Effect of substrate and annealing on the structural and optical properties of ZnO:Al films

ZnO:Al thin films with c-axis preferred orientation were deposited on glass and Si substrates using RF magnetron sputtering technique. The effect of substrate on the structural and optical properties of ZnO:Al films were investigated. The results showed a strong blue peak from glass-substrate ZnO:Al film whose intensity became weak when deposited on Si substrate. However, the full width at half maxima (FWHM) of the Si-substrate ZnO:Al (0 0 2) peaks decreased evidently and the grain size increased. Finally, we discussed the influence of annealing temperature on the structural and optical properties of Si-substrate ZnO:Al films. After annealing, the crystal quality of Si-substrate ZnO:Al thin films was markedly improved and the intensity of blue peak (∼445 nm) increased noticeably. This observation may indicate that the visible emission properties of the ZnO:Al films are dependent more on the film crystallinity than on the film stoichiometry.     

基底材料对磁控共溅射Al-Cu-Fe薄膜特性的影响

 采用磁控共溅射工艺来制备Al-Cu-Fe薄膜,选用抛光状态的纯Al、纯Cu和不同粗糙度的不锈钢基作为基底材料。通过原子力显微镜分析薄膜的表面形貌,利用扫描电镜能谱仪分析薄膜的元素含量;通过MTS纳米力学综合测试系统分析薄膜的结合强度和摩擦因数。分析结果表明：不锈钢作为基底材料的薄膜与基体的结合强度最大,其次为纯铝和纯铜。纯铜基底薄膜的摩擦因数最大,达到0.17,其余两种薄膜的摩擦因数均不大于0.03。而薄膜表面形貌与基底材料的原始形貌有直接的联系,基底原始粗糙度越小,薄膜的表面组织也越细;基底原始粗糙度越大,薄膜表面形成的晶粒的团聚越明显。     

Ge薄膜特性及其在光子计数成像系统中的应用

利用电子束真空蒸镀方法制作了Ge薄膜,用作感应读出方式光子计数成像系统的电荷感应层,研究了石英玻璃衬底和陶瓷衬底上Ge薄膜的结构特征、表面形态以及各种工艺参数对薄膜电阻的影响.X射线衍射(XRD)测试表明,两种衬底上沉积的Ge薄膜均为立方相非晶态.场发射扫描电子显微镜(FESEM)图像表明石英玻璃衬底上的薄膜致密平整,陶瓷衬底上的薄膜比较粗糙,厚度较薄时,陶瓷晶界处薄膜不连续导致电阻较大.通过改变沉积速率、薄膜厚度及采用退火的方法可以控制薄膜电阻.对比了采用不同阻值电荷感应层时系统的性能,发现阻值对探测器的分辨率影响小,对计数率影响较大.     

Optical and electrical properties of aluminum-doped ZnO thin films grown by pulsed laser deposition

Transparent aluminum-doped zinc oxide (AZO) thin films were deposited on quartz glass substrates by pulsed laser deposition (PLD) from ablating Zn-Al metallic targets. The structural, electrical and optical properties of these films were characterized as a function of Al concentration (0-8 wt.%) in the target. Films were deposited at a low substrate temperature of 150 °C under 11 Pa of oxygen pressure. It was observed that 2 wt.% of Al in the target (or 1.37 wt.% of Al doped in the AZO film) is the optimum concentration to achieve the minimum film resistivity and strong ultraviolet emission. The presence of Al in the ZnO film changes the carrier concentration and the intrinsic defects.     

Atomistic study of deposition process of Al thin film on Cu substrate

In this paper we report molecular dynamics based atomistic simulations of deposition process of Al atoms onto Cu substrate and following nanoindentation process on that nanostructured material. Effects of incident energy on the morphology of deposited thin film and mechanical property of this nanostructured material are emphasized. The results reveal that the morphology of growing film is layer-by-layer-like at incident energy of 0.1-10 eV. The epitaxy mode of film growth is observed at incident energy below 1 eV, but film-mixing mode commences when incident energy increase to 10 eV accompanying with increased disorder of film structure, which improves quality of deposited thin film. Following indentation studies indicate deposited thin films pose lower stiffness than single crystal Al due to considerable amount of defects existed in them, but Cu substrate is strengthened by the interface generated from lattice mismatch between deposited Al thin film and Cu substrate.     

Effects of aluminum doping and substrate temperature on zinc oxide thin films grown by pulsed laser deposition

Aluminum-doped zinc oxide (AZO) thin films have been deposited on amorphous fused silica substrates by pulsed laser ablation of a Zn:Al metallic targets. We varied the film growth condition such as the substrate temperature and Al concentrations. The films were deposited at substrate temperatures ranging from 20 to 600°C with oxygen partial pressure of 1 torr. The characteristics of the deposited films were examined by analyzing their photoluminescence (PL), X-ray diffraction (XRD), and UV–visible spectra. It is observed that the optical bandgap energy of the deposited films increased with the increase of Al concentration and substrate temperature. Besides, the PL peak energy shifted to blue and the Stokes shift became larger as the Al content increased.     

Electro-optical characteristics and field-emission properties of reactive DC-sputtered p-CuAlO2+x thin films

P-type transparent-conducting CuAlO_2+x thin films were deposited on silicon and glass substrates by reactive direct current sputtering of a prefabricated metal powder target having 1:1 atomic ratio of Cu and Al in oxygen-diluted argon atmosphere. XRD spectrum confirmed the proper phase formation of the material. UV-Vis-NIR spectrophotometric measurements showed high transparency of the films in the visible region with direct and indirect band gap values around 3.90 and 1.89 eV, respectively. The room temperature conductivity of the film was of the order of 0.22 S cm⁻¹ and the activation energy was 0.25 eV. Seebeck coefficient at room temperature showed a value of +115 μV/K confirming the p-type nature of the film. Room temperature Hall effect measurement also indicated positive value of Hall coefficient with a carrier concentration 4.4×10¹⁷ cm⁻³. We have also observed the low macroscopic field emission, from the wide band gap p-CuAlO_2+x thin film deposited on glass substrate. The emission properties have been studied for different anode-sample spacing. The threshold field was found to be as low as around 0.5–1.1 V/μm. This low threshold is attributed primarily to the internal nanostructure of the thin film, which causes considerable geometrical field enhancement inside the film as well as at the film/vacuum interface.     

Yield strengths and stress induced crackles in copper films：effects of substrate and passivated layer

Yield strengths in unpassivated and 530 nm TiN passivated Cu films deposited on Ti, high-speed steel and Ni substrates have been measured by x-ray diffraction (XRD) in combination with the four-point bending method. The results show that, although the texture and average grain size, investigated by XRD and transmission electron microscopy respectively, do not vary with different substrate, the yield strength of the Cu film increases obviously when a thin passivated layer is present and varies slightly with substrates. Many crackles appear in the passivated Cu film on Ti substrate but do not appear in other samples. The experimental results have been explained satisfactorily with an expression for the yield strength of thin films given previously.     

Critical role of laser wavelength on carbon films grown by PLD of graphite

The structure of thin films deposited by pulsed laser ablation (PLD) is strongly dependent on experimental conditions, like laser wavelength and fluence, substrate temperature and pressure. Depending on these parameters we obtained various kinds of carbon materials varying from dense, mainly tetrahedral amorphous carbon (ta-C), to less compact vertically oriented graphene nano-particles. Thin carbon films were grown by PLD on n-Si 〈100〉 substrates, at temperatures ranging from RT to 800°C, from a rotating graphite target operating in vacuum. The laser ablation of the graphite target was performed by a UV pulsed ArF excimer laser (λ=193 nm) and a pulsed Nd:YAG laser, operating in the near IR (λ=1064 nm). The film structure and texturing, characterised by X-ray diffraction analysis, performed at grazing incidence (GI-XRD), and the film density, evaluated by X-ray reflectivity measurements, are strongly affected both by laser wavelength and fluence and by substrate temperature. Micro-Raman and GI-XRD analysis established the progressive formation of aromatic clusters and cluster condensation into vertically oriented nano-sized graphene structures as a direct function of increasing laser wavelength and deposition temperature. The film density, negatively affected by substrate temperature and laser wavelength and fluence, in turn, results in a porous bulk configuration and a high macroscopic surface roughness as shown by SEM characterisation. These structural property modifications induce a relevant variation also on the emission properties of carbon nano-structures, as evidenced by field emission measurements. This work is dedicated to our friend Giorgio who passed away 20th August.     

不同基底的GaN纳米薄膜制备及其场发射增强研究

采用脉冲激光沉积 (PLD) 方法在Si及SiC基底上制备了相同厚度的GaN纳米薄膜并对其进行了微结构表征及场发射性能测试分析. 结果表明: 基底对于GaN薄膜微结构及场发射性能具有显著的影响. 在SiC基底上所制备的GaN纳米薄膜相对于Si基底上的GaN纳米薄膜, 其场发射性能得到显著提升, 其场发射电流可以数量级增大. 场发射显著增强应源于纳米晶微结构及取向极化诱导增强效应. 本研究结果表明, 要获得优异性能场发射薄膜, 合适基底及薄膜晶体微结构需要重点考虑. 关键词： 基底 GaN 纳米薄膜 场发射     

Microstructural, optical and electrical studies on sol gel derived ZnO and ZnO:Al films

ZnO and ZnO:Al films were deposited onto glass substrates by the sol gel method using spin coating technique. The effects of aluminum dopant on the crystalline structure and orientation of the ZnO films have been investigated by X-ray diffraction (XRD) study. Surface morphology of the films has also been analyzed by a field emission scanning electron microscope (FESEM) and atomic force microscope (AFM). The average optical transmittance values of all the films is over >83% in the visible region. The optical band gap and Urbach energy values of these films were determined. The absorption edge shifted to the lower energy depending on the Al doping level. The shift of absorption edge is associated with shrinkage effect. The electrical conductivity of the ZnO film enhanced with the Al dopant. From the temperature dependence of conductivity measurements, the activation energy of the films was also calculated.     

Enhanced electron field emission characteristics of single-walled carbon nanotube films by ultrasonic bonding

A novel ultrasonic bonding process was used to fabricate the electron field emission cathode of single-walled nanotube film, which was deposited on an Al plate substrate by electrophoretic deposition. Electron field emission properties were improved remarkably after the cathode carbon nanotubes nanobonded with the Al substrate. Turn-on voltage showed a significant decrease and the emission current was much stabilized. This can be attributed to the reduction of the contact resistance in bonding area and easily moving electrons for field emission after ultrasonic bonding. In addition, the field emission performances of SWCNTs films formed at different bonding conditions were also studied. With a simple nano-bonding apparatus, this technique has low cost, and can be utilized for extensively roboticized fabrication of high performance field emission cathodes with short process time.     

Rhodamine B-containing silica films from TEOS precursor: Substrate surface effects detected by photoluminescence

This work presents the study of substrate surface effects on rhodamine B-containing silica films obtained from TEOS (tetraethylorthosilicate) acid hydrolysis. Soda-lime glass substrates were treated with basic solution under different reaction times and temperatures. Rhodamine B-containing silica films were deposited on pre-treated substrates by the spin-coating method. The substrate surface directly affects film morphology and homogeneity. The films are formed by packed silica spheres which protect the dye against acid-base attack. Luminescence spectra present shifts on the dye emission maximum as expected for different pH values on the substrate surface depending on the alkaline treatment.     

Field emission properties of a-C and a-C:H films deposited on silicon surfaces modified with nickel nanoparticles

The a-C and a-C:H films are deposited on silicon surfaces modified with and without nickel nanoparticles by using mid-frequency magnetron sputtering. The microstructures and morphologies of the films are analyzed by Raman spectroscopy and atomic force microscopy. Field emission behaviors of the deposited films with and without nickel nanoparticles modification are comparatively investigated. It is found that the hydrogen-free carbon film exhibits a high field emission current density and low turn-on electric field compared with the hydrogenated carbon film. Nickel modifying could increase the current density, whereas it has no significant effect on the turn-on electric field. The mechanism of field electron emission of a sample is discussed from the surface morphologies of the films and nickel nanoparticle roles in the interface between film and substrate.     

The comparison between CdS thin films grown on Si(111) substrate and quartz substrate by femtosecond pulsed laser deposition

Two kinds of cadmium sulfate (CdS) thin films have been grown at 600 °C onto Si(111) and quartz substrates using femtosecond pulsed laser deposition (PLD). The influence of substrates on the structural and optical properties of the CdS thin films grown by femtosecond pulsed laser deposition have been studied. The CdS thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), photoluminescence (PL) and Raman spectroscopy. Although CdS thin films deposited both on Si(111) and quartz substrates were polycrystalline and hexagonal as shown by the XRD , SEM and AFM results, the crystalline quality and optical properties were found to be different. The size of the grains for the CdS thin film grown on Si(111) substrate were observed to be larger than that of the CdS thin film grown on quartz substrate, and there is more microcrystalline perpendicularity of c-axis for the film deposited on the quartz substrate than that for the films deposited on the Si substrate. In addition, in the PL spectra, the excitonic peak is more intense and resolved for CdS film deposited on quartz than that for the CdS film deposited on Si(111) substrate. The LO and TO Raman peaks in the CdS films grown on Si(111) substrate and quartz substrate are different, which is due to higher stress and bigger grain size in the CdS film grown on Si(111) substrate, than that of the CdS film grown on the amorphous quartz substrate. All this suggests that the substrates have a significant effect on the structural and optical properties of thin CdS films. PACS 81.15.Fg; 81.05.Ea; 78.20.-e; 78.67.-n; 42.62.-b     

Quantitative TEM analysis of Al/Cu multilayer systems prepared by pulsed laser deposition

Thin films composed of alternating Al/Cu/Al layers were deposited on a (111) Si substrate using pulsed laser deposition (PLD). The thicknesses of the film and the individual layers, and the detailed internal structure within the layers were characterized by means of transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and energy-filtered TEM (EFTEM). Each Al or Cu layer consists of a single layer of nano-sized grains of different orientations. EFTEM results revealed a layer of oxide about 2 nm thick on the surface of the Si substrate, which is considered to be the reason for the formation of the first layer of nano-sized Al grains. The results demonstrate that the PLD technique is a powerful tool to produce nano-scale multilayered metal films with controllable thickness and grain sizes.     

Effect of deposition voltage on the field emission properties of electrodeposited diamond-like carbon films

Diamond-like carbon (DLC) films were deposited on Al substrates by electrodeposition technique under various voltages. The surface morphology and compositions of synthesized films were characterized by scanning electron microscopy and Raman spectroscopy. With the increase of deposition voltage, the sp² phase concentration decreased and the surface morphology changed dramatically. The influence of deposition voltage on the field electron emission (FEE) properties of DLC films was not monotonic due to two adverse effects of deposition voltage on the surface morphology and compositions. The DLC film deposited under 1200 V exhibited optimum FEE property, including a lowest threshold field of 13 V/μm and a largest emission current density of 904.8 μA/cm² at 23.5 V/μm.     

化学气相沉积石墨烯薄膜的洁净转移

石墨烯因其优异的性能在很多领域具有广阔的应用前景.目前石墨烯薄膜主要是以铜作为催化基底,通过化学气相沉积法制备.这种方法制备的石墨烯薄膜需要被转移到目标基底上进行后续应用,而转移过程则会对石墨烯造成污染,进而影响石墨烯的性质及器件的性能.如何减少或避免污染,实现石墨烯的洁净转移,是石墨烯薄膜转移技术研究的重要课题,也是本综述的主题.本综述首先简单介绍了石墨烯的转移方法;进而重点讨论由于转移而引入的各种污染物及其对石墨烯性质的影响,以及如何抑制污染物的引入或如何将其有效地去除;最后总结了石墨烯洁净转移所存在的挑战,展望了未来的研究方向和机遇.本综述不仅有助于石墨烯薄膜转移技术的研究,对整个二维材料器件的洁净制备也将有重要参考价值.     

Double resonant Raman scattering in nanographite films

Experimental results are presented on Raman scattering in graphite films produced by DC plasmaenhanced chemical vapor deposition from a methane-hydrogen gas mixture. Scanning electron and probe microscopy data show that, depending on substrate material and deposition time, the deposited film is either a mesoporous material consisting of graphite nanocrystallites with basal planes oriented perpendicular to the substrate surface or an atomically flat, nanometer-thick stack of graphene layers parallel to the substrate. A comparative Raman spectroscopy analysis is performed for film samples deposited on nickel and silicon substrates for 5 and 60 min, as well as for highly ordered graphite samples. The Raman spectra of the examined samples correspond to the double resonant scattering mechanism. The behavior of Raman peak position and intensity as functions of excitation wavelength suggests a high degree of structural order in the graphite films deposited on nickel for 5 min. The results obtained are used to show that the thickness of these films is 1.5 ± 0.5 nm.     

Field electron emission from amorphous carbon thin films grown by RF magnetron sputtering

Using a RF magnetron sputtering, amorphous carbon (a-C) and N-doped a-C (a-C:N) thin films were fabricated as field electron emitter. These thin films were deposited on Si(0 0 1) substrate at several temperatures. The field emission property was improved for a-C thin films grown at higher substrate temperatures. Furthermore, a-C:N film exhibits field emission property better than that of undoped a-C film. These results are explained in terms of the change in surface morphology and structural properties of a-C film.