Homogeneous interface-type resistance switching in Au/La_0.67Ca_0.33MnO₃/SrTiO₃/F:SnO₂ heterojunction memories

La0.67Ca0.33MnO3 thin films are fabricated on fluorine-doped tin oxide conducting glass substrates by a pulsed laser deposition technique with SrTiO3 used as a buffer layer. The current-voltage characteristics of the heterojunctions exhibit an asymmetric and resistance switching behaviour. A homogeneous interface-type conduction mechanism is also reported using impedance spectroscopy. The spatial homogeneity of the charge carrier distribution leads to field- induced potential-barrier change at the Au-La0.67Ca0.33MnO3 interface and a concomitant resistance switching effect. The ratio of the high resistance state to the low resistance state is found to be as high as 1.3 × 10 4 % by simulating the AC electric field. This colossal resistance switching effect will greatly improve the signal-to-noise ratio in nonvolatile memory applications.     

Interface-related switching behaviors of amorphous Pr0.67Sr0.33MnO3-based memory cells

The resistive switching properties in amorphous Pr0.67Sr0.33MnO3 films deposited by pulsed laser deposition are investigated.Reproducible and bipolar counter-8-shape and 8-shape switching behaviours of Au/Pr0.67Sr0.33MnO3 /F：SnO2 junctions are obtained at room temperature.Dramatically,the coexistence of two switching polarities could be reversibly adjusted by an applied voltage range.The results allocated those two switching types to areas of different defect densities beneath the same electrode.The migration of oxygen vacancies and the trapping effect of electrons under an applied electric field play an important role.An interface-effect-related resistance switching is proposed in an amorphous Pr0.67Sr0.33MnO3-based memory cell.     

(Pr,Nd)_(2/3)Sr_(1/3)MnO_3体系中的低温比热反常现象

主要研究了(Pr1-yNdy)2/3Sr1/3MnO3体系多晶样品在低温下的比热反常现象.Pr2/3Sr1/3MnO3在低温下没有比热反常现象,但随着Nd替代Pr,比热反常开始出现,峰值逐渐增加,峰值出现温度逐渐减小;在磁场的作用下,峰值减小,峰值出现温度逐渐增加;经分析,该低温比热反常现象与Schottky效应相关.     

The influence of interfacial barrier engineering on the resistance switching of In₂O₃:SnO₂/TiO₂/In₂O₃:SnO₂ device

The I–V characteristics of In2O3:SnO2/TiO2/In2O3:SnO2 junctions with different interfacial barriers are inves- tigated by comparing experiments. A two-step resistance switching process is found for samples with two interfacial barriers produced by specific thermal treatment on the interfaces. The nonsynchronous occurrence of conducting filament formation through the oxide bulk and the reduction in the interfacial barrier due to the migration of oxygen vacancies under the electric field is supposed to explain the two-step resistive switching process. The unique switching properties of the device, based on interfacial barrier engineering, could be exploited for novel applications in nonvolatile memory devices.     

Charge ordering modulations in a Bi_0.4Ca_0.6MnO₃ film with a thickness of 110 nm

The low temperature sample stage in a transmission electron microscope is used to investigate the charge ordering behaviours in a Bi 0.4 Ca 0.6 MnO 3 film with a thickness of 110 nm at 103 K.Six different types of superlattice structures are observed using the selected-area electron diffraction(SAED) technique,while three of them match well with the modulation stripes in high-resolution transmission electron microscopy(HRTEM) images.It is found that the modulation periodicity and direction are completely different in the region close to the Bi 0.4 Ca 0.6 MnO 3 /SrTiO 3 interface from those in the region a little further from the Bi 0.4 Ca 0.6 MnO 3 /SrTiO 3 interface,and the possible reasons for this are discussed.Based on the experimental results,structural models are proposed for these localized modulated structures.     

Tunable Ba_0.5 Sr_0.5 TiO₃ film bulk acoustic resonators using SiO₂ /Mo Bragg reflectors

Tunable and switchable Ba 0.5 Sr 0.5 TiO 3 film bulk acoustic resonators(FBARs) based on SiO 2 /Mo Bragg reflectors are explored,which can withstand high temperature for the deposition of Ba x Sr 1 x TiO 3(BST) films at 800 C.The dc bias-dependent resonance may be attributed to the piezoelectricity of the BST film induced by an electrostrictive effect.The series resonant frequency is strongly dc bias-dependent and shifts downwards with dc bias increasing,while the parallel resonant frequency is only weakly dc bias-dependent and slightly shifts upwards at low dc bias(< 45 V) while downwards at higher dc bias.The calculated relative tunability of shifts at series resonance frequency is around 2.3% and the electromechanical coupling coefficient is up to approximately 8.09% at 60-V dc bias,which can be comparable to AlN FBARs.This suggests that a high-quality tunable BST FBAR device can be achieved through the use of molybdenum(Mo) as the high acoustic impedance layer in a Bragg reflector,which not only provides excellent acoustic isolation from the substrate,but also improves the crystallinity of BST films withstanding higher deposition temperature.     

High temperature thermoelectric properties of highly c-axis oriented Bi₂Sr₂Co₂O_y thin films fabricated by pulsed laser deposition

High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co2Oy thin films prepared by pulsed laser deposition on LaAlO3(001).Both the electric resistivity ρ and the seebeck coefficient S of the film exhibit an increasing trend with the temperature from 300 K-1000 K and reach up to 4.8 m·Ω· cm and 202 μV/K at 980 K,resulting in a power factor of 0.85 mW/mK which are comparable to those of the single crystalline samples.A small polaron hopping conduction can be responsible for the conduction mechanism of the film at high temperature.The results demonstrate that the Bi2Sr2Co2Oy thin film has potential application in high temperature thin film thermoelectric devices.     

Improved multiferroic properties of La-doped 0.6BiFeO₃-0.4SrTiO₃ solid solution ceramics

The 0.6(Bi1-xLax)FeO 3-0.4SrTiO 3(x = 0,0.1) multiferroic ceramics are prepared by a modified Pechini method to study the effect of substitution of SrTiO3 and La in BiFeO3.The X-ray diffraction patterns confirm the single phase characteristics of all the compositions each with a rhombohedral structure.The magnetic properties of the ceramics are significantly improved by a solid solution with SrTiO3 and substitution of La.The values of the dielectric constant ε r and loss tangent tan δ of all the samples decrease with increasing frequency and become constant at room temperature.The La-doped 0.6BiFeO3-0.4SrTiO3 ceramics exhibit improved dielectric and ferroelectric properties,with higher dielectric constant enhanced remnant polarization(Pr) and lower leakage current at room temperature.Compared with a anti-ferromagnetic BiFeO3 compound,the 0.6(Bi0.9La0.1)FeO3-0.4SrTiO3 sample shows the optimal ferromagnetism with remnant magnetization M r ～ 0.135 emμ/g and ferroelectricity with Pr ～ 5.94 μC/cm 2 at room temperature.     

Homogeneous interface-type resistance switching in Au/La0.67Ca0.33MnO3/SrTiO3/F:SnO2 heterojunction memories

La0.67Ca0.33MnO3 thin films are fabricated on fluorine-doped tin oxide conducting glass substrates by a pulsed laser deposition technique with SrTiO3 used as a buffer layer. The current-voltage characteristics of the heterojunetions exhibit an asymmetric and resistance switching behaviour. A homogeneous interface-type conduction mechanism is also reported using impedance spectroscopy. The spatial homogeneity of the charge carrier distribution leads to field- induced potential-barrier change at the Au-La0.67Ca0.33MnO3 interface and a concomitant resistance switching effect. The ratio of the high resistance state to the low resistance state is found to be as high as 1.3 x 10^4% by simulating the AC electric field. This colossal resistance switching effect will greatly improve the signal-to-noise ratio in nonvolatile memory applications.     

Microphase separation in Pr0.67Ca0.33MnO3 by small-angle neutron scattering

We have evidenced by small-angle neutron scattering at low temperature the coexistence of ferromagnetism (F) and antiferromagnetism (AF) in Pr0.67Ca0.33MnO3. The results are compared to those obtained in Pr0.80Ca0.20MnO3 and Pr0.63Ca0.37MnO3, which are F and AF, respectively. Quantitative analysis shows that the small-angle scattering is not due to a mesoscopic mixing but to a nanoscopic electronic and magnetic "red cabbage" structure, in which the ferromagnetic phase exists in the form of thin layers in the AF matrix (stripes or 2D "sheets").     

Amorphous-crystalline dual-layer structures resulting from metastable liquid phase separation in(Fe₅₀Co₂₅B₁₅Si₁₀)₈₀Cu₂₀ melt-spun ribbons

(Fe50Co25B15Si10)80Cu20 ribbons are prepared by using the single-roller melt-spinning method.A dual-layer structure consisting of a(Fe,Co)-rich amorphous phase and a Cu-rich crystalline phase forms due to metastable liquid phase separation before solidification.The magnetic hysteresis loops of the as-quenched and annealed samples are measured at room temperature.It is indicated that the coercivity of the ribbon is almost zero in the as-quenched state.The crystallization leads to the increase of coercivity and decrease of saturation magnetization.     

Influence of the Jahn-Teller distortion on magnetic ordering in TbMn_1-xFe_xO₃

The Jahn-Teller distortion plays an important role in determining the exchange interaction in rare-earth manganites.In this work we study the influence of the Jahn-Teller distortion on the magnetic structures of TbMn1-xFexO3(x = 0,0.02,0.05,0.10,and 0.20) single crystals in the basal MnO2 plane.The decrease in the quadruple splitting with the increasing Fe doping indicates the reduction of the Jahn-Teller distortion,which makes the nearest neighboring(NN) FM interaction dominant over the next nearest neighbor(NNN) AFM interaction.This alteration is favorable for the development of A-type AFM ordering instead of the spiral magnetic ordering,which collapses when x ≥ 0.05.The analysis of dielectric data indicates that the ferroelectricity is arising from the peculiar spiral magnetic ordering.     

10BaF₂:NaF,Na₃AlF₆/TiO₂ composite as a novel visible-light-driven photocatalyst based on upconversion emission

A rare-earth free upconversion luminescent material, 10BaF 2 :NaF, Na 3 AlF 6 , is synthesized by a hydrothermal method. The study of fluorescent spectrum indicates that it can convert visible light (550 nm–610 nm) into ultraviolet light (290 nm–350 nm), and two emission peaks at 304 nm and 324 nm are observed under the excitation of 583 nm at room temperature. Subsequently, 10BaF 2 :NaF, Na 3 AlF 6 /TiO 2 composite photocatalyst is prepared and its catalytic activity is evaluated by the photocatalytic reduction of CO 2 under visible light irradiation (λ > 515 nm). The results show that 10BaF 2 :NaF, Na 3 AlF 6 /TiO 2 is a more effective photocatalyst for CO 2 reduction than pure TiO 2 , their corresponding methanol yields are 179 and 0 μmol/g-cat under the same conditions. Additionally, the mechanism of photocatalytic reduction of CO 2 on 10BaF 2 :NaF, Na 3 AlF 6 /TiO 2 is proposed.     

Role of Excess Manganese in Formation of the Structure and Transport Properties of Manganite (Nd0.67Sr0.33)1–xMn1 + xO3 (x = 0, 0.2) Sintered at 1273–1473 K

Physics of the Solid State - The Nd0.67Sr0.33MnO3 manganite is a material promising for application as a cathode for medium-temperature solid oxide fuel elements. A high electrical conductivity of...     

The interplay between the lattice and magnetism in La(Fe_11.4Al_1.6)C_0.02 studied by powder neutron diffraction

The crystallographic structure and magnetic properties of La(Fe 11.4 Al 1.6 )C 0.02 are studied by magnetic measure- ment and powder neutron diffraction with temperature and applied magnetic field. Rietveld refinement shows that La(Fe 11.4 Al 1.6 )C 0.02 crystallizes into the cubic NaZn 13 -type with two different Fe sites: Fe I (8b) and Fe II (96i), and that Al atoms preferentially occupy the Fe II site. A ferromagnetic state can be induced at a medial temperature of 39 K–139 K by an external magnetic field of 0.7 T, and a large lattice is correspondingly found at 100 K and 0.7 T. In all other conditions, La(Fe 11.4 Al 1.6 )C 0.02 has no net magnetization in the paramagnetic (T > T N = 182 K) or antifer- romagnetic states, and thus keeps its small lattice. Analysis of the Fe–Fe bond length indicates that the ferromagnetic state prefers longer Fe–Fe distances.     

Structure and magnetoresistance of La<Subscript>0.67</Subscript>Ca<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript> films grown coherently on (001)NdGaO<Subscript>3</Subscript>

40-to 120-nm-thick (001)La_0.67Ca_0.33MnO₃ films grown through laser evaporation on (001)NdGaO₃ were studied. The lattice parameters of the La_0.67Ca_0.33MnO₃ films measured in the substrate plane (a_∥=3.851 Å) and along the normal to its surface (a_⊥=3.850 Å) practically coincided with that of the pseudocubic neodymium gallate. The unit-cell volume of the La_0.67Ca_0.33MnO₃ film was slightly smaller than that of stoichiometric bulk samples. The position of the maximum in the temperature dependence of electrical resistivity did not depend on the thickness of the La_0.67Ca_0.33MnO₃ film. The negative magnetoresistance (MR≈?0.25, H=0.4 T) of La_0.67Ca_0.33MnO₃ films reached a maximum at 239–244 K.     

Dynamic Kerr effect and the spectral weight transfer of the manganites

Pump-probe Kerr spectroscopy uncovers surface magnetic dynamics in Pr0.67Ca0.33MnO3 that are undetected by established methods based on optical spectral weight transfer. The connection between spin and charge dynamics in the colossally magnetoresistive manganites may thus be weaker than previously thought. Important differences from conventional ferromagnetic metals manifest as long-lived, magneto-optical coupling transients, which may be generic to all manganites.     

Diode-pumped laser and self-frequency-doubling properties of a Nd³⁺:Na₃La₉O₃(BO₃)₈ crystal

We report efficient, diode-pumped, self-frequency doubling (SFD) in the newly developed laser crystal Nd³⁺:Na₃La₉O₃(BO₃)₈ (Nd:NLBO). More than 730?mW of fundamental output power at 1072?nm was achieved with a slope efficiency of 16.2%. With incident pump power of 8?W, 29?mW of green cw laser emission at 536?nm was observed with proper phase matching. This initial performance and the good optical properties of the crystalline host are encouraging for the development of a high power diode-pumped SFD visible light laser source.     

Response of the electrical resistivity and magnetoresistance of La<Subscript>0.67</Subscript>Ca<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript> epitaxial films to biaxial compressive mechanical (001) or (110) strains

The behavior of the electrical resistivity and magnetoresistance of 40-to 120-nm-thick La_0.67Ca_0.33MnO₃ films grown on differently oriented lanthanum aluminate substrates was studied. The cell volume in thin (40 nm) La_0.67Ca_0.33MnO₃ films grown coherently on (001)LaAlO₃ was found to be substantially smaller. Mechanical stress relaxation in biaxially strained La_0.67Ca_0.33MnO₃ films is accompanied by an increase in the cell volume. The temperatures at which the electrical resistivity and magnetoresistance in biaxially strained La_0.67Ca_0.33MnO₃ films were maximum can differ by 60–70 K from those observed in bulk single crystals.     

Modulation of ultrafast laser-induced magnetization precession in BiFeO<Subscript>3</Subscript>-coated La<Subscript>0.67</Subscript>Sr<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript> thin films

The ultrafast laser-excited magnetization dynamics of ferromagnetic (FM) La_0.67Sr_0.33MnO₃ (LSMO) thin films with BiFeO₃ (BFO) coating layers grown by laser molecular beam epitaxy are investigated using the optical pump-probe technique. Uniform magnetization precessions are observed in the films under an applied external magnetic field by measuring the time-resolved magneto-optical Kerr effect. The magnetization precession frequencies of the LSMO thin films with the BFO coating layers are lower than those of uncoated LSMO films, which is attributed to the suppression of the anisotropy field induced by the exchange interaction at the interface between the antiferromagnetic order of BFO and the FM order of LSMO.