Centrifugal force spinning (CFS), also known as centrifugal spinning, forcespinning, or rotary jet spinning, provides considerably higher production rates than electrospinning (ES), but the more widespread use of CFS as an alternative depends on the ability to produce fibers with robust thermal and mechanical properties. Here, we report the CFS of poly(ethylene oxide) (PEO) fibers made using a spinning dope formulated with acetonitrile (AcN) as the volatile solvent, and we describe the thermal and mechanical properties of the centrifugally-spun fibers. Even though the formation, diameter, and morphology of electrospun and centrifugally-spun PEO fibers are relatively well-studied, the article presents three crucial contributions: the pioneering use of PEO solutions in AcN as spinning dope, characterization of crystallinity and mechanical properties of the centrifugally-spun PEO fibers, and a comparison with the corresponding properties of electrospun fibers. We find that fiber formation occurrs for the chosen CFS conditions if polymer concentration exceeds the entanglement concentration, determined from the measured specific viscosity. Most significantly, the centrifugally spun PEO fibers display crystallinity, modulus, elongation-at-break, and fiber diameter that rival the properties of electrospun PEO fibers reported in the literature. 相似文献
A series of multi-block copolymers, poly(L-lactide)-b-poly (?-caprolactone) (PLLA-b-PCL) were synthesized. The first step of the synthesis consisted of the transesterification between the PLLA and 1,4-Butanediol, followed by the copolymerization of PLLA-diols and PCL, using isophorone diisocyanate (IPDI) as a coupling agent. The synthesized polymers were characterized by Fourier transform infrared (FTIR) spectra, differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WAXD). PLLA/PCL block copolymers were electrospun into ultrafine fibers. The morphology of the electrospun fibrous scaffolds were investigated by Scanning Electron Microscopy (SEM). Results showed that the morphology and diameter of the fibers were affected by the electrospinning solution concentrationan and different weight ratio of PLLA/PCL. These electrospun PLLA-b-PCL fibrous membranes exhibited good flexibility and deformability. In comparison with the electrospun PLLA membrane, the electrospun fibrous membranes of PLLA-b-PCL demonstrated an enhanced elongation with still high tensile strength and Young's modulus to be beneficial for tissue engineering scaffolds. 相似文献
Biodegradable cell‐incorporated scaffolds can guide the regeneration process of bone defects such as physiological resorption, tooth loss, and trauma which medically, socially, and economically hurt patients. Here, 0, 5, 10, and 15 wt% fluoridated hydroxyapatite (FHA) nanoparticles containing 25 wt% F? and 75 wt% OH? were incorporated into poly(ε‐caprolactone) (PCL) matrix to produce PCL/FHA nanocomposite scaffolds using electrospinning method. Then, scanning electron microscopy (SEM), X‐ray diffraction (XRD) pattern, and Fourier transform infrared spectroscopy (FTIR) were used to evaluate the morphology, phase structure, and functional groups of prepared electrospun scaffolds, respectively. Furthermore, the tensile strength and elastic modulus of electrospun scaffolds were investigated using the tensile test. Moreover, the biodegradation behavior of electrospun PCL/FHA scaffolds was studied by the evaluation of weight loss of mats and the alternation of pH in phosphate buffer saline (PBS) up to 30 days of incubation. Then, the biocompatibility of prepared mats was investigated by culturing MG‐63 osteoblast cell line and performing MTT assay. In addition, the adhesion of osteoblast cells on prepared electrospun scaffolds was studied using their SEM images. Results revealed that the fiber diameter of prepared electrospun PCL/FHA scaffolds alters between 700 and 900 nm. The mechanical assay illustrated the mat with 10 wt% FHA nanoparticles revealed the highest tensile strength and elastic modulus. The weight loss alternation of mats determined around 1% to 8% after 30 days of incubation. The biocompatibility and cell adhesion of mats improved by increasing the amounts of FHA nanoparticles. 相似文献
Summary: A method to measure the Young's modulus of a single electrospun polyacrylonitrile (PAN) fiber is reported. The Young's modulus can be calculated from the force‐displacement curves obtained by the bending of a single fiber attached to an atomic force microscopy (AFM) cantilever. It is suggested that the high modulus of electrospun fibers is caused by the orientation of molecular chains, which is confirmed by wide‐angle X‐ray diffraction (WAXD) measurements. The communication will provide a basic understanding of the relationship between mechanical properties and structures of electrospun fibers.
A PAN fiber was attached to a contact mode cantilever to facilitate the measurement of force‐displacement curves and Young's modulus. 相似文献
Electrospinning is one of most versatile process to fabricate porous scaffolds in biomedical field. Synthetic polymers such as polycaprolactone (PCL) and polymethyl methacrylate (PMMA) provide excellent properties for biomedical applications due to their biocompatibility and tunable mechanical properties. PCL-PMMA electrospun blends combine compressive/tensile properties of individual polymers as well as biocompatibility/biodegradability. Together with porosity of scaffold, drug/nutrient supply is required in tissue regeneration and healing. High pressure CO2 has been investigated to plasticize many biopolymers and impregnate drugs in scaffolds. This study explores several compositions of PCL-PMMA electrospun scaffolds for morphological and mechanical properties. These scaffolds are impregnated with hydrophilic (Rhodamine B) and hydrophobic (Fluorescein) dyes using high pressure CO2 and air plasma treatment. Furthermore, release profiles of dyes have been studied from thin films and porous scaffolds to understand several controlling factors for controlled release applications. Results show dye-polymer interactions, CO2 impregnation and stress relaxation of electrospun fibers are key factors in release profile from electrospun fibers. This study is a step forward in developing PCL-PMMA based electrospun scaffolds for drug delivery and tissue engineering. 相似文献
Ultrafine nylon fibers were prepared by electrospinning of nylon-6,66,1010 terpolymer solution in 2,2,2-trifluoroethanol (TFE). The morphology, crystallinity and mechanical properties of the electrospun nylon-6,66,1010 fibers were investigated by scanning electron microscope (SEM), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and tensile test. The effects of electrospun process parameters such as solution concentration, voltage and tip-to-collector distance on the morphology and the average size of the electrospun fibers were also studied. The results show that the spinnable concentration of nylon-6,66,1010/TFE solution is in the range of 6-14 wt%, and higher solution concentration favors the formation of uniform fibers without beads. The diameters of the electrospun fibers increase with increasing the solution concentration and decrease slightly with increasing the voltage and needle tip-to-collector distance. But no obvious morphology changes were found with the increase of the voltage and collection distance. DSC and WAXD results suggest that the electrospun nylon-6,66,1010 membranes have lower crystallinity than those of the corresponding casting films. The electrospun nylon-6,66,1010 membrane obtained from the 14 wt% concentration exhibits the largest tensile strength and elongation at break. 相似文献
Tissue engineering scaffolds should provide a suitable porous structure and proper mechanical strength, which is beneficial for the delivery of growth factor and regulation of cells. In this study, the open‐porous polycaprolactone (PCL)/poly (lactic acid) (PLA) tissue engineering scaffolds with suitable porous scale were fabricated using different ratios of PCL/PLA blends. At the same time, the relationship of foaming process, morphology, and mechanical behavior in the optimized batch microcellular foaming process were studied based on the single‐factor experiment method. The porous structures and mechanical strength of the scaffolds were optimized by adjusting foaming parameters, including the temperature, pressure, and CO2 dissolution time. The results indicated that the foaming parameters influence the cell morphology, further determine the mechanical behavior of PCL/PLA blends. When the PCL content is high, with the increase of temperature and time, the cell diameter and the elastic modulus increased, and the tensile strength and elastic modulus increased with the increase of the average cell size, and decreased as the increase of the cell density. While when the PLA content was high, the cell diameter showed the same trend, and the tensile strength and elastic modulus were higher, and the elongation at break was lower, and tensile strength and elastic modulus decreased with the increase of the average cell size and increased with the increase of cell density. This work successfully fabricated optimized porous PCL/PLA scaffolds with excellent suitable mechanical properties, pore sizes, and high interconnectivity, indicating the effectiveness of modulating the batch foaming process parameters. 相似文献
In this paper, experimental investigation and numerical modelling of the mechanical properties of polyvinylidene fluoride (PVDF) nanofibrous membranes produced by electrospinning are addressed. Membranes with three different diameters are fabricated by adjusting the needle-collector distance during electrospinning. The fiber morphology and the physical properties of the resulting membranes are investigated using Scanning Electron Microscopy (SEM) while their elastic properties are probed using conventional tensile tests. It is found that the membrane with the largest nanofiber diameters are filled with large beads while the contrary is found in the membrane with the smallest nanofiber diameter. Consequently, the membrane with the smallest nanofiber diameter yielded the highest membrane Young's modulus thanks to better fiber packing and higher crystallinity in the nanofibers. Next, the experimental results serve as basis for a pixel-based finite element method (FEM) which is applied directly on the SEM images of the membranes. This technique has the advantage of providing estimations of mechanical properties from the real structure of the membranes. Two parameters are needed for this linear elastic analysis: the elastic modulus of a single fiber and the fiber percentage in the membrane. Results show that the model predictions are in good agreement with experimental data. These results suggest that the pixel-based FEM could be a promising nondestructive alternative to the conventional tensile tests. 相似文献
The regenerated silk fibroin dissolved in formic acid was electrospun into nanofiber mats. Structural characteristics of the
spun as received and methanol and ethanol treated fibers were examined using the Fourier transform infrared (FTIR) spectroscopy
and X-ray diffraction. Mechanical properties and air permeability of the electrospun mats were also studied. IR spectroscopy
and X-ray diffractometry showed random coil conformation and amorphous structure for as-spun fibers while typical FTIR spectra
and X-ray diffractograms of β-sheet crystalline structure were recorded for the methanol and ethanol treated fibers. The mechanical
properties of the mats were found to be dependent on fiber diameter. The mats containing fibers with smaller diameter had
higher tensile strength but lower breaking strain. Methanol and ethanol treatment enhanced tensile strengths of the mats at
the expenses of their breaking strain. Air permeability and pore size of the mats are strongly associated with diameter of
the electrospun fibers. 相似文献
In this work, the investigation of the physical, mechanical, and morphological properties of the rice husk flour/polypropylene composites was performed utilizing various filler loadings and coupling agent. Five levels of filler loading (35, 40, 45, 50, and 55 wt%) were designed. In addition, to help the interaction between fiber and polypropylene matrix, struktol coupling agent was added to the composites. All of tensile strength, Young's modulus, flexural strength, flexural modulus, and impact strength properties of the composites were carried out. Moreover, the 50 wt% filler-loaded composites had optimum tensile strength, flexural strength, and flexural modulus, whereas the 35 wt% of filler loading case was the best regarding Young's modulus, flexural strength, flexural modulus, and impact strength. Furthermore, the scanning electron microscope results demonstrate that as filler loading increases, more voids and fiber pullout occur. 相似文献
Polyvinylidene fluoride (PVDF) is a significant polymer in the formation of nanofiber webs via the electrospinning technique. In this paper, three PVDF-wrinkled fiber webs with different molecular weights (MWs) (180000, 275000, and 530000) were generated via the electrospinning method by using tetrahydrofuran/N,N-dimethylformamide at the solvent ratio of 1:1 as a mixed solvent. The formation mechanism of the wrinkled electrospun PVDF fibers is demonstrated. Furthermore, the relationships between the MW and the surface structure, mechanical properties, crystalline phases, and piezoelectric properties of electrospun PVDF fibers are comprehensively investigated. The results reported that the surface structure, mechanical properties, crystalline phases, and piezoelectric properties of wrinkled electrospun PVDF fibers can be affected intensely by maneuvering the MW. We believe this study can be served as a good reference for the effect of MW on the morphology and properties of electrospun fibers. 相似文献
The objective of this study is to design a novel kind of scaffolds for blood vessel and nerve repairs. Random and aligned nanofibrous scaffolds based on collagen-chitosan-thermoplastic polyurethane (TPU) blends were electrospun to mimic the componential and structural aspects of the native extracellular matrix, while an optimal proportion was found to keep the balance between biocompatibility and mechanical strength. The scaffolds were crosslinked by glutaraldehyde (GTA) vapor to prevent them from being dissolved in the culture medium. Fiber morphology was characterized using scanning electron microscopy (SEM) and atomic-force microscopy (AFM). Fourier transform infrared spectroscopy (FTIR) showed that the three-material system exhibits no significant differences before and after crosslinking, whereas pore size of crosslinked scaffolds decreased drastically. The mechanical properties of the scaffolds were found to be flexible with a high tensile strength. Cell viability studies with endothelial cells and Schwann cells demonstrated that the blended nanofibrous scaffolds formed by electrospinning process had good biocompatibility and aligned fibers could regulate cell morphology by inducing cell orientation. Vascular grafts and nerve conduits were electrospun or sutured based on the nanofibrous scaffolds and the results indicated that collagen-chitosan-TPU blended nanofibrous scaffolds might be a potential candidate for vascular repair and nerve regeneration. 相似文献