Specific features of lignin dissolution in aqueous and aqueous-organic media

The solubility of lignin in aqueous NaOH solutions and dioxane-water mixtures was studied. Factors governing the solubility of lignin in these media were determined.     

Oxidation of hydrolysis lignin with hydrogen peroxide in acid solutions

Optimal conditions were determined for oxidation of hydrolysis lignin and other insoluble lignin samples with hydrogen peroxide in acid solutions, ensuring solubility of lignin in dilute alkali. The correlation was found between the functionalization and solubility of hydrolysis lignin and its oxidation products. A procedure was suggested for determining carboxy groups in lignin.     

Smooth model surfaces from lignin derivatives. I. Preparation and characterization

Lignin model surfaces were prepared from aqueous alkaline solutions by spin-coating on silica wafers. Films of thicknesses between 20 and 140 nm were easily made by variations in the spinning rate or in the lignin concentration. The roughnesses of the lignin surfaces were relatively low, approximately 1.1 nm (rms) on an area of 25 microm2, as determined by atomic force microscopy imaging. The stability of the lignin films in aqueous solutions was found to be excellent. No changes in the thickness of model surfaces immersed in slightly alkaline solutions (pH 9.2) could be detected even after 5 h soaking. A 10 percent reduction in the thickness of the lignin film was observed after 5 h of exposure to a solution containing 0.1 M NaCl. This novel preparation method opens great possibilities for further fundamental studies, where interactions between lignin and other substances are of interest to investigate.     

1-丁基-3-甲基咪唑甲基磺酸盐水溶液中酚型木质素单体溶解的二维相关红外光谱分析北大核心CSCD

当离子液体(IL)水溶液—1-丁基-3-甲基咪唑甲基磺酸盐([C_(4)C_(1)im]CH_(3)SO_(3))的摩尔分数x_(IL)=0.20时,酚型木质素单体模型化合物2,6-二甲氧基苯酚(2,6-DMP)的溶解度最高。这一现象与木质素溶解规律相似。利用二维相关红外光谱(2D-IR)研究2,6-DMP在[C_(4)C_(1)im]CH_(3)SO_(3)水溶液中溶解过程,以帮助深入理解木质素在IL水溶液中溶解机制。以x_(IL)变量的2D-IR分析结果表明,x_(IL)=0.02~0.20条件下IL加入破坏水的弱氢键结构,IL阴阳离子以水合离子对形式存在,疏水性2,6-DMP与[C_(4)C_(1)im]+和CH_(3)SO_(3)−同时发生相互作用,促进2,6-DMP溶解;x_(IL)=0.20~1.0条件下,IL形成致密离子簇结构,不利于2,6-DMP与IL阴阳离子相互作用。以2,6-DMP摩尔分数(x_(DMP))为变量的分析结果表明,加入2,6-DMP对IL结构影响小,而对水的微观结构影响大。对于具有离子对结构的IL水溶液(x_(IL)=0.10),水优先与CH_(3)SO_(3)−作用;对于具有离子簇结构的IL水溶液(x_(IL)=0.60),水优先形成自缔合小水簇结构。IL水溶液微观结构影响IL-水与2,6-DMP之间相互作用和2,6-DMP溶解特性,同时2,6-DMP溶解也导致IL水溶液的微观结构变化。     

Solubility of carbon dioxide in aqueous solutions of diisopropanolamine and methyldiethanolamine

The solubility of carbon dioxide in aqueous solutions of alkanolamines was measured by means of two experimental methods. The solubility of carbon dioxide was measured at 298 K with a static total pressure apparatus in solutions of water + diisopropanolamine (DIPA) having mass fraction of DIPA equal to 10.1%, 11.0% and 33.9%. The density of the water + DIPA solution was measured continuously during the experiments to investigate the changes in density introduced by the absorption of carbon dioxide. A correlation for the density of CO₂-loaded aqueous solutions of DIPA is presented.     

Enhancement of cyclosporine aqueous solubility using α- and hydroxypropyl β-cyclodextrin mixtures

Cyclodextrins (CDs) are cyclic oligosaccharides that form inclusion complexes with lipophilic molecules through their hydrophobic central cavity. In this study, the effect of α-CD, hydroxylpropyl-β-CD (HP-β-CD) and mixtures of these two CDs on the aqueous solubility of cyclosporine A (CyA) was investigated. Infrared spectroscopy and thermal analysis were used to confirm CyA-CD complex formation. CyA aqueous solubility was increased by 10 and 80 fold in the presence of α-CD and HP β-CD, respectively. The phase-solubility profile for HP-β-CD was linear while that for α-CD had positive deviation from linearity. In the presence of constant concentration of α-CD (15% w/v), aqueous solubility of CyA was further increased upon addition of HP-β-CD up to a concentration of 20% w/v. At higher HP-β-CD concentrations, aqueous solubility of CyA was observed to decrease. Addition of sodium acetate (up to 5% w/v) to aqueous solutions containing 20% w/v HP-β-CD and increasing concentrations of α-CD resulted in a significant reduction in CyA solubility. Complex formation between CyA and both α-CD and HP-β-CD was confirmed by differential scanning calorimetry (DSC). No significant changes were observed in the IR spectra of either CyA or CD following complex formation suggesting chemical interaction between CyA and the CD was unlikely. Phase-solubility studies showed that α-CD had a much greater effect on the solubility of CyA than HP-β-CD. Addition of HP-β-CD to aqueous solutions of α-CD affected the solubility of CyA in these systems. A mixture of 15% w/v α-CD and 20% w/v HP-β-CD was optimal for increasing aqueous solubility of CyA.     

Influence of Adsorption of Lignosulfonates on Kraft Lignin in the Presence of Tall Oil on Separation of Water-Tall Oil Emulsion

The degree of hydrophilicity-oleophilicity of solid lignin recovered from cooking liquors of deciduous and coniferous wood at various pH and its influence on the aggregative stability of water-tall oil emulsion were estimated. The stabilizing effect of lignosulfonates on lignin suspension in aqueous electrolyte solution was studied. The values of absorption of lignosulfonates from aqueous solutions on kraft lignin were determined depending on the molecular weight of lignosulfonates and content of tall oil in the suspension.     

The determination of the solubility of organic solvents in mineral acids

A knowledge of the solubility of organic solvents in aqueous solutions of mineral acids is shown to be important in solvent extraction studies. The method described depends upon the direct measurement of the amount of solvent thrown out of the aqueous phase on neutralization. The results of experiments on the solubility of iso-propyl ether in aqueous hydrochloric acid are given. The accuracy, limitations, and uses of the method are discussed.     

Morphology of dry lignins and size and shape of dissolved kraft lignin particles by X-ray scattering

Lignin is a highly branched polymer consisting of phenylpropane units, and it is one of the ingredients of the supporting matrix in plant cell walls. The morphology of several lignins extracted from plant cell walls using different methods was studied by small-angle and ultra-small-angle X-ray scattering. A power-law type intensity was observed for the dry lignins, but on the basis of the power-law exponent the fractal approach often applied to lignins is not fully justified. However, the intensity of kraft lignin did show a power law with surface fractal dimension D(s) = 2.7 +/- 0.1. The specific surface area of the lignins ranged from about 0.5 to 60 m(2)/g with 20% relative accuracy. The radius of gyration was determined from small-angle X-ray scattering data for aqueous solutions of kraft lignin. The shape of the particles in NaCl and NaOH solutions was found to be elongated. The particles were about 1-3 nm thick, while the length (5-9 nm) depended on the solvent and on the lignin concentration. The size of these primary particles was approximately the same as the size of the pores in the fractal aggregates of the dry kraft lignin. Their size was determined to be about 3.5 nm.     

Influence of Acidity and Uranyl Nitrate Concentration on the Efficiency of Recovery of Uranium(VI) from Aqueous Solutions with Hydrolytic Wood Lignin

The efficiency of recovery of uranium(VI) from aqueous solutions with hydrolytic lignin and strength of binding of uranium to lignin were studied in relation to the uranium concentration and acidity. The mechanisms of sorption of uranium were analyzed by the methods of sequential leaching of uranium from lignin and IR spectroscopy.     

Experimental and theoretical investigation of the micellar-assisted solubilization of ibuprofen in aqueous media

Surfactants can be used to increase the solubility of poorly soluble drugs in water and to increase drug bioavailability. In this article, the aqueous solubilization of the nonsteroidal, antiinflammatory drug ibuprofen is studied experimentally and theoretically in micellar solutions of anionic (sodium dodecyl sulfate, SDS), cationic (dodecyltrimethylammonium bromide, DTAB), and nonionic (dodecyl octa(ethylene oxide), C12E8) surfactants possessing the same hydrocarbon "tail" length but differing in their hydrophilic headgroups. We find that, for these three surfactants, the aqueous solubility of ibuprofen increases linearly with increasing surfactant concentration. In particular, we observed a 16-fold increase in the solubility of ibuprofen relative to that in the aqueous buffer upon the addition of 80 mM DTAB and 80 mM C12E8 but only a 5.5-fold solubility increase upon the addition of 80 mM SDS. The highest value of the molar solubilization capacity (chi) was obtained for DTAB (chi = 0.97), followed by C12E8 (chi = 0.72) and finally by SDS (chi = 0.23). A recently developed computer simulation/molecular-thermodynamic modeling approach was extended to predict theoretically the solubilization behavior of the three ibuprofen/surfactant mixtures considered. In this modeling approach, molecular-dynamics (MD) simulations were used to identify which portions of ibuprofen are exposed to water (hydrated) in a micellar environment by simulating a single ibuprofen molecule at an oil/water interface (modeling the micelle core/water interface). On the basis of this input, molecular-thermodynamic modeling was then implemented to predict (i) the micellar composition as a function of surfactant concentration, (ii) the aqueous solubility of ibuprofen as a function of surfactant concentration, and (iii) the molar solubilization capacity (chi). Our theoretical results on the solubility of ibuprofen in aqueous SDS and C12E8 surfactant solutions are in good agreement with the experimental data. The ibuprofen solubility in aqueous DTAB solutions was somewhat overpredicted because of challenges associated with accurately modeling the strong electrostatic interactions between the anionic ibuprofen and the cationic DTAB. Our results indicate that computer simulations of ibuprofen at a flat oil/water interface can be used to obtain accurate information about the hydrated and the unhydrated portions of ibuprofen in a micellar environment. This information can then be used as input to a molecular-thermodynamic model of self-assembly to successfully predict the aqueous solubilization behavior of ibuprofen in the three surfactant systems studied.     

Dissolution of chitin in aqueous KOH

Our NMR experiments show that chitin can dissolve well in aqueous KOH through a freeze-thawing process, and the dissolution power of the alkali solvent systems is in the order of KOH > NaOH > LiOH aqueous solution, which is totally contrary to that of cellulose in the alkali aqueous solution (i.e., LiOH > NaOH ? KOH). In this work, we systematically study the dissolution process in KOH and KOH/urea aqueous solutions. Chitin has good solubility (solubility ~80 %) in 8.4–25 wt% KOH aqueous solution at ?30 °C. The role of urea also has been investigated: unlike aqueous chitin-NaOH solutions, urea indeed enhances the solubility of chitin in KOH aqueous solutions, but the increased degree becomes unobtrusive with decreasing temperature and increasing dissolution time; the DA decline curves of chitin-KOH and chitin-KOH/urea aqueous solutions are nearly overlapping, indicating that the effect of the urea on the degree of acetylation of chitin in KOH aqueous solutions is small, similar to the NaOH/urea solvent.     

Effect of self-aggregation of γ-cyclodextrin on drug solubilization

The purpose of this study was to investigate the physicochemical properties of drug-saturated aqueous cyclodextrin (CD) solutions. Phase solubility profiles of different drugs were determined in aqueous solutions containing γ-cyclodextrin (γCD) and/or hydroxypropyl-γ-cyclodextrin (HPγCD) in absence or presence of water-soluble polymers. ¹H-NMR and turbidity analysis were performed as well as permeation studies. Phase solubility diagrams showed that the observed γCD content (1–20% w/v) was only slightly different from the theoretical values for aqueous solutions that had been saturated with indomethacin, diclofenac sodium or amphotericin B, all displayed A-type profiles, while it was less than the theoretical value in solutions that had been saturated with corticosteroids (hydrocortisone and dexamethasone) that displayed B_S-type profiles. In the latter case self-assemble of drug/CD complexes decreased the overall CD solubility. Water-soluble polymers enhanced aqueous solubility of the drugs tested by stabilizing the drug/CD complexes, i.e. enhancing their stability constants, without affecting the observed aqueous γCD solubility. When the drug solubility leveled off (the B_S-type profiles) the amount of dissolved γCD increased and approached the theoretical values. Hydrocortisone formed partial inclusion complex with γCD and HPγCD and no non-inclusion or aggregates could be detected in diluted solutions by ¹H-NMR. Both permeation and turbidity studies showed that formation of dexamethasone/γCD complex promoted CD aggregation. All these observations indicate that CD aggregate formations play a role in CD solubilization of lipophilic and poorly water-soluble drugs and that the water-soluble polymers enhance the complexation efficiency of γCD and HPγCD by stabilizing the self-assembled drug/CD nanoparticles and promote non-inclusion complex formation.     

Correlation of phase equilibria of amino acids and peptides in aqueous solution based on the perturbation theory of equation of state

In this paper, the activity coefficients of amino acids and simple peptides in aqueous solutions were correlated by using a three parameters model based on the perturbation theory. The adjustable parameters of this model were obtained from the experimental data and a relation for calculating the activity coefficient is derived. The calculated activity coefficients of amino acids and simple peptides obtained show that the equation of state based on the perturbation model can be used to correlate the activity coefficients of amino acids more accurately than the other models. A correlation for the solubility of amino acids in aqueous solutions is also derived. The results show that this correlation can accurately correlate the solubility of amino acids in aqueous solution over a wide range of temperatures (0–100 °C).     

Conductometric determination of quaternary ammonium salts by sodium perchlorate and vice versa

A conductometric method is proposed for the determination of quaternary ammonium salts (chloride or bromide), based on the poor solubility of the relative perchlorates. A comparison between expected and found values shows that the method is suitable, rapid, and easy for quantities in the range from 0.2 to 5 g. The error depends on the solubility of the relative perchlorate. The apparent and tentative solubility product of the studied compounds were calculated. The obtained values allowed to propose benzyltributyl ammonium chloride (BTBA Cl) as precipitant for the conductometric titration of perchlorate. This easy, rapid and accurate determination can be used to analyze the perchlorate ion even in concentrated solutions and to determine stability constants for complex formation in aqueous solutions.     

Mechanism of the catalytic ozonization of lignin in the presence of Mn(II) ions

The reaction between ozone and lignin in aqueous solutions catalyzed by Mn(II) ions is studied. The rate of destruction for aromatic structures of lignin is found to increase in the presence of Mn(II) ions. However, the greatest catalytic effect is observed upon the transformation of aliphatic acids that are difficult to oxidize with ozone. The introduction of catalyst raises the total consumption of ozone from 3 to 7 mol per each structural unit of lignin. A scheme is proposed for the transformation of phenol fragments of lignin using ozone with the participation of Mn(II) ions: at the initial stage, we observe the ozone oxidation of lignin and Mn(II) to Mn(III) ions stabilized with products of lignin oxidation and accompanied by the formation of chelate complexes, and the Mn(III) chelate complexes act as low-molecular mediators, attacking phenol structures and initiating radical processes.     

Photometric determination of trace uranium(VI), phosphorus(V), arsenic(V), and vanadium(V) in saturated aqueous solutions of poorly soluble compounds

A procedure for extraction-photometric determination of uranium(VI) was developed and procedures for the determination of phosphorus(V), arsenic(V), and vanadium(V) were modernized. The solubility of some poorly soluble uranium compounds in aqueous solutions was determined. Deceased.     

Simultaneous correlation of hydrophobic interactions in HIC and protein solubility in aqueous salt solutions and mixed solvents

The chromatographic retention in hydrophobic and reversed phase chromatography and the solubility of proteins display some common features. The chromatographic retention, as well as the solubility, is modulated by the thermodynamic properties of the solute in the fluid phase. The retention measurements at linear conditions provide information of the solution properties of the protein at infinite dilution, and the solubility measurements produce the supplementary information about the solution properties at the saturation limit. This provides a useful approach to simultaneous correlation of the chromatographic retention and the solubility.The experimental data, used for the correlation, comprise retention measurements of lysozyme on different HIC adsorbents using an aqueous ammonium sulphate eluant, an aqueous ammonium sulphate eluant with an admixture of ethanol, as well as published solubility data.The chromatographic retention data and the corresponding solubility data have been correlated using a chemical potential model derived from Kirkwood's theory of solutions of charged macro-ions and zwitterions in electrolyte solutions. The model correlated the chromatographic retention factor and the solubility data within the precision of the measurements. The model was applied in a pH range from 4 to 11. It was demonstrated experimentally, as well as theoretically, that an admixture of ethanol to the aqueous eluant changes the thermodynamic retention factor on various adsorbents identically when compared to the thermodynamic retention factor in an ethanol free eluant.     

Histograms of the size distribution of kraft lignin particles in aqueous solutions at various pH values

The size distribution of kraft lignin particles in aqueous solutions in a wide pH range (9.5−2.0) was studied by filtration through track membranes.