煤矿顶板离层回归分析与稳定性评价

以光纤Bragg光栅位移传感器对淮北朱仙庄煤矿顶板离层监测为实际数据依据,选择最佳的典型函数模型对顶板离层进行非线性回归分析,得出能够反映位移发展趋势的回归曲线。监测结果与回归拟合数据表明:非线性回归分析预测方法不仅可以反映煤矿顶板离层实时变化过程,还能根据其变化趋势进行巷道稳定性判断。     

具有温度补偿的光纤位移传感器

位移测量是结构健康检测的重要参量之一.本文提出了一种双悬臂梁粘贴光纤光栅的位移传感器,它将位移变化转换成两只光纤光栅的波长移动,实现对位移量的绝对测量.通过引入对称补偿光纤光栅的方法解决了温度与位移交叉敏感的问题.推导了位移传感器的工作原理,完成了相关实验,并分析了传感器所产生误差的来源.实验结果表明,在量程为20 m...     

具有温度补偿的光纤位移传感器

位移测量是结构健康检测的重要参量之一.本文提出了一种双悬臂梁粘贴光纤光栅的位移传感器,它将位移变化转换成两只光纤光栅的波长移动,实现对位移量的绝对测量.通过引入对称补偿光纤光栅的方法解决了温度与位移交叉敏感的问题.推导了位移传感器的工作原理,完成了相关实验,并分析了传感器所产生误差的来源.实验结果表明,在量程为20 mm的时候,位移灵敏度为123 pm/mm,温度补偿前,温度对位移的影响是234.9 μm/℃;温度补偿后,温度对位移的影响为17 μm/℃.本位移传感器量程大、线性好、准确度高,不易受恶劣环境影响.     

基于悬臂梁结构的光纤光栅位移传感研究

本文提出了一种基于光纤光栅和悬臂梁结构的新型位移传感方案,并给出了实验结果。本传感系统结构简单,测量范围大(大于20mm),线性好(0.9991),抗电磁干扰,信噪比高,并可实现在线监测。     

免受温度影响的光纤光栅位移传感器

将一定长度、均匀周期的光纤光栅沿轴向刚性粘贴于厚度呈阶跃分布的等腰三角状悬臂梁界线附近的表面上 ,通过观测该光栅反射谱中两个峰值的间距来监测梁自由端在垂直于表面方向上的位移。实验表明该无源温漂位移线性传感装置的传感灵敏度达 9.2 4× 10 -2 nm/ mm,与理论值 9.4× 10 -2 nm/ mm非常接近。     

微小位移光纤传感器谐波分析解调法研究

本文从理论上阐述了微小位移光纤传感器的一种分频比较法解调方案,并利用全光纤干涉光路进行了实验,结果表明采用这种解调方法可提高光纤传感器的测试精度、稳定性和动态范围。     

带宽调制型单光纤光栅温变无补偿位移传感

报道了利用反射谱带宽调制和光强差分探测技术实现单一光纤光栅温变无补偿位移精确测量的新方法。设计了一种结构新颖的曲臂梁位移传感装置,结合光波导理论与材料力学原理分析了光纤光栅在高斯应变作用下光栅反射谱侧向梯度展宽的成因,理论推导了特殊结构梁在外力作用下光栅反射谱带宽/反射光强与压力之间的响应关系。光栅反射谱侧向梯度展宽的同时反射光强线性增加,利用光强差分检测方法消除光源出光抖动的影响,提高了位移测量精度。基于带宽调制的光纤光栅位移传感方法免受温度变化的影响,在-10℃~80℃的温度变化范围内,测量误差小于1.2%,实现了单光纤光栅温变无补偿位移测量。     

基于光纤Bragg光栅位移测量的研究

介绍了一种基于布喇格光纤光栅技术的位移测量方法。利用宽带光源经不同的布喇格光栅得到一种由温度稳定器控制波长稳定性的合成光源。由于系统设计的合成光源波长比常规光源的波长长，所以允许的光程差测量范崮提高了几百倍，从而使得布喇格光纤光栅的波长准确性提高了干涉仪位移测量的准确性。此外，利用光外差法马赫一曾德尔干涉仪进行了位移测量实验，得到了很好的效果。     

利用锁模光纤激光器在色散位移光纤中产生超连续谱的研究

采用主动锁模光纤激光器输出的重复频率10GHz、脉宽7．97ps的脉冲作为抽运光源,无需压缩后直接抽运4．2km的普通色散位移光纤(DSF)．利用色散位移光纤中自相位调制、交叉相位调制等非线性效应的联合作用,获得了20dB带宽达125nm、覆盖整个C波段、L波段和部分S波段的超连续(SC)谱。实验研究了抽运光脉冲峰值功率和抽运波长对超连续谱宽度的影响,结果表明抽运光脉冲峰值功率越高,得到的超连续谱的带宽越宽;通过对抽运波长的优化,可以实现最大程度的超连续展宽;分析了滤波器带宽对脉冲质量的影响;利用0．4nm带宽的可调谐滤波器对从超连续谱中滤出脉冲的特性进行了研究,在超连续谱的不同波长处获得了脉宽为8．90～9．80ps、时间一带宽积为0．44～0．49的稳定的窄光脉冲。     

基于光纤布拉格光栅传感器的光纤光栅智能夹层试验研究

传感元件与复合材料的一体化是智能结构研究的最终目标之一。设计一种具有自诊断功能的标准化、模块化光纤智能夹层系统,正是实现这种一体化最有潜力的技术途径。采用聚酰亚胺薄膜制作了基于光纤布拉格光栅（FBG）传感器的光纤光栅智能夹层,对智能夹层中光纤布拉格光栅传感器的应变、温度特性进行了标定试验,并建立了基于光纤布拉格光栅传感器光纤光栅智能夹层的应变、温度测量模型。试验表明,智能夹层内布拉格光栅波长偏移与应变、温度之间具有良好的线性关系。不过在温度测量时,必须考虑被埋人结构的热膨胀效应。利用光纤光栅智能夹层内光纤布拉格光栅传感器网络和先进信息处理技术,可以建立结构损伤主动、在线和实时监测系统。     

Strain relaxation in SiGe layer during wet oxidation process

The strain relaxation in SiGe layer on silicon substrate during wet oxidation at 1000 °C was investigated. It was proposed that the competition between Ge accumulation and diffusion led to different strain-relaxation behaviors. At the very beginning, Ge atoms at the oxidizing interface were quickly accumulated due to the high oxidation rate resulting in the additional nucleation of misfit dislocations (therefore a lot of threading dislocations) to relieve stress after the thickness of the Ge condensed layer was larger than the critical value. And then, when the Ge accumulation rate was less than the diffusion rate, Ge content started to decrease from a maximum value and the strain in the SiGe layer was mainly relieved through surface roughing and the degree of strain relaxation reached a maximum. When the samples were further oxidized, Ge accumulation could be neglected because of the self-limiting oxidation and the Ge diffusion dominated the consequent processes. As a result, Ge content at the interface was reduced, with the contribution of the strain relaxation in SiO₂ viscously, leading to the decrease of degree of strain relaxation in the SiGe layers slowly.     

围岩压力在煤矿爆破中的光纤在线监测

围岩压力状况的在线实时监测,特别是在煤矿爆破过程中,对及时采取安全支护措施和预防顶板失稳具有重要意义。利用ANSYS有限元仿真分析顶板的受力分布,将一种双膜式光纤Bragg光栅土压力传感器通过全锚锚杆使传感器均匀地承接来自直接顶的压力作用。在试点处,通过螺母与锚杆伸出端的螺纹连接,用托盘将土压力传感器紧紧顶靠在围岩顶板上。采集数据显示,监测数据的曲线走势出现三次峰值突变,分别为128kPa、87kPa和134kPa,反映出煤矿爆破对围岩压力产生的扰动作用。实现了在爆破过程中对围岩压力的实时监测,为进一步的顶板失稳预报提供了可靠的数据支持。     

Visualization and numerical analysis of stress waves in blasting process

Visualization studies were performed both experimentally and theoretically to observe stress wave propagation in a material and its interaction with the free surface of the material in a blasting process. PMMA (polymethyl-methacrylate) plates were used as a transparent material. The stress wave was generated by initiation of an electric detonator. The stress waves in the PMMA specimen with the right-angled corner were observed by means of the shadowgraph system using a Q switched ruby laser as a light source. In addition to the experiment, a numerical analysis using smoothed particle hydrodynamics (SPH) was also carried out to clarify the dynamic behavior of stress waves in the blasting process. Transmittance and reflection of the stress wave at the free surface could be visualized by both the experiment and the numerical analysis.     

Influence of the cladding layer field of fiber on beam parameters

Beam parameters, including mode-field radius, divergence half-angle and beam propagation factor are studied and relations among them are derived under the condition of paraxial approximation. Several formulas of the beam parameters for end diffraction-limited from the fundamental mode of fiber are given based on the normalized standing wave parameter, normalized evanescent wave parameter and radii of core layer and circular aperture. Moreover, influence of change of the near-field on beam parameters is researched and the results show that the cladding layer field has determinant effect and cannot be neglect. These conclusions may provide theoretical foundation for further researching the beam parameters.     

Phase monitoring during Nd15Fe77B8 preparation by the calciothermic reduction-diffusion process

We have examined the effect of various parameters involved in the preparation of the Nd₁₅Fe₇₇B₈ alloy by the calciothermic reduction-diffusion process. Both Nd₂O₃ and NdCl₃ were utilized as starting raw materials. Shorter reaction times and lower heating temperatures are required for the chloride than for the oxide. Among the characterization techniques used to evaluate the final product, Mössbauer spectroscopy was invaluable for the determination of the (Nd_1.1Fe₄B₄)/(Nd₂Fe₁₄B) ratio, which should be as low as possible.     

The influence of radiation-induced vacancy on the formation of thin-film of compound layer during a reactive diffusion process

A theoretical approach is developed that describes the formation of a thin-film of AB-compound layer under the influence of radiation-induced vacancy. The AB-compound layer is formed as a result of a chemical reaction between the atomic species of A and B immiscible layers. The two layers are irradiated with a beam of energetic particles and this process leads to several vacant lattice sites creation in both layers due to the displacement of lattice atoms by irradiating particles. A- and B-atoms diffuse via these lattice sites by means of a vacancy mechanism in considerable amount to reaction interfaces A/AB and AB/B. The reaction interfaces increase in thickness as a result of chemical transformation between the diffusing species and surface atoms (near both layers). The compound layer formation occurs in two stages. The first stage begins as an interfacial reaction controlled process, and the second as a diffusion controlled process. The critical thickness and time are determined at a transition point between the two stages. The influence of radiation-induced vacancy on layer thickness, speed of growth, and reaction rate is investigated under irradiation within the framework of the model presented here. The result obtained shows that the layer thickness, speed of growth, and reaction rate increase strongly as the defect generation rate rises in the irradiated layers. It also shows the feasibility of producing a compound layer (especially in near-noble metal silicide considered in this study) at a temperature below their normal formation temperature under the influence of radiation.     

Controlling the fiber diameter during electrospinning

We present a simple analytical model for the forces that determine jet diameter during electrospinning as a function of surface tension, flow rate, and electric current in the jet. The model predicts the existence of a terminal jet diameter, beyond which further thinning of the jet due to growth of the whipping instability does not occur. Experimental data for various electrospun fibers attest to the accuracy of the model.