Radiation-induced polymerization of glass-forming systems. II. Effect of temperature on the polymerization rate at higher conversion

The effect of temperature and conversion on the polymerization rate at higher conversion was investigated with regard to the γ-ray-induced polymerization of hydroxyethyl methacrylate (HEMA) and glycidyl methacrylate (GMA) in the supercooled phase. The polymerization rate changed from acceleration to depression at various conversions, depending on the polymerization temperature. It was found that T_v at which the viscosity of the system became ca. 10³ cpoise influenced the shape of the polymerization time–conversion curve. The experimentally obtained conversion reflection point in the polymerization time–conversion curve agreed with the conversion where the polymerization temperature is the same as the calculated T_v of the system. When the polymerization temperature was lower than T_v of the monomer, no acceleration of the polymerization occurred. When the polymerization temperature was higher than T_v of the polymer, no depression of the polymerization rate was observed. The effect of temperature on the saturated conversion (final conversion) was also examined in terms of T_g of the polymerization system. The experimentally obtained saturated conversion agreed with the conversion where the polymerization temperature is the same as the calculated T_g of the system.     

Radiation-induced polymerization of glass-forming systems. IV. Effect of the homogeneity of polymerization phase and polymer concentration on temperature dependence of initial polymerization rate

The effect of homogeneity of polymerization phase and monomer concentration on the temperature dependence of initial polymerization rate was studied in the radiation-induced radical polymerization of binary systems consisting of glass-forming monomer and solvent. In the polymerization of a completely homogeneous system such as HEMA–propylene glycol, a maximum and a minimum in polymerization rates as a function of temperature, characteristic of the polymerization in glass-forming systems, were observed for all monomer concentrations. However, in the heterogeneous polymerization systems such as HEMA–triacetin and HEMA–isoamyl acetate, maximum and minimum rates were observed in monomer-rich compositions but not at low monomer concentrations. Furthermore, in the HEMA–dioctyl phthalate polymerization system, which is extremely heterogeneous, no maximum and minimum rates were observed at any monomer concentration. The effect of conversion on the temperature dependence of polymerization rate in homogeneous bulk polymerization of HEMA and GMA was investigated. Maximum and minimum rates were observed clearly in conversions less than 10% in the case of HEMA and less than 50% in the case of GMA, but the maximum and minimum changed to a mere inflection in the curve at higher conversions. A similar effect of polymer concentration on the temperature dependence of polymerization rate in the GMA–poly(methyl methacrylate) system were also observed. It is deduced that the change in temperature dependence of polymerization rate is attributed to the decrease in contribution of mutual termination reaction of growing chain radicals to the polymerization rate.     

Radiation-induced polymerization of glass forming systems. VI. Polymerization rate at higher conversion in binary systems

The effect of temperature and composition on the inflection point in the time–conversion curve and the saturated conversion was investigated in the radiation-induced radical polymerization of binary systems consisting of a glass-forming monomer and a solvent. In the polymerization of completely homogeneous systems such as glycidyl methacrylate (GMA)–triacetin and hydroxyethyl methacrylate (HEMA)–propylene glycol systems, the time–conversion curve has an inflection point at polymerization temperatures between T_vm (T_v of monomer system) and T_vp (T_v of polymer system). Such conversions at the inflection point changed monotonically between 0 and 100% in this temperature range. T_v was found to be 30–50°C higher than T_g (glass transition temperature) and a monotonic function of composition (monomer–polymer–solvent). The acceleration effect continued to 100% conversion above T_vp, and no acceleration effect was observed below T_vm. The saturated conversion in homogeneous systems changed monotonically between 0 and 100% for polymerization temperatures between T_gm (T_g of monomer system) and T_gp (T_g of polymer system). T_g was also a monotonic function of composition. No saturation in conversion was observed above T_gp, and no polymerization occurred below T_gm. In the polymerization of completely heterogeneous systems such as HEMA–dioctyl phthalate, no acceleration effect was observed at any temperature and composition. The saturated conversion was 100% above T_g of pure HEMA, and no polymerization occurred below this temperature in this system.     

Radiation-induced polymerization of glass-forming systems. V. Initial polymerization rate in binary glass-forming systems

The radiation-induced polymerization of binary systems consisting of glass-forming monomer and glass-forming solvent in supercooled phase was studied. The initial polymerization rates were markedly affected by T_g (glass transition temperature) and T_v of the system (30–50°C higher than T_g), which turned to be functions of the composition. The composition and temperature dependence of initial polymerization rate in binary glass-forming systems were much affected by homogeneity of the polymerization system and the T_g of the glass-forming solvent. The composition and temperature dependences in the glycidyl methacrylate–triacetin system as a typical homogeneous polymerization system were studied in detail, and the polymerizations of hydroxyethyl methacrylate–triacetin and hydroxyethyl methacrylate–isoamyl acetate systems were studied for the heterogeneous polymerization systems; the former illustrates the combination of lower T_g monomer and higher T_g solvent and the latter typifies a system consisting of higher T_g monomer and lower T_g solvent. All experimental results for the composition and temperature dependence of initial polymerization rate in binary glass-forming systems could be explained by considering the product of the effect of the physical effect relating to T_v and T_g of the system and the effect of composition in normal solution polymerization at higher temperature, which was also the product of a dilution effect and a chemical or physical acceleration effect.     

Radiation-induced polymerization of glass-forming systems. VII. Polymerization in supercooled state under high pressure

Radiation-induced polymerization of glass-forming monomers such as 2-hydroxyethyl methacrylate and glycidyl methacrylate under high pressure was studied. The glass transition temperature of these monomers was heightened by increased pressure. The temperature dependence of polymerizability showed a characteristic relation; similar to those in supercooled-phase polymerization under normal pressure, that had a maximum at T_v which shifted to higher levels of temperature as well as to T_g under high pressure. Polymerizability in the supercooled state also increased under increased pressure.     

An NMR study of the electron beam-induced polymerization of trimethylolpropane triacrylate and trimethylolpropane trimethacrylate

Electron beam-induced polymerization of trimethylolpropane triacrylate (TMPTA) and its methacrylate analog (TMPTMA) was studied using nuclear magnetic resonance (NMR) relaxation time measurements. Free induction decays (FID) of partially polymerized samples consist of a short Gaussian component and a longer component comprised of a distribution of simple exponentials. The relative intensity of the Gaussian component increases with radiation dose. T₁ and T_1ρ values were measured as a function of temperature and radiation dose. The relaxation is due primarily to methyl group reorientation at low temperatures, ethyl group reorientation at intermediate temperatures, and whole-molecule reorientation at high temperatures. In both compounds, the T₁ and T_1ρ values at the high temperature minima increase with increasing dose, and the minima values can be used to estimate the degree of polymerization. The temperature at which the T_1ρ minimum occurs increases with dose, suggesting an increase in the glass transition temperature, T_g, with polymerization. The polymerization appears to have very little effect on the low temperature CH₃ reorientation in TMPTA. In TMPTMA the polymerization appears to reduce the mobility of the methacrylate methyl groups.     

A study of post-radiation polymerization of 2-hydroxyethyl methacrylate γ-irradiated in crystalline and vitreous states

Dependent on the mode of preparation, 2-hydroxyethyl methacrylate (HEMA) can at low temperatures acquire either vitreous or crystalline states. On heating γ-irradiated vitreous HEMA, polymerization starts immediately after transition of the system from the vitreous state to that of a supercooled liquid (T_g = 177 K). This provides conditions for growth of polymer chains and suppression of bimolecular termination of active growing centres. Polymerization of radiated crystalline HEMA occurs at higher temperatures in the monomer melting region. At equal dosages of preliminary radiation, the transformation depth for the crystalline sample is considerably lower than that for the vitreous sample; this effect is due to different molecular mobilities in heated crystalline and vitreous samples. In HEMA post-polymerization, the very early transformation stages yielded an insoluble cross-linked polymer. This paper discusses the possible mechanism of cross-linking during polymerization of monomers of the HEMA type as a result of detachment of hydrogen from the carbon atom in the glycol group.     

Radiation-induced solid-state polymerization in binary systems. IV. Solid-state polymerization in the glassy phase

The radiation-induced polymerization of glass-forming systems containing monomers has been investigated. It was found that irradiation below the second-order transition temperature T_g of the systems causes no in-source polymerization but causes a rapid postpolymerization on warming above the T_g after initial irradiation below the T_g. The post-polymerization was followed by differential thermal analysis and ESR spectra. It is caused above the T_g by the release of peroxy radicals trapped below the T_g, and its rate is proportional to the irradiation dose to some extent, often is explosively high, and brings about a remarkably large temperature rise by accumulation of polymerization heat. Irradiation above the T_g causes rapid in-source polymerization which is accelerated by the high viscosity of the monomeric system between T_g and T_s (WLF temperature) compared to crystal or ordinary solution polymerization. The temperature dependence of the in-source polymerization of glassy systems shows a peak between the T_g and T_s which may be the result of competing effects of the rate increase by the decreased termination near T_s and the rate decrease by the decreased propagation caused by the diffusion prevented near the T_g. The degree of polymerization was also investigated. The temperature dependence of the degree of polymerization of the polymers obtained by in-source polymerization shows a peak similar to that of the temperature dependence of conversion. Unusually large values of the Huggins constant k' are noted between T_g and T_s. The degree of polymerization of the polymer obtained by post-polymerized increases with the increase of irradiation dose and the polymerization rate; this may be the result of decreased chain transfer to nonpolymerizable components.     

Initial stage in radiation polymerization of hydroxyethyl methacrylate-water system at low temperatures

The initial stage in the radiation polymerization of the hydroxyethyl methacrylate water system at low temperatures was studied. The polymerization was accelerated by the presence of water; the effect increased with rising temperature above T_g. The polymerization rate had a maximum near ?50°. The initiating and propagating radicals were identified by studies with ESR. Irradiated hydroxyethyl methacrylate at low temperatures gave a 7-line spectrum, which was assigned to the initiating radical having equivalent protons. This spectrum was changed to a 9-line spectrum at ?120 to ?100°; it was assigned to the propagating radical. The temperature dependence of the ESR spectrum of irradiated hydroxyethyl methacrylate-water systems was studied to examine the effect of water on the propagating radical.     

GHD室温自交联乳液的聚合及贮存稳定性

采用半连续种子乳液聚合技术合成了含甲基丙烯酸缩水甘油酯(GMA)、甲基丙烯酸羟乙酯(HEMA)和甲基丙烯酸二甲氨基乙酯(DMAEMA)的室温自交联乳液(GHD).实验结果表明,在甲基丙烯酸甲酯(MMA)-丙烯酸丁酯(BA)-GMA种子乳液存在下,聚合温度升高,聚合过程稳定性下降,但乳液的贮存稳定性提高;乳化单体滴加速度加快,种子聚合物的玻璃化温度升高,可减少聚合过程的交联凝聚作用,提高聚合过程的稳定性;而HEMA和DMAEMA用量增加对聚合过程的稳定性没有明显影响,但使乳液的贮存稳定性下降.官能团间的交联凝聚作用可能是影响室温自交联乳液聚合及贮存过程稳定性的关键因素.     

Ionic Liquids - New Solvents in the Free Radical Polymerization

Summary: The analysis of the influence of ionic liquids (ILs) in polymer synthesis as an alternative for common organic solvents is still an active field of research. 1 Using ILs as solvents for free radical polymerizations implies a significant increase in polymerization rates and molecular weights which can be observed. In this work we examined the copolymerization behaviour of styrene (S) and methyl methacrylate (MMA), glycidyl methacrylate (GMA) and 2-hydroxypropyl methacrylate (HPMA) with acrylonitrile (AN) in 1-etyhl-3-methylimidazolium ethylsulfate ([EMIM]EtSO₄). ILs are liquids with comparable high polarities and viscosities. These two characteristic properties are strongly correlated with the rate coefficients of propagation k_p and termination k_t. 2 - 4 The rate constant of termination k_t decreases when the IL concentration and therefore the viscosity of the reaction mixture is increased, whereas the propagation rate coefficient k_p increases with increasing IL content. The viscosity of the IL can be varied by either working with mixtures of IL with conventional organic solvents – here the IL [EMIM]EtSO₄ was mixed with DMF – or by variation of the temperature. The influence of the viscosity of the IL ([EMIM]EtSO₄) on polymerization kinetics of methyl methacrylate (MMA) and styrene/acrylonitrile (S/AN) was investigated.     

Ionic complex of Vanadyl(IV) in the polymerization of 2-hydroxyethyl methacrylate as probed by EPR

The vanadyl ionic complex VO(DMSO)₅(ClO₄)₂ (I) exhibits high catalytic activity in the polymerization of 2-hydroxyethyl methacrylate (HEMA). The changes in the vanadium oxidation state during polymerization under argon and in the presence of oxygen were studied by EPR. Under aerobic conditions, the HEMA chain propagation radical was detected; this indicates the presence of a radical chain polymerization pathway caused by the ability of I to perform one-electron reduction of molecular O₂. The radical generation rate is controlled by the initial concentration of I: its increase results in the formation of inactive species, presumably, μ-peroxo complexes V^v-O-O-V^v. It was shown by kinetic methods that the radical-chain pathway initiated by the reaction of I with O₂ is not crucial in the HEMA polymerization.     

Simultaneous reversible addition fragmentation chain transfer and ring‐opening polymerization

The simultaneous ring‐opening polymerization (ROP) of ε‐caprolactone (ε‐CL) and 2‐hydroxyethyl methacrylate (HEMA) polymerization via reversible addition fragmentation chain transfer (RAFT) chemistry and the possible access to graft copolymers with degradable and nondegradable segments is investigated. HEMA and ε‐CL are reacted in the presence of cyanoisopropyl dithiobenzoate (CPDB) and tin(II) 2‐ethylhexanoate (Sn(Oct)₂) under typical ROP conditions (T > 100 °C) using toluene as the solvent in order to lead to the graft copolymer PHEMA‐g‐PCL. Graft copolymer formation is evidenced by a combination of size‐exclusion chromatography (SEC) and NMR analyses as well as confirmed by the hydrolysis of the PCL segments of the copolymer. With targeted copolymers containing at least 10% weight of PHEMA and relatively small PHEMA backbones (ca. 5,000–10,000 g mol^?1) the copolymer grafting density is higher than 90%. The ratio of free HEMA‐PCL homopolymer produced during the “one‐step” process was found to depend on the HEMA concentration, as well as the half‐life time of the radical initiator used. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3058–3067, 2008     

Radical polymerization of methyl methacrylate in the presence of stereoregular poly(methyl methacrylate). V. Kinetics of initial template polymerization

The influence of stereoregular poly(methyl methacrylate) (PMMA) as a polymer matrix on the initial rate of radical polymerization of methyl methacrylate (MMA) has been measured between ?11 and +60°C using a dilatometric technique. Under proper conditions an increase in the relative initial rate of template polymerization with respect to a blank polymerization was observed. Viscometric studies showed that the observed effect could be related to the extent of complex formation between the polymer matrix and the growing chain radical. The initial rate was dependent on tacticity and molecular weight of the matrix polymer, solvent type and polymerization temperature. The accelerating effect was most pronounced (a fivefold increase in rate) at the lowest polymerization temperature with the highest molecular weight isotactic PMMA as a matrix in a solvent like dimethylformamide (DMF), which is known to be a good medium for complex formation between isotactic and syndiotactic PMMA. The acceleration of the polymerization below 25°C appeared to be accompanied by a large decrease in the overall energy and entropy of activation. It is suggested that the observed template effects are mainly due to the stereoselection in the propagation step (lower activation entropy Δ S_p^?) and the hindrance of segmental diffusion in the termination step (higher activation energy Δ E_t^?) of complexed growing chain radicals.     

Effects of polymerization method on structure and properties of thermoplastic polyurethanes

The effects of the dynamic polymerization method and temperature on the molecular aggregation structure and the mechanical and melting properties of thermoplastic polyurethanes (TPUs) were successfully clarified. TPUs were prepared from poly (ethylene adipate) glycol (M_n = 2074), 4,4′‐diphenylmethane diisocyanate and 1,4‐butanediol by the one‐shot (OS) and the prepolymer (PP) methods in bulk at dynamic polymerization temperatures ranging from 140 to 230 °C. Glass‐transition temperatures (T_gs) of the soft segment and melting points (T_ms) of the hard segment domains of OS‐TPUs increased and decreased, respectively, with increasing polymerization temperatures, but those of PP‐TPUs were almost independent of the polymerization temperature. T_gs of the soft segment and T_ms of the hard segment domains of these TPUs polymerized above 190 °C were almost the same regardless of the polymerization method. Solid‐state nuclear magnetic resonance spectroscopy (NMR) analyses of OS‐ and PP‐TPUs showed that the relative proton content of fast decay components, which corresponds to the hard segment domains, in these TPUs decreased with increasing polymerization temperatures. These results clearly show that the degree of microphase separation becomes weaker with increasing polymerization temperatures. The temperature dependence of dynamic storage modulus and loss tangent of OS‐TPUs coincided with those of PP‐TPUs at polymerization temperature above 190 °C. The apparent shear viscosity for OS‐ and PP‐TPUs polymerized above 190 °C approached a Newtonian behavior at low shear rates regardless of the polymerization method. These results indicate that TPUs polymerized at higher temperatures form almost the same molecular aggregation structures irrespective of the dynamic polymerization method. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 800–814, 2007     

Effect of triphenyl phosphite on the radical polymerization of styrene and methyl methacrylate

The effects of triphenyl phosphite (TPP) on the radical polymerization of styrene (St) and methyl methacrylate (MMA) initiated with α,α,-azobisisobutyronitrile (AIBN) was investigated at 50°C. The rate of polymerization of St and MMA at a constant concentration of TPP was found to be proportional to the monomer concentration and the square root of the initiator concentration. The rate of polymerization and the degree of polymerization of both St and MMA increased with increasing TPP concentration. The accelerating effect was shown to be due to the decrease of the termination rate constant k_t with an increase in the viscosity of the polymerization systems. The chain transfer constant C_tr of TPP in St and MMA systems was determined from the degree of polymerization system. The C_tr of TPP was almost zero in the St system and 6.5 × 10^?5 in the MMA system.     

Kinetics of emulsion polymerization of methyl methacrylate

The kinetics of the emulsion polymerization of methyl methacrylate at 50°C have been studied in seeded systems using both chemical initiation and γ-radiolysis initiation. Both steady-state rates and (for γ-radiolysis) the relaxation from the steady state were observed. The average number of free radicals per particle was quite high (e.g., ～0.7 for 10^?3 mol dm^?3 S₂O²₈ initiator). The data are quantitatively interpreted using a generalized Smith–Ewart–Harkins model, allowing for free radical entry, exit, biomolecular termination within the latex particles, and aqueous phase hetero-termination and re-entry. From this treatment, there results (i) the dependence of the termination rate coefficient (k_t) on the weight fraction of polymer (w_p), (ii) lower bounds for the dependence of the entry rate coefficient on initiator concentration, and (iii) the conclusion that most exited free radicals undergo subsequent re-entry into particles rather than hetero-termination. The results for k_t(w_p) are consistent with diffusion control at temperatures below the glass transition point. Comparisons are presented of the behavior of methyl methacrylate, butyl methacrylate, and styrene in emulsion polymerization systems.     

Polymerization of coordinated monomers. I. Stereoregulation in the free-radical polymerization of methyl methacrylate-zinc chloride or methyl methacrylate–stannic chloride complexes

Stereoregulation in free-radical polymerization was studied for the polymerization of the 2:1 or 1:1 complex of methyl methacrylate with ZnCl₂ or SnCl₄. The complexes were polymerized with the use of a free-radical initiator or γ-ray irradiation either in the liquid or solid state at various temperatures ranging from ?196 to 110°C, and the tacticities of the resulting polymers were determined by NMR spectroscopy. The polymers had different and characteristic values of tacticities depending upon the complex species, i.e., the kind of metal chloride and the stoichiometry. The tacticities were found to be independent of the polymerization temperature in both the liquid and solid states, in contrast with the fact that tacticities of the polymer from pure monomer changed markedly with the temperature. A temperature dependence appeared in the polymerization system, which contained more monomer than that corresponding to the 2:1 complex. The effect of the viscosity or the solid phase on the stereoregulation was examined in comparison with the polymerization of a mixture of methyl methacrylate and liquid paraffin. Two possible explanations regarding the stereoregulation mechanism are offered in relation to the structures of the complexes.     

The dependence of craze velocity on the pressure and temperature of the environmental gas

The craze velocity was determined for poly(chlorotrifluoroethylene) (PCTFE) in CH₄ and for PCTFE, polystyrene, and poly(methyl methacrylate) in N₂. It was found that for temperatures near the boiling point the velocity and number of crazes depended on the relative pressure given by P exp[-(Q_v/R) (T_B^?1 - T^?1)], where P is the pressure, Q_v is the heat of vaporization, and T_B is the boiling point. The craze velocity was related to the coverage of the adsorbed gas. For coverages corresponding to a few monolayers the logarithm of the velocity was proportional to the relative pressure. As the temperature increases from T_B, the creep rate decreases because gas desorbs with increasing temperature; the creep rate attains a minimum value at a temperature where the general process of thermally activated deformation becomes dominant.     

Diffusion-controlled vinyl polymerization. IV. Comparison of theory and experiment

Bulk polymerization data of methyl methacrylate, ethyl methacrylate, ethyl acrylate, n-propyl acrylate, vinyl acetate, and styrene were compared with the predictions of the theory proposed in the earlier parts of this series (I-III). This theory of polymerization kinetics uses the concepts of free volume and chain entanglements to describe the relationship between chain mobility and chain length dependent termination reactions. Excellent agreement was found between the predictions of the theory and the polymerization rate and molecular weight data of the six polymerization systems studied. Emphasis was placed on the ability to explain the development of higher order molecular weight averages (M?_w, M?_z, etc.) because they provide the most crucial tests for such a model. No changes were required in the model as it was applied to the different polymerization systems for a variety of reaction conditions. The theory offers a unified understanding of the diverse polymerization behavior displayed by such systems.