the effect of build-up of carbonaceous residues within the atomizer. The limit of detection and working ranges, respectively, were 0.6 and 2.0–100.0 μg l⁻¹, and the characteristic mass was 7.2 pg. The relative standard deviation varied from 0.8 to 1.5% for within and between batch determinations, respectively. The determination of molybdenum in Seronorm™ Trace Elements in Whole Blood with known added amounts of the analyte was performed to asses the accuracy. The optimized procedure has been applied to the determination of molybdenum in whole blood specimens of 20 subjects taken before and 10–12 h after receiving an over-supply of 1 mg of molybdenum. The molybdenum concentrations (±S.D.) were 10.9±0.4 μg Mo l⁻¹ (range 9.9–11.6 μg Mo l⁻¹) and 15.4±0.4 μg Mo l⁻¹ (range 13.1–16.9 μg Mo l⁻¹) for the individuals before and after the administration of molybdenum.     

Inductively coupled plasma-atomic emission spectrometry method for determination of trace metals in alkaline-earth matrices after flotation separation

An inductively coupled plasma-atomic emission spectrometry (ICP-AES) method is developed for determination of Cd, Co, Cr, Cu, Ni, Tl and Zn in traces in calcite, CaCO₃, dolomite, CaMg(CO₃)₂, and gypsum, CaSO₄. Interferences of a Ca/Mg matrix on analyte intensities were investigated. The results reveal that Ca does not interfere with Cr, Ni and Zn, but tends to decrease the intensity of the other elements. Magnesium as a matrix element does not interfere on with Zn, but increases the intensities of Ni, Cr and Cu, and decreases the intensities of Cd, Co and Tl. To eliminate these matrix interferences on trace element intensities, a flotation separation method is proposed. Lead(II) hexamethylenedithiocarbamate, Pb(HMDTC)₂, is applied as a collector for flotation of trace elements from acidic solutions of mineral samples. The flotation of acidic aqueous solutions of calcite, dolomite and gypsum was performed at pH 6.0, using 10 mg l⁻¹ Pb and 0.3 mmol l⁻¹ HMDTC⁻ added to 1 l of solution tested. The method detection limits of analytes in different minerals range from 0.02 to 0.06 μg g⁻¹ for Cd, 0.04 to 0.10 μg g⁻¹ for Co, 0.03 to 0.13 μg g⁻¹ for Cr, 0.02 to 0.16 μg g⁻¹ for Cu, 0.09 to 0.30 μg g⁻¹ for Ni, 6.45 to 7.71 μg g⁻¹ for Tl and 0.18 to 0.20 μg g⁻¹ for Zn.     

Determination of cadmium and lead at low levels by using preconcentration at fullerene coupled to thermospray flame furnace atomic absorption spectrometry

A new and sensitive method for Cd and Pb determinations, based on the coupling of thermospray flame furnace atomic absorption spectrometry and a preconcentrator system, was developed. The procedure comprised the chelating of Cd and Pb with ammonium pyrrolidinedithiocarbamate with posterior adsorption of the chelates on a mixture (40 mg) of C₆₀ and C₇₀ at a flow rate of 2.0 ml min⁻¹. These chelates were eluted from the adsorbent by passing a continuous flow of ethanol (80% v/v) at 0.9 ml min⁻¹ to a nickel tube placed in an air/acetylene flame. After sample introduction into the tube by using a ceramic capillary (0.5 mm i.d.), the analytical signals were registered as peak height. Under these conditions, improvement factors in detectability of 675 and 200 were obtained for Cd and Pb, respectively, when compared to conventional flame atomic absorption spectrometry. Spiked samples (mineral and tap waters) and drinking water containing natural concentrations of Cd were employed for evaluating accuracy by comparing the results obtained from the proposed methodology with those using electrothermal atomic absorption spectrometry. In addition, certified reference materials (rye grass, CRM 281 and pig kidney, CRM 186) were also adopted for the accuracy tests. Due to the good linearity ranges for Cd (0.5–5.0 μg l⁻¹) and Pb (10–250 μg l⁻¹), samples with different concentrations could be analyzed. Detection limits of 0.1 and 2.4 μg l⁻¹ were obtained for Cd and Pb, respectively, and RSD values <4.5% were observed (n=10). Finally, a sample throughput of 24 determinations per hour was possible.     

Direct determination of Cu,Mn, Pb,and Zn in beer by thermospray flame furnace atomic absorption spectrometry

In this work, thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) was employed for Cu, Mn, Pb, and Zn determination in beer without any sample digestion. The system was optimized and calibration was based on the analyte addition technique. A sample volume of 300 μl was introduced into the hot Ni tube at a flow-rate of 0.4 ml min⁻¹ using 0.14 mol l⁻¹ nitric acid solution or air as carrier. Different Brazilian beers were directly analyzed after ultrasonic degasification. Results were compared with those obtained by graphite furnace atomic absorption spectrometry (GFAAS). The detection limits obtained for Cu, Mn, Pb, and Zn in aqueous solution were 2.2, 18, 1.6, and 0.9 μg l⁻¹, respectively. The relative standard deviations varied from 2.7% to 7.3% (n=8) for solutions containing the analytes in the 25–50 μg l⁻¹ range. The concentration ranges obtained for analytes in beer samples were: Cu: 38.0–155 μg l⁻¹; Mn: 110–348 μg l⁻¹, Pb: 13.0–32.9 μg l⁻¹, and Zn: 52.7–226 μg l⁻¹. Results obtained by TS-FF-AAS and GFAAS were in agreement at a 95% confidence level. The proposed method is fast and simple, since sample digestion is not required and sensitivity can be improved without using expensive devices. The TS-FF-AAS presented suitable sensitivity for determination of Cu, Mn, Pb, and Zn in the quality control of a brewery.     

Indirect determination of iodide by tungsten coil atomic emission spectrometry

The spectroscopic determination of iodide is a difficult challenge, especially in small sample volumes. The strongest transition lines for this element lie in the vacuum ultraviolet region of the spectrum, so most conventional instruments produce very weak signals. This work describes a tungsten coil atomic emission procedure for the indirect determination of iodide. A 25 μl aliquot of a solution containing a known amount of indium is deposited on the tungsten coil and dried with a simple heating program. Once the coil is dry, 25 μl of an iodide solution is added to the coil. The solution is dried and vaporized at high current. The atomic emission signal for In at 451.1 nm is monitored. In the presence of iodide, InI is formed and the In emission signal is attenuated. This attenuation is proportional to iodide concentration with a method detection limit of 0.6 mg l^{− 1} iodide using an In concentration of 10 mg l^{− 1}, and 3 mg l^{− 1} iodide using an In concentration of 50 mg l^{− 1}. Linear calibration curves span a range of two orders of magnitude. Analysis of a deionized water sample spiked with 50 mg l^{− 1} iodide gives a recovery of 100% and a precision of 5.5% relative standard deviation. Analysis of a tap water sample spiked with 50 mg l^{− 1} iodide gives a recovery of 140% and a precision of 7.1% relative standard deviation. The poor accuracy for the tap water analysis may arise from the reaction of In with other halides in the sample. This is the first report of determination of a halogen using the tungsten coil atomizer.     

Preconcentration procedure using cloud point extraction in the presence of electrolyte for cadmium determination by flame atomic absorption spectrometry

This paper describes a micelle-mediated phase separation in the presence of electrolyte as a preconcentration method for cadmium determination by flame atomic absorption spectrometry (FAAS). Cadmium was complexed with ammonium O,O-diethyldithiophosphate (DDTP) in an acidic medium (0.32 mol l^− 1 HCl) using Triton X-114 as surfactant and quantitatively extracted into a small volume (about 20 μl) of the surfactant-rich phase after centrifugation. The chemical variables that affect the cloud point extraction, such as complexing time (0–20 min), Triton X114 concentration (0.043–0.87% w/v) and complexing agent concentration (0.01–0.1 mol l^− 1), were investigated. The cloud point is formed in the presence of NaCl at room temperature (25 °C), and the electrolyte concentration (0.5–5% w/v) was also investigated. Under optimized conditions, only 8 ml of sample was used in the presence of 0.043% w/v Triton X-114 and 1% (w/v) NaCl. This method permitted limits of detection and quantification of 0.9 μg l^− 1 and 2.9 μg l^− 1 Cd, respectively, and a linear calibration range from 3 to 400 μg l^− 1 Cd. The proposed method was applied to Cd determination in physiological solutions (containing 0.9% (w/v) of NaCl), mineral water, lake water and cigarette samples (tobacco).     

Flow-through sensors for enhancing sensitivity and selectivity of FTIR spectroscopy in aqueous media

The principle of novel flow-through sensor systems with FTIR spectroscopic detection is presented on the example of the determination of organic acids in aqueous solution. The constructed flow-through sensor system is based on trapping of derivatized porous polymer beads in a conventional IR transmission cell and integration of the flow cell into a sequential injection (SI) manifold. By the SI-manifold sample pre-conditioning, sample-sensor interaction and sensor regeneration were performed in an automated and highly reproducible way. The polymer beads used in this study contained anion exchanger groups so that negatively charged molecules such as organic acids present in the anionic form could selectively interact with the polymer beads. Upon pumping a sample through the sensor cell organic acids were retained on the polymer beads whereas non-ionic matrix molecules passed hence allowing to separate the target analytes form the matrix. Apart from that the organic acids were also concentrated onto the polymer beads so that absolute analyte amounts in the low μg range could easily be detected. Linear calibration curves from 0 to 1 mmol l⁻¹ were recorded for acetic and malic acid using a sample volume of 500 μl (s_x0: 0.032 mmol l⁻¹ acetic acid and 0.031 mmol l⁻¹ malic acid). Mixtures of both acids were analyzed as well and it could be shown that by application of multivariate data evaluation procedures (PLS) simultaneous quantification of both acids could be performed successfully using the developed flow-through sensor system.     

Semi-online preconcentration of Cd, Mn and Pb on activated carbon for GFASS

This paper presents a method whereby trace elements in NH₄Cl-NH₃ medium are adsorbed on activated carbon in a micro-flow-injection (FI) semi-online sorbent extraction preconcentration system and then determined by graphite furnace atomic absorption spectrometry (GFAAS). The analytical performance of the proposed method for determining Cd, Mn and Pb was studied. A microcolumn packed with activated carbon was used as a preconcentration column (PCC). The metals to be determined were preconcentrated onto the column for 60 s and then rinsed with 0.02% (v/v) HNO₃ and eluted with 30 μl of 2 mol l⁻¹ HNO₃. Compared with the direct injection of 30 μl of aqueous sample solution, enrichment factor of 32, 26, and 21 and detection limits (3σ) of 0.4, 4.7, and 7.5 ng l⁻¹ for Cd, Mn and Pb, respectively, were obtained with 60 s sample loading at 3.0 ml min⁻¹ for sorbent extraction, 30 μl of eluate injection, and peak area measurement. The precisions (RSD, n=6) were 2.8% at the 0.05 μg l⁻¹ level for Cd, 3.0% at the 0.3 μg l⁻¹ level for Mn, and 3.1% at the 0.5 μg l⁻¹ level for Pb. The experimental results indicate that the procedure can eliminate the fundamental interferences caused by alkali and alkaline earth metals and the application of it to the determination of Cd, Mn and Pb in some water samples is successful.     

Sensitive Electrochemical Detection of Pb(II) and H2O2 via a Dual-functional Sn-doped Defective Bi2S3 Microspheres

In this work, a dual-functional electrochemical sensor has been proposed based on Sn-doped defective Bi₂S₃ (TDDB) microspheres, which exhibited the excellent electrochemical performance on Pb(II) and H₂O₂ detection. The TDDB offered a satisfied detection limit of 8.0 nM towards Pb(II) with a sensitivity of 96.7 μA ⋅ μM⁻¹. As a H₂O₂ sensor, a high sensitivity of 3540 μA mM⁻¹ cm⁻² was obtained in a linear range from 0.45 mM to 10 mM with a detection limit of 10 nM. Moreover, the electrochemical detection of Pb(II) in Taihu Lake and H₂O₂ in human serum was achieved with high reliability and good recovery.     

Advances with tungsten coil atomizers: Continuum source atomic absorption and emission spectrometry

Two new tungsten coil spectrometers are described: a continuum source tungsten coil atomic absorption spectrometer and a tungsten coil atomic emission spectrometer. Both devices use a 150 W tungsten coil extracted from a slide projector bulb. The power is provided by a computer-controlled, solid state, constant current 0–10 A supply. The heart of the optical system is a high-resolution spectrometer with a multi-channel detector. The continuum source system employs xenon or deuterium lamps, and is capable of multi-element analyses of complex samples like engine oil, urine, and polluted water. Spiked engine oil samples give mean percent recoveries of 98 ± 9, 104 ± 9, and 93 ± 0.8 for Al, V, and Ni, respectively. Copper, Zn, and Cd are determined in urine samples; while Cd, Co, Yb, and Sr are determined in water samples. Detection limits for Cd, Zn, Cu, Yb, Sr, and Co are: 8, 40, 1, 4, 1, and 4 μg l^− 1. The technique of tungsten coil atomic emission spectrometry using a 150 W commercial projector bulb is reported for the first time. Calcium, Ba, and Sr are determined with detection limits of 0.01, 0.5, and 0.1 μg l^− 1. Relative standard deviations are lower than 10% in each case, and Sr is determined in two water standard reference materials.     

Silica Gel-Immobilized 5-aminoisophthalohydrazide: A novel sorbent for solid phase extraction of Cu,Zn and Pb from natural water samples

A novel silica sorbent, silica gel-immobilized 5-aminoisophthalohydrazide (SiO₂-APH), was prepared by the condensation of 3-chloropropyl-functionalized silica gel with 5-aminoisophthalohydrazide (APH) derived from dimethyl 5-aminoisophthalate as a starting material and used for separation and preconcentration of Cu, Zn, and Pb metals in water samples using Flame Atomic Absorption Spectrometry (FAAS). The characterization of the new sorbent was carried out by Elemental Analysis, Thermogravimetric Analysis (TGA) and Fourier Transform Infrared Spectroscopy (FTIR). Important analytical parameters including as pH, amount of sorbent, type and amount of eluting solvent, sample volume, vortex and ultrasonic bath time, matrix ions that effect the developed SiO₂-APH-solid phase extraction (SPE) method were investigated and optimum parameters were detected. Recoveries of examined metals were obtained as 98% for Cu and Pb and 101% for Zn. The relative standard deviation (RSD, n = 8) of Cu, Zn and Pb metals were 3.2, 2.8 and 1.6%, respectively. Limit of detections (LODs) (n = 10) were found as 2.7 μg L⁻¹ for Cu, 7.4 μg L⁻¹ for Zn and 3.5 μg L⁻¹ for Pb μg L⁻¹. The accuracy of the new method was assessed by analyzing of TMDA-51.4 and TMDA-70.2 certified reference materials. The results obtained for metals were in a good agreement with certified values. Addition/recovery test was applied to the real well, river, dam and stream water samples to check the accuracy of the method. The results showed that the developed SiO₂-APH-SPE method can be effectively used as an alternative method for determination of Cu, Zn, and Pb metals in water samples.     

The determination of molybdenum and tungsten in sea and surface water

A simple method for the determination of molybdenum and tungsten in sea and surface water is presented. Molybdenum and tungsten are concentrated on activated charcoal by adsorption as the ammonium pyrrolidine dithiocarbamate complex; the optimal pH for adsorption is 1.3. Mo and W are then determined by thermal neutron activation, forming ⁹⁹Mo (T_{$\text{1}\text{2}$} = 66.7 h) and ¹³⁷W (T_{$\text{1}\text{2}$} = 23.8 h), respectively. The ^99mTc daughter of ⁹⁹Mo is measured as soon as the equilibrium between ^99mTc(T_{$\text{1}\text{2}$}= 6 h) and ⁹⁹Mo is established. The detection limits are 0.05 μg Mo l^-1 and 0.05 μg W l^-1 (or 0.001 μg W l^-1 after a simple chemical separation).     

A new atomization cell for trace metal determinations by tungsten coil atomic spectrometry

A new metallic atomization cell is used for trace metal determinations by tungsten coil atomic absorption spectrometry and tungsten coil atomic emission spectrometry. Different protecting gas mixtures are evaluated to improve atomic emission signals. Ar, N₂, CO₂ and He are used as solvents, and H₂ and C₂H₂ as solutes. A H₂/Ar mixture provided the best results. Parameters such as protecting gas flow rate and atomization current are also optimized. The optimal conditions are used to determine the figures of merit for both methods and the results are compared with values found in the literature. The new cell provides a better control of the radiation reaching the detector and a small, more isothermal environment around the atomizer. A more concentrated atomic cloud and a smaller background signal result in lower limits of detection using both methods. Cu (324.7 nm), Cd (228.8 nm) and Sn (286.3 nm) determined by tungsten coil atomic absorption spectrometry presented limits of detection as low as 0.6, 0.1, and 2.2 μg L⁻¹, respectively. For Cr (425.4 nm), Eu (459.4 nm) and Sr (460.7 nm) determined by tungsten coil atomic emission spectrometry, limits of detection of 4.5, 2.5, and 0.1 μg L⁻¹ were calculated. The method is used to determine Cu, Cd, Cr and Sr in a water standard reference material. Results for Cu, Cd and Cr presented no significant difference from reported values in a 95% confidence level. For Sr, a 113% recovery was obtained.     

Evaluation of tungsten–rhodium coating on an integrated platform as a permanent chemical modifier for cadmium,lead, and selenium determination by electrothermal atomic absorption spectrometry

A tungsten–rhodium coating on the integrated platform of a transversely heated graphite atomizer is proposed as a permanent chemical modifier for the determination of Cd, Pb, and Se by electrothermal atomic absorption spectrometry. It was demonstrated that coating with 250 μg W+200 μg Rh is as efficient as the conventional Mg(NO₃)₂+NH₄H₂PO₄ or Pd+Mg(NO₃)₂ modifiers for avoiding most serious interferences. The permanent W–Rh modifier remains stable for 300–350 firings of the furnace, and increases tube lifetime by 50%–100% when compared to pyrolytic carbon integrated platforms. Also, there is less degradation of sensitivity during the atomizer lifetime when compared with the conventional modifiers, resulting in a decreased need of re-calibration during routine analysis. The characteristic masses and detection limits achieved using the permanent modifier were respectively: Cd 1.1±0.4 pg and 0.020 μgL⁻¹; Pb 30±3 pg and 0.58 μgL⁻¹ and Se 42±5 pg and 0.64μgL⁻¹. Results from the determination of these elements in water reference materials were in agreement with the certified values, since no statistical differences were found by the paired t-test at the 95% level.