The effect of the sampling interface on spatial distributions of barium ions and atoms in an inductively coupled plasma ion source

Planar laser-induced fluorescence was used to examine the effect of the sampling cone on analyte atom and ion distributions in the inductively coupled plasma used as an ion source for elemental mass spectrometry. Comparisons of planar laser-induced fluorescence images in the presence and absence of the sampling interface reveal that the insertion of the sampling cone into the plasma dramatically lowers singly-charged ion densities in the 1–2 mm region immediately upstream from the sampling cone, but increases densities in the region between 2 mm and 10 mm upstream from the sampling cone. Some of the drops in densities near the sampling cone can be attributed to acceleration of the plasma through the pumped sampling orifice. A shift in equilibrium between doubly and singly charged barium ions caused by cooling of the plasma is proposed to account for the increases in densities of Ba⁺ in the upstream region.     

Spatially resolved measurements of ion density behind the skimmer of an inductively coupled plasma mass spectrometer

Ions are extracted from the inductively coupled plasma through a conventional sampler and skimmer and then deposited on an array of graphite targets at the exit of a set of electrostatic ion lenses. The Sc⁺ signal is enhanced by choosing appropriate potentials on the ion lenses. The Sc⁺ signal is suppressed by the presence of concomitant Cs ions at high concentrations. Comparisons of grounded ion lenses and two different ion lens potential settings are made. The signal is enhanced more extensively by the ion lenses when there are no concentrated concomitant ions. This study indicates that matrix effects in inductively coupled plasma mass spectrometry could possibly be alleviated by choosing ion lens potentials such that the ions enter the ion optics with a relatively broad beam cross section, the beam then being focused to a smaller size. A photon stop inside the ion lens stack reduces ion transmission and changes the shape of the beam profile from conical to bimodal.     

Optical measurements of ion density in the second vacuum stage of an inductively coupled plasma mass spectrometer

A portion of the ion beam in the second stage of an inductively coupled plasma mass spectrometer was mapped using laser induced fluorescence (LIF). With LIF relative density measurements are made in real time with minimal interference to the ion beam. We report axial measurements of Ba and Sc ion density from 22 to 45 mm behind the tip of the skimmer cone. Additionally, maps of radial ion density with and without Pb and Mg matrices are given for the same two analyte species. The results reveal that earlier ion deposition experiments dramatically underestimated the extent of the radial spread of the ion beam and the influence of matrix on the ion beam.     

High resolution studies of the origins of polyatomic ions in inductively coupled plasma-mass spectrometry,Part I. Identification methods and effects of neutral gas density assumptions,extraction voltage,and cone material

Common polyatomic ions (ArO⁺, NO⁺, H₂O⁺, H₃O⁺, Ar₂⁺, ArN⁺, OH⁺, ArH⁺, O₂⁺) in inductively coupled plasma-mass spectrometry (ICP-MS) are identified using high mass resolution and studied using kinetic gas temperatures (T_gas) determined from a dissociation reaction approach. Methods for making accurate mass measurements, confirming ion identifications, and correcting for mass bias are discussed. The effects of sampler and skimmer cone composition and extraction voltage on polyatomic ion formation are also explored. Neutral species densities at several locations in the extraction interface are estimated and the corresponding effects of the T_gas value are calculated. The results provide information about the origins of background ions and indicate possible locations for their formation or removal.     

Investigation of polyelectrolytes by total reflection X-ray fluorescence spectrometry

Water soluble polyelectrolyte samples containing mono-, bi- and trivalent metal ions were investigated without any pretreatment. Acid digestion of linear polymers may lead to a product insoluble in water so the digestion has to be avoided. The determination of analytical characteristics and limitations of the total reflection X-ray fluorescence (TXRF) analysis for poly(vinylalcohol-vinylsulfate) copolymers containing the following cations: Cs⁺; Ba²⁺; Cu²⁺ and La³⁺ are presented in this communication. On the basis of our results efficiency of ion-exchange during preparation of polyelectrolytes and stoichiometry of the end-product were determined. TXRF results were compared with data gained by inductively coupled plasma atomic emission spectrometry (ICP-AES) measurements except in the case of Cs⁺, which has poor sensitivity in ICP-AES. Good agreement was found between the results of the two techniques and calculations from titrimetric data. Concentration of Li⁺ and Mg²⁺ in polymer samples was measured only by ICP-AES.     

Statistical mechanics of Ar2+ in an inductively coupled plasma

In the mass spectrum of an argon inductively coupled plasma (ICP), there is a peak due to the presence of the argon dimer ion, Ar₂⁺. Using elementary statistical mechanics, an attempt is made to elucidate the mechanism responsible for this ion's presence in the ICP, The assumption of local thermodynamic equilibrium (LTE) in the ICP leads to three possible mechanisms that could be responsible for the presence of the argon dimer ion, however, the results of the calculations show that only one of the mechanisms agrees with experiment. The experimental measurements of the number density ratio of Ar₂⁺ to Ar⁺, against which the theoretical values are compared, were taken using inductively coupled plasma mass spectrometry (ICP-MS),     

Inductively Coupled Plasma Mass Spectrometry with an Electrically Floating Sampling Interface

In conventional inductively coupled plasma mass spectrometry devices, the sampler and skimmer are grounded. In this work, modest DC voltages (+ 10 to + 50 Vl are applied to either (or both) sampler and skimmer. Alternatively, the skimmer is biased, and the sampler is merely left floating. The latter arrangement improves sensitivity for Co⁺ by sixfold, provides nearly the same molar sensitivity for CO⁺, Rh⁺, and Ho⁺, and extends the upper end of the linear dynamic range to approximately 100 ppm. These changes to the interface do not affect the background perceptibly. The relationship between applied potential and the potential actually measured on the sampler and skimmer is also discussed.     

Temperature and density measurements in a recombining argon plasma with diluent

Spectroscopic and callorimetric measurements of temperature arid number density have been made using a 50-kW radio-frequency inductively coupled plasma (RFICP) torch operated at atmospheric pressure with maximum temperatures and electron densities near 8,1000 K and 2 x 10²¹ m³, respectively These measurements enabled the determination o/ the stale o/ equilibrium and of the corresponding applicability of rarious diagnostic techniques in hoth a recombining argon plasma and a recombining plasma with hydrogen or nitrogen. Results indicate that the Pure argon plasma is well described by u partial equilibrium model in which the free and bound-excited electrons are in mutual equilibrium irespective of possible departures from equilibrium with the ground state. The addition of just tenths of a percent of either atomic Hydrogen or nitrogen, however, disturbs this partial equilibrium hr argon plasmas with electron densities roughly less than 10²¹ m³ such that only diagnostic techniques which are independent o/ partial equilibrium assumptions can be reliably implemented.     

Isotopic fingerprint method: Assessment of the origin of rare earth compounds from the isotope ratios of lead impurities

The isotope ratios ²⁰⁷Pb:²⁰⁶Pb and ²⁰⁸Pb: ²⁰⁶Pb are measured by means of inductively coupled plasma mass spectrometry (ICP-MS) for monazite minerals and commercial rare earth compounds and are evaluated with respect to the initial composition of the minerals and the origin of the samples. The application of the isotopic fingerprint method is demonstrated.Dedicated to Professor Dr. Dieter Klockow on the occasion of his 60th birthday     

Comparing the capability of collision/reaction cell quadrupole and sector field inductively coupled plasma mass spectrometers for interference removal from 90Sr, 137Cs,and 226Ra

Here we report a quantitative comparison of sector field inductively coupled plasma mass spectrometry (ICP-SFMS) and collision/reaction cell inductively coupled plasma quadrupole mass spectrometry (ICP-QMS) for the detection of ⁹⁰Sr, ¹³⁷Cs, and ²²⁶Ra at ultra-trace levels. We observed that the identification and quantification of radioisotopes by ICP-MS were hampered by spectral (both isobaric and polyatomic ions) and non-spectral (matrix effect) interferences. ICP-QMS has been used to eliminate the isobaric ⁹⁰Sr/⁹⁰Zr interference through the addition of O₂ into the collision cell as a reactant gas. Zr⁺ ions were subsequently converted into ZrO⁺, whereas Sr⁺ ions were not reactive. In addition, the isobaric interference of ¹³⁷Ba on ¹³⁷Cs was eliminated by the addition of N₂O gas in the cell, which led to the formation of BaO⁺ and BaOH⁺ products, whereas Cs⁺ remained unreactive. Furthermore, He and H₂ were used in the collision/reaction cell to eliminate polyatomic ions formed at m/z 226. A comparison of the results obtained by ICP-SFMS after a chemical separation of Sr from Zr and Cs from Ba was performed. Finally, to validate the developed analytical procedures, measurements of the same samples were performed by γ-ray spectroscopy.     

High resolution imaging of barium ions and atoms near the sampling cone of an inductively coupled plasma mass spectrometer

Planar laser-induced fluorescence was used to map density distributions of ground state barium atoms, ground state barium ions, and excited-state barium ions in the region between the load coil and the sampling cone of an inductively coupled plasma mass spectrometer. The effects of power, nebulizer gas flow rate, and the addition of lithium to the sample on the distributions were studied. The maps reveal that the radial distributions of atomic species across the diameter of the plasma are compressed as the plasma is drawn into the sampling orifice, and that as a result of that compression, the distribution of ions across the 1-mm diameter of the sampling orifice is non-uniform. The distribution changes as conditions in the plasma change. The skimmer cone that separates the first and second stages of the differentially-pumped vacuum interface transmits ions exclusively from the center of the distribution that exists at the sampling cone. As a result, the overall efficiency with which ions are transmitted through the vacuum interface varies as conditions in the plasma change.     

Quantification of water and plasma diagnosis for electrothermal vaporization–inductively coupled plasma–mass spectrometry: the use of argon and argide polyatomics as probing species

The water content of the carrier flow originating from an electrothermal vaporization unit (ETV) attached to an inductively coupled plasma mass spectrometer was monitored by following the argon hydride ion (ArH⁺) at m/z=37. The goal was to measure the water expelled by the ETV at sample vaporization and evaluate the influence of this parameter on the ion-generation efficiency. Linear responses from the argon hydride were obtained when the water loading in the plasma injector flow was increased from 0 to 3.3 mg/min. Other argides and water-derived species (Ar⁺, Ar⁺₂ and O⁺₂) were also monitored simultaneously and the effects from operating parameters have been calculated for each species. The magnitude of these effects can eventually be used as diagnosis tools. It was also found that signals for zinc, copper, lead, antimony and arsenic were greatly influenced by slight variations in water loading at low water levels. These signal fluctuations are greatly attenuated and transients' shapes restored by convoluting each element transient with the ArH⁺ or Ar⁺₂ curves that were recorded simultaneously. Envisioned applications that would benefit from a water-enhanced signal include spray electrothermal vaporization, direct sample insertion and laser ablation for inductively coupled plasma–mass spectrometry. The argon dimer Ar⁺₂ seems more appropriate for making the correction since it provides a direct insight on the plasma temperature and provides a robust signal.     

Determination of trace elements in suspensions and filtrates of drinking and surface water by wavelength-dispersive X-ray fluorescence spectrometry

An X-ray fluorescence method (XRF) is presented that allowed low detection limits (at the 0.1–23 ng mL⁻¹ level) to be obtained for Cr, Mn, Fe, Ni, Zn, Sr, Pb, Bi and Br in water. The samples were prepared using a thin layer method. Trace elements were determined via the calibration curve and standard addition. Absorption effects and inhomogenities in prepared samples were checked for using the emission–transmission method and internal standards, respectively. The results from the XRF method were compared with the results from the inductively coupled plasma atomic emission spectrometry method.      

Inductively coupled plasma mass spectrometry with a quadrupole mass filter operated in the third stability region

An inductively coupled plasma mass spectrometer system is described in which the quadrupole mass filter is operated in the third stability region with Mathieu parameters (a, q)=(3, 3). Operation at the upper tip of this region is found to give generally better sensitivity and resolution than operation at the lower tip. A limiting resolution at half height of 4000 at m/z 59 is possible with operation at the upper tip. This resolution is insufficient to separate atomic ions from molecular ions of the same nominal mass except in favorable cases. However, operation at moderate resolution (R _1/2=500 to 1000) is found to give very high abundance sensitivity (>10⁷). The results suggest that the third stability region may be advantageous for specialized applications of inductively coupled plasma mass spectrometry.     

Evaluation of a Collision-Reaction Interface (CRI) for Carbon Effect Correction on Chromium Determination in Environmental Samples by ICP-MS

Spectral interferences in inductively coupled plasma quadrupole mass spectrometry (ICP-MS) may affect several trace element analyses. In this work, the performance of a collision-reaction interface (CRI) for correction of spectral interferences on chromium determination at m/z 52 affected by ⁴⁰Ar¹²C⁺ in a rich-carbon medium was evaluated. Hydrogen or He gases were introduced through sampler or skimmer cones of the CRI for promoting collisions and reactions. Background equivalent concentrations (BEC) and signal-background ratios (SBR) were the chosen parameters for evaluating CRI performance. It was observed that the introduction of both gases through the sampler cone was not effective considering the maximum gas flow rate evaluated at 140 mL min^?1. The best condition to reduce polyatomic interferences caused by carbon containing species was obtained while introducing 60 mL min^?1 of H₂ through the skimmer cone. The trueness of the developed procedure was checked by ⁵²Cr⁺ determination in certified reference materials. Sequential extractions in acetic acid and ammonium acetate (carbon sources) media, according to the Bureau Communautaire de Référence (BCR) of the Commission of the European Communities, was employed for BCR 701 (Lake Sediment) and microwave-assisted digestion was applied for Sewage Sludge from Industrial Origin (BCR 146 R). The feasibility of the CRI to overcome spectral interferences caused by molecular ions containing carbon on ⁵²Cr⁺ determined by ICP-MS was demonstrated.     

Detoxification of mercury species—an in vitro study with antidotes in human whole blood

To investigate the effects of mercury species intoxication and to test the efficiency of different commonly applied antidotes, human whole blood and plasma surrogate samples were spiked with inorganic mercury (Hg²⁺) and methylmercury (MeHg⁺, CH₃Hg⁺) prior to treatment with the antidotes 2,3-dimercaptopropan-1-ol (British Anti Lewisite), 2,3-dimercaptosuccinic acid (DMSA), and N-acetylcysteine (NAC). For mercury speciation analysis in these samples, liquid chromatography was coupled to either inductively coupled plasma mass spectrometry (ICP-MS) or electrospray ionisation time-of-flight mass spectrometry (ESI-TOF-MS). Adduct formation between mercury species and physiological thiols (cysteine and glutathione) was observed as well as the release of glutathione under treatment with the antidotes DMSA and NAC.     

Summary of ISO/TC 201 Standard: XIX ISO 17331:2004—Surface chemical analysis—Chemical methods for the collection of elements from the surface of silicon‐wafer working reference materials and their determination by total‐reflection x‐ray fluorescence (TXRF) spectroscopy

This international standard specifies chemical methods for the collection of iron and/or nickel from the surface of silicon‐wafer working reference materials by the vapour‐phase decomposition method or the direct acid droplet decomposition method. The determination of the elements collected may be carried out by total‐reflection x‐ray fluorescence spectroscopy, as well as by graphite‐furnace atomic absorption spectroscopy or inductively coupled plasma mass spectroscopy. This international standard applies to iron and/or nickel atomic surface densities from 6 × 10⁹ to 5 × 10¹¹ atoms cm^?2. Copyright © 2005 John Wiley & Sons, Ltd.     

Inductively coupled plasma mass spectrometry with an enlarged sampling orifice and offset ion lens. II. Polyatomic Ion interferences and matrix effects

A new inductively coupled plasma mass spectrometer with an enlarged sampling orifice (1.31-mm dia.) and an offset ion lens yields very low levels of many troublesome polyatomic ions such as ArO⁺, ArN⁺, Ar₂ ⁺, ClO⁺, and ArCl⁺. The signals from refractory metal oxide ions are ≈ 1% of the corresponding metal ion signals, which is typical of most ICP-MS devices. Grounding the first electrode of the ion lens greatly reduces the severity of matrix effects to <- 20% loss in signal for Co⁺, Y⁺, or Cs⁺ in the presence of 10 mM Sr, Tm, or Pb. This latter lens setting causes only a modest loss (30%) in sensitivity for analyte elements compared to the best sensitivity obtainable by biasing the first lens. Alternatively, matrix effects can also be mitigated by readjusting the voltage applied to the first lens with the matrix present.     

Near‐field laser ablation inductively coupled plasma mass spectrometry: a novel elemental analytical technique at the nanometer scale

An analytical technique utilizing a near‐field effect (to enhance the incident light energy on the thin tip of an Ag needle) in a laser ablation inductively coupled plasma mass spectrometry (NF‐LA‐ICP‐MS) procedure was developed. To produce the thin needles with a tip diameter in the hundreds of nm range a robust needle etching procedure was established. The ‘sample‐to‐tip’ distance was controlled via the measurement of a tunnel current between the needle and sample surface. The NF‐LA‐ICP‐MS technique thus developed was applied for the analysis of copper isotopic standard reference material NIST SRM 976 and tungsten‐molybdenum alloy NIST SRM 480 in the nm resolution range. The observed craters ranged from 200 nm to about 2 µm in diameter and were dependent on the needle used as well as on the ‘sample‐to‐tip’ distance. The mass spectrometric measurements of ⁶³Cu⁺ ion intensity on NIST SRM 976 showed that using near‐field enhancement in laser ablation allowed a roughly 6‐fold increase in the ion intensity of the analyte when the needle was about 100 nm (and below) from the surface, in contrast to when it was far away (e.g. 10 µm) from the sample. The relative standard deviation (RSD) of the ⁶⁵Cu⁺/⁶³Cu⁺ isotopic ratio measurements by NF‐LA‐ICP‐MS was 3.9% (n = 9). The detection efficiencies obtained for the compared LA‐ICP‐MS and NF‐LA‐ICP‐MS methods were found to be 4.6 * 10^?3 counts per second (cps)/ablated atom and 2.7 * 10^?5 cps/ablated atom, respectively. Copyright © 2008 John Wiley & Sons, Ltd.     

Kinetic study of low-pressure H2 multipole discharge

This paper is devoted to the study of kinetic equilibrium among electrons, H₂ molecules, H atoms, and positive H⁺, H ₂ ⁺ , and H ₃ ⁺ ions in a multipole discharge working under low-pressure (1- to 15-m Torr) and moderated current conditions. In such a discharge used either as a H⁺ or a H^– ion source or for plasma-surface interactions, the dependence of the densities of these species versus experimental parameters is of a great interest. In the present situation, the electron energy distribution function (e.e.d.f.) is largely nonmaxwellian. The kinetic model that determines the densities of the plasma species is self-consistently coupled to the e.e.d.f. calculated through the use of the Boltzmann equation. The influence of the main processes, volume ones, and those involving plasma walls is emphasized. An attempt is made to use the profiles of Balmer lines obtained experimentally in order to determine absolute concentrations of H atoms and H ₂ ⁺ ions. Results derived from the experiment are compared to results of the model. Such an analysis of Balmer line shapes appears to be an interesting way to determine, by anin situ nonintrusive method, the absolute concentration of H atoms.