Nanoporous gold electrode prepared from gold compact disk as the anode for the microbial fuel cell

The electrodes (anode and cathode) have an important role in the efficiency of a microbial fuel cell (MFC), as they can determine the rate of charge transfer in an electrochemical process. In this study, nanoporous gold electrode, prepared from commercially available gold-made compact disk, is utilized as the anode in a two-chamber MFC. The performance of nanoporous gold electrode in the MFC is compared with that of gold film, carbon felt and acid-heat-treated carbon felt electrodes which are usually employed as the anode in the MFCs. Electrochemical surface area of nanoporous gold electrode exhibits a 7.96-fold increase rather than gold film electrode. Scanning electron microscopy analysis also indicates the homogeneous biofilm is formed on the surface of nanoporous gold electrode, while the biofilm formed at the surface of acid-heat-treated carbon felt electrode shows rough structure. Electrochemical studies show although modifications applied on carbon felt electrodes improve its performance, nanoporous gold electrode, due to its structure and better electrochemical properties, acts more efficiently as the MFC’s anode. The maximum power density produced by nanoporous gold anode is 4.71 mW m^?2 at current density of 16.00 mA m^?2, while this value for acid-heat-treated carbon felt anode is 3.551 mW m^?2 at current density of 9.58 mA m^?2.     

Bioelectricity Production from Soil Using Microbial Fuel Cells

Microbial fuel cells (MFCs) are a device using microorganisms as biocatalysts for transforming chemical energy into bioelectricity. As soil is an environment with the highest number of microorganisms and diversity, we hypothesized that it should have the potential for energy generation. The soil used for the study was Mollic Gleysol collected from the surface layer (0–20 cm). Four combinations of soil MFC differing from each other in humidity (full water holding capacity [WHC] and flooding) and the carbon source (glucose and straw) were constructed. Voltage (mV) and current intensity (μA) produced by the MFCs were recorded every day or at 2-day intervals. The fastest and the most effective MFCs in voltage generation (372.2?±?5 mV) were those constructed on the basis of glucose (MFC-G). The efficiency of straw MFCs (MFC-S) was noticeable after 2 weeks (319.3?±?4 mV). Maximal power density (P _max?=?32 mW m^?2) was achieved by the MFC-G at current density (CD) of 100 mA m^?2. Much lower values of P _max (10.6–10.8 mW m^?2) were noted in the MFC-S at CD of ca. 60–80 mA m^?2. Consequently, soil has potential for production of renewable energy.     

Microbial fuel cells using natural pyrrhotite as the cathodic heterogeneous Fenton catalyst towards the degradation of biorefractory organics in landfill leachate

An investigation aimed at checking the integration of cathodic pyrrhotite Fenton's reaction with anodic microbial respiration for the enhancement of MFC performance and treatment of a real landfill leachate was carried out. The MFC equipped with a pyrrhotite-coated graphite-cathode generated the maximum power density of 4.2 W/m³ that was 133% higher than graphite-cathode. Concomitantly, electrochemical impedance spectroscopy (EIS) showed that the polarization resistance of pyrrhotite-cathode (92 Ω) was much lower than the graphite-cathode (1057 Ω), indicating that the cathodic overpotential was significantly lowered, probably due to the occurrence of pyrrhotite Fenton's reaction. The in situ generation of Fenton's reagents (Fe²⁺ and H₂O₂) at the pyrrhotite-cathode was demonstrated by the cyclic voltammetry measurement. Besides, reactive oxygen species produced from the pyrrhotite Fenton's reaction were detected and demonstrated to be vital to the enhancement of MFC power output. Further, the effectiveness of this system was examined by treating an old-aged landfill leachate. 77% of color and 78% of COD were removed from the original leachate, indicating that the pyrrhotite not only acted as a cost-effective cathodic catalyst for MFCs in power generation, but also extended the practical merits of traditional MFCs towards advanced oxidation of biorefractory pollutants.     

Enhanced power production of microbial fuel cells by reducing the oxygen and nitrogen functional groups of carbon cloth anode

The physicochemical properties of anode material are important for the electron transfer of anode bacteria and electricity generation of microbial fuel cells (MFCs). In this work, carbon cloth anode was pretreated with isopropanol, hydrogen peroxide (H₂O₂) and sodium hypochlorite (NaOCl) in order to reduce the anode functional groups. The influence of functional groups on the electrochemical properties of carbon cloth anode and power generation of MFCs was investigated. The anode pretreatments removed the surface sizing layer of carbon cloth and substantially reduced the contents of C‐O and pyridinic/pyrrolic N groups on the anode. Electrochemical impedance spectroscopy and cyclic voltammetry analyses of the biofilm‐matured anodes revealed an enhanced electrochemical electron transfer property because of the anode pretreatments. As compared with the untreated control (612 ± 6 mW m^?2), the maximum power density of an acetate‐fed single‐chamber MFC was increased by 26% (773 ± 5 mW m^?2) with the isopropanol treated anode. Additional treatment with H₂O₂ and NaOCl further increased the maximum power output to 844 ± 5 mW m^?2 and 831 ± 4 mWm^?2. A nearly inverse liner relationship was observed between the contents of C‐O and pyridinic/pyrrolic N groups on anodes and the anodic exchange current density and the power output of MFCs, indicating an adverse effect of these functional groups on the electricity production of anodes. Results from this study will further our understanding on the microbial interaction with carbon‐based electrodes and provide an important guidance for the modification of anode materials for MFCs in future studies. Copyright © 2016 John Wiley & Sons, Ltd.     

Optimization of Bioelectricity Generation in Fed-Batch Microbial Fuel Cell: Effect of Electrode Material,Initial Substrate Concentration,and Cycle Time

Effective wastewater treatment and electricity generation using dual-chamber microbial fuel cell (MFC) will require a better understanding of how operational parameters affect system performance. Therefore, the main aim of this study is to investigate the bioelectricity production in a dual-chambered MFC-operated batch mode under different operational conditions. Initially, platinum (Pt) and mixed metal oxide titanium (Ti-TiO₂) electrodes were used to investigate the influence of the electrode materials on the power generation at initial dissolved organic carbon (DOC) concentration of 400 mg/L and cycle time of 15 days. MFC equipped with Ti-TiO₂ electrode performed better and was used to examine the effect of influent DOC concentration and cycle time on MFC performance. Increasing influent DOC concentration resulted in improving electricity generation, corresponding to a 1.65-fold increase in power density. However, decrease in cycle time from 15 to 5 days adversely affected reactor performance. Maximum DOC removal was 90?±?3 %, which was produced at 15-day cycle time with an initial DOC of 3,600 mg/L, corresponding to maximum power generation of about 7,205 mW/m².     

Poly(vinyl alcohol) separators improve the coulombic efficiency of activated carbon cathodes in microbial fuel cells

High-performance microbial fuel cell (MFC) air cathodes were constructed using a combination of inexpensive materials for the oxygen reduction cathode catalyst and the electrode separator. A poly(vinyl alcohol) (PVA)-based electrode separator enabled high coulombic efficiencies (CEs) in MFCs with activated carbon (AC) cathodes without significantly decreasing power output. MFCs with AC cathodes and PVA separators had CEs (43%–89%) about twice those of AC cathodes lacking a separator (17%–55%) or cathodes made with platinum supported on carbon catalyst (Pt/C) and carbon cloth (CE of 20%–50%). Similar maximum power densities were observed for AC-cathode MFCs with (840 ± 42 mW/m²) or without (860 ± 10 mW/m²) the PVA separator after 18 cycles (36 days). Compared to MFCs with Pt-based cathodes, the cost of the AC-based cathodes with PVA separators was substantially reduced. These results demonstrated that AC-based cathodes with PVA separators are an inexpensive alternative to expensive Pt-based cathodes for construction of larger-scale MFC reactors.     

Ammonia treatment of carbon cloth anodes to enhance power generation of microbial fuel cells

Changes in microbial fuel cell (MFC) architecture, materials, and solution chemistry can be used to increase power generation by microbial fuel cells (MFCs). It is shown here that using a phosphate buffer to increase solution conductivity, and ammonia gas treatment of a carbon cloth anode substantially increased the surface charge of the electrode (from 0.38 to 3.99 meq m⁻²), and improved MFC performance. Power increased to 1640 mW m⁻² (96 W m⁻³) using a phosphate buffer, and further to 1970 mW m⁻² (115 W m⁻³) using an ammonia-treated electrode. The combined effects of these two treatments boosted power production by 48% compared to previous results using this air-cathode MFC. In addition, the start up time of an MFC was reduced by 50%.     

Improved performances of E. coli-catalyzed microbial fuel cells with composite graphite/PTFE anodes

The composite graphite/PTFE electrodes with a variety of PTFE contents were tested as anodes in microbial fuel cell (MFC) based on the biocatalysis of bacteria Escherichia coli (E. coli). It is shown that the PTFE content in the composite electrodes can significantly influence the efficiency of current generation of the MFCs. The composite electrodes with optimized PTFE contents, e.g., 24% to 36% (w/w), are well-suited to serve as anode of E. coli-catalyzed MFCs. In the absence of exogenous electron mediators, E. coli-catalyzed MFC with the composite anode containing 30% PTFE and a conventional air cathode exhibited a power density of 760 mW m⁻², which is even much higher than those reported in the literature so far for E. coli MFCs using efficient electron mediators. These results show significant prospects for developing low cost and effective anode of MFCs.     

Mo2C/Reduced Graphene Oxide Composites with Enhanced Electrocatalytic Activity and Biocompatibility for Microbial Fuel Cells

A simple, cost-effective strategy was developed to effectively improve the electron transfer efficiency as well as the power output of microbial fuel cells (MFCs) by decorating the commercial carbon paper (CP) anode with an advanced Mo₂C/reduced graphene oxide (Mo₂C/RGO) composite. Benefiting from the synergistic effects of the superior electrocatalytic activity of Mo₂C, the high surface area, and prominent conductivity of RGO, the MFC equipped with this Mo₂C/RGO composite yielded a remarkable output power density of 1747±37.6 mW m⁻², which was considerably higher than that of CP-MFC (926.8±6.3 mW m⁻²). Importantly, the composite also facilitated the formation of 3D hybrid biofilm and could effectively improve the bacteria–electrode interaction. These features resulted in an enhanced coulombic efficiency up 13.2 %, nearly one order of magnitude higher than that of the CP (1.2 %).     

石墨烯基杂化材料在微生物燃料电池电极中的应用

微生物燃料电池（MFC）是利用生物催化剂将污水有机物中的化学能直接转化为电能的技术,因其功率密度和能量转化效率低,电极制作成本高,限制了其大规模实际应用。因此如何提高电极的催化性能并降低电极制作成本成为MFC的研究重点方向。由于石墨烯基杂化材料具有良好的导电性和催化特性,因此石墨烯基杂化材料成为在MFC电极应用中的热点之一。本文综述了近年来MFC石墨烯基杂化电极材料的最新研究进展,重点讨论了改性石墨烯电极、金属及非金属/石墨烯杂化电极、金属氧化物/石墨烯杂化电极、聚合物/石墨烯杂化电极和石墨烯凝胶电极的设计思路和制备方法及其催化性能,着重分析了石墨烯基阳极和阴极杂化材料对MFC产电性能的影响。最后对石墨烯基杂化材料在MFC应用中存在的问题及研究前景进行了总结和展望。     

Dual‐Doped Molybdenum Trioxide Nanowires: A Bifunctional Anode for Fiber‐Shaped Asymmetric Supercapacitors and Microbial Fuel Cells

A novel in situ N and low‐valence‐state Mo dual doping strategy was employed to significantly improve the conductivity, active‐site accessibility, and electrochemical stability of MoO₃, drastically boosting its electrochemical properties. Consequently, our optimized N‐MoO_3?x nanowires exhibited exceptional performances as a bifunctional anode material for both fiber‐shaped asymmetric supercapacitors (ASCs) and microbial fuel cells (MFCs). The flexible fiber‐shaped ASC and MFC device based on the N‐MoO_3?x anode could deliver an unprecedentedly high energy density of 2.29 mWh cm^?3 and a remarkable power density of 0.76 μW cm^?1, respectively. Such a bifunctional fiber‐shaped N‐MoO_3?x electrode opens the way to integrate the electricity generation and storage for self‐powered sources.     

The Influence of Active Carbon Supports Toward the Electrocatalytic Behavior of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles for the Extended Energy Generation of Mediatorless Microbial Fuel Cells

Magnetite (Fe₃O₄) nanoparticles anchored over the different active carbon supports were developed by a simple wet solution method. The developed nanostructures were magnetically self-assembled over the electrode surface and exploited as anode catalysts in mediatorless microbial fuel cells (MFC). The morphological characterizations revealed that 3～8-nm-sized Fe₃O₄ nanoparticles were homogeneously anchored over the different carbon matrices and the obtained diffraction patterns ensured the cubic inverse spinel structure of prepared Fe₃O₄ nanoparticles. The morphology, size, and structure of Fe₃O₄ nanoparticles anchored over the different active carbon supports were maintained identical, and the influence of active carbon support toward the effectual MFC performances was evaluated under various electrochemical regimes and conditions by using Escherichia coli as a catalytic microorganism. The electrochemical characterizations revealed that carbon nanotube (CNT)-supported Fe₃O₄ nanoparticles exhibited lower charge transfer resistance and high coulombic efficiency in comparison with the graphene and graphite nanofiber-supported composites. Among the studied anode catalysts, Fe₃O₄/CNT composite exhibited the maximum MFC power density of 865 mW m^?2 associated with excellent durability performances, owing to the specific interaction exerted between the microorganisms and the Fe₃O₄/CNT composite. Thus, the binder-free electrode modification process, mediatorless environment, rapid electron transfer kinetics, high power generation, and long durability performances achieved for the developed system paved futuristic dimensions for the high performance MFCs.     

Design of Clayware Separator-Electrode Assembly for Treatment of Wastewater in Microbial Fuel Cells

Performance of six different microbial fuel cells (MFCs) made from baked clayware, having 450 ml effective anodic chamber volume, was evaluated, with different configurations of separator electrode assemblies, to study the feasibility of bioelectricity generation and high-strength wastewater treatment in a single-chambered mediator-less air-cathode MFC. Superior performance of an air-cathode MFC (ACMFC) with carbon coating on both sides of the separator was observed over an aqueous cathode MFC, resulting in a maximum volumetric power of 4.38 W m^?3 and chemical oxygen demand (COD) removal efficiency of more than 90 % in a batch cycle of 4 days. Hydrophilic polymer polyvinyl alcohol (PVA) was successfully used as a binder. The problem of salt deposition and fouling of cathode could be minimized by using a sock net current collector, replacing the usual stainless steel wire. However, electrolyte loss due to evaporation is a problem that needs to be resolved for better performance of an ACMFC.     

Electricity generation by an enriched phototrophic consortium in a microbial fuel cell

Microbial fuel cell (MFC) technology is a novel electricity generation process catalyzed by microorganisms. Much progress is made in the design and construction of MFCs, however the diversity of the electrochemically active microorganisms and the electricity generation mechanisms remain a black box. As sun is a predominantly unused energy resource, here we present a highly enriched phototrophic consortium that can produce electricity in an “H” typed MFC at a high power density (2650 mW m⁻², normalized to membrane area) in light, which was eightfold of that produced by non-enriched consortium in the same reactor. Light–dark shift experiments showed that light contributed to the electricity generation. A microbial excreted mediator assisted the electron transfer to the electrode. During the experiment, the accumulation of the mediator over time enhanced the electron transfer rate. The excitation–emission matrix fluorescence spectroscopy results indicated indole group containing compound representing the dominant mediator component.     

Using 3D Composite Electrode Materials for Electricity Generation from Swine Wastewater in a Dual‐Chamber Microbial Fuel Cells

Swine wastewater has a high concentration of organic matter, suspended solids, and higher ammonia nitrogen, odor, complex polluting ingredients, and large emissions. A two‐chambered cubic microbial fuel cell (MFC) was used to evaluate the effect of a novel three‐dimensional (3D ) electrode made of 3D iron composites and 3D stainless composites on the electricity generation. Swine wastewater with a total chemical oxygen demand (TCOD ) of 3688 ± 300 mg/L was used as the feedstock in the anode chamber. The MFC reactor was incubated with an initial pH of 7.0 in an air shaker with a temperature of ~35°C and 100 rpm in the fed‐batch mode. A fixed external resistance (R ) of 100 Ω was connected between the electrodes, and the closed‐circuit potentials of the MFCs were recorded every 5 min. The results showed that using an iron–carbon fiber composite 3D electrode resulted in a peak electricity generation of 321 mV on the first 2 days and maintained a stable voltage of 163 mV during the second to sixth days. The COD removal efficiency could reach 75%. Using a stainless–carbon fiber 3D electrode could generate a peak voltage of only 29.5 mV and a stable voltage of 15.2 mV with a COD removal efficiency of 54%.     

Electricity production of a microbial fuel cell stack integrated into a sink drain pipe

In this study, five two-chambered microbial fuel cells (MFCs) were hydraulically connected in series to constitute a MFC stack, which was integrated into a sink drain pipe for kitchen wastewater treatment. Performances of the MFC stack operating with artificial and real wastewater were studied. Considering the practical application, the voltage response to different flow rates and temperatures of the substrate was also investigated. It was found that the MFC stack could achieve a reasonable performance, with an average open circuit voltage of 3.44 ± 0.02 V, a peak power of 45.74 ± 1.39 mW (i.e. 809.27 mW/m²) and a coulombic efficiency of 78.2 ± 3.6 %. The MFC performance was disturbed by the flushing process, but could recover after a few minutes. The results also suggest that the MFC stack can operate after flushing by the substrate at 50 °C, above which irreversible performance deterioration was observed. The proposed MFC stack is expected to serve as a potential power source for lighting and low-power devices, especially in off-grid rural areas.     

微生物阳极燃料电池极性反转现象研究

本文在构建出微生物阳极燃料电池系统的基础上,研究了微生物燃料电池极性反转现象. 实验表明,由活性污泥混合菌源接种的微生物阳极在电极表面形成电化学生物膜,但平行构建的微生物阳极燃料电池系统在内阻、输出电压和放电时长等方面存在着不同程度差异. 在串联微生物燃料电池组中,放电操作会导致性能较差的微生物单电池首先出现极性反转. 电极电势测量表明,较高的放电电流使微生物阳极电势迅速正移,导致电池系统出现极性反转. 在室温范围内,温度升高可使MFC承受较高的放电电流,不易发生极化. 燃料物质缺乏时,MFC易发生极性反转,但过高的电流仍能使燃料物质充分的MFC出现极性反转. MFC极性反转会对微生物阳极性能造成影响. 极性反转时间较短(<5 min),对微生物阳极影响不大,但延长极性反转时间,会导致微生物阳极性能下降.     

Effect of Inoculum Types on Bacterial Adhesion and Power Production in Microbial Fuel Cells

Microbial fuel cell (MFC) is an emerging biotechnology to convert the organic substrates in wastewater to electricity by anaerobic electrogenic bacteria. The main challenge for MFC research is to elucidate the fundamental mechanisms of electron generation and transfer and to apply these mechanisms to improve the power production in the engineering operation. This study extensively investigated the effects of three inocula (Geobacter sulfurreducens, soil, and wastewater) on the power production and electrochemical characteristics (i.e., internal resistances, Coulombic Efficiency) of MFCs. The results showed that the extents of bacterial adhesion varied between mixed cultures (soil) and pure cultures (G. sulfurreducens). The voltage output increased 30% when bacterial adhesion was well-developed in the soil inocula. Meanwhile, the inoculum types clearly affected the internal resistance (R _in) and power production of MFCs. Pure culture inoculum (G. sulfurreducens) had the lowest R _in (165 Ω) and the highest Coulombic Efficiency (CE, 25.8%) and Energy Conversion Efficiency (ECE, 7.2%), while the mixed culture inocula (soil) with the high concentration of nonelectrogenic bacteria, exhibited the highest R _in (620 Ω), lowest CE (9.2%) and lowest ECE (2.4%). Additionally, a second-order correlation was established between the anode potential (P _A) and power output while an exponential correlation was established between the difference between anode and cathode potentials (ΔP _C−A) and power output.     

Microfuel cells: Modern state and future development (Review)

Literature sources of the last 15 years were analyzed and the results were considered for the studies carried out in one of the directions of hydrogen power engineering of the most current interest: development of portable low-power fuel cells (microfuel cells, MFCs). MFCs with high power density and high efficiency are used as a basis for a new generation of power sources for various stand-alone electronic devices. The latest silicon micro- and nanotechnologies are considered, same as the technologies for obtaining nanostructured catalysts and problems regarding development of MFCs with the power of 0.5–20 W, methods of catalytic layers application in MFCs, choice of fuel, and methods of supplying it into MFCs, and MFC water managemen and temperature control. Special attention was paid to borohydride MFCs, combined (hybrid) systems, and MFCs with a mixed reagent. The results of electrochemical tests of MFC layouts are presented.     

Effects of different Pt-M (M = Fe,Co, Ni) alloy as cathodic catalyst on the performance of two-chambered microbial fuel cells

For the purpose of reducing the cost and improving the performance of cathodes in microbial fuel cells (MFCs), we prepared Pt/C and Pt-M/C (M = Ni, Co, Fe) electrodes, and characterized them by SEM, XRD and CV. The modified electrodes were used as the cathodes in double-chambered MFCs fed with synthetic medium and molasses sewage respectively. We have found that Pt-M/C catalysts had a better catalytic activity for oxygen reduction than Pt/C in the following order: Pt-Fe/C > Pt-Co/C > Pt-Ni/C > Pt/C. The maximum power density of the MFCs with Pt-M/C cathode was improved by 18–31% compared with the MFC with Pt/C cathode because of the decrease of activation loss in the cathode. This study shows that Pt-M/C catalysts can improve power generation of MFCs without affecting the COD removal and it is proposed that Pt-Fe functions best among the three Pt-M alloys as an efficient and cost-effective catalyst of MFCs.