Interatomic potential for the X1Σ state of Be2, revisited

An extended geminal model has been applied to determine the interatomic potential for the X¹Σ state of Be₂. By adopting a (23s, 10p, 8d, 6f, 3g, 2h) uncontracted Gaussian‐type basis, the following spectroscopic parameters are obtained: R_e = 4.633 a.u. (4.63 a.u.), D_e = 945 ± 15 cm (790 ± 30 cm), G(1)–G(0) = 221.7 cm^?1 (223.8 ± 2 cm^?1), G(2)–G(1) = 175.0 cm^?1 (169 ± 3 cm^?1), G(3)–G(2) = 123.1 cm^?1 (122 ± 3 cm^?1), and G(4)–G(3) = 80.8 cm^?1 (79 ± 3 cm^?1), experimental values in parentheses. The calculated binding energy is substantially higher than the accepted experimental value. © 2004 Wiley Periodicals, Inc. Int J Quantum Chem, 2005     

Thermodynamic and kinetic behaviour of salicylsalicylic acid

The thermal behaviour of salicylsalicylic acid (CAS number 552-94-3) was studied by differential scanning calorimetry (DSC). The endothermic melting peak and the fingerprint of the glass transition were characterised at a heating rate of 10°C min^-1. The melting peak showed an onset at T _on = 144°C (417 K) and a maximum intensity at T _max = 152°C (425 K), while the onset of the glass transition signal was at T _on = 6°C. The melting enthalpy was found to be Δ_mH = 28.9±0.3 kJ mol^-1, and the heat capacity jump at the glass transition was ΔC _P = 108.1±0.1 J K^-1mol^-1. The study of the influence of the heating rate on the temperature location of the glass transition signal by DSC, allowed the determination of the activation energy at the glass transition temperature (245 kJ mol^-1), and the calculation of the fragility index of salicyl salicylate (m = 45). Finally, the standard molar enthalpy of formation of crystalline monoclinic salicylsalicylic acid at T = 298.15 K, was determined as Δ_fH_m ^o(C₁₄H₁₀O₅, cr) = - (837.6±3.3) kJ mol^-1, by combustion calorimetry. This revised version was published online in August 2006 with corrections to the Cover Date.     

Phase Diagram of R(+)-S(-) Efaroxan Hydrochloride

The phase diagram of R(+)-S(-) efaroxan hydrochloride (T_fus.(R)=245.1±0.3°C. ΔH_fus.(R)=119.6±3.0 J g^-1) shows a racemic compound. The melting temperature and melting enthalpy of the compound are: T_fus.(RS)=247.8±0.2°C and ΔH_fus. (RS)=124.6±2.4 J g^-1. A solid ↔ solid transformation takes place at T_trs.=180±1°C, ΔH_trs.=15.0±0.4 J g^-1. This transition is observed between 3 and 97% R(+). The stability of the racemic compound already established in a previous study was confirmed by the value of Petterson's coefficient (i=1.19). The two eutectic positions at 20 and 80% R(+) that define the range over which the racemic compound is found, exclude the use of resolution methods by preferential crystallization. This revised version was published online in July 2006 with corrections to the Cover Date.     

Evaluation of crosslinking and scission yields in the degradation of polystyrene by γ-irradiation in air

A sample of polystyrene with narrow molecular weight distribution (M?_w/M?_n = 1.03) has been formed into a 3-mm sheet and subjected to γ-irradiation at 25°C in air. Simultaneous crosslinking and scission of polymer chains resulted. Analyses by velocity and equilibrium sedimentation, gelpermeation chromatography, and osmometry of the polystyrene subjected to doses in the range 0-90 Mrad, all within the pre-gel region, have yielded average values of G(S) = G(X) = 0.022 ± 0.002 for the complete sample. Combination of these various experimental techniques has been successful in yielding consistent values of G(S) and G(X) and should be applicable with advantage to other polymers, particularly when neither G(S) nor G(X) is zero. The wide variation in literature values of G(S) and G(X) for irradiation of polystyrene under vacuum precludes any unequivocal conclusion on the effect of air on the radiation yields.     

Synthesis and characterization of tough polycyclic polyamides containing 4,9-Diamantyl moieties in the main chain

A series of new polyamides were synthesized by direct polycondensation of the 4,9-diamantane dicarboxylic acid ( I ) with various aromatic diamines in N-methyl-2-pyrrolidone (NMP) containing lithium chloride. The polyamides had inherent viscosities of 0.56–1.85 dL/g. Dynamic mechanical analysis revealed the polymers IIIa–IIId to have main melting transitions at 403, 431, 423, and 452°C, respectively. Moreover, these polymers were quite stable at high temperatures and maintained good mechanical properties (G′ = ca. 10⁸ Pa) up to temperatures close to the main transition well above 400°C. Although the polyamides contained rigid 4,9-diamantyl moieties in the main chain, the tensile properties of the polyamides showed toughness. Elongations of polyamides IIIa and IIIb reached 38.3 and 31.7%, respectively, before breaking. A glass transition was not observed. However, polyamide IIIc shows a melting transition with a sharp endothermic peak at 423°C by DSC measurement. Additionally, the introduction of 4,9-diamantyl units into the polyamide backbone resulted in polyamides with high thermal stability and good mechanical properties. © 1996 John Wiley & Sons, Inc.     

Characterization,crystallization kinetics,and melting behavior of poly(ethylene succinate) copolyester containing 10 mol % butylene succinate

Copolyester was synthesized and characterized as having 89.9 mol % ethylene succinate units and 10.1 mol % butylene succinate units in a random sequence, as revealed by NMR. Isothermal crystallization kinetics was studied in the temperature range (T_c) from 30 to 73 °C using differential scanning calorimetry (DSC). The melting behavior after isothermal crystallization was investigated using DSC by varying the T_c, the heating rate and the crystallization time. DSC curves showed triple melting peaks. The melting behavior indicates that the upper melting peaks are associated primarily with the melting of lamellar crystals with various stabilities. As the T_c increases, the contribution of recrystallization slowly decreases and finally disappears. A Hoffman‐Weeks linear plot gives an equilibrium melting temperature of 107.0 °C. The spherulite growth of this copolyester from 80 to 20 °C at a cooling rate of 2 or 4 °C/min was monitored and recorded using an optical microscope equipped with a CCD camera. Continuous growth rates between melting and glass transition temperatures can be obtained after curve‐fitting procedures. These data fit well with those data points measured in the isothermal experiments. These data were analyzed with the Hoffman and Lauritzen theory. A regime II → III transition was detected at around 52 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2431–2442, 2008     

Mass Spectrometric Investigations of Thermodynamic Properties of the RbCl/GdCl3 System

The vaporization of pure RbCl, GdCl₃, and RbCl‐GdCl₃ samples of different phase compositions was investigated in the temperature range between 666 K and 982 K by use of the Knudsen effusion mass spectrometry. The gaseous species RbCl, Rb₂Cl₂, GdCl₃, and RbGdCl₄ were identified in the equilibrium vapours and their partial pressures were determined. The enthalpy of dissociation of RbGdCl₄(g), Δ_dissH°(859 K) = 263.1 ± 7.7 kJ mol^—1, was evaluated by second law treatment of the equilibrium partial pressures. The thermodynamic activities of RbCl and GdCl₃ were obtained at 800 K in the two‐phase fields {Rb₃GdCl₆(s) + liquid} and {RbGd₂Cl₇(s) + GdCl₃(s)}. The Gibbs free energies of formation of the pseudo‐binary phases Rb₃GdCl₆(s), Δ_fG°(800 K) = —75.1 ± 2.5 kJ mol^—1 and RbGd₂Cl₇(s), Δ_fG°(800 K) = —40.6 ± 1.2 kJ mol^—1, were evaluated from the thermodynamic activities of the components. The results are compared with the available literature data.     

Melting temperature of trans-polyoctenamer

The effect of microstructure on crystallizability of polyoctenamers prepared by R₃Al-WCl₆ catalyst was studied. The results indicate that polyoctenamers with a broad range of trans-vinylene content do crystallize. The measured melting points are dependent on the trans-vinylene content. From the dependence of melting temperature on copolymer composition, a value of 73 ± 2°C. for the melting point and a molar heat of fusion ΔH_u of 3520 cal./mole are calculated for 100% trans-polyoctenamer. From the melting point depression in the presence of diluent, a value for ΔH_u of 4800 cal./mole is obtained.     

Irradiation of aromatic polymers: The effect of irradiation temperature on crosslinking and scission in polystyrene

Polystyrene of narrow molecular weight distribution, M _w/M _n ≈ 1.03, was subjected to γ irradiation at 100 and 150°C. The yields of scission and crosslinking, G(S) and G(X), where determined from the changes in molecular weight distribution using gel permeation chromatography, (GPC) with supporting evidence from osmometry and viscometry. The ratio G(S)/G(X) increased from 0.02 at 30°C, obtained previously, to 2.8 at 150°C. This was mainly due to a tenfold increase in G(S), whereas G(X) apparently decreased slightly. These results are compatible with increased disproportion of chain scission radicals relative to their combination, analogous to the temperature dependence of mutual termination in the free radical polymerization of styrene. There was no obvious discontinuity through the glass transition temperature, although there may be a change in sign of the temperature coefficient of G(X). This system provides an excellent example of the applicability of measurements of molecular weight distributions and averages to determinations of G(S) and G(X) under conditions when gel measurements are inappropriate, either because of the failure of the system to form gel, or, as in the present case, because of the very large radiation doses required for gel formation.     

The electronic effects of substituents at the acyl carbon in the gas-phase elimination kinetics of tert-butyl α-substituted acetates

The gas-phase eliminations of several tert-butyl esters, in a static system and in vessels seasoned with allyl bromide, have been studied in the temperature range of 171.5–280.1°C and the pressure range of 23–98 torr. The rate coefficients for the homogeneous unimolecular elimination of these esters are given by the following Arrhenius equations: for tert-butyl pivalate, log k₁(s^?1) = (13.44 ± 0.30) ? (169.1 ± 3.1) kJ · mol^?1 (2.303RT)^?1; for tert-butyl trichloroacetate, log k₁(s^?1) = (12.41 ± 0.08) ? (141.1 ± 0.7) kJ · mol^?1 (2.303RT)^?1; and for tert-butyl cyanoacetate log k₁(s^?1) = (11.31 ± 0.44) ? (137.8 ± 4.1) kJ · mol^?1 (2.303RT)^?1. The data of this work together with those reported in the literature yield a good linear relationship when plotting log k/k₀ vs. σ* values (ρ* = 0.635, correlation coefficient r = 0.972, and intercept = 0.048 at 250°C). The positive ρ* value suggests that the movement of negative charge to the acyl carbon in the transition state is rate determining. The present results along with previous investigations ratify the generalization that electron-withdrawing substituents at the acyl side of ethyl, isopropyl, and tert-butyl esters enhance the elimination rates, while electron-releasing groups tend to reduce them. The negative nature of the acyl carbon and the polarity in the transition state increases slightly from primary to tertiary esters.     

Heat capacities and thermodynamic properties of chrysanthemic acid

The heat capacities of chrysanthemic acid in the temperature range from 80 to 400 K were measured with a precise automatic adiabatic calorimeter. The chrysanthemic acid sample was prepared with the purity of 0.9855 mole fraction. A solid-liquid fusion phase transition was observed in the experimental temperature range. The melting point, T _m, enthalpy and entropy of fusion, Δ_fus H _m, Δ_fus S _m, were determined to be 390.741±0.002 K, 14.51±0.13 kJ mol^-1, 37.13±0.34 J mol^-1 K^-1, respectively. The thermodynamic functions of chrysanthemic acid, H _(T)-H_(298.15), S _(T)-S_(298.15) and G _(T)-G ₍₂₉₈.₁₅₎ were reported with a temperature interval of 5 K. The TG analysis under the heating rate of 10 K min^-1 confirmed that the thermal decomposition of the sample starts at ca. 410 K and terminates at ca. 471 K. The maximum decomposition rate was obtained at 466 K. The purity of the sample was determined by a fractional melting method. This revised version was published online in July 2006 with corrections to the Cover Date.     

Photon correlation spectroscopy of bulk poly(n-hexyl methacrylate) near the glass transition

Slowly relaxing longitudinal density fluctuations in an optically perfect sample of bulk poly(n-hexyl methacrylate) (PHMA) have been studied by photon correlation spectroscopy in the temperature range 10–36°C. The glass transition temperature for this sample was measured to be T_g = −3°C by differential scanning calorimetry. The optical purity of the sample was verified by Rayleigh-Brillouin spectroscopy and the Landau-Placzek ratio was observed to be 2.3 at 25°C. Light-scattering relaxation functions were obtained over the time range 10⁻⁶-1 s. The shape of the relaxation functions broadened as the temperature was lowered towards the glass transition. Quantitative analysis of the results was carried out using the Kohlrausch-Williams-Watts (KWW) function to obtain average relaxation times, 〈τ〉, and width parameters, β. The width parameter decreased from 0.43 to 0.21 over the temperature interval, as suggested by visual inspection. Average relaxation times shifted with temperature in a manner consistent with previous mechanical studies of the primary glass-rubber relaxation in PHMA. The relaxation functions were also analyzed in terms of a distribution of relaxation rates, G(Γ). The calculated distributions were unimodal at all temperatures. The average relaxation times obtained from G(Γ) were in agreement with the KWW analysis, and the shape of the distribution broadened as the sample was cooled. The rate at which G(Γ) displayed a maximum correlated well with the corresponding frequency of maximum dielectric loss for PHMA. The temperature dependence of these two quantities could be reproduced with an Arrhenius activation energy of 21 Kcal/mol. A consistent picture of the molecular dynamics of PHMA near the glass transition requires a strong secondary relaxation process with a different temperature dependence from the primary glass-rubber relaxation. The present results suggest that the behavior of PHMA is similar to the other poly(alkyl methacrylates). © 1996 John Wiley & Sons, Inc.     

The dissociation of 3-chloro-1-butene and the resonance energy of the chloro-allyl radical

Methane is a primary product of pyrolysis of 3-chloro-l-butene at temperatures in the range 776–835°K, and from its rate of formation values have been obtained for the limiting high-pressure rate constant of the reaction These may be represented by the expression log [(k₁)_∞/sec^?1] = (16.7 ± 0.3) ? (71.5 ± 1.5)/θ, where θ = 2.303RT kcal/mole. Assuming a zero activation energy for the reverse reaction and that over the experimental temperature range the rates at which a methyl radical adds on to chlorobutene are comparable to those at which it abstracts hydrogen, the activation energy for the dissociation reaction leads to a value of 83.2 ± 1.9 ckal/mole for D(H? CHClCH:CH₂) at 298°K. Taking D(H? CHClCH₂CH ₃) = 95.2 ± 1.0 kcal/mole a value of 12.0 ± 2.1 kcal/mole is obtained for the resonance energy of the chloroallyl radical. This value in conjunction with resonance energies obtained in earlier work indicates that substitution of a hydrogen atom on the carbon atom adjacent to the double bond in the allyl radical leads to no significant variation in the allylic resonance energy.     

Darstellung und kristallographische Daten von Diamminzinkacetat,Zn(NH3)2(OCOCH3)2

Zn(NH₃)₂(OCOCH₃)₂ crystallizes from solutions obtained by dissolving ZnO in a methanolic solution of ammonium acetate. The pycnometrically determined density is 1.824 g cm^?3 at 23°C. From X-ray rotation photographs the dimensions of the monoclinic unit cell, containing eight formula units, were found to be:a=11.64±0.05,b=5.54±0.05,c=23.28±0.05 Å, β=93.6±0.5°. The probable space group is C₂/m-C_2h ³.     

The elimination kinetics and mechanisms of ethyl piperidine‐3‐carboxylate,ethyl 1‐methylpiperidine‐3‐carboxylate,and ethyl 3‐(piperidin‐1‐yl)propionate in the gas phase

The gas‐phase elimination kinetics of the above‐mentioned compounds were determined in a static reaction system over the temperature range of 369–450.3°C and pressure range of 29–103.5 Torr. The reactions are homogeneous, unimolecular, and obey a first‐order rate law. The rate coefficients are given by the following Arrhenius expressions: ethyl 3‐(piperidin‐1‐yl) propionate, log k₁(s^?1) = (12.79 ± 0.16) ? (199.7 ± 2.0) kJ mol^?1 (2.303 RT)^?1; ethyl 1‐methylpiperidine‐3‐carboxylate, log k₁(s^?1) = (13.07 ± 0.12)–(212.8 ± 1.6) kJ mol^?1 (2.303 RT)^?1; ethyl piperidine‐3‐carboxylate, log k₁(s^?1) = (13.12 ± 0.13) ? (210.4 ± 1.7) kJ mol^?1 (2.303 RT)^?1; and 3‐piperidine carboxylic acid, log k₁(s^?1) = (14.24 ± 0.17) ? (234.4 ± 2.2) kJ mol^?1 (2.303 RT)^?1. The first step of decomposition of these esters is the formation of the corresponding carboxylic acids and ethylene through a concerted six‐membered cyclic transition state type of mechanism. The intermediate β‐amino acids decarboxylate as the α‐amino acids but in terms of a semipolar six‐membered cyclic transition state mechanism. © 2005 Wiley Periodicals, Inc. Int J Chem Kinet 38: 106–114, 2006     

Thermochemical properties of the Fe-analogue of cryolite, Na3FeF6

Relative enthalpies for low-and high-temperature modifications of Na₃FeF₆ and for the Na₃FeF₆ melt have been measured by drop calorimetry in the temperature range 723–1318 K. Enthalpy of modification transition at 920 K, δ_trans H(Na₃FeF₆, 920 K) = (19 ± 3) kJ mol⁻¹ and enthalpy of fusion at the temperature of fusion 1255 K, δ_fusH(Na₃FeF₆, 1255 K) = (89 ± 3) kJ mol⁻¹ have been determined from the experimental data. Following heat capacities were obtained for the crystalline phases and for the melt, respectively: C _p(Na₃FeF₆, cr, α) = (294 ± 14) J (mol K)⁻¹, for 723 = T/K ≤ 920, C _p(Na₃FeF₆, cr, β) = (300 ± 11) J (mol K)⁻¹ for 920 ≤ T/K = 1233 and C _p(Na₃FeF₆, melt) = (275 ± 22) J (mol K)⁻¹ for 1258 ≤ T/K ≤ 1318. The obtained enthalpies indicate that melting of Na3FeF6 proceeds through a continuous series of temperature dependent equilibrium states, likely associated with the production of a solid solution.      

Properties of crystallized trans 1,4-polyisoprene

Stirrer crystallization of a trans-1,4-polyisoprene fraction(M?_n = 3 × 10⁵) was carried out from n-butyl acetate and from n-heptane solutions (2% w/v). Fibrous crystals in the ß form were obtained at temperatures of 46-48°C in the two solvents, respectively. At 36-46°C from n-butyl acetate and 25-35°C from n-heptane lamellar crystallization took place leading predominantly to the α form. Melting endotherms and densities for various samples were obtained. The maximum TENDO for α was 74°C and for ß 79°C and the maximum weight fraction crystallinity for ß was 0.78. The stability of performed α nuclei in n-butyl acetate and n-heptane using a fraction with M?_n = 2.5 × 10⁵ was monitored as a function of temperature. The dissolution temperature of fibrous ß-TPI with the maximum TENDO was measured in 13 liquids and the results analyzed in terms of the Flory-Huggins parameter. The heats of fusion for the α and ß forms, obtained by extrapolation of heat of fusion versus change in specific volume, were found to be 8.0 and 10 kJ mol^?1, respectively. The pressure coefficients of the melting temperature were calculated to be 38 and 43 K kbar^?1 and the fold-surface free energies recalculated to be 42 ± 1 and 53 ± 1 erg cm^?2 for the α and ß forms, respectively. The number of monomer units per average noncrystalline chain traverse for the most crystalline fibrous ß-TPI was estimated at 36.     

Analysis of crystallization kinetics of poly(ether ether ketone)

An optical microscope equipped with a video photograph system was used to follow the growth of spherulites. Under nitrogen atmosphere, the growth rates at 290 and 300°C suggest that when the melt of PEEK has been equilibrated for 15 min at 400°C, the subsequent crystallization behavior was nearly independent of the prior thermal history. Linear growth rates of crystallization of PEEK have been measuredin the temperature range of 260–325°C for melt-pressed films and solvent cast films. Detailed kinetic analysis indicated that PEEK exhibited an unmistakable regime II → III transition at 296 ± 1°C. The II → III transition was clearly present irrespective of the rather drastic changes in U*. It is interesting that the branching and crosslinking retarded the growth rate of PEEK, but a transition from regime II to regime III still existed. For melt-pressed films after equilibration at 400°C for 15 min, values of σ and q suggest that U* should be taken nearer to 1500 cal/mol in the case of T_∞ = T_g − 30 K and 2000 cal/mol in the case of T_∞ = T_g − 51.6 K. The K_g(III)/K_g(II) ratio (1.32) was not as close to the predicted value of 2 as was Hoffman's ratio. For PEEK, the Thomas-Staveley constant (β) should be closer to 0.25 or 0.3 instead of 0.1. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1335–1348, 1998     

Enthalpy of formation of wulfenite (natural lead molybdate)

A thermochemical study of wulfenite, i.e., natural lead molybdate PbMoO₄ (Kyzyl-Espe field deposit, Central Kazakhstan), is performed on a Setaram high-temperature heat-flux Tian-Calvet microcalorimeter (France). Enthalpies of the formation of wulfenite from oxides Δ_f H _ox ^o (298.15 K) = ?88.5 ± 4.3 kJ/mol and simple substances Δ_f H°(298.15 K) = ?1051.2 ± 4.3 kJ/mol were determined by means of melt calorimetry. The Δ_f G°(298.15 K) of wulfenite corresponding to ?949.1 ± 4.3 kJ/mol was calculated using data obtained earlier for S°(298.15 K) = 161.5 ± 0.27 J/(K mol).     

Bond dissociation energies and radical heats of formation in CH3Cl,CH2Cl2, CH3Br,CH2Br2, CH2FCl,and CHFCl2

An analysis of thermochemical and kinetic data on the bromination of the halomethanes CH_4–nX_n (X = F, Cl, Br; n = 1–3), the two chlorofluoromethanes, CH₂FCl and CHFCl₂, and CH₄, shows that the recently reported heats of formation of the radicals CH₂Cl, CHCl₂, CHBr₂, and CFCl₂, and the C? H bond dissociation energies in the matching halomethanes are not compatible with the activation energies for the corresponding reverse reactions. From the observed trends in CH₄ and the other halomethanes, the following revised ΔH°_f,298 (R) values have been derived: ΔH°_f(CH₂Cl) = 29.1 ± 1.0, ΔH°_f(CHCl₂) = 23.5 ± 1.2, ΔH_f(CH₂Br) = 40.4 ± 1.0, ΔH°_f(CHBr₂) = 45.0 ± 2.2, and ΔH°_f(CFCl₂) = ?21.3 ± 2.4 kcal mol^?1. The previously unavailable radical heat of formation, ΔH°_f(CHFCl) = ?14.5 ± 2.4 kcal mol^?1 has also been deduced. These values are used with the heats of formation of the parent compounds from the literature to evaluate C? H and C? X bond dissociation energies in CH₃Cl, CH₂Cl₂, CH₃Br, CH₂Br₂, CH₂FCl, and CHFCl₂.